[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9334779/tftp-deploy-fnuxyyl0/kernel/zImage tftp 0x10000000 9334779/tftp-deploy-fnuxyyl0/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '9334779/tftp-deploy-fnuxyyl0/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################# 11.3 MiB/s done Bytes transferred = 12345856 (bc6200 hex) => tftp 0x14000000 9334779/tftp-deploy-fnuxyyl0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9334779/tftp-deploy-fnuxyyl0/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '9334779/tftp-deploy-fnuxyyl0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 5.3 MiB/s done Bytes transferred = 15455362 (ebd482 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9334779/tftp-deploy-fnuxyyl0/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9334779/tftp-deploy-fnuxyyl0/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '9334779/tftp-deploy-fnuxyyl0/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334779/extract-nfsrootfs-f3k4q_yd,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334779/extract-nfsrootfs-f3k4q_yd,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbc6200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15455298 Bytes = 14.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.170-cip27 (KernelCI@build-j1107502-arm-gcc-10-multi-v7-defconfig-kselftest-pvq6c) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Feb 25 18:26:27 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9334779/extract-nfsrootfs-f3k4q_yd,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 921428K/1048576K available (17408K kernel code, 2651K rwdata, 8100K rodata, 2048K init, 6691K bss, 61612K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 55428 entries in 163 pages [ 0.000000] ftrace: allocated 163 pages with 4 groups [ 0.000000] Running RCU self tests [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000010] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000043] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004449] Console: colour dummy device 80x30 [ 0.004516] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.004546] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.004573] ... MAX_LOCK_DEPTH: 48 [ 0.004601] ... MAX_LOCKDEP_KEYS: 8192 [ 0.004628] ... CLASSHASH_SIZE: 4096 [ 0.004655] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.004681] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.004707] ... CHAINHASH_SIZE: 32768 [ 0.004734] memory used by lock dependency info: 4061 kB [ 0.004761] memory used for stack traces: 2112 kB [ 0.004789] per task-struct memory footprint: 1536 bytes [ 0.004891] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004946] pid_max: default: 32768 minimum: 301 [ 0.005332] LSM: Security Framework initializing [ 0.005446] LSM support for eBPF active [ 0.005594] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005648] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.008261] CPU: Testing write buffer coherency: ok [ 0.008395] CPU0: Spectre v2: using BPIALL workaround [ 0.009515] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.013504] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.015972] rcu: Hierarchical SRCU implementation. [ 0.025379] EFI services will not be available. [ 0.026724] smp: Bringing up secondary CPUs ... [ 0.030107] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.030122] CPU1: Spectre v2: using BPIALL workaround [ 0.034205] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.034220] CPU2: Spectre v2: using BPIALL workaround [ 0.037917] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.037932] CPU3: Spectre v2: using BPIALL workaround [ 0.038806] smp: Brought up 1 node, 4 CPUs [ 0.038851] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.039041] CPU: All CPU(s) started in SVC mode. [ 0.041815] devtmpfs: initialized [ 0.098576] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.101626] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.101708] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.106596] pinctrl core: initialized pinctrl subsystem [ 0.113822] DMI not present or invalid. [ 0.116168] NET: Registered protocol family 16 [ 0.127965] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.137798] thermal_sys: Registered thermal governor 'step_wise' [ 0.138358] cpuidle: using governor menu [ 0.138970] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.892533] vdd1p1: supplied by regulator-dummy [ 0.924617] vdd3p0: supplied by regulator-dummy [ 0.956347] vdd2p5: supplied by regulator-dummy [ 0.988038] vddarm: supplied by regulator-dummy [ 1.020724] vddpu: supplied by regulator-dummy [ 1.051452] vddsoc: supplied by regulator-dummy [ 2.396863] No ATAGs? [ 2.397926] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 2.398015] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 2.418209] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 2.449023] Serial: AMBA PL011 UART driver [ 