[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9334783/tftp-deploy-qcfjfrt6/kernel/zImage tftp 0x10000000 9334783/tftp-deploy-qcfjfrt6/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9334783/tftp-deploy-qcfjfrt6/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 11.2 MiB/s done Bytes transferred = 12345856 (bc6200 hex) => tftp 0x14000000 9334783/tftp-deploy-qcfjfrt6/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9334783/tftp-deploy-qcfjfrt6/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9334783/tftp-deploy-qcfjfrt6/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 11.1 MiB/s done Bytes transferred = 15457037 (ebdb0d hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9334783/tftp-deploy-qcfjfrt6/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9334783/tftp-deploy-qcfjfrt6/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '9334783/tftp-deploy-qcfjfrt6/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.5 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334783/extract-nfsrootfs-jxxnzvjk,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334783/extract-nfsrootfs-jxxnzvjk,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbc6200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15456973 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.170-cip27 (KernelCI@build-j1107502-arm-gcc-10-multi-v7-defconfig-kselftest-pvq6c) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Feb 25 18:26:27 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334783/extract-nfsrootfs-jxxnzvjk,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 921428K/1048576K available (17408K kernel code, 2651K rwdata, 8100K rodata, 2048K init, 6691K bss, 61612K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 55428 entries in 163 pages <6>[ 0.000000] ftrace: allocated 163 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022823] Console: colour dummy device 80x30 <4>[ 0.024729] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032738] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037082] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041493] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046128] ... CLASSHASH_SIZE: 4096 <4>[ 0.050715] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055437] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060111] ... CHAINHASH_SIZE: 32768 <4>[ 0.064808] memory used by lock dependency info: 4061 kB <4>[ 0.070489] memory used for stack traces: 2112 kB <4>[ 0.075534] per task-struct memory footprint: 1536 bytes <6>[ 0.081220] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091639] pid_max: default: 32768 minimum: 301 <6>[ 0.096868] LSM: Security Framework initializing <6>[ 0.101431] LSM support for eBPF active <6>[ 0.105590] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.113029] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123644] CPU: Testing write buffer coherency: ok <6>[ 0.126189] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.132437] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141353] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147819] rcu: Hierarchical SRCU implementation. <6>[ 0.159737] EFI services will not be available. <6>[ 0.163007] smp: Bringing up secondary CPUs ... <6>[ 0.169820] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.169836] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.182272] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.182287] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.194381] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.194396] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.203624] smp: Brought up 1 node, 4 CPUs <6>[ 0.207268] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.213584] CPU: All CPU(s) started in SVC mode. <6>[ 0.221239] devtmpfs: initialized <6>[ 0.278658] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.286532] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.293962] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.306062] pinctrl core: initialized pinctrl subsystem <6>[ 0.315829] DMI not present or invalid. <6>[ 0.319395] NET: Registered protocol family 16 <6>[ 0.333574] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.347709] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.348275] cpuidle: using governor menu <6>[ 0.356461] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 1.114647] vdd1p1: supplied by regulator-dummy <6>[ 1.149025] vdd3p0: supplied by regulator-dummy <6>[ 1.182637] vdd2p5: supplied by regulator-dummy <6>[ 1.216344] vddarm: supplied by regulator-dummy <6>[ 1.250962] vddpu: supplied by regulator-dummy <6>[ 1.283531] vddsoc: supplied by regulator-dummy <6>[ 2.630317] No ATAGs? <6>[ 2.631259] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.638376] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.664484] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.699414] Serial: AMBA PL011 UART driver <6>[ 2.765818] Kprobes globally optimized <6>[ 2.889067] iommu: Default domain type: Translated <6>[ 2.893884] vgaarb: loaded <5>[ 2.899278] SCSI subsystem initialized <6>[ 2.903091] usbcore: registered new interface driver usbfs <6>[ 2.906566] usbcore: registered new interface driver hub <6>[ 2.911972] usbcore: registered new device driver usb <6>[ 2.924945] i2c i2c-0: IMX I2C adapter registered <6>[ 2.934389] i2c i2c-1: IMX I2C adapter registered <6>[ 2.941153] i2c i2c-2: IMX I2C adapter registered <6>[ 2.948070] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.950475] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.960000] PTP clock support registered <6>[ 2.984295] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.688726] NET: Registered protocol family 2 <6>[ 4.691279] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.701649] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.707776] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.715801] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.724699] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.730657] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.737686] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.744456] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.752190] NET: Registered protocol family 1 <6>[ 4.758923] RPC: Registered named UNIX socket transport module. <6>[ 4.762331] RPC: Registered udp transport module. <6>[ 4.767428] RPC: Registered tcp transport module. <6>[ 4.772239] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.779050] NET: Registered protocol family 44 <6>[ 4.783667] PCI: CLS 0 bytes, default 64 <6>[ 4.790460] Trying to unpack rootfs image as initramfs... <6>[ 6.702687] Freeing initrd memory: 15096K <4>[ 6.705283] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.713319] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.729402] Initialise system trusted keyrings <6>[ 6.732322] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.790035] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.797190] NFS: Registering the id_resolver key type <5>[ 6.799814] Key type id_resolver registered <5>[ 6.804220] Key type id_legacy registered <6>[ 6.809006] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.815484] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.823187] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.829842] Key type asymmetric registered <5>[ 6.832047] Asymmetric key parser 'x509' registered <6>[ 6.837540] bounce: pool size: 64 pages <6>[ 6.841312] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.848965] io scheduler mq-deadline registered <6>[ 6.853627] io scheduler kyber registered <4>[ 6.858920] test_firmware: interface ready <6>[ 7.050494] mxs-dma 110000.dma-apbh: initialized <4>[ 7.120551] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.127802] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 7.378092] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.403151] SuperH (H)SCI(F) driver initialized <6>[ 7.408262] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.419712] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.426274] printk: