Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 21:37:56, Jul 29 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 21:38:04, Jul 29 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gcbd7e30bf8 (Jul 29 2019 - 21:37:23 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 4 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1054 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:36:8d:e8 DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - 26:fe:94:50:e5:84 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - 7e:03:c1:4c:5e:15 , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 76:0b:e8:36:d2:19 , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 4e:50:15:96:3b:11 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - 46:58:3c:ec:b7:1d , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - 62:42:e4:26:80:d1 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 6a:4a:cd:5c:0c:dd , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 32:12:77:b5:2e:26 , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.11; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1170941/tftp-deploy-bl81fe2q/kernel/uImage tftp 0x80080000 1170941/tftp-deploy-bl81fe2q/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1170941/tftp-deploy-bl81fe2q/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 4.5 MiB/s done Bytes transferred = 43717184 (29b1240 hex) => tftp 0x91000000 1170941/tftp-deploy-bl81fe2q/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1170941/tftp-deploy-bl81fe2q/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1170941/tftp-deploy-bl81fe2q/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################# 2.9 MiB/s done Bytes transferred = 21641138 (14a37b2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1170941/tftp-deploy-bl81fe2q/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1170941/tftp-deploy-bl81fe2q/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.11 Filename '1170941/tftp-deploy-bl81fe2q/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 2.9 KiB/s done Bytes transferred = 19637 (4cb5 hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-07-13 1:41:05 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 43717120 Bytes = 41.7 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-07-13 1:41:10 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 21641074 Bytes = 20.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 0000000090007cb4 fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 5.10.173-cip27 (KernelCI@build-j1167318-arm64-gcc-10-defconfig-kselftest-kqzpv) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Sun Mar 12 07:43:37 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3f77c0-0x837e3f9fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 34 pages/cpu s100944 r8192 d30128 u139264 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) [ 0.000000] Memory: 14154852K/14612480K available (18816K kernel code, 4548K rwdata, 9452K rodata, 9728K init, 11276K bss, 424860K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] ftrace: allocating 58454 entries in 229 pages [ 0.000000] ftrace: allocated 229 pages with 5 groups [ 0.000000] Running RCU self tests [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080200000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080210000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080220000 [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008385] Console: colour dummy device 80x25 [ 0.012875] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.020677] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.024803] ... MAX_LOCK_DEPTH: 48 [ 0.029018] ... MAX_LOCKDEP_KEYS: 8192 [ 0.033406] ... CLASSHASH_SIZE: 4096 [ 0.037794] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.042270] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.046746] ... CHAINHASH_SIZE: 32768 [ 0.051221] memory used by lock dependency info: 6365 kB [ 0.056660] memory used for stack traces: 4224 kB [ 0.061485] per task-struct memory footprint: 1920 bytes [ 0.066988] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.077419] pid_max: default: 32768 minimum: 301 [ 0.082180] LSM: Security Framework initializing [ 0.086862] LSM support for eBPF active [ 0.090798] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.098467] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.109837] rcu: Hierarchical SRCU implementation. [ 0.117086] Platform MSI: gic-its@6020000 domain created [ 0.122653] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.130292] fsl-mc MSI: gic-its@6020000 domain created [ 0.135966] EFI services will not be available. [ 0.141418] smp: Bringing up secondary CPUs ... [ 0.147245] Detected PIPT I-cache on CPU1 [ 0.147264] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.147273] GICv3: CPU1: using allocated LPI pending table @0x0000008080230000 [ 0.147301] arch_timer: CPU1: Trapping CNTVCT access [ 0.147316] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.148789] Detected PIPT I-cache on CPU2 [ 0.148806] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.148815] GICv3: CPU2: using allocated LPI pending table @0x0000008080240000 [ 0.148837] arch_timer: CPU2: Trapping CNTVCT access [ 0.148850] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.150285] Detected PIPT I-cache on CPU3 [ 0.150297] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.150305] GICv3: CPU3: using allocated LPI pending table @0x0000008080250000 [ 0.150320] arch_timer: CPU3: Trapping CNTVCT access [ 0.150331] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.151708] Detected PIPT I-cache on CPU4 [ 0.151727] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.151736] GICv3: CPU4: using allocated LPI pending table @0x0000008080260000 [ 0.151757] arch_timer: CPU4: Trapping CNTVCT access [ 0.151771] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.153125] Detected PIPT I-cache on CPU5 [ 0.153137] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.153145] GICv3: CPU5: using allocated LPI pending table @0x0000008080270000 [ 0.153161] arch_timer: CPU5: Trapping CNTVCT access [ 0.153172] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.154554] Detected PIPT I-cache on CPU6 [ 0.154573] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.154583] GICv3: CPU6: using allocated LPI pending table @0x0000008080280000 [ 0.154605] arch_timer: CPU6: Trapping CNTVCT access [ 0.154621] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.155997] Detected PIPT I-cache on CPU7 [ 0.156010] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.156018] GICv3: CPU7: using allocated LPI pending table @0x0000008080290000 [ 0.156034] arch_timer: CPU7: Trapping CNTVCT access [ 0.156045] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.156340] smp: Brought up 1 node, 8 CPUs [ 0.370381] SMP: Total of 8 processors activated. [ 0.375152] CPU features: detected: 32-bit EL0 Support [ 0.380380] CPU features: detected: CRC32 instructions [ 0.385574] CPU features: detected: 32-bit EL1 Support [ 0.418046] CPU: All CPU(s) started at EL2 [ 0.422273] alternatives: patching kernel code [ 0.428794] devtmpfs: initialized [ 0.444915] KASLR enabled [ 0.448641] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.458479] futex hash table entries: 2048 (order: 6, 262144 bytes, linear) [ 0.466536] pinctrl core: initialized pinctrl subsystem [ 0.474305] DMI not present or invalid. [ 0.479053] NET: Registered protocol family 16 [ 0.486149] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.493702] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.502911] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.511091] audit: initializing netlink subsys (disabled) [ 0.516822] audit: type=2000 audit(0.352:1): state=initialized audit_enabled=0 res=1 [ 0.518662] thermal_sys: Registered thermal governor 'step_wise' [ 0.524648] thermal_sys: Registered thermal governor 'power_allocator' [ 0.532759] cpuidle: using governor menu [ 0.543598] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.550762] ASID allocator initialised with 32768 entries [ 0.558519] Serial: AMBA PL011 UART driver [ 0.608433] Machine: Freescale Layerscape 2088A RDB Board [ 0.613895] SoC family: QorIQ LS2088A [ 0.617581] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.665626] HugeTLB registered 2.00 MiB page size, pre-allocated 256 pages [ 0.672657] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.679419] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.686182] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.695867] cryptd: max_cpu_qlen set to 1000 [ 0.705368] ACPI: Interpreter disabled. [ 0.712885] iommu: Default domain type: Translated [ 0.718285] vgaarb: loaded [ 0.721798] SCSI subsystem initialized [ 0.726407] usbcore: registered new interface driver usbfs [ 0.732048] usbcore: registered new interface driver hub [ 0.737506] usbcore: registered new device driver usb [ 0.743621] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.751498] i2c i2c-0: IMX I2C adapter registered [ 0.756825] pps_core: LinuxPPS API ver. 1 registered [ 0.761841] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.771174] PTP clock support registered [ 0.775411] EDAC MC: Ver: 3.0.0 [ 0.781354] fsl-ifc 2240000.ifc: Freescale Integrated Flash Controller [ 0.788020] fsl-ifc 2240000.ifc: IFC version 2.0, 8 banks [ 0.793907] FPGA manager framework [ 0.797561] Advanced Linux Sound Architecture Driver Initialized. [ 0.805330] clocksource: Switched to clocksource arch_sys_counter [ 1.403137] VFS: Disk quotas dquot_6.6.0 [ 1.407208] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.414743] pnp: PnP ACPI: disabled [ 1.434138] NET: Registered protocol family 2 [ 