[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9334643/tftp-deploy-jd6typ80/kernel/zImage tftp 0x10000000 9334643/tftp-deploy-jd6typ80/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9334643/tftp-deploy-jd6typ80/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 11.8 MiB/s done Bytes transferred = 9687552 (93d200 hex) => tftp 0x14000000 9334643/tftp-deploy-jd6typ80/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9334643/tftp-deploy-jd6typ80/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9334643/tftp-deploy-jd6typ80/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 11.8 MiB/s done Bytes transferred = 16072545 (f53f61 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9334643/tftp-deploy-jd6typ80/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9334643/tftp-deploy-jd6typ80/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9334643/tftp-deploy-jd6typ80/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93d200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16072481 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.170-cip27 (KernelCI@build-j1107550-arm-gcc-10-multi-v7-defconfig-zqr5r) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Feb 25 18:08:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933692K/1048576K available (13312K kernel code, 2233K rwdata, 5348K rodata, 2048K init, 426K bss, 49348K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022229] Console: colour dummy device 80x30 <6>[ 0.024117] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034531] pid_max: default: 32768 minimum: 301 <6>[ 0.039564] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046985] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055593] CPU: Testing write buffer coherency: ok <6>[ 0.060098] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065668] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072021] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079695] rcu: Hierarchical SRCU implementation. <6>[ 0.086670] EFI services will not be available. <6>[ 0.088904] smp: Bringing up secondary CPUs ... <6>[ 0.094190] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094199] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105529] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105536] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116739] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116747] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127185] smp: Brought up 1 node, 4 CPUs <6>[ 0.131413] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137871] CPU: All CPU(s) started in SVC mode. <6>[ 0.143297] devtmpfs: initialized <6>[ 0.153608] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158952] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168821] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179037] pinctrl core: initialized pinctrl subsystem <6>[ 0.183505] DMI not present or invalid. <6>[ 0.186637] NET: Registered protocol family 16 <6>[ 0.193903] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200531] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200728] cpuidle: using governor menu <6>[ 0.208817] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.384172] vdd1p1: supplied by regulator-dummy <6>[ 0.393172] vdd3p0: supplied by regulator-dummy <6>[ 0.402139] vdd2p5: supplied by regulator-dummy <6>[ 0.411072] vddarm: supplied by regulator-dummy <6>[ 0.420138] vddpu: supplied by regulator-dummy <6>[ 0.428827] vddsoc: supplied by regulator-dummy <6>[ 0.751575] No ATAGs? <6>[ 0.751760] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.759537] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.769697] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.779924] Serial: AMBA PL011 UART driver <6>[ 0.784060] printk: console [ramoops-1] enabled <6>[ 0.786446] pstore: Registered ramoops as persistent store backend <6>[ 0.792652] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.830330] iommu: Default domain type: Translated <6>[ 0.833043] vgaarb: loaded <5>[ 0.836484] SCSI subsystem initialized <6>[ 0.840192] usbcore: registered new interface driver usbfs <6>[ 0.845373] usbcore: registered new interface driver hub <6>[ 0.850958] usbcore: registered new device driver usb <6>[ 0.857725] i2c i2c-0: IMX I2C adapter registered <6>[ 0.862488] i2c i2c-1: IMX I2C adapter registered <6>[ 0.866975] i2c i2c-2: IMX I2C adapter registered <6>[ 0.872411] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.876316] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.885722] PTP clock support registered <6>[ 0.893412] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.943266] NET: Registered protocol family 2 <6>[ 1.945510] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.953879] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.961338] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.969413] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.976874] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.983571] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.990228] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.997718] NET: Registered protocol family 1 <6>[ 2.002715] RPC: Registered named UNIX socket transport module. <6>[ 2.008321] RPC: Registered udp transport module. <6>[ 2.013244] RPC: Registered tcp transport module. <6>[ 2.018227] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.024929] PCI: CLS 0 bytes, default 64 <6>[ 2.029594] Trying to unpack rootfs image as initramfs... <6>[ 3.377085] Freeing initrd memory: 15696K <4>[ 3.378981] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.386292] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.396116] Initialise system trusted keyrings <6>[ 3.399260] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.411526] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.415556] NFS: Registering the id_resolver key type <5>[ 3.420124] Key type id_resolver registered <5>[ 3.424538] Key type id_legacy registered <6>[ 3.428877] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.435760] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.443444] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.448517] Key type asymmetric registered <5>[ 3.452359] Asymmetric key parser 'x509' registered <6>[ 3.457560] bounce: pool size: 64 pages <6>[ 3.461608] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.469256] io scheduler mq-deadline registered <6>[ 3.474036] io scheduler kyber registered <6>[ 3.517430] mxs-dma 110000.dma-apbh: initialized <4>[ 3.524205] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.531114] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.597045] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.605296] SuperH (H)SCI(F) driver initialized <6>[ 3.608227] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.617116] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.625051] printk: console [ttymxc1] enabled <6>[ 3.625051] printk: console [ttymxc1] enabled <6>[ 3.634219] printk: bootconsole [ec_imx21] disabled <6>[ 3.634219] printk: bootconsole [ec_imx21] disabled <6>[ 3.645891] msm_serial: driver initialized <6>[ 3.651907] STMicroelectronics