[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9334774/tftp-deploy-7bnfit9l/kernel/zImage tftp 0x10000000 9334774/tftp-deploy-7bnfit9l/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9334774/tftp-deploy-7bnfit9l/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 5.5 MiB/s done Bytes transferred = 12345856 (bc6200 hex) => tftp 0x14000000 9334774/tftp-deploy-7bnfit9l/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9334774/tftp-deploy-7bnfit9l/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9334774/tftp-deploy-7bnfit9l/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################### 11 MiB/s done Bytes transferred = 19396203 (127f66b hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9334774/tftp-deploy-7bnfit9l/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9334774/tftp-deploy-7bnfit9l/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9334774/tftp-deploy-7bnfit9l/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbc6200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19396139 Bytes = 18.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.170-cip27 (KernelCI@build-j1107502-arm-gcc-10-multi-v7-defconfig-kselftest-pvq6c) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Feb 25 18:26:27 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917580K/1048576K available (17408K kernel code, 2651K rwdata, 8100K rodata, 2048K init, 6691K bss, 65460K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 55428 entries in 163 pages <6>[ 0.000000] ftrace: allocated 163 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022827] Console: colour dummy device 80x30 <4>[ 0.024729] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032741] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037087] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041497] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046132] ... CLASSHASH_SIZE: 4096 <4>[ 0.050719] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055439] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060115] ... CHAINHASH_SIZE: 32768 <4>[ 0.064812] memory used by lock dependency info: 4061 kB <4>[ 0.070493] memory used for stack traces: 2112 kB <4>[ 0.075537] per task-struct memory footprint: 1536 bytes <6>[ 0.081226] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091642] pid_max: default: 32768 minimum: 301 <6>[ 0.096870] LSM: Security Framework initializing <6>[ 0.101435] LSM support for eBPF active <6>[ 0.105598] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.113034] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123641] CPU: Testing write buffer coherency: ok <6>[ 0.126194] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.132439] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141357] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147834] rcu: Hierarchical SRCU implementation. <6>[ 0.159762] EFI services will not be available. <6>[ 0.163031] smp: Bringing up secondary CPUs ... <6>[ 0.169846] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.169862] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.182300] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.182316] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.194410] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.194424] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.203627] smp: Brought up 1 node, 4 CPUs <6>[ 0.207298] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.213613] CPU: All CPU(s) started in SVC mode. <6>[ 0.221287] devtmpfs: initialized <6>[ 0.278597] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.286466] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.293903] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.305976] pinctrl core: initialized pinctrl subsystem <6>[ 0.315745] DMI not present or invalid. <6>[ 0.319314] NET: Registered protocol family 16 <6>[ 0.333455] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.347598] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.348164] cpuidle: using governor menu <6>[ 0.356332] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 1.114473] vdd1p1: supplied by regulator-dummy <6>[ 1.148948] vdd3p0: supplied by regulator-dummy <6>[ 1.182600] vdd2p5: supplied by regulator-dummy <6>[ 1.216288] vddarm: supplied by regulator-dummy <6>[ 1.250870] vddpu: supplied by regulator-dummy <6>[ 1.283422] vddsoc: supplied by regulator-dummy <6>[ 2.630246] No ATAGs? <6>[ 2.631176] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.638308] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.664465] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.699300] Serial: AMBA PL011 UART driver <6>[ 2.765559] Kprobes globally optimized <6>[ 2.888305] iommu: Default domain type: Translated <6>[ 2.893106] vgaarb: loaded <5>[ 2.898499] SCSI subsystem initialized <6>[ 2.901984] usbcore: registered new interface driver usbfs <6>[ 2.905824] usbcore: registered new interface driver hub <6>[ 2.911204] usbcore: registered new device driver usb <6>[ 2.924152] i2c i2c-0: IMX I2C adapter registered <6>[ 2.933533] i2c i2c-1: IMX I2C adapter registered <6>[ 2.940289] i2c i2c-2: IMX I2C adapter registered <6>[ 2.947256] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.949665] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.959183] PTP clock support registered <6>[ 2.981611] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.688742] NET: Registered protocol family 2 <6>[ 4.691403] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.701648] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.707671] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.715799] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.724680] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.730668] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.737688] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.744454] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.752255] NET: Registered protocol family 1 <6>[ 4.758814] RPC: Registered named UNIX socket transport module. <6>[ 4.762415] RPC: Registered udp transport module. <6>[ 4.767217] RPC: Registered tcp transport module. <6>[ 4.772258] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.778899] NET: Registered protocol family 44 <6>[ 4.783664] PCI: CLS 0 bytes, default 64 <6>[ 4.790355] Trying to unpack rootfs image as initramfs... <6>[ 7.363404] Freeing initrd memory: 18944K <4>[ 7.365853] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 7.373488] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 7.389999] Initialise system trusted keyrings <6>[ 7.393032] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 7.450498] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 7.457646] NFS: Registering the id_resolver key type <5>[ 7.460393] Key type id_resolver registered <5>[ 7.464678] Key type id_legacy registered <6>[ 7.469469] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 7.475938] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 7.483717] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 7.490236] Key type