1.439028] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 1.451067] tcp_listen_portaddr_hash hash table entries: 8192 (order: 7, 655360 bytes, linear) [ 1.460650] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 1.470700] TCP bind hash table entries: 65536 (order: 10, 4718592 bytes, vmalloc) [ 1.484952] TCP: Hash tables configured (established 131072 bind 65536) [ 1.492527] MPTCP token hash table entries: 16384 (order: 8, 1441792 bytes, linear) [ 1.502281] UDP hash table entries: 8192 (order: 8, 1310720 bytes, linear) [ 1.511310] UDP-Lite hash table entries: 8192 (order: 8, 1310720 bytes, linear) [ 1.520675] NET: Registered protocol family 1 [ 1.526152] RPC: Registered named UNIX socket transport module. [ 1.532158] RPC: Registered udp transport module. [ 1.536913] RPC: Registered tcp transport module. [ 1.541667] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.548182] NET: Registered protocol family 44 [ 1.552688] PCI: CLS 0 bytes, default 64 [ 1.557120] Unpacking initramfs... [ 2.493522] Freeing initrd memory: 21128K [ 2.499301] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 2.507442] kvm [1]: IPA Size Limit: 44 bits [ 2.517791] kvm [1]: vgic-v2@c0e0000 [ 2.521444] kvm [1]: GIC system register CPU interface enabled [ 2.527737] kvm [1]: vgic interrupt IRQ9 [ 2.532120] kvm [1]: Hyp mode initialized successfully [ 2.546777] Initialise system trusted keyrings [ 2.551591] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 2.582464] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.589780] NFS: Registering the id_resolver key type [ 2.594965] Key type id_resolver registered [ 2.599210] Key type id_legacy registered [ 2.603518] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.610302] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.618045] 9p: Installing v9fs 9p2000 file system support [ 2.646491] Key type asymmetric registered [ 2.650663] Asymmetric key parser 'x509' registered [ 2.655647] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 2.663127] io scheduler mq-deadline registered [ 2.667708] io scheduler kyber registered [ 2.672087] test_firmware: interface ready [ 2.696202] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 2.703663] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 2.712322] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 2.721265] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 2.728034] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.733575] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 2.739816] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 2.750499] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 2.756588] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 2.762926] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 2.769265] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 2.776523] pci 0000:00:00.0: supports D1 D2 [ 2.780839] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 2.788187] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 2.794360] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 2.801089] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 2.807827] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 2.813501] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 2.820313] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 2.827780] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 2.845947] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 2.853162] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 2.860371] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 2.868022] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 2.875314] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 2.881567] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 2.888789] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 2.896432] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 2.903647] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 2.910875] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 2.917047] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 2.922330] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 2.928487] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 2.936817] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 2.944268] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 2.952932] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 2.961838] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 2.968610] pci_bus 0001:00: root bus resource [bus 00-ff] [ 2.974154] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 2.983195] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 2.993850] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 2.999962] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 3.007195] pci 0001:00:00.0: supports D1 D2 [ 