[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.101.101 (3 ms) => setenv serverip 192.168.101.1 setenv serverip 192.168.101.1 => tftp 0x10000000 10062467/tftp-deploy-xkd5kz2l/kernel/zImage tftp 0x10000000 10062467/tftp-deploy-xkd5kz2l/kernel/zImage Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '10062467/tftp-deploy-xkd5kz2l/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 2.2 MiB/s done Bytes transferred = 12526080 (bf2200 hex) => tftp 0x14000000 10062467/tftp-deploy-xkd5kz2l/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10062467/tftp-deploy-xkd5kz2l/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '10062467/tftp-deploy-xkd5kz2l/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# # 2.2 MiB/s done Bytes transferred = 15269371 (e8fdfb hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10062467/tftp-deploy-xkd5kz2l/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10062467/tftp-deploy-xkd5kz2l/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.101.1; our IP address is 192.168.101.101 Filename '10062467/tftp-deploy-xkd5kz2l/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 1.9 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/10062467/extract-nfsrootfs-dmfadwfc,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/10062467/extract-nfsrootfs-dmfadwfc,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbf2200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15269307 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.178-cip31 (KernelCI@build-j1380522-arm-gcc-10-multi-v7-defconfig-kselftest-rjzlm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Apr 20 13:50:40 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.101.1:/var/lib/lava/dispatcher/tmp/10062467/extract-nfsrootfs-dmfadwfc,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 921604K/1048576K available (17408K kernel code, 2659K rwdata, 8120K rodata, 2048K init, 6691K bss, 61436K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 56059 entries in 165 pages [ 0.000000] ftrace: allocated 165 pages with 4 groups [ 0.000000] Running RCU self tests [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU lockdep checking is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 15ns [ 0.000009] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns [ 0.000041] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns [ 0.004511] Console: colour dummy device 80x30 [ 0.004578] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar [ 0.004608] ... MAX_LOCKDEP_SUBCLASSES: 8 [ 0.004636] ... MAX_LOCK_DEPTH: 48 [ 0.004664] ... MAX_LOCKDEP_KEYS: 8192 [ 0.004691] ... CLASSHASH_SIZE: 4096 [ 0.004718] ... MAX_LOCKDEP_ENTRIES: 32768 [ 0.004745] ... MAX_LOCKDEP_CHAINS: 65536 [ 0.004771] ... CHAINHASH_SIZE: 32768 [ 0.004798] memory used by lock dependency info: 4061 kB [ 0.004825] memory used for stack traces: 2112 kB [ 0.004853] per task-struct memory footprint: 1536 bytes [ 0.004954] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) [ 0.005007] pid_max: default: 32768 minimum: 301 [ 0.005375] LSM: Security Framework initializing [ 0.005485] LSM support for eBPF active [ 0.005626] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005677] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.008241] CPU: Testing write buffer coherency: ok [ 0.008369] CPU0: Spectre v2: using BPIALL workaround [ 0.009392] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.012959] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.015343] rcu: Hierarchical SRCU implementation. [ 0.024237] EFI services will not be available. [ 0.025406] smp: Bringing up secondary CPUs ... [ 0.028315] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.028330] CPU1: Spectre v2: using BPIALL workaround [ 0.031865] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.031880] CPU2: Spectre v2: using BPIALL workaround [ 0.035054] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035069] CPU3: Spectre v2: using BPIALL workaround [ 0.035759] smp: Brought up 1 node, 4 CPUs [ 0.035795] SMP: Total of 4 processors activated (528.00 BogoMIPS). [ 0.035825] CPU: All CPU(s) started in SVC mode. [ 0.038226] devtmpfs: initialized [ 0.086937] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.089589] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.089659] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.094372] pinctrl core: initialized pinctrl subsystem [ 0.100908] DMI not present or invalid. [ 0.103085] NET: Registered protocol family 16 [ 0.112865] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.121562] thermal_sys: Registered thermal governor 'step_wise' [ 0.122065] cpuidle: using governor menu [ 0.122558] CPU identified as i.MX6Q, silicon rev 1.0 [ 0.760836] vdd1p1: supplied by regulator-dummy [ 0.788006] vdd3p0: supplied by regulator-dummy [ 0.814828] vdd2p5: supplied by regulator-dummy [ 0.841687] vddarm: supplied by regulator-dummy [ 0.869299] vddpu: supplied by regulator-dummy [ 0.895260] vddsoc: supplied by regulator-dummy [ 2.038733] No ATAGs? [ 2.039319] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 