asymmetric registered <5>[ 7.492605] Asymmetric key parser 'x509' registered <6>[ 7.497914] bounce: pool size: 64 pages <6>[ 7.501829] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 7.509367] io scheduler mq-deadline registered <6>[ 7.514158] io scheduler kyber registered <4>[ 7.519304] test_firmware: interface ready <6>[ 7.711244] mxs-dma 110000.dma-apbh: initialized <4>[ 7.781234] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.788518] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 8.038718] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 8.063824] SuperH (H)SCI(F) driver initialized <6>[ 8.068783] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 8.080249] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 8.086835] printk: console [ttymxc1] enabled <6>[ 8.086835] printk: console [ttymxc1] enabled <6>[ 8.095607] printk: bootconsole [ec_imx21] disabled <6>[ 8.095607] printk: bootconsole [ec_imx21] disabled <6>[ 8.112700] msm_serial: driver initialized <6>[ 8.118205] STMicroelectronics ASC driver initialized <6>[ 8.130492] STM32 USART driver initialized <6>[ 8.159308] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 8.182783] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.191540] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.199681] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.255943] brd: module loaded <6>[ 8.319362] loop: module loaded <6>[ 8.326285] lkdtm: No crash points registered, enable through debugfs <6>[ 8.349578] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 8.357894] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 8.366272] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 8.374810] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 8.383138] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 8.391744] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 8.399763] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 8.411525] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 8.418818] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 8.427983] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 8.442820] scsi host0: ahci-imx <6>[ 8.448773] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 8.517360] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 8.531525] pps pps0: new PPS source ptp0 <6>[ 8.594706] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 8.605875] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 8.611140] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 8.617669] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 8.623421] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 8.652958] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 8.660812] usbcore: registered new interface driver pegasus <6>[ 8.667041] usbcore: registered new interface driver asix <6>[ 8.672954] usbcore: registered new interface driver ax88179_178a <6>[ 8.679493] usbcore: registered new interface driver cdc_ether <6>[ 8.685893] usbcore: registered new interface driver smsc75xx <6>[ 8.692225] usbcore: registered new interface driver smsc95xx <6>[ 8.698413] usbcore: registered new interface driver net1080 <6>[ 8.704572] usbcore: registered new interface driver cdc_subset <6>[ 8.710930] usbcore: registered new interface driver zaurus <6>[ 8.717108] usbcore: registered new interface driver cdc_ncm <6>[ 8.736804] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 8.743771] ehci-pci: EHCI PCI platform driver <6>[ 8.748672] ehci-platform: EHCI generic platform driver <6>[ 8.755347] ehci-orion: EHCI orion driver <6>[ 8.760629] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.765916] ehci-st: EHCI STMicroelectronics driver <6>[ 8.772067] ehci-exynos: EHCI Exynos driver <6>[ 8.777446] ehci-atmel: EHCI Atmel driver <6>[ 8.782704] tegra-ehci: Tegra EHCI driver <6>[ 8.784317] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.787978] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.793090] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.799304] ohci-pci: OHCI PCI platform driver <6>[ 8.805826] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.810703] ohci-platform: OHCI generic platform driver <6>[ 8.824659] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.829913] ohci-st: OHCI STMicroelectronics driver <6>[ 8.836112] ohci-atmel: OHCI Atmel driver <6>[ 8.844183] usbcore: registered new interface driver usb-storage <6>[ 8.885460] i2c /dev entries driver <6>[ 8.977793] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.984336] sdhci: Copyright(c) Pierre Ossman <6>[ 8.999233] Synopsys Designware Multimedia Card Interface Driver <6>[ 9.013545] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 9.023423] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 9.023430] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 9.034239] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 9.041704] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 9.052103] usbcore: registered new interface driver usbhid <6>[ 9.057979] usbhid: USB HID core driver <6>[ 9.062582] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 9.075692] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 9.089088] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 9.097559] IPv4 over IPsec tunneling driver <6>[ 9.107467] NET: Registered protocol family 10 <6>[ 9.118227] Segment Routing with IPv6 <6>[ 9.126765] mmc2: new high speed SDHC card at address e624 <6>[ 9.128914] NET: Registered protocol family 17 <6>[ 9.136800] mmcblk2: mmc2:e624 SL16G 14.8 GiB <5>[ 9.139651] Key type dns_resolver registered <4>[ 9.160397] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 9.163560] ThumbEE CPU extension supported. <4>[ 9.168464] GPT:29296874 != 31116287 <5>[ 9.172889] Registering SWP/SWPB emulation handler <4>[ 9.176697] GPT:Alternate GPT header not at the end of the disk. <5>[ 9.183119] Loading compiled-in X.509 certificates <4>[ 9.188108] GPT:29296874 != 31116287 <4>[ 9.197083] GPT: Use GNU Parted to correct GPT errors. <6>[ 9.202659] mmcblk2: p1 p2 p3 <4>[ 9.377663] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.386399] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.400336] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.443834] imx_usb 2184200.usb: No over current polarity defined <6>[ 9.460520] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 9.466140] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.501998] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 9.523546] hub 1-0:1.0: USB hub found <6>[ 9.530121] hub 1-0:1.0: 1 port detected <6>[ 9.547357] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 9.580758] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.589390] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.603508] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.635612] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.644197] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.658016] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.677889] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 