3.011513] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 3.019203] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 3.026848] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 3.035351] EINJ: ACPI disabled. [ 3.067753] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 3.080477] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 16, base_baud = 21875000) is a 16550A [ 3.091145] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 16, base_baud = 21875000) is a 16550A [ 3.100173] printk: console [ttyS1] enabled [ 3.100173] printk: console [ttyS1] enabled [ 3.108586] printk: bootconsole [uart8250] disabled [ 3.108586] printk: bootconsole [uart8250] disabled [ 3.120008] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 17, base_baud = 21875000) is a 16550A [ 3.130470] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 17, base_baud = 21875000) is a 16550A [ 3.140339] SuperH (H)SCI(F) driver initialized [ 3.145802] msm_serial: driver initialized [ 3.154556] arm-smmu 5000000.iommu: probing hardware configuration... [ 3.161038] arm-smmu 5000000.iommu: SMMUv2 with: [ 3.165678] arm-smmu 5000000.iommu: stage 1 translation [ 3.171012] arm-smmu 5000000.iommu: stage 2 translation [ 3.176345] arm-smmu 5000000.iommu: nested translation [ 3.181592] arm-smmu 5000000.iommu: coherent table walk [ 3.186930] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 3.194092] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 3.200651] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 3.207114] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 3.213577] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 3.250587] loop: module loaded [ 3.254909] lkdtm: No crash points registered, enable through debugfs [ 3.263181] megasas: 07.714.04.00-rc1 [ 3.269147] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 3.277013] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 3.284587] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 3.292613] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.301602] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 3.314125] scsi host0: ahci-qoriq [ 3.318340] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 104 [ 3.326672] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 3.334475] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 3.342040] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 3.349987] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 3.358974] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 3.370080] scsi host1: ahci-qoriq [ 3.373967] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 105 [ 3.383339] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 3.392651] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 3.402771] Amd/Fujitsu Extended Query Table at 0x0040 [ 3.407942] Amd/Fujitsu Extended Query version 1.3. [ 3.413020] number of CFI chips: 1 [ 3.445992] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 3.452421] nand: Micron MT29F16G08ABABAWP [ 3.456537] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 3.465667] Bad block table found at page 524160, version 0x01 [ 3.473496] Bad block table found at page 524032, version 0x01 [ 3.512296] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 3.523192] spi-nor spi0.0: unrecognized JEDEC id bytes: 87 0e 1e 3c 38 70 [ 3.531926] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 3.538859] spi-nor: probe of spi1.0 failed with error -2 [ 3.551639] thunder_xcv, ver 1.0 [ 3.554983] thunder_bgx, ver 1.0 [ 3.558316] nicpf, ver 1.0 [ 3.563276] hclge is initializing [ 3.566706] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 3.573949] hns3: Copyright (c) 2017 Huawei Corporation. [ 3.579376] e1000: Intel(R) PRO/1000 Network Driver [ 3.584273] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 3.590129] e1000e: Intel(R) PRO/1000 Network Driver [ 3.595111] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.601534] e1000e 0000:01:00.0: Adding to iommu group 0 [ 3.607800] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 3.639926] ata1: SATA link down (SStatus 0 SControl 300) [ 3.666246] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 3.695934] ata2: SATA link down (SStatus 0 SControl 300) [ 3.728089] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:36:8d:e8 [ 3.736099] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 3.743017] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 3.749873] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.755296] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.760968] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 3.767257] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 3.773905] sky2: driver version 1.30 [ 3.779547] VFIO - User Level meta-driver version: 0.3 [ 3.791031] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.797632] ehci-pci: EHCI PCI platform driver [ 