console [ttymxc1] enabled <6>[ 7.426274] printk: console [ttymxc1] enabled <6>[ 7.435068] printk: bootconsole [ec_imx21] disabled <6>[ 7.435068] printk: bootconsole [ec_imx21] disabled <6>[ 7.452035] msm_serial: driver initialized <6>[ 7.457654] STMicroelectronics ASC driver initialized <6>[ 7.469950] STM32 USART driver initialized <6>[ 7.498477] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.521851] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.530612] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.538802] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.594788] brd: module loaded <6>[ 7.658004] loop: module loaded <6>[ 7.664922] lkdtm: No crash points registered, enable through debugfs <6>[ 7.688277] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.696584] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.704956] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.713437] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.721766] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.730390] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.738492] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.750164] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.757558] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.766718] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.781470] scsi host0: ahci-imx <6>[ 7.787486] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.855944] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.870045] pps pps0: new PPS source ptp0 <6>[ 7.917336] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.928537] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.933861] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.940333] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.946084] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.975699] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.983556] usbcore: registered new interface driver pegasus <6>[ 7.989798] usbcore: registered new interface driver asix <6>[ 7.995696] usbcore: registered new interface driver ax88179_178a <6>[ 8.002231] usbcore: registered new interface driver cdc_ether <6>[ 8.008639] usbcore: registered new interface driver smsc75xx <6>[ 8.014970] usbcore: registered new interface driver smsc95xx <6>[ 8.021164] usbcore: registered new interface driver net1080 <6>[ 8.027326] usbcore: registered new interface driver cdc_subset <6>[ 8.033683] usbcore: registered new interface driver zaurus <6>[ 8.039861] usbcore: registered new interface driver cdc_ncm <6>[ 8.059546] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 8.066516] ehci-pci: EHCI PCI platform driver <6>[ 8.071421] ehci-platform: EHCI generic platform driver <6>[ 8.078079] ehci-orion: EHCI orion driver <6>[ 8.083376] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.088669] ehci-st: EHCI STMicroelectronics driver <6>[ 8.094862] ehci-exynos: EHCI Exynos driver <6>[ 8.100250] ehci-atmel: EHCI Atmel driver <6>[ 8.105521] tegra-ehci: Tegra EHCI driver <6>[ 8.110779] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.117383] ohci-pci: OHCI PCI platform driver <6>[ 8.122289] ohci-platform: OHCI generic platform driver <6>[ 8.126753] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.128886] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.133990] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.138844] ohci-st: OHCI STMicroelectronics driver <6>[ 8.144407] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.150525] ohci-atmel: OHCI Atmel driver <6>[ 8.165200] usbcore: registered new interface driver usb-storage <6>[ 8.206400] i2c /dev entries driver <6>[ 8.298936] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.305481] sdhci: Copyright(c) Pierre Ossman <6>[ 8.320428] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.334809] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.344729] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.344736] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.355544] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.362848] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.373235] usbcore: registered new interface driver usbhid <6>[ 8.379165] usbhid: USB HID core driver <6>[ 8.384141] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.396890] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.410292] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.418757] IPv4 over IPsec tunneling driver <6>[ 8.428612] NET: Registered protocol family 10 <6>[ 8.439340] Segment Routing with IPv6 <6>[ 8.447379] mmc2: new high speed SDHC card at address aaaa <6>[ 8.450083] NET: Registered protocol family 17 <6>[ 8.457440] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <5>[ 8.460290] Key type dns_resolver registered <4>[ 8.481008] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 8.483416] ThumbEE CPU extension supported. <4>[ 8.488901] GPT:29296874 != 31116287 <5>[ 8.493463] Registering SWP/SWPB emulation handler <4>[ 8.497333] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.497352] GPT:29296874 != 31116287 <5>[ 8.504603] Loading compiled-in X.509 certificates <4>[ 8.508941] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.523307] mmcblk2: p1 p2 p3 <4>[ 8.696769] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.705563] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.719410] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.761289] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.778095] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.783593] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.814414] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.835835] hub 1-0:1.0: USB hub found <6>[ 8.842458] hub 1-0:1.0: 1 port detected <6>[ 8.859646] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.892997] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.901693] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.915654] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.947935] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.956536] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.970392] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.989999] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 9.020109] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.028796] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.042789] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.065661] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 9.244323] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.453475] hub 1-1:1.0: USB hub found <6>[ 9.459643] hub 1-1:1.0: 3 ports detected <4>[ 9.496965] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.505766] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.522065] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 12.165880] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 12.195332] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 12.223895] Sending DHCP requests ., OK <6>[ 12.268723] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 12.277278] IP-Config: Complete: <6>[ 12.280860] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 12.291838] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 12.300136] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 12.300183] nameserver0=192.168.201.1 <6>[ 12.372842] Freeing unused kernel memory: 2048K <6>[ 12.384725] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 16.501059] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 16.549194] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 16.560590] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.590169] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.604698] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.635932] CAN device driver interface <4>[ 16.654291] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.665776] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.680077] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.738705] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 