ASC driver initialized <6>[ 3.659225] STM32 USART driver initialized <4>[ 3.674612] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.682511] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.689370] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.706049] brd: module loaded <6>[ 3.719379] loop: module loaded <6>[ 3.726758] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.734988] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.743263] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.751748] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.759767] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.767534] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.775128] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.785725] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.792981] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.802062] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.812884] scsi host0: ahci-imx <6>[ 3.816767] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.837247] CAN device driver interface <6>[ 3.842657] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.852201] pps pps0: new PPS source ptp0 <6>[ 3.889100] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.896697] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.901933] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.908203] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.913886] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.925849] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.933581] usbcore: registered new interface driver pegasus <6>[ 3.939554] usbcore: registered new interface driver asix <6>[ 3.945271] usbcore: registered new interface driver ax88179_178a <6>[ 3.951664] usbcore: registered new interface driver cdc_ether <6>[ 3.957827] usbcore: registered new interface driver smsc75xx <6>[ 3.963903] usbcore: registered new interface driver smsc95xx <6>[ 3.969947] usbcore: registered new interface driver net1080 <6>[ 3.975944] usbcore: registered new interface driver cdc_subset <6>[ 3.982162] usbcore: registered new interface driver zaurus <6>[ 3.988086] usbcore: registered new interface driver cdc_ncm <6>[ 3.997578] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.004396] ehci-pci: EHCI PCI platform driver <6>[ 4.009153] ehci-platform: EHCI generic platform driver <6>[ 4.014979] ehci-orion: EHCI orion driver <6>[ 4.019475] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.023966] ehci-st: EHCI STMicroelectronics driver <6>[ 4.029299] ehci-exynos: EHCI Exynos driver <6>[ 4.033945] ehci-atmel: EHCI Atmel driver <6>[ 4.038398] tegra-ehci: Tegra EHCI driver <6>[ 4.042888] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.049368] ohci-pci: OHCI PCI platform driver <6>[ 4.054137] ohci-platform: OHCI generic platform driver <6>[ 4.059895] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.064380] ohci-st: OHCI STMicroelectronics driver <6>[ 4.069724] ohci-atmel: OHCI Atmel driver <6>[ 4.075094] usbcore: registered new interface driver usb-storage <6>[ 4.089513] i2c /dev entries driver <6>[ 4.112815] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.119291] sdhci: Copyright(c) Pierre Ossman <6>[ 4.126624] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.134897] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.142087] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.146359] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.147388] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.158091] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.164896] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.165446] usbcore: registered new interface driver usbhid <6>[ 4.170608] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.176423] usbhid: USB HID core driver <6>[ 4.182951] NET: Registered protocol family 10 <6>[ 4.182965] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.188117] Segment Routing with IPv6 <6>[ 4.189407] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.199493] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.203257] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.224291] NET: Registered protocol family 17 <6>[ 4.229016] can: controller area network core <6>[ 4.233744] NET: Registered protocol family 29 <6>[ 4.238458] can: raw protocol <6>[ 4.241696] can: broadcast manager protocol <6>[ 4.246176] can: netlink gateway - max_hops=1 <5>[ 4.251236] Key type dns_resolver registered <6>[ 4.257875] ThumbEE CPU extension supported. <5>[ 4.262427] Registering SWP/SWPB emulation handler <5>[ 4.268169] Loading compiled-in X.509 certificates <6>[ 4.278657] pstore: Using crash dump compression: deflate <4>[ 4.306560] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.314503] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.322528] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.341427] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.352189] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.357490] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.368781] mmc2: new high speed SDHC card at address 59b4 <6>[ 4.375325] mmcblk2: mmc2:59b4 SD 14.7 GiB <4>[ 4.387849] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 4.393409] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <4>[ 4.395543] GPT:7812499 != 30863359 <4>[ 4.404963] GPT:Alternate GPT header not at the end of the disk. <6>[ 4.405396] hub 1-0:1.0: USB hub found <4>[ 4.411237] GPT:7812499 != 30863359 <4>[ 4.411245] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.415318] hub 1-0:1.0: 1 port detected <6>[ 4.419066] mmcblk2: p1 p2 p3 <6>[ 4.428901] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.447395] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.455304] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.463196] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.475389] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.483255] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.491125] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.501135] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.512717] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.520661] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.528595] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.542709] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.753439] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.955133] hub 1-1:1.0: USB hub found <6>[ 4.959355] hub 1-1:1.0: 3 ports detected <4>[ 4.973913] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.982004] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.991853] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.683885] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.693484] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.723392] Sending DHCP requests ., OK <6>[ 7.767607] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 7.775950] IP-Config: Complete: <6>[ 7.779469] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.790212] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 7.798351] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.798364] nameserver0=192.168.201.1 <6>[ 7.817418] Freeing unused kernel memory: 2048K <6>[ 7.854420] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.989815] udevd[132]: starting version 3.2.9 <5>[ 7.996181] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.003134] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.010000] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.024338] udevd[132]: specified user 'tss' unknown <27>[ 8.029767] udevd[132]: specified group 'tss' unknown <30>[ 8.037502] udevd[133]: starting eudev-3.2.9 <6>[ 8.394094] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.401186] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.411306] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.419320] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.445428] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.480094] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.488100] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.521395] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.526903] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.535513] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.544119] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.552662] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.564335] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.577322] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.585266] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.587587] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.603152] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.617103] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.625076] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.648352] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.653798] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.660683] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.682232] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.717496] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.731651] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.738546] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.778169] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.823506] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.829891] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.844863] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.856193] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.864760] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.873298] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.881912] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.893200] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.906841] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.914891] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.934057] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.942565] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.951194] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.959887] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.985941] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.991183] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.001297] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 9.007163] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.009661] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 9.017280] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.025817] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 9.032236] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 9.040176] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 9.041728] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.041770] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.041824] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.041865] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.043740] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.049528] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.106382] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.118045] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.126776] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.135470] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.144103] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.155245] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.171203] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.179339] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.207530] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.216269] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.224857] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.233409] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.244509] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.260249] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.268361] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.408318] caam algorithms registered in /proc/crypto <6>[ 9.424816] caam 2100000.crypto: registering rng-caam <6>[ 9.434231] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.442750] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.451540] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.460064] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) done <4>[ 9.470508] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: <4>[ 9.486487] panel-simple panel-lcd: supply power not found, using dummy regulator <5>[ 9.489316] random: dd: uninitialized urandom read (32 bytes read) <4>[ 9.494479] panel-simple panel-lcd: Specify missing connector_type OK Starting network: <6>[ 9.520505] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.529185] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) ip: RTNETLINK answers: File exist<6>[ 9.537809] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) s FAIL <6>[ 9.549051] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Starting dropbear sshd: <5>[ 9.586698] random: dropbear: uninitialized urandom read (32 bytes read) OK <5>[ 9.612575] random: crng init done /bin/sh: <5>[ 9.616461] random: 1 urandom warning(s) missed due to ratelimiting can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9334643/environment . /lava-9334643/environment / # /lava-9334643/bin/lava-test-runner /lava-9334643/0 /lava-9334643/bin/lava-test-runner /lava-9334643/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-9334643/0/tests/0_dmesg + cat uuid + UUID=9334643_1.5.2.4<8>[ 10.204623] .1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.251177] <8>[ 10.292685] <8>[ 10.333952] + set<8>[ 10.343872] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9334643/environment / # . /lava-9334643/environment/lava-9334643/bin/lava-test-runner /lava-9334643/1 / # /lava-9334643/bin/lava-test-runner /lava-9334643/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-9334643/1/tests/1_bootrr +<8>[ 10.856766] cat uuid + UUID=9334643_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9334643/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd 120000.hdmi /lava-9334643/1/../bin/lava-test-case <8>[ 11.924545] /lava-9334643/1/../bin/lava-test-case <8>[ 11.964020] /lava-9334643/1/../bin/lava-test-case <8>[ 11.988711] + set<8>[ 12.007769] +x / #