2.513736] Kprobes globally optimized [ 2.635573] iommu: Default domain type: Translated [ 2.637751] vgaarb: loaded [ 2.642753] SCSI subsystem initialized [ 2.644935] usbcore: registered new interface driver usbfs [ 2.645262] usbcore: registered new interface driver hub [ 2.645500] usbcore: registered new device driver usb [ 2.653422] i2c i2c-0: IMX I2C adapter registered [ 2.660574] i2c i2c-1: IMX I2C adapter registered [ 2.665165] i2c i2c-2: IMX I2C adapter registered [ 2.670198] pps_core: LinuxPPS API ver. 1 registered [ 2.670242] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.670345] PTP clock support registered [ 2.688549] clocksource: Switched to clocksource mxc_timer1 [ 4.393469] NET: Registered protocol family 2 [ 4.394265] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 4.397593] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) [ 4.397780] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 4.398017] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) [ 4.399566] TCP: Hash tables configured (established 8192 bind 8192) [ 4.400647] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) [ 4.400992] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) [ 4.401253] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) [ 4.402013] NET: Registered protocol family 1 [ 4.405000] RPC: Registered named UNIX socket transport module. [ 4.405093] RPC: Registered udp transport module. [ 4.405134] RPC: Registered tcp transport module. [ 4.405176] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.405240] NET: Registered protocol family 44 [ 4.405312] PCI: CLS 0 bytes, default 64 [ 4.407832] Trying to unpack rootfs image as initramfs... [ 6.318113] Freeing initrd memory: 15096K [ 6.319205] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 6.320856] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 6.330316] Initialise system trusted keyrings [ 6.331352] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 6.383284] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 6.387104] NFS: Registering the id_resolver key type [ 6.387328] Key type id_resolver registered [ 6.387424] Key type id_legacy registered [ 6.388077] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 6.388272] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 6.388498] ntfs: driver 2.1.32 [Flags: R/O]. [ 6.390734] Key type asymmetric registered [ 6.390865] Asymmetric key parser 'x509' registered [ 6.391311] bounce: pool size: 64 pages [ 6.391490] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 6.391602] io scheduler mq-deadline registered [ 6.391653] io scheduler kyber registered [ 6.392658] test_firmware: interface ready [ 6.581277] mxs-dma 110000.dma-apbh: initialized [ 6.649505] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 6.649760] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 6.906893] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 6.928349] SuperH (H)SCI(F) driver initialized [ 6.931442] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 6.936724] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 7.869017] printk: console [ttymxc1] enabled [ 7.880080] msm_serial: driver initialized [ 7.885347] STMicroelectronics ASC driver initialized [ 7.897383] STM32 USART driver initialized [ 7.925332] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 [ 7.948481] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.956938] panel-simple panel-lcd: Specify missing connector_type [ 7.964872] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.020326] brd: module loaded [ 8.083700] loop: module loaded [ 8.090384] lkdtm: No crash points registered, enable through debugfs [ 8.113429] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 8.121477] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 8.129581] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 8.137805] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 8.145892] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 8.154189] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 8.162023] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 8.173445] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 8.180575] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 8.189470] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 8.204054] scsi host0: ahci-imx [ 8.209819] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 8.277998] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 8.291857] pps pps0: new PPS source ptp0 [ 8.338673] fec 2188000.ethernet eth0: registered PHC device 0 [ 8.349725] e1000e: Intel(R) PRO/1000 Network Driver [ 8.354732] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 8.360996] igb: Intel(R) Gigabit Ethernet Network Driver [ 8.366431] igb: Copyright (c) 2007-2014 Intel Corporation. [ 8.395581] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 8.403260] usbcore: registered new interface driver pegasus [ 8.409227] usbcore: registered new interface driver