2.039396] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 2.056217] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 2.081544] Serial: AMBA PL011 UART driver [ 2.138589] Kprobes globally optimized [ 2.241748] iommu: Default domain type: Translated [ 2.243711] vgaarb: loaded [ 2.248049] SCSI subsystem initialized [ 2.250040] usbcore: registered new interface driver usbfs [ 2.250335] usbcore: registered new interface driver hub [ 2.250548] usbcore: registered new device driver usb [ 2.257326] i2c i2c-0: IMX I2C adapter registered [ 2.263457] i2c i2c-1: IMX I2C adapter registered [ 2.267454] i2c i2c-2: IMX I2C adapter registered [ 2.271525] pps_core: LinuxPPS API ver. 1 registered [ 2.271561] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.271653] PTP clock support registered [ 2.287388] clocksource: Switched to clocksource mxc_timer1 [ 3.903807] NET: Registered protocol family 2 [ 3.904565] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 3.907650] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) [ 3.907824] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 3.908034] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) [ 3.909476] TCP: Hash tables configured (established 8192 bind 8192) [ 3.910509] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) [ 3.910832] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) [ 3.911081] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) [ 3.911790] NET: Registered protocol family 1 [ 3.914480] RPC: Registered named UNIX socket transport module. [ 3.914562] RPC: Registered udp transport module. [ 3.914597] RPC: Registered tcp transport module. [ 3.914630] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 3.914682] NET: Registered protocol family 44 [ 3.914744] PCI: CLS 0 bytes, default 64 [ 3.916944] Trying to unpack rootfs image as initramfs... [ 5.696637] Freeing initrd memory: 14912K [ 5.697713] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 5.698801] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 5.706887] Initialise system trusted keyrings [ 5.708045] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 5.751660] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 5.755321] NFS: Registering the id_resolver key type [ 5.755489] Key type id_resolver registered [ 5.755573] Key type id_legacy registered [ 5.756139] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 5.756241] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 5.756434] ntfs: driver 2.1.32 [Flags: R/O]. [ 5.758552] Key type asymmetric registered [ 5.758675] Asymmetric key parser 'x509' registered [ 5.759055] bounce: pool size: 64 pages [ 5.759213] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 5.759315] io scheduler mq-deadline registered [ 5.759354] io scheduler kyber registered [ 5.760222] test_firmware: interface ready [ 5.917081] mxs-dma 110000.dma-apbh: initialized [ 5.974286] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 5.974537] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 6.199084] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 6.217476] SuperH (H)SCI(F) driver initialized [ 6.220209] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 6.224817] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 7.154371] printk: console [ttymxc1] enabled [ 7.164510] msm_serial: driver initialized [ 7.169657] STMicroelectronics ASC driver initialized [ 7.180662] STM32 USART driver initialized [ 7.204517] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 [ 7.225587] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.233943] panel-simple panel-lcd: Specify missing connector_type [ 7.241619] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.290937] brd: module loaded [ 7.344838] loop: module loaded [ 7.350895] lkdtm: No crash points registered, enable through debugfs [ 7.371380] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 7.379404] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 7.387503] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 7.395714] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 7.403724] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 7.411860] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 7.419646] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 7.430925] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 7.438036] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 7.446862] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 7.460802] scsi host0: ahci-imx [ 7.466132] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 7.525098] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 7.538270] pps pps0: new PPS source ptp0 [ 7.582152] fec 2188000.ethernet eth0: registered PHC device 0 [ 7.592345] e1000e: Intel(R) PRO/1000 Network Driver [ 7.597393] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 7.603564] igb: Intel(R) Gigabit Ethernet Network Driver [ 7.609039] igb: Copyright (c) 2007-2014 Intel Corporation. [ 7.634453] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 7.642076] usbcore: registered new interface