[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (9 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9568556/tftp-deploy-zl3rjux1/kernel/zImage tftp 0x10000000 9568556/tftp-deploy-zl3rjux1/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9568556/tftp-deploy-zl3rjux1/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 5.5 MiB/s done Bytes transferred = 9691648 (93e200 hex) => tftp 0x14000000 9568556/tftp-deploy-zl3rjux1/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9568556/tftp-deploy-zl3rjux1/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9568556/tftp-deploy-zl3rjux1/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 12.2 MiB/s done Bytes transferred = 12142346 (b9470a hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9568556/tftp-deploy-zl3rjux1/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9568556/tftp-deploy-zl3rjux1/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9568556/tftp-deploy-zl3rjux1/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9568556/extract-nfsrootfs-aqjirqyi,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9568556/extract-nfsrootfs-aqjirqyi,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93e200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12142282 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.173-cip27 (KernelCI@build-j1167316-arm-gcc-10-multi-v7-defconfig-z9pvx) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sun Mar 12 07:44:19 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9568556/extract-nfsrootfs-aqjirqyi,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 937524K/1048576K available (13312K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 45516K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000026] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004145] Console: colour dummy device 80x30 [ 0.004199] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004216] pid_max: default: 32768 minimum: 301 [ 0.004395] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004418] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005048] CPU: Testing write buffer coherency: ok [ 0.005088] CPU0: Spectre v2: using BPIALL workaround [ 0.005348] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006059] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007761] rcu: Hierarchical SRCU implementation. [ 0.011569] EFI services will not be available. [ 0.011881] smp: Bringing up secondary CPUs ... [ 0.012682] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012690] CPU1: Spectre v2: using BPIALL workaround [ 0.013612] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013619] CPU2: Spectre v2: using BPIALL workaround [ 0.014523] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014531] CPU3: Spectre v2: using BPIALL workaround [ 0.014653] smp: Brought up 1 node, 4 CPUs [ 0.014666] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.014676] CPU: All CPU(s) started in SVC mode. [ 0.015251] devtmpfs: initialized [ 0.022487] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022728] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022755] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025883] pinctrl core: initialized pinctrl subsystem [ 0.027786] DMI not present or invalid. [ 0.028628] NET: Registered protocol family 16 [ 0.032105] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.034516] thermal_sys: Registered thermal governor 'step_wise' [ 0.034704] cpuidle: using governor menu [ 0.034896] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.207212] vdd1p1: supplied by regulator-dummy [ 0.214333] vdd3p0: supplied by regulator-dummy [ 0.221416] vdd2p5: supplied by regulator-dummy [ 0.228452] vddarm: supplied by regulator-dummy [ 0.235674] vddpu: supplied by regulator-dummy [ 0.242609] vddsoc: supplied by regulator-dummy [ 0.567112] No ATAGs? [ 0.567271] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.567282] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.571582] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.577882] Serial: AMBA PL011 UART driver [ 0.580669] printk: console [ramoops-1] enabled [ 0.580887] pstore: Registered ramoops as persistent store backend [ 0.580904] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.613596] iommu: Default domain type: Translated [ 0.614031] vgaarb: loaded [ 0.614971] SCSI subsystem initialized [ 0.615559] usbcore: registered new interface driver usbfs [ 0.615623] usbcore: registered new interface driver hub [ 0.615672] usbcore: registered new device driver usb [ 0.617236] i2c i2c-0: IMX I2C adapter registered [ 0.618570] i2c i2c-1: IMX I2C adapter registered [ 0.619446] i2c i2c-2: IMX I2C adapter registered [ 0.620869] pps_core: LinuxPPS API ver. 1 registered [ 0.620882] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.620913] PTP clock support registered [ 0.624862] clocksource: Switched to clocksource mxc_timer1 [ 1.778376] NET: Registered protocol family 2 [ 1.778834] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.780007] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.780053] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.780143] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.780289] TCP: Hash tables configured (established 8192 bind 8192) [ 1.780503] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.780554] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.780744] NET: Registered protocol family 1 [ 1.781362] RPC: Registered named UNIX socket transport module. [ 1.781378] RPC: Registered udp transport module. [ 1.781389] RPC: Registered tcp transport module. [ 1.781400] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.781417] PCI: CLS 0 bytes, default 64 [ 1.781902] Trying to unpack rootfs image as initramfs... [ 2.735690] Freeing initrd memory: 11860K [ 2.736237] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.736577] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.738437] Initialise system trusted keyrings [ 2.738742] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.744547] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.745359] NFS: Registering the id_resolver key type [ 2.745439] Key type id_resolver registered [ 2.745453] Key type id_legacy registered [ 2.745562] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.745577] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.745619] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.746086] Key type asymmetric registered [ 2.746104] Asymmetric key parser 'x509' registered [ 2.746165] bounce: pool size: 64 pages [ 2.746215] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.746231] io scheduler mq-deadline registered [ 2.746244] io scheduler kyber registered [ 2.787479] mxs-dma 110000.dma-apbh: initialized [ 2.792347] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.792373] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.854272] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.858969] SuperH (H)SCI(F) driver initialized [ 2.860001] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.861017] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 3.689290] printk: console [ttymxc1] enabled [ 3.695127] msm_serial: driver initialized [ 3.699507] STMicroelectronics ASC driver initialized [ 3.706627] STM32 USART driver initialized [ 3.722380] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.730061] panel-simple panel-lcd: Specify missing connector_type [ 