asix [ 8.414815] usbcore: registered new interface driver ax88179_178a [ 8.421151] usbcore: registered new interface driver cdc_ether [ 8.427257] usbcore: registered new interface driver smsc75xx [ 8.433329] usbcore: registered new interface driver smsc95xx [ 8.439332] usbcore: registered new interface driver net1080 [ 8.445180] usbcore: registered new interface driver cdc_subset [ 8.451368] usbcore: registered new interface driver zaurus [ 8.457229] usbcore: registered new interface driver cdc_ncm [ 8.476628] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 8.483337] ehci-pci: EHCI PCI platform driver [ 8.487994] ehci-platform: EHCI generic platform driver [ 8.494383] ehci-orion: EHCI orion driver [ 8.499453] SPEAr-ehci: EHCI SPEAr driver [ 8.504440] ehci-st: EHCI STMicroelectronics driver [ 8.510335] ehci-exynos: EHCI Exynos driver [ 8.515461] ehci-atmel: EHCI Atmel driver [ 8.520463] tegra-ehci: Tegra EHCI driver [ 8.525456] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.531817] ohci-pci: OHCI PCI platform driver [ 8.536461] ohci-platform: OHCI generic platform driver [ 8.542782] SPEAr-ohci: OHCI SPEAr driver [ 8.547747] ohci-st: OHCI STMicroelectronics driver [ 8.551366] ata1: SATA link down (SStatus 0 SControl 300) [ 8.553660] ohci-atmel: OHCI Atmel driver [ 8.558486] ahci-imx 2200000.sata: no device found, disabling link. [ 8.565938] usbcore: registered new interface driver usb-storage [ 8.568472] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 8.616609] i2c /dev entries driver [ 8.708654] sdhci: Secure Digital Host Controller Interface driver [ 8.714879] sdhci: Copyright(c) Pierre Ossman [ 8.729614] Synopsys Designware Multimedia Card Interface Driver [ 8.743657] sdhci-pltfm: SDHCI platform and OF driver helper [ 8.753257] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 8.753263] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 8.763657] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 8.770794] ledtrig-cpu: registered to indicate activity on CPUs [ 8.780962] usbcore: registered new interface driver usbhid [ 8.786575] usbhid: USB HID core driver [ 8.792888] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 8.804877] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 8.817951] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 8.826250] IPv4 over IPsec tunneling driver [ 8.835960] NET: Registered protocol family 10 [ 8.846497] Segment Routing with IPv6 [ 8.854948] mmc2: new high speed SDHC card at address aaaa [ 8.856852] NET: Registered protocol family 17 [ 8.864689] mmcblk2: mmc2:aaaa SL16G 14.8 GiB [ 8.867302] Key type dns_resolver registered [ 8.887907] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 8.890287] ThumbEE CPU extension supported. [ 8.895550] GPT:29296874 != 31116287 [ 8.899831] Registering SWP/SWPB emulation handler [ 8.903377] GPT:Alternate GPT header not at the end of the disk. [ 8.914377] GPT:29296874 != 31116287 [ 8.916032] Loading compiled-in X.509 certificates [ 8.918016] GPT: Use GNU Parted to correct GPT errors. [ 8.918292] mmcblk2: p1 p2 p3 [ 9.112327] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.120817] panel-simple panel-lcd: Specify missing connector_type [ 9.134414] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.175424] imx_usb 2184200.usb: No over current polarity defined [ 9.189954] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 9.195167] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 9.228853] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 9.250093] hub 1-0:1.0: USB hub found [ 9.256446] hub 1-0:1.0: 1 port detected [ 9.273433] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 9.306491] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.314865] panel-simple panel-lcd: Specify missing connector_type [ 9.328532] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.360217] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.368543] panel-simple panel-lcd: Specify missing connector_type [ 9.382119] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.401473] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 9.431755] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.440088] panel-simple panel-lcd: Specify missing connector_type [ 9.453685] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.475302] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 9.658773] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 9.868112] hub 1-1:1.0: USB hub found [ 9.872858] hub 1-1:1.0: 3 ports detected [ 9.904190] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.912552] panel-simple panel-lcd: Specify missing connector_type [ 9.926416] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 12.650348] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 12.678961] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.708540] Sending DHCP requests ., OK [ 12.752732] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 [ 12.761017] IP-Config: Complete: [ 12.764335] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 [ 12.775009] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) [ 12.783044] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 12.783091] nameserver0=192.168.201.1 [ 12.855480] Freeing unused kernel memory: 2048K [ 12.920357] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 16.936077] imx-ipuv3 2400000.ipu: IPUv3H probed [ 16.967331] panel-simple panel-lcd: supply power not found, using dummy regulator [ 16.980283] panel-simple panel-lcd: Specify missing connector_type [ 16.998755] imx-ipuv3 2800000.ipu: IPUv3H probed [ 17.013653] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.046886] CAN device driver interface [ 17.078693] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.087035] panel-simple panel-lcd: Specify missing connector_type [ 17.107155] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.189732] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.198233] panel-simple panel-lcd: Specify missing connector_type [ 17.224071] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 17.232874] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 17.243155] caam 2100000.crypto: Entropy delay = 3200 [ 17.255577] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 17.262322] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 17.309112] caam 2100000.crypto: Instantiated RNG4 SH0 [ 17.369876] caam 2100000.crypto: Instantiated RNG4 SH1 [ 17.375100] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 17.381875] caam 2100000.crypto: job rings = 2, qi = 0 [ 17.403343] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 17.415688] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 17.422017] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 17.428980] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.431465] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 [ 17.457804] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.462920] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.466737] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.474773] panel-simple panel-lcd: Specify missing connector_type [ 17.482441] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 17.497311] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.529449] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.536572] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 17.555486] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 17.580737] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 17.589820] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 17.591570] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 17.598785] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 17.624027] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.633017] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.641586] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 17.650106] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.667654] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.686563] panel-simple panel-lcd: Specify missing connector_type [ 17.701859] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.740561] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.749111] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.757645] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 17.766179] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.789227] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.797595] panel-simple panel-lcd: Specify missing connector_type [ 18.327561] caam algorithms registered in /proc/crypto [ 18.351437] caam 2100000.crypto: registering rng-caam [ 18.479488] random: crng init done [ 18.485203] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 18.534097] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 18.542744] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 18.551293] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 18.559739] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 18.575303] panel-simple panel-lcd: supply power not found, using dummy regulator [ 18.583804] panel-simple panel-lcd: Specify missing connector_type [ 18.601858] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available [ 18.641306] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 18.649869] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) Device /sys/class/net/eth0 found [ 18.658612] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) done.