driver pegasus [ 7.648020] usbcore: registered new interface driver asix [ 7.653580] usbcore: registered new interface driver ax88179_178a [ 7.659886] usbcore: registered new interface driver cdc_ether [ 7.665936] usbcore: registered new interface driver smsc75xx [ 7.671973] usbcore: registered new interface driver smsc95xx [ 7.677946] usbcore: registered new interface driver net1080 [ 7.683765] usbcore: registered new interface driver cdc_subset [ 7.689886] usbcore: registered new interface driver zaurus [ 7.695712] usbcore: registered new interface driver cdc_ncm [ 7.713038] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.719717] ehci-pci: EHCI PCI platform driver [ 7.724336] ehci-platform: EHCI generic platform driver [ 7.730559] ehci-orion: EHCI orion driver [ 7.735393] SPEAr-ehci: EHCI SPEAr driver [ 7.740250] ehci-st: EHCI STMicroelectronics driver [ 7.745912] ehci-exynos: EHCI Exynos driver [ 7.750961] ehci-atmel: EHCI Atmel driver [ 7.755747] tegra-ehci: Tegra EHCI driver [ 7.760659] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 7.766934] ohci-pci: OHCI PCI platform driver [ 7.771599] ohci-platform: OHCI generic platform driver [ 7.777765] SPEAr-ohci: OHCI SPEAr driver [ 7.782580] ohci-st: OHCI STMicroelectronics driver [ 7.788326] ohci-atmel: OHCI Atmel driver [ 7.795518] usbcore: registered new interface driver usb-storage [ 7.819789] ata1: SATA link down (SStatus 0 SControl 300) [ 7.825554] ahci-imx 2200000.sata: no device found, disabling link. [ 7.831058] i2c /dev entries driver [ 7.831911] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 7.910171] sdhci: Secure Digital Host Controller Interface driver [ 7.916387] sdhci: Copyright(c) Pierre Ossman [ 7.929498] Synopsys Designware Multimedia Card Interface Driver [ 7.942243] sdhci-pltfm: SDHCI platform and OF driver helper [ 7.951504] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 7.956708] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 7.963686] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 7.970607] ledtrig-cpu: registered to indicate activity on CPUs [ 7.980399] usbcore: registered new interface driver usbhid [ 7.986007] usbhid: USB HID core driver [ 8.007085] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 8.007097] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 8.012053] netem: version 1.3 [ 8.012318] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 8.014663] IPv4 over IPsec tunneling driver [ 8.038686] NET: Registered protocol family 10 [ 8.048614] Segment Routing with IPv6 [ 8.054785] mmc2: new high speed SDHC card at address 0001 [ 8.058089] NET: Registered protocol family 17 [ 8.064186] mmcblk2: mmc2:0001 SD 14.8 GiB [ 8.066470] 8021q: 802.1Q VLAN Support v1.8 [ 8.074419] Key type dns_resolver registered [ 8.090801] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 8.090857] ThumbEE CPU extension supported. [ 8.098386] GPT:29296874 != 30965759 [ 8.102680] Registering SWP/SWPB emulation handler [ 8.106241] GPT:Alternate GPT header not at the end of the disk. [ 8.112521] Loading compiled-in X.509 certificates [ 8.117128] GPT:29296874 != 30965759 [ 8.125636] GPT: Use GNU Parted to correct GPT errors. [ 8.130980] mmcblk2: p1 p2 p3 [ 8.313361] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.321919] panel-simple panel-lcd: Specify missing connector_type [ 8.335613] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.373814] imx_usb 2184200.usb: No over current polarity defined [ 8.387216] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 8.392719] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 8.428849] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 8.448176] hub 1-0:1.0: USB hub found [ 8.452538] hub 1-0:1.0: 1 port detected [ 8.467503] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data [ 8.474855] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem [ 8.483104] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 [ 8.511770] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.520186] panel-simple panel-lcd: Specify missing connector_type [ 8.533958] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.566412] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.574773] panel-simple panel-lcd: Specify missing connector_type [ 8.588532] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.608466] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 8.639100] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.647540] panel-simple panel-lcd: Specify missing connector_type [ 8.661224] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.683852] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) [ 8.857633] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 9.065837] hub 1-1:1.0: USB hub found [ 9.070542] hub 1-1:1.0: 3 ports detected [ 9.103758] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.112126] panel-simple panel-lcd: Specify missing connector_type [ 9.126072] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 10.799326] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 