9.708760] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.717358] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.731435] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.753202] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 9.941893] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 10.150981] hub 1-1:1.0: USB hub found <6>[ 10.155937] hub 1-1:1.0: 3 ports detected <4>[ 10.187775] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 10.196422] panel-simple panel-lcd: Specify missing connector_type <4>[ 10.210483] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 12.883307] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 12.911890] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 12.941460] Sending DHCP requests ., OK <6>[ 12.986316] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 12.994830] IP-Config: Complete: <6>[ 12.998410] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 13.009207] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 13.017366] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 13.017384] nameserver0=192.168.201.1 <6>[ 13.080946] Freeing unused kernel memory: 2048K <6>[ 13.104199] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 13.533829] udevd[139]: starting version 3.2.9 <5>[ 13.542426] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.550184] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.557152] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 13.577602] udevd[139]: specified user 'tss' unknown <27>[ 13.583259] udevd[139]: specified group 'tss' unknown <30>[ 13.597174] udevd[140]: starting eudev-3.2.9 <6>[ 15.003605] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 15.071135] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.080020] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.092991] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 15.167085] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.238342] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.261963] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.270987] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.280177] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.310526] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.319390] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.428442] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.446089] CAN device driver interface <6>[ 15.743414] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.753073] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.791636] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.798488] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 15.817021] caam 2100000.crypto: Entropy delay = 3200 <6>[ 15.883308] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 15.912246] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 15.918820] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 15.925369] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 15.944069] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.949529] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 15.956515] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 15.982848] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <6>[ 16.113532] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.122529] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.131376] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.140105] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.257619] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.266538] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.303961] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 16.305132] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 16.327934] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 16.343750] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 16.364654] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.364680] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 16.373464] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.382442] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 16.390472] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.404280] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.422005] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 16.431965] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 16.432937] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.462627] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.522696] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.531688] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.540431] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.549217] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.569249] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.578920] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.610640] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.653595] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.662608] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.671681] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.680485] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.365966] caam algorithms registered in /proc/crypto <6>[ 17.376750] caam 2100000.crypto: registering rng-caam <4>[ 17.389735] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.398714] panel-simple panel-lcd: Specify missing connector_type <4>[ 17.420025] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 17.457930] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.466801] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.475689] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.484469] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 17.499985] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.509040] panel-simple panel-lcd: Specify missing connector_type done Saving random seed: <5>[ 17.566054] random: crng init done <5>[ 17.569771] random: 1 urandom warning(s) missed due to ratelimiting OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9334774/environment . /lava-9334774/environment / # /lava-9334774/bin/lava-test-runner /lava-9334774/0 /lava-9334774/bin/lava-test-runner /lava-9334774/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-9334774/0/tests/0_dmesg + cat uuid + UUID=9334774_1.5.2.4.1<8>[ 18.728905] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 18.868459] <8>[ 18.993805] <8>[ 19.118909] + set +x <8>[ 19.131971] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9334774/environment / # . /lava-9334774/environment/lava-9334774/bin/lava-test-runner /lava-9334774/1 / # /lava-9334774/bin/lava-test-runner /lava-9334774/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-9334774/1/tests/1_bootrr + cat uuid + UUID=9334774_1.5.2.4.5<8>[ 19.810071] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9334774/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds 120000.hdmi panel-lcd /lava-9334774/1/../bin/lava-test-case <8>[ 21.032465] /lava-9334774/1/../bin/lava-test-case <8>[ 21.156671] /lava-9334774/1/../bin/lava-test-case <8>[ 21.226573] + set +x <8>[ 21.277228] / #