3.802168] ehci-platform: EHCI generic platform driver [ 3.807614] ehci-orion: EHCI orion driver [ 3.811830] ehci-exynos: EHCI Exynos driver [ 3.816215] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.822441] ohci-pci: OHCI PCI platform driver [ 3.826968] ohci-platform: OHCI generic platform driver [ 3.832410] ohci-exynos: OHCI Exynos driver [ 3.837364] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.842980] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.850897] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 3.860406] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x03100000 [ 3.866980] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.872505] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.880218] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 3.888483] hub 1-0:1.0: USB hub found [ 3.892384] hub 1-0:1.0: 1 port detected [ 3.897379] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.906746] hub 2-0:1.0: USB hub found [ 3.910584] hub 2-0:1.0: 1 port detected [ 3.915493] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.921113] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 3.929012] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 3.938503] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x03110000 [ 3.945056] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.950581] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 3.958274] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.966097] hub 3-0:1.0: USB hub found [ 3.969934] hub 3-0:1.0: 1 port detected [ 3.974707] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.984038] hub 4-0:1.0: USB hub found [ 3.987871] hub 4-0:1.0: 1 port detected [ 3.992942] usbcore: registered new interface driver usb-storage [ 4.003909] i2c /dev entries driver [ 4.012231] i2c i2c-0: Added multiplexed i2c bus 1 [ 4.121713] rtc-ds3232: probe of 2-0068 failed with error -110 [ 4.127694] i2c i2c-0: Added multiplexed i2c bus 2 [ 4.133395] i2c i2c-0: Added multiplexed i2c bus 3 [ 4.139068] i2c i2c-0: Added multiplexed i2c bus 4 [ 4.144394] i2c i2c-0: Added multiplexed i2c bus 5 [ 4.149735] i2c i2c-0: Added multiplexed i2c bus 6 [ 4.155052] i2c i2c-0: Added multiplexed i2c bus 7 [ 4.160364] i2c i2c-0: Added multiplexed i2c bus 8 [ 4.165192] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 4.178060] sp805-wdt c000000.wdt: registration successful [ 4.184054] sp805-wdt c010000.wdt: registration successful [ 4.190055] sp805-wdt c100000.wdt: registration successful [ 4.196036] sp805-wdt c110000.wdt: registration successful [ 4.202022] sp805-wdt c200000.wdt: registration successful [ 4.208005] sp805-wdt c210000.wdt: registration successful [ 4.213981] sp805-wdt c300000.wdt: registration successful [ 4.219958] sp805-wdt c310000.wdt: registration successful [ 4.235712] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 4.247578] sdhci: Secure Digital Host Controller Interface driver [ 4.253784] sdhci: Copyright(c) Pierre Ossman [ 4.259110] Synopsys Designware Multimedia Card Interface Driver [ 4.266886] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.276166] ledtrig-cpu: registered to indicate activity on CPUs [ 4.285436] usbcore: registered new interface driver usbhid [ 4.291051] usbhid: USB HID core driver [ 4.301226] optee: probing for conduit method. [ 4.301465] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 4.305717] optee: api uid mismatch [ 4.317085] optee: probe of firmware:optee failed with error -22 [ 4.326655] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 4.333012] IPv4 over IPsec tunneling driver [ 4.339491] NET: Registered protocol family 10 [ 4.346367] Segment Routing with IPv6 [ 4.351839] NET: Registered protocol family 17 [ 4.357050] 9pnet: Installing 9P2000 support [ 4.361493] Key type dns_resolver registered [ 4.366389] registered taskstats version 1 [ 4.370557] Loading compiled-in X.509 certificates [ 4.391424] pcieport 0000:00:00.0: Adding to iommu group 1 [ 4.398614] pcieport 0000:00:00.0: PME: Signaling with IRQ 112 [ 4.406140] pcieport 0001:00:00.0: Adding to iommu group 2 [ 4.413195] pcieport 0001:00:00.0: PME: Signaling with IRQ 116 [ 6.854433] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 6.865533] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.885485] Sending DHCP requests .., OK [ 10.257509] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.171 [ 10.265165] IP-Config: Complete: [ 10.268459] device=eth0, hwaddr=68:05:ca:36:8d:e8, ipaddr=172.16.1.171, mask=255.255.255.0, gw=172.16.1.4 [ 10.278535] host=172.16.1.171, domain=example.org, nis-domain=(none) [ 10.285381] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 10.285397] nameserver0=172.16.1.4 [ 10.297080] ALSA device list: [ 10.300244] No soundcards found. [ 10.322219] Freeing unused kernel memory: 9728K [ 10.326981] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 10.461610] udevd[190]: starting version 3.2.9 [ 10.467610] random: udevd: uninitialized urandom read (16 bytes read) [ 10.474683] random: udevd: uninitialized urandom read (16 bytes read) [ 10.481212] random: udevd: uninitialized urandom read (16 bytes read) [ 10.492686] udevd[190]: specified user 'tss' unknown [ 10.497911] udevd[190]: specified group 'tss' unknown [ 10.506707] udevd[191]: starting eudev-3.2.9 [ 10.959464] lm90 4-004c: supply vcc not found, using dummy regulator [ 10.975683] ina2xx 3-0040: error configuring the device: -11 [ 10.984879] SError Interrupt on CPU4, code 0xbf000002 -- SError [ 10.984881] CPU: 4 PID: 213 Comm: udevd Not tainted 5.10.173-cip27 #1 [ 10.984882] Hardware name: Freescale Layerscape 2088A RDB Board (DT) [ 10.984884] pstate: 60000000 (nZCv daif -PAN -UAO -TCO BTYPE=--) [ 10.984885] pc : 0000ffffaeb88170 [ 10.984886] lr : 0000ffffaeb8dd48 [ 10.984887] sp : 0000ffffe8396600 [ 10.984888] x29: 0000ffffe83966e0 x28: 000000000000000c [ 10.984891] x27: 0000ffffe8396748 x26: 0000000000429da1 [ 10.984894] x25: 000000000aba9500 x24: 0000000000000000 [ 10.984897] x23: 0000000000429cee x22: 0000000000429ca7 [ 10.984900] x21: 000000000044e000 x20: 0000ffffe8396bb0 [ 10.984902] x19: 0000ffffe8396ba0 x18: 00000000000007f8 [ 10.984905] x17: 0000ffffaeb8dd04 x16: 000000000044dff8 [ 10.984908] x15: 0000000000000016 x14: 0000000000000000 [ 10.984910] x13: 0000000000000007 x12: 0000000000000001 [ 10.984913] x11: 0000000000000000 x10: 0000000000000000 [ 10.984915] x9 : 0000000000000016 x8 : 0000000000000039 [ 10.984918] x7 : 0000000000000007 x6 : 0000000000000000 [ 10.984921] x5 : 0000000000000000 x4 : 00000000149cf700 [ 10.984924] x3 : 0000000000000007 x2 : 0000000000000000 [ 10.984926] x1 : 0000000000000b58 x0 : 0000ffffaebac1e0 [ 10.984929] Kernel panic - not syncing: Asynchronous SError Interrupt [ 10.984930] CPU: 4 PID: 213 Comm: udevd Not tainted 5.10.173-cip27 #1 [ 10.984932] Hardware name: Freescale Layerscape 2088A RDB Board (DT) [ 10.984933] Call trace: [ 10.984934] dump_backtrace+0x0/0x200 [ 10.984935] show_stack+0x20/0x30 [ 10.984936] dump_stack+0x110/0x160 [ 10.984937] panic+0x1b0/0x3a8 [ 10.984938] nmi_panic+0xb8/0xbc [ 10.984939] arm64_serror_panic+0x88/0x94 [ 10.984940] do_serror+0x64/0x6c [ 10.984941] el0_error_naked+0x18/0x20 [ 10.984942] [ 10.984943] ================================ [ 10.984944] WARNING: inconsistent lock state [ 10.984946] 5.10.173-cip27 #1 Not tainted [ 10.984947] -------------------------------- [ 10.984948] inconsistent {INITIAL USE} -> {IN-NMI} usage. [ 10.984949] udevd/213 [HC1[1]:SC0[0]:HE0:SE1] takes: [ 10.984951] ffffa86c6e670070 (safe_read_lock){....}-{2:2}, at: __printk_safe_flush+0x40/0x270 [ 10.984955] {INITIAL USE} state was registered at: [ 10.984957] lock_acquire.part.0+0xe0/0x230 [ 10.984958] lock_acquire+0x68/0x84 [ 10.984959] _raw_spin_lock_irqsave+0x80/0x154 [ 10.984960] __printk_safe_flush+0x40/0x270 [ 10.984961] printk_safe_flush+0x58/0xb0 [ 10.984962] printk_safe_init+0x90/0xa4 [ 10.984963] setup_log_buf+0x40/0x3e0 [ 10.984964] start_kernel+0x248/0x578 [ 10.984965] irq event stamp: 15534 [ 10.984967] hardirqs last enabled at (15533): [] finish_ret_to_user+0x4/0x16c [ 10.984968] hardirqs last disabled at (15534): [] el0_error_naked+0x8/0x20 [ 10.984969] softirqs last enabled at (11992): [] __do_softirq+0x5c8/0x648 [ 10.984971] softirqs last disabled at (11983): [] __irq_exit_rcu+0x174/0x1a0 [ 10.984972] [ 10.984973] other info that might help us debug this: [ 10.984974] Possible unsafe locking scenario: [ 10.984975] [ 10.984976] CPU0 [ 10.984977] ---- [ 10.984978] lock(safe_read_lock); [ 10.984980] [ 10.984981] lock(safe_read_lock); [ 10.984984] [ 10.984985] *** DEADLOCK *** [ 10.984985] [ 10.984987] no locks held by udevd/213. [ 10.984987] [ 10.984988] stack backtrace: [ 10.984990] CPU: 4 PID: 213 Comm: udevd Not tainted 5.10.173-cip27 #1 [ 10.984991] Hardware name: Freescale Layerscape 2088A RDB Board (DT) [ 10.984992] Call trace: [ 10.984993] dump_backtrace+0x0/0x200 [ 10.984994] show_stack+0x20/0x30 [ 10.984995] dump_stack+0x110/0x160 [ 10.984996] print_usage_bug.part.0+0x208/0x22c [ 10.984997] lock_acquire.part.0+0x210/0x230 [ 10.984998] lock_acquire+0x68/0x84 [ 10.984999] _raw_spin_lock_irqsave+0x80/0x154 [ 10.985001] __printk_safe_flush+0x40/0x270 [ 10.985002] printk_safe_flush+0x58/0xb0 [ 10.985003] printk_safe_flush_on_panic+0xb0/0xc0 [ 10.985004] panic+0x1b8/0x3a8 [ 10.985005] nmi_panic+0xb8/0xbc [ 10.985006] arm64_serror_panic+0x88/0x94 [ 10.985007] do_serror+0x64/0x6c [ 10.985008] el0_error_naked+0x18/0x20 [ 10.985027] SMP: stopping secondary CPUs [ 10.985029] Kernel Offset: 0x286c5c080000 from 0xffff800010000000 [ 10.985030] PHYS_OFFSET: 0xffffcfab40000000 [ 10.985031] CPU features: 0x28240022,21806008 [ 10.985032] Memory Limit: none