10.808153] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 10.837511] Sending DHCP requests ., OK [ 10.881776] IP-Config: Got DHCP answer from 192.168.101.1, my address is 192.168.101.101 [ 10.890013] IP-Config: Complete: [ 10.893276] device=eth0, hwaddr=00:19:b8:00:e5:47, ipaddr=192.168.101.101, mask=255.255.255.0, gw=192.168.101.1 [ 10.903879] host=imx6q-sabrelite-cbg-2, domain=lava.cbg.collabora.co.uk, nis-domain=(none) [ 10.912687] bootserver=192.168.101.1, rootserver=192.168.101.1, rootpath= [ 10.912707] nameserver0=192.168.101.1 [ 10.979886] Freeing unused kernel memory: 2048K [ 10.988522] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 15.463362] imx-ipuv3 2400000.ipu: IPUv3H probed [ 15.485971] imx-ipuv3 2800000.ipu: IPUv3H probed [ 15.494210] panel-simple panel-lcd: supply power not found, using dummy regulator [ 15.502889] panel-simple panel-lcd: Specify missing connector_type [ 15.516946] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 15.550585] panel-simple panel-lcd: supply power not found, using dummy regulator [ 15.559076] panel-simple panel-lcd: Specify missing connector_type [ 15.603219] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 15.617785] CAN device driver interface [ 15.660016] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 15.669119] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 15.691693] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 15.697664] panel-simple panel-lcd: supply power not found, using dummy regulator [ 15.700594] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 15.708318] panel-simple panel-lcd: Specify missing connector_type [ 15.775157] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 15.838263] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 15.859486] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 15.867196] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 15.872398] caam 2100000.crypto: Entropy delay = 3200 [ 15.873957] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 15.939863] caam 2100000.crypto: Instantiated RNG4 SH0 [ 16.000624] caam 2100000.crypto: Instantiated RNG4 SH1 [ 16.005892] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 16.012708] caam 2100000.crypto: job rings = 2, qi = 0 [ 16.020781] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 16.027670] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 16.033820] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 16.045064] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 16.053706] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 16.059826] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 [ 16.062708] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 16.077884] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 16.092320] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 16.101208] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 16.109867] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 16.118428] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 16.146935] panel-simple panel-lcd: supply power not found, using dummy regulator [ 16.155589] panel-simple panel-lcd: Specify missing connector_type [ 16.171057] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 16.193647] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 16.210273] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 16.236009] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 16.244771] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 16.253410] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 16.261957] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 16.293461] panel-simple panel-lcd: supply power not found, using dummy regulator [ 16.302107] panel-simple panel-lcd: Specify missing connector_type [ 16.320721] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 16.403173] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 16.412282] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 16.421138] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) [ 16.429915] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) [ 17.069715] caam algorithms registered in /proc/crypto [ 17.081453] caam 2100000.crypto: registering rng-caam [ 17.094661] panel-simple panel-lcd: supply power not found, using dummy regulator [ 17.110002] panel-simple panel-lcd: Specify missing connector_type [ 17.130776] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 17.169782] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) [ 17.178392] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) [ 17.186904] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) Begin: Loading essential drivers [ 17.195505] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) ... done. [ 17.213919] panel-simple panel-lcd: supply power not found, using dummy regulator Begin: Running /scripts/init-prem[ 17.222670] panel-simple panel-lcd: Specify missing connector_type ount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. [ 17.270281] random: crng init done IP-Config: eth0 hardware address 00:19:b8:00:e5:47 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.101.1): address: 192.168.101.101 broadcast: 192.168.101.255 netmask: 255.255.255.0 gateway: 192.168.101.1 dns0 : 192.168.101.