3.736668] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.753206] brd: module loaded [ 3.766391] loop: module loaded [ 3.773548] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 3.781545] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 3.789574] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 3.797785] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 3.805535] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 3.813005] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 3.820314] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 3.830646] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 3.837678] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.846504] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.857052] scsi host0: ahci-imx [ 3.860665] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 3.881312] CAN device driver interface [ 3.886587] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 3.895851] pps pps0: new PPS source ptp0 [ 3.918203] fec 2188000.ethernet eth0: registered PHC device 0 [ 3.925643] e1000e: Intel(R) PRO/1000 Network Driver [ 3.930617] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.936616] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.942022] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.953929] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.961394] usbcore: registered new interface driver pegasus [ 3.967118] usbcore: registered new interface driver asix [ 3.972556] usbcore: registered new interface driver ax88179_178a [ 3.978707] usbcore: registered new interface driver cdc_ether [ 3.984595] usbcore: registered new interface driver smsc75xx [ 3.990407] usbcore: registered new interface driver smsc95xx [ 3.996210] usbcore: registered new interface driver net1080 [ 4.001907] usbcore: registered new interface driver cdc_subset [ 4.007881] usbcore: registered new interface driver zaurus [ 4.013528] usbcore: registered new interface driver cdc_ncm [ 4.022947] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.029504] ehci-pci: EHCI PCI platform driver [ 4.033990] ehci-platform: EHCI generic platform driver [ 4.039541] ehci-orion: EHCI orion driver [ 4.043779] SPEAr-ehci: EHCI SPEAr driver [ 4.048023] ehci-st: EHCI STMicroelectronics driver [ 4.053093] ehci-exynos: EHCI Exynos driver [ 4.057497] ehci-atmel: EHCI Atmel driver [ 4.061695] tegra-ehci: Tegra EHCI driver [ 4.065957] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.072160] ohci-pci: OHCI PCI platform driver [ 4.076671] ohci-platform: OHCI generic platform driver [ 4.082170] SPEAr-ohci: OHCI SPEAr driver [ 4.086393] ohci-st: OHCI STMicroelectronics driver [ 4.091469] ohci-atmel: OHCI Atmel driver [ 4.096655] usbcore: registered new interface driver usb-storage [ 4.111026] i2c /dev entries driver [ 4.134563] sdhci: Secure Digital Host Controller Interface driver [ 4.140779] sdhci: Copyright(c) Pierre Ossman [ 4.147999] Synopsys Designware Multimedia Card Interface Driver [ 4.156076] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.165471] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 4.170487] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 4.172531] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 4.180808] ledtrig-cpu: registered to indicate activity on CPUs [ 4.187999] usbcore: registered new interface driver usbhid [ 4.193581] usbhid: USB HID core driver [ 4.204204] NET: Registered protocol family 10 [ 4.207314] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 4.209658] Segment Routing with IPv6 [ 4.217472] ata1: SATA link down (SStatus 0 SControl 300) [ 4.219300] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.224713] ahci-imx 2200000.sata: no device found, disabling link. [ 4.231178] NET: Registered protocol family 17 [ 4.236880] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 4.237160] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 4.241351] can: controller area network core [ 4.259817] NET: Registered protocol family 29 [ 4.264271] can: raw protocol [ 4.266373] mmc2: new high speed SDHC card at address 59b4 [ 4.267274] can: broadcast manager protocol [ 4.273614] mmcblk2: mmc2:59b4 SD 14.7 GiB [ 4.276966] can: netlink gateway - max_hops=1 [ 4.286442] Key type dns_resolver registered [ 4.292424] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 4.292936] ThumbEE CPU extension supported. [ 4.299878] GPT:7812499 != 30863359 [ 4.304154] Registering SWP/SWPB emulation handler [ 4.307643] GPT:Alternate GPT header not at the end of the disk. [ 4.307648] GPT:7812499 != 30863359 [ 4.307655] GPT: Use GNU Parted to correct GPT errors. [ 4.318628] Loading compiled-in X.509 certificates [ 4.322011] mmcblk2: p1 p2 p3 [ 4.332346] pstore: Using crash dump compression: deflate [ 4.362775] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.370442] panel-simple panel-lcd: Specify missing connector_type [ 4.378219] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.397133] imx_usb 2184200.usb: No over current polarity defined [ 4.407432] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 4.412376] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 4.444816] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 4.451594] hub 1-0:1.0: USB hub found [ 4.455478] hub 1-0:1.0: 1 port detected [ 4.461905] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 4.478029] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.485903] panel-simple panel-lcd: Specify missing connector_type [ 4.493644] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.505833] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.513438] panel-simple panel-lcd: Specify missing connector_type [ 4.521129] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.530849] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.542894] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.550556] panel-simple panel-lcd: Specify missing connector_type [ 4.558352] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.571816] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 4.784840] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.986485] hub 1-1:1.0: USB hub found [ 4.990456] hub 1-1:1.0: 3 ports detected [ 5.005441] panel-simple panel-lcd: supply power not found, using dummy regulator [ 5.013077] panel-simple panel-lcd: Specify missing connector_type [ 5.020873] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.685270] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 7.714877] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.744912] Sending DHCP requests ., OK [ 7.788710] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 [ 7.796767] IP-Config: Complete: [ 7.800008] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 [ 7.810469] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) [ 7.818328] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 7.818334] nameserver0=192.168.201.1 [ 7.835713] Freeing unused kernel memory: 2048K [ 7.865799] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 8.714068] imx-ipuv3 2400000.ipu: IPUv3H probed [ 8.725741] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.733428] panel-simple panel-lcd: Specify missing connector_type [ 8.741683] imx-ipuv3 2800000.ipu: IPUv3H probed [ 8.750627] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.773242] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.781036] panel-simple panel-lcd: Specify missing connector_type [ 