16.747945] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 16.766549] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 16.773439] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 16.792024] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 16.800877] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 16.807422] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 16.817975] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <4>[ 16.832178] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.844464] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.846062] caam 2100000.crypto: Entropy delay = 3200 <4>[ 16.874094] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.886034] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.895108] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.904332] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.913390] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.917227] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 16.936618] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.945388] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.977989] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 16.983458] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 16.990425] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 17.025365] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 17.052682] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 17.073324] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 17.078867] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.082489] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 17.086898] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 17.090794] panel-simple panel-lcd: Specify missing connector_type <6>[ 17.092889] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 17.098321] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 17.141449] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.150726] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.159858] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.168696] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 17.186899] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 17.226255] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.234953] panel-simple panel-lcd: Specify missing connector_type <6>[ 17.266713] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.275952] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.285109] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.294062] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 17.980704] caam algorithms registered in /proc/crypto <6>[ 18.000127] caam 2100000.crypto: registering rng-caam <5>[ 18.129402] random: crng init done <4>[ 18.139678] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 18.174859] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 18.183487] panel-simple panel-lcd: Specify missing connector_type <6>[ 18.203387] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.212275] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.221142] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.229869] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:1c mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.36 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-6 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 20.480356] systemd[1]: System time before build time, advancing clock. <30>[ 20.787953] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 20.815959] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 20.883283] systemd[1]: Set hostname to . <30>[ 22.670318] systemd[1]: Queued start job for default target Graphical Interface. <30>[ 22.685126] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 22.704831] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 22.749014] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 22.798348] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 22.848560] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 22.897854] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 22.945601] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 22.958258] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 22.994673] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 23.035020] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 23.074897] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 23.116138] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 23.159369] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 23.265950] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 23.280428] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 23.331147] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 23.381467] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 23.436589] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 23.489545] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 23.538386] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 23.549869] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 23.573547] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 23.628483] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 23.679099] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 23.745489] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 23.807338] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 23.835091] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 23.883433] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <6>[ 23.913624] fuse: init (API version 7.32) <30>[ 23.917728] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 23.990540] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 24.038553] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 24.107583] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 24.160359] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 24.207665] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 24.272205] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 24.384074] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 24.394944] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 24.449914] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 24.460054] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 24.520457] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 24.530844] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 24.589668] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 24.635892] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Remount Root and Kernel File Systems. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 24.999075] systemd-journald[271]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Found device /dev/ttymxc1. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.170-cip27 #1 SMP Sat Feb 25 18:26:27 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9334783/extract-nfsrootfs-jxxnzvjk' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9334783/extract-nfsrootfs-jxxnzvjk' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9334783/environment . /lava-9334783/environment / # /lava-9334783/bin/lava-test-runner /lava-9334783/0 /lava-9334783/bin/lava-test-runner /lava-9334783/0 + export TESTRUN_ID=0_dmesg + cd /lava-9334783/0/tests/0_dmesg + cat uuid + UUID=9334783_1.6.2.4.1<8>[ 44.685849] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 44.955529] <8>[ 45.160960] <8>[ 45.369606] + set +x <8>[ 45.381947] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9334783/environment / # . /lava-9334783/environment/lava-9334783/bin/lava-test-runner /lava-9334783/1 / # /lava-9334783/bin/lava-test-runner /lava-9334783/1 + export TESTRUN_ID=1_bootrr + cd /lava-9334783/1/tests/1_bootrr + cat uuid + UUID=9334783_1.6.2.4.5<8>[ 46.218850] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9334783/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd 120000.hdmi /lava-9334783/1/../bin/lava-test-case <8>[ 47.575511] /lava-9334783/1/../bin/lava-test-case <8>[ 47.787686] /lava-9334783/1/../bin/lava-test-case <8>[ 47.895898] + set +x <8>[ 47.972948] / #