[ 18.669378] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 20.766952] systemd[1]: System time before build time, advancing clock. [ 21.056659] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 21.083194] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 21.146563] systemd[1]: Set hostname to . [ 22.942251] systemd[1]: Queued start job for default target Graphical Interface. [ 22.958685] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 23.013590] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 23.074161] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 23.124342] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 23.174197] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 23.223354] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 23.269888] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 23.282688] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 23.321201] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 23.358829] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 23.399445] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 23.439567] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 23.483017] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 23.587858] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 23.602949] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 23.645143] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 23.695817] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 23.750981] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 23.804004] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 23.853106] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 23.864284] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 23.887359] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 23.941013] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 24.023991] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 24.079808] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 24.130979] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 24.178839] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 24.247456] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 24.254770] fuse: init (API version 7.32) [ 24.283730] systemd[1]: Starting Journal Service... Starting Journal Service... [ 24.348608] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 24.401544] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 24.450732] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 24.507777] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 24.561176] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 24.616948] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 24.743505] systemd[1]: modprobe@configfs.service: Succeeded. [ 24.753806] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 24.794382] systemd[1]: modprobe@drm.service: Succeeded. [ 24.804304] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 24.855077] systemd[1]: modprobe@fuse.service: Succeeded. [ 24.865075] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 24.914132] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. [ 24.964014] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. [ 25.010205] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 25.325807] systemd-journald[285]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. Starting Network Name Resolution... [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.170-cip27 #1 SMP Sat Feb 25 18:26:27 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9334779/extract-nfsrootfs-f3k4q_yd' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9334779/extract-nfsrootfs-f3k4q_yd' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-9334779/environment . /lava-9334779/environment / # /lava-9334779/bin/lava-test-runner /lava-9334779/0 /lava-9334779/bin/lava-test-runner /lava-9334779/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-9334779/0/tests/0_timesync-off ++ cat uuid + UUID=9334779_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-livepatch + TESTRUN_ID=1_kselftest-livepatch + cd /lava-9334779/0/tests/1_kselftest-livepatch ++ cat uuid + UUID=9334779_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c livepatch -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.168-cip27-86-g19cf8cd2dd993/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-9334779/0/tests/1_kselftest-livepatch/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: install_deps skipped --2023-02-25 18:43:39-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.168-cip27-86-g19cf8cd2dd993/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1408208 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 1%[ ] 19.04K 65.6KB/s kselftest.tar.xz 4%[ ] 60.53K 114KB/s kselftest.tar.xz 6%[> ] 92.57K 106KB/s kselftest.tar.xz 7%[> ] 109.54K 98.8KB/s kselftest.tar.xz 9%[> ] 129.82K 99.2KB/s kselftest.tar.xz 10%[=> ] 137.82K 89.3KB/s kselftest.tar.xz 11%[=> ] 152.45K 83.2KB/s kselftest.tar.xz 12%[=> ] 168.00K 82.6KB/s kselftest.tar.xz 13%[=> ] 179.32K 79.1KB/s kselftest.tar.xz 14%[=> ] 197.70K 80.1KB/s kselftest.tar.xz 15%[==> ] 209.01K 77.4KB/s kselftest.tar.xz 16%[==> ] 224.57K 77.4KB/s kselftest.tar.xz 17%[==> ] 241.53K 77.1KB/s eta 15s kselftest.tar.xz 19%[==> ] 261.33K 78.3KB/s eta 15s kselftest.tar.xz 20%[===> ] 279.71K 77.2KB/s eta 15s kselftest.tar.xz 21%[===> ] 298.10K 77.3KB/s eta 15s kselftest.tar.xz 22%[===> ] 312.24K 76.9KB/s eta 15s kselftest.tar.xz 