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-cbg-2 domain : lava.cbg.collabora.co.uk rootserver: 192.168.101.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 20.275705] systemd[1]: System time before build time, advancing clock. [ 20.544016] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 20.570225] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 20.634657] systemd[1]: Set hostname to . [ 22.434276] systemd[1]: Queued start job for default target Graphical Interface. [ 22.449201] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 22.502616] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 22.543283] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 22.592581] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 22.642389] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 22.691655] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 22.739935] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 22.752766] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 22.799914] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 22.837890] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 22.878331] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 22.919377] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 22.962410] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 23.067078] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 23.085528] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 23.135089] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 23.184423] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 23.238841] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 23.283479] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 23.331546] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 23.341902] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 23.363605] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 23.409409] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 23.465555] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 23.519999] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 23.571165] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 23.629076] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 23.689020] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 23.723762] fuse: init (API version 7.32) [ 23.724131] systemd[1]: Starting Journal Service... Starting Journal Service... [ 23.808131] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 23.869191] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 23.929719] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 24.001108] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 24.050975] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 24.108723] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 24.209142] systemd[1]: modprobe@configfs.service: Succeeded. [ 24.219801] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 24.274052] systemd[1]: modprobe@drm.service: Succeeded. [ 24.284258] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. [ 24.344613] systemd[1]: modprobe@fuse.service: Succeeded. [ 24.354897] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. [ 24.413606] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. [ 24.463385] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. [ 24.509353] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create System Users... [ 24.846834] systemd-journald[282]: Received client request to flush runtime journal. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.178-cip31 #1 SMP Thu Apr 20 13:50:40 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10062467/extract-nfsrootfs-dmfadwfc' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10062467/extract-nfsrootfs-dmfadwfc' / # export NFS_SERVER_IP='192.168.101.1' export NFS_SERVER_IP='192.168.101.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10062467/environment . /lava-10062467/environment / # /lava-10062467/bin/lava-test-runner /lava-10062467/0 /lava-10062467/bin/lava-test-runner /lava-10062467/0 + export TESTRUN_ID=0_dmesg + cd /lava-10062467/0/tests/0_dmesg + cat uuid + UUID=10062467_1.6.2.4.1[ 46.996570] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 47.294445] [ 47.507764] [ 47.717931] + set +x [ 47.728987] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh. /lava-10062467/environment / # . /lava-10062467/environment/lava-10062467/bin/lava-test-runner /lava-10062467/1 / # /lava-10062467/bin/lava-test-runner /lava-10062467/1 + export TESTRUN_ID=1_bootrr + cd /lava-10062467/1/tests/1_bootrr + cat uuid + UUID=10062467_1.6.2.4.5[ 48.569272] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10062467/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds ldb panel-lcd /lava-10062467/1/../bin/lava-test-case [ 49.934755] /lava-10062467/1/../bin/lava-test-case [ 50.155955] /lava-10062467/1/../bin/lava-test-case [ 50.252549] + set +x [ 50.326575] / #