8.790404] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.810037] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.818414] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.826771] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.835141] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.836143] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.851080] panel-simple panel-lcd: Specify missing connector_type [ 8.860515] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.899635] caam 2100000.crypto: Entropy delay = 3200 [ 8.965492] caam 2100000.crypto: Instantiated RNG4 SH0 [ 8.977677] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 8.985596] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 8.993945] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 8.999610] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 9.001759] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 9.021098] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 9.026246] caam 2100000.crypto: Instantiated RNG4 SH1 [ 9.033840] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 9.040485] caam 2100000.crypto: job rings = 2, qi = 0 [ 9.054353] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 9.062336] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 9.069900] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 9.076528] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 9.083776] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 9.091792] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 9.097982] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 9.106906] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 9.135332] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.143594] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.152022] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.160327] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.170498] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.178381] panel-simple panel-lcd: Specify missing connector_type [ 9.187084] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.217346] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.225707] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.233993] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.242374] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.425146] caam algorithms registered in /proc/crypto [ 9.431696] caam 2100000.crypto: registering rng-caam [ 9.438506] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.446257] panel-simple panel-lcd: Specify missing connector_type [ 9.454369] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers ... done. [ 9.469720] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/init-prem[ 9.478477] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) ount ... [ 9.489539] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done. [ 9.498462] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Mounting root file system [ 9.508985] panel-simple panel-lcd: supply power not found, using dummy regulator ... Begin: Running /scripts/nfs-t[ 9.517829] panel-simple panel-lcd: Specify missing connector_type op ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. [ 9.619259] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 10.506669] systemd[1]: System time before build time, advancing clock. [ 10.563653] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 10.588179] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 10.627215] systemd[1]: Set hostname to . [ 11.461743] systemd[1]: Queued start job for default target Graphical Interface. [ 11.471150] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 11.483658] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 11.493392] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 11.536267] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 11.576129] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 11.616107] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 11.655212] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 11.695571] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 11.735595] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.747750] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 11.785976] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 11.815263] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 11.855222] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 11.885369] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 11.916094] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 12.201853] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 12.211719] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 12.246401] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 12.297672] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 12.348896] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 12.385608] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 12.426056] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 12.435268] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 12.447434] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 12.488397] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 12.529579] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 12.571664] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 12.608527] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 12.648605] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 12.687844] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 12.701149] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.744675] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.778556] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 12.818044] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 12.861336] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 12.896435] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 12.936172] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 12.995627] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply [ 13.292902] systemd-journald[278]: Received client request to flush runtime journal. Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.173-cip27 #1 SMP Sun Mar 12 07:44:19 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9568556/extract-nfsrootfs-aqjirqyi' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9568556/extract-nfsrootfs-aqjirqyi' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9568556/environment . /lava-9568556/environment / # /lava-9568556/bin/lava-test-runner /lava-9568556/0 /lava-9568556/bin/lava-test-runner /lava-9568556/0 + export TESTRUN_ID=0_dmesg + cd /lava-9568556/0/tests/0_dmesg + cat uuid + UUID=9568556_1.6.2.4.1[ 26.916832] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 27.056635] [ 27.129176] [ 27.209970] + set[ 27.220324] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9568556/environment / # . /lava-9568556/environment/lava-9568556/bin/lava-test-runner /lava-9568556/1 / # /lava-9568556/bin/lava-test-runner /lava-9568556/1 + export TESTRUN_ID=1_bootrr + cd /lava-9568556/1/tests/1_bootrr + cat uuid + UUID=9568556_1.6.2.4.5 [ 27.807518] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9568556/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds 120000.hdmi panel-lcd /lava-9568556/1/../bin/lava-test-case [ 28.934611] /lava-9568556/1/../bin/lava-test-case [ 29.018313] /lava-9568556/1/../bin/lava-test-case [ 29.065616] + set +x[ 29.096198] / #