24%[===> ] 336.28K 78.3KB/s eta 13s kselftest.tar.xz 25%[====> ] 354.17K 78.1KB/s eta 13s kselftest.tar.xz 27%[====> ] 373.04K 74.1KB/s eta 13s kselftest.tar.xz 28%[====> ] 394.25K 72.2KB/s eta 13s kselftest.tar.xz 30%[=====> ] 422.53K 73.7KB/s eta 12s kselftest.tar.xz 32%[=====> ] 445.16K 73.2KB/s eta 12s kselftest.tar.xz 34%[=====> ] 470.61K 77.8KB/s eta 12s kselftest.tar.xz 35%[======> ] 489.00K 78.4KB/s eta 12s kselftest.tar.xz 37%[======> ] 518.69K 83.6KB/s eta 12s kselftest.tar.xz 38%[======> ] 526.69K 82.2KB/s eta 10s kselftest.tar.xz 40%[=======> ] 558.28K 86.1KB/s eta 10s kselftest.tar.xz 41%[=======> ] 576.67K 85.7KB/s eta 10s kselftest.tar.xz 43%[=======> ] 600.22K 88.9KB/s eta 10s kselftest.tar.xz 45%[========> ] 626.16K 90.5KB/s eta 10s kselftest.tar.xz 47%[========> ] 651.13K 92.5KB/s eta 8s kselftest.tar.xz 49%[========> ] 679.89K 96.1KB/s eta 8s kselftest.tar.xz 51%[=========> ] 702.52K 97.5KB/s eta 8s kselftest.tar.xz 53%[=========> ] 733.63K 99.0KB/s eta 8s kselftest.tar.xz 56%[==========> ] 773.22K 103KB/s eta 8s kselftest.tar.xz 59%[==========> ] 815.64K 109KB/s eta 6s kselftest.tar.xz 62%[===========> ] 859.48K 114KB/s eta 6s kselftest.tar.xz 64%[===========> ] 885.86K 113KB/s eta 6s kselftest.tar.xz 67%[============> ] 925.94K 119KB/s eta 6s kselftest.tar.xz 69%[============> ] 959.88K 121KB/s eta 4s kselftest.tar.xz 72%[=============> ] 1004K 123KB/s eta 4s kselftest.tar.xz 76%[==============> ] 1.03M 128KB/s eta 4s kselftest.tar.xz 79%[==============> ] 1.07M 132KB/s eta 4s kselftest.tar.xz 82%[===============> ] 1.11M 137KB/s eta 2s kselftest.tar.xz 84%[===============> ] 1.13M 138KB/s eta 2s kselftest.tar.xz 87%[================> ] 1.17M 139KB/s eta 2s kselftest.tar.xz 90%[=================> ] 1.21M 143KB/s eta 2s kselftest.tar.xz 92%[=================> ] 1.24M 146KB/s eta 2s kselftest.tar.xz 95%[==================> ] 1.28M 149KB/s eta 1s kselftest.tar.xz 97%[==================> ] 1.32M 151KB/s eta 1s kselftest.tar.xz 100%[===================>] 1.34M 154KB/s in 12s 2023-02-25 18:43:52 (110 KB/s) - 'kselftest.tar.xz' saved [1408208/1408208] skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== livepatch:test-livepatch.sh livepatch:test-callbacks.sh livepatch:test-shadow-vars.sh livepatch:test-state.sh livepatch:test-ftrace.sh ============== Tests to run =============== livepatch:test-livepatch.sh livepatch:test-callbacks.sh livepatch:test-shadow-vars.sh livepatch:test-state.sh livepatch:test-ftrace.sh ===========End Tests to run =============== [ 69.712115] kselftest: Running tests in livepatch TAP version 13 1..5 # selftests: livepatch: test-livepatch.sh [ 70.260748] livepatch: kernel.ftrace_enabled = 1 # TE[ 70.357344] ===== TEST: basic function patching ===== ST: basic function patching ... [ 70.432559] SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 1 selftests: livepatch: test-livepatch.sh # SKIP # selftests: livepatch: test-callbacks.sh [ 70.937536] livepatch: kernel.ftrace_enabled = 1 # TEST: target module before livepatch ... [ 71.024838] ===== TEST: target module before livepatch ===== [ 71.079747] SKIP: unable to load module test_klp_callbacks_mod, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_callbacks_mod, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 2 selftests: livepatch: test-callbacks.sh # SKIP # selftests: livepatch: test-shadow-vars.sh [ 71.570409] livepatch: kernel.ftrace_enabled = 1 # [ 71.652959] ===== TEST: basic shadow variable API ===== TEST: basic shadow variable API ... [ 71.713616] SKIP: unable to load module test_klp_shadow_vars, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_shadow_vars, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 3 selftests: livepatch: test-shadow-vars.sh # SKIP # selftests: livepatch: test-state.sh [ 72.210646] livepatch: kernel.ftrace_enabled = 1 # TE[ 72.293618] ===== TEST: system state modification ===== ST: system state modification ... [ 72.350967] SKIP: unable to load module test_klp_state, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_state, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 4 selftests: livepatch: test-state.sh # SKIP # selftests: livepatch: test-ftrace.sh [ 72.841647] livepatch: kernel.ftrace_enabled = 1 # T[ 72.925449] ===== TEST: livepatch interaction with ftrace_enabled sysctl ===== EST: livepatch interaction with ftrace_enabled sysctl ... [ 72.986586] livepatch: kernel.ftrace_enabled = 0 [ 72.992284] % modprobe test_klp_livepatch [ 73.056726] modprobe: FATAL: Module test_klp_livepatch not found in directory /lib/modules/5.10.170-cip27 [ 73.120056] livepatch: kernel.ftrace_enabled = 1 [ 73.180708] SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 5 selftests: livepatch: test-ftrace.sh # SKIP livepatch_test-livepatch_sh skip livepatch_test-callbacks_sh skip livepatch_test-shadow-vars_sh skip livepatch_test-state_sh skip livepatch_test-ftrace_sh skip + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #