[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Couldn't find partition mmc 0:1 Error selecting device File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (13 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10062673/tftp-deploy-s2mdtm61/kernel/zImage tftp 0x10000000 10062673/tftp-deploy-s2mdtm61/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10062673/tftp-deploy-s2mdtm61/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 10.9 MiB/s done Bytes transferred = 9695744 (93f200 hex) => tftp 0x14000000 10062673/tftp-deploy-s2mdtm61/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10062673/tftp-deploy-s2mdtm61/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10062673/tftp-deploy-s2mdtm61/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 10.7 MiB/s done Bytes transferred = 12140602 (b9403a hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10062673/tftp-deploy-s2mdtm61/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10062673/tftp-deploy-s2mdtm61/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10062673/tftp-deploy-s2mdtm61/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.4 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10062673/extract-nfsrootfs-2bnw8iz0,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10062673/extract-nfsrootfs-2bnw8iz0,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x93f200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12140538 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.178-cip31 (KernelCI@build-j1380518-arm-gcc-10-multi-v7-defconfig-xr4f7) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Apr 20 13:50:11 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10062673/extract-nfsrootfs-2bnw8iz0,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 936500K/1048576K available (14336K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 46540K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000025] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.004243] Console: colour dummy device 80x30 [ 0.004296] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.004314] pid_max: default: 32768 minimum: 301 [ 0.004495] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004518] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.005162] CPU: Testing write buffer coherency: ok [ 0.005200] CPU0: Spectre v2: using BPIALL workaround [ 0.005459] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.006169] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007917] rcu: Hierarchical SRCU implementation. [ 0.011884] EFI services will not be available. [ 0.012199] smp: Bringing up secondary CPUs ... [ 0.013008] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.013017] CPU1: Spectre v2: using BPIALL workaround [ 0.013940] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.013949] CPU2: Spectre v2: using BPIALL workaround [ 0.014850] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.014859] CPU3: Spectre v2: using BPIALL workaround [ 0.014984] smp: Brought up 1 node, 4 CPUs [ 0.014997] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.015006] CPU: All CPU(s) started in SVC mode. [ 0.015575] devtmpfs: initialized [ 0.023042] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.023294] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.023318] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.026445] pinctrl core: initialized pinctrl subsystem [ 0.028362] DMI not present or invalid. [ 0.029260] NET: Registered protocol family 16 [ 0.032741] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.035169] thermal_sys: Registered thermal governor 'step_wise' [ 0.035356] cpuidle: using governor menu [ 0.035544] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.204975] vdd1p1: supplied by regulator-dummy [ 0.211986] vdd3p0: supplied by regulator-dummy [ 0.218932] vdd2p5: supplied by regulator-dummy [ 0.225906] vddarm: supplied by regulator-dummy [ 0.233021] vddpu: supplied by regulator-dummy [ 0.239849] vddsoc: supplied by regulator-dummy [ 0.558092] No ATAGs? [ 0.558252] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.558263] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.562509] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.568764] Serial: AMBA PL011 UART driver [ 0.571549] printk: console [ramoops-1] enabled [ 0.571768] pstore: Registered ramoops as persistent store backend [ 0.571781] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.604493] iommu: Default domain type: Translated [ 0.604932] vgaarb: loaded [ 0.605852] SCSI subsystem initialized [ 0.606437] usbcore: registered new interface driver usbfs [ 0.606501] usbcore: registered new interface driver hub [ 0.606552] usbcore: registered new device driver usb [ 0.608119] i2c i2c-0: IMX I2C adapter registered [ 0.609516] i2c i2c-1: IMX I2C adapter registered [ 0.610342] i2c i2c-2: IMX I2C adapter registered [ 0.611758] pps_core: LinuxPPS API ver. 1 registered [ 0.611773] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.611802] PTP clock support registered [ 0.615717] clocksource: Switched to clocksource mxc_timer1 [ 1.676610] NET: Registered protocol family 2 [ 1.677065] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.678238] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.678283] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.678372] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.678529] TCP: Hash tables configured (established 8192 bind 8192) [ 1.678754] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.678805] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.678991] NET: Registered protocol family 1 [ 1.679614] RPC: Registered named UNIX socket transport module. [ 1.679631] RPC: Registered udp transport module. [ 1.679642] RPC: Registered tcp transport module. [ 1.679652] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.679670] PCI: CLS 0 bytes, default 64 [ 1.680156] Trying to unpack rootfs image as initramfs... [ 2.631576] Freeing initrd memory: 11860K [ 2.632027] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.632412] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.634305] Initialise system trusted keyrings [ 2.634634] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.640556] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.641312] NFS: Registering the id_resolver key type [ 2.641361] Key type id_resolver registered [ 2.641374] Key type id_legacy registered [ 2.641482] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.641497] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.641536] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.642010] Key type asymmetric registered [ 2.642027] Asymmetric key parser 'x509' registered [ 2.642089] bounce: pool size: 64 pages [ 2.642138] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.642154] io scheduler mq-deadline registered [ 2.642166] io scheduler kyber registered [ 2.683023] mxs-dma 110000.dma-apbh: initialized [ 2.688086] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.688111] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.750180] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.754813] SuperH (H)SCI(F) driver initialized [ 2.755910] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.756938] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 3.585356] printk: console [ttymxc1] enabled [ 3.591167] msm_serial: driver initialized [ 3.595554] STMicroelectronics ASC driver initialized [ 3.602708] STM32 USART driver initialized [ 3.618500] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.626171] panel-simple panel-lcd: Specify missing connector_type [ 3.632734] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.649500] brd: module loaded [ 3.662564] loop: module loaded [ 3.669785] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 3.677757] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 3.685788] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 3.693975] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 3.701729] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 3.709227] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 3.716528] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 3.726848] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 3.733844] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.742670] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 3.753243] scsi host0: ahci-imx [ 3.756886] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 3.777554] CAN device driver interface [ 3.782827] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 3.792138] pps pps0: new PPS source ptp0 [ 3.814573] fec 2188000.ethernet eth0: registered PHC device 0 [ 3.821998] e1000e: Intel(R) PRO/1000 Network Driver [ 3.826995] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.832982] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.838405] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.850472] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.857942] usbcore: registered new interface driver pegasus [ 3.863646] usbcore: registered new interface driver asix [ 3.869105] usbcore: registered new interface driver ax88179_178a [ 3.875236] usbcore: registered new interface driver cdc_ether [ 3.881133] usbcore: registered new interface driver smsc75xx [ 3.886954] usbcore: registered new interface driver smsc95xx [ 3.892738] usbcore: registered new interface driver net1080 [ 3.898455] usbcore: registered new interface driver cdc_subset [ 3.904413] usbcore: registered new interface driver zaurus [ 3.910074] usbcore: registered new interface driver cdc_ncm [ 3.919510] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.926066] ehci-pci: EHCI PCI platform driver [ 3.930554] ehci-platform: EHCI generic platform driver [ 3.936116] ehci-orion: EHCI orion driver [ 3.940359] SPEAr-ehci: EHCI SPEAr driver [ 3.944562] ehci-st: EHCI STMicroelectronics driver [ 3.949657] ehci-exynos: EHCI Exynos driver [ 3.954028] ehci-atmel: EHCI Atmel driver [ 3.958245] tegra-ehci: Tegra EHCI driver [ 3.962478] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.968712] ohci-pci: OHCI PCI platform driver [ 3.973212] ohci-platform: OHCI generic platform driver [ 3.978739] SPEAr-ohci: OHCI SPEAr driver [ 3.982943] ohci-st: OHCI STMicroelectronics driver [ 3.988054] ohci-atmel: OHCI Atmel driver [ 3.993201] usbcore: registered new interface driver usb-storage [ 4.007627] i2c /dev entries driver [ 4.031112] sdhci: Secure Digital Host Controller Interface driver [ 4.037325] sdhci: Copyright(c) Pierre Ossman [ 4.044536] Synopsys Designware Multimedia Card Interface Driver [ 4.052620] sdhci-pltfm: SDHCI platform and OF driver helper [ 4.062352] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 4.063986] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 4.067407] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 4.077582] ledtrig-cpu: registered to indicate activity on CPUs [ 4.084682] usbcore: registered new interface driver usbhid [ 4.090298] usbhid: USB HID core driver [ 4.097833] ata1: SATA link down (SStatus 0 SControl 300) [ 4.100941] NET: Registered protocol family 10 [ 4.103283] ahci-imx 2200000.sata: no device found, disabling link. [ 4.104200] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 4.108798] Segment Routing with IPv6 [ 4.114001] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 4.115794] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 4.120973] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 4.145133] NET: Registered protocol family 17 [ 4.149629] can: controller area network core [ 4.154067] NET: Registered protocol family 29 [ 4.158547] can: raw protocol [ 4.159327] mmc2: new high speed SDHC card at address 59b4 [ 4.161526] can: broadcast manager protocol [ 4.167914] mmcblk2: mmc2:59b4 SD 14.7 GiB [ 4.171224] can: netlink gateway - max_hops=1 [ 4.180581] Key type dns_resolver registered [ 4.183411] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 4.192294] GPT:29296874 != 30863359 [ 4.194239] ThumbEE CPU extension supported. [ 4.195902] GPT:Alternate GPT header not at the end of the disk. [ 4.195907] GPT:29296874 != 30863359 [ 4.195915] GPT: Use GNU Parted to correct GPT errors. [ 4.200196] Registering SWP/SWPB emulation handler [ 4.206249] mmcblk2: p1 p2 p3 [ 4.210132] Loading compiled-in X.509 certificates [ 4.232707] pstore: Using crash dump compression: deflate [ 4.260074] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.267763] panel-simple panel-lcd: Specify missing connector_type [ 4.275496] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.294414] imx_usb 2184200.usb: No over current polarity defined [ 4.304789] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 4.309812] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 4.345672] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 4.352447] hub 1-0:1.0: USB hub found [ 4.356328] hub 1-0:1.0: 1 port detected [ 4.362758] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 4.378853] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.386719] panel-simple panel-lcd: Specify missing connector_type [ 4.394462] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.406636] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.414250] panel-simple panel-lcd: Specify missing connector_type [ 4.421961] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.431797] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.443312] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.450958] panel-simple panel-lcd: Specify missing connector_type [ 4.458674] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 4.472182] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 4.685705] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 4.887361] hub 1-1:1.0: USB hub found [ 4.891326] hub 1-1:1.0: 3 ports detected [ 4.906196] panel-simple panel-lcd: supply power not found, using dummy regulator [ 4.913833] panel-simple panel-lcd: Specify missing connector_type [ 4.921640] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.606138] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 7.635722] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.665698] Sending DHCP requests ., OK [ 7.709576] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 [ 7.717635] IP-Config: Complete: [ 7.720893] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 [ 7.731352] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) [ 7.739195] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 7.739201] nameserver0=192.168.201.1 [ 7.756016] Freeing unused kernel memory: 2048K [ 7.796756] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 8.636730] imx-ipuv3 2400000.ipu: IPUv3H probed [ 8.651273] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.666314] imx-ipuv3 2800000.ipu: IPUv3H probed [ 8.681711] panel-simple panel-lcd: Specify missing connector_type [ 8.692859] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.715838] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 8.724195] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 8.724271] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.732569] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 8.740151] panel-simple panel-lcd: Specify missing connector_type [ 8.748300] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 8.771385] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 8.786615] panel-simple panel-lcd: supply power not found, using dummy regulator [ 8.794310] panel-simple panel-lcd: Specify missing connector_type [ 8.824809] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 8.832265] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 8.839699] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 8.844945] caam 2100000.crypto: Entropy delay = 3200 [ 8.846287] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 8.909777] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 8.912144] caam 2100000.crypto: Instantiated RNG4 SH0 [ 8.919696] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 8.940957] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 8.948897] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 8.957296] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 8.965312] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 8.972909] caam 2100000.crypto: Instantiated RNG4 SH1 [ 8.978686] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 8.985326] caam 2100000.crypto: job rings = 2, qi = 0 [ 8.995394] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 9.002905] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 9.009168] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 9.019138] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 9.028789] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.037189] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.045473] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.053786] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.065483] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.095643] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.103340] panel-simple panel-lcd: Specify missing connector_type [ 9.130540] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.138931] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.147245] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.155503] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 9.337115] caam algorithms registered in /proc/crypto [ 9.343653] caam 2100000.crypto: registering rng-caam [ 9.350566] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 9.363983] panel-simple panel-lcd: supply power not found, using dummy regulator [ 9.371655] panel-simple panel-lcd: Specify missing connector_type [ 9.381674] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 9.389962] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 9.398227] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 9.406467] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. [ 9.531179] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 10.422530] systemd[1]: System time before build time, advancing clock. [ 10.473846] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 10.497811] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 10.538705] systemd[1]: Set hostname to . [ 11.398503] systemd[1]: Queued start job for default target Graphical Interface. [ 11.407698] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 11.420153] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 11.429454] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 11.467068] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 11.507010] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 11.546626] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 11.586466] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 11.626336] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 11.665947] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 11.677868] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 11.716646] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 11.746082] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 11.785767] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 11.816219] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 11.846972] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 11.921018] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 11.931047] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 11.967277] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 12.008428] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 12.050121] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 12.087172] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 12.126327] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 12.134976] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 12.147191] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 12.192688] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 12.230811] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 12.270836] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 12.308820] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 12.349399] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 12.389520] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 12.402320] systemd[1]: Starting Journal Service... Starting Journal Service... [ 12.444777] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 12.478847] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 12.518980] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 12.561295] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 12.596331] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 12.636834] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 12.698367] systemd[1]: modprobe@configfs.service: Succeeded. [ 12.704869] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 12.746299] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... [ 13.004226] systemd-journald[275]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.178-cip31 #1 SMP Thu Apr 20 13:50:11 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10062673/extract-nfsrootfs-2bnw8iz0' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10062673/extract-nfsrootfs-2bnw8iz0' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-10062673/environment . /lava-10062673/environment / #/lava-10062673/bin/lava-test-runner /lava-10062673/0 /lava-10062673/bin/lava-test-runner /lava-10062673/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-10062673/0/tests/0_timesync-off ++ cat uuid + UUID=10062673_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-10062673/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=10062673_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.177-cip31-122-gfb6ca504156b4/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-04-20 14:13:26-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.177-cip31-122-gfb6ca504156b4/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1408824 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 1%[ ] 16.21K 57.3KB/s kselftest.tar.xz 3%[ ] 52.05K 91.8KB/s kselftest.tar.xz 5%[> ] 75.60K 84.5KB/s kselftest.tar.xz 7%[> ] 100.13K 88.1KB/s kselftest.tar.xz 9%[> ] 129.82K 91.4KB/s kselftest.tar.xz 11%[=> ] 160.93K 94.4KB/s kselftest.tar.xz 14%[=> ] 193.46K 97.2KB/s kselftest.tar.xz 16%[==> ] 228.81K 101KB/s kselftest.tar.xz 19%[==> ] 267.92K 99.2KB/s kselftest.tar.xz 22%[===> ] 303.75K 96.9KB/s eta 11s kselftest.tar.xz 24%[===> ] 332.03K 97.1KB/s eta 11s kselftest.tar.xz 24%[===> ] 340.52K 92.0KB/s eta 11s kselftest.tar.xz 26%[====> ] 361.73K 91.7KB/s eta 11s kselftest.tar.xz 26%[====> ] 370.21K 88.7KB/s eta 11s kselftest.tar.xz 28%[====> ] 387.18K 86.9KB/s eta 11s kselftest.tar.xz 29%[====> ] 405.57K 85.5KB/s eta 11s kselftest.tar.xz 30%[=====> ] 423.95K 87.4KB/s eta 11s kselftest.tar.xz 31%[=====> ] 438.09K 84.4KB/s eta 11s kselftest.tar.xz 33%[=====> ] 462.13K 85.7KB/s eta 11s kselftest.tar.xz 35%[======> ] 487.58K 85.3KB/s eta 11s kselftest.tar.xz 36%[======> ] 505.96K 84.5KB/s eta 11s kselftest.tar.xz 39%[======> ] 537.07K 86.3KB/s eta 11s kselftest.tar.xz 40%[=======> ] 558.28K 85.7KB/s eta 9s kselftest.tar.xz 42%[=======> ] 583.74K 85.9KB/s eta 9s kselftest.tar.xz 43%[=======> ] 598.81K 82.8KB/s eta 9s kselftest.tar.xz 45%[========> ] 627.09K 82.7KB/s eta 9s kselftest.tar.xz 46%[========> ] 645.96K 83.6KB/s eta 9s kselftest.tar.xz 48%[========> ] 670.00K 79.8KB/s eta 8s kselftest.tar.xz 49%[========> ] 685.07K 81.9KB/s eta 8s kselftest.tar.xz 51%[=========> ] 712.42K 80.4KB/s eta 8s kselftest.tar.xz 53%[=========> ] 729.39K 83.5KB/s eta 8s kselftest.tar.xz 54%[=========> ] 743.53K 81.5KB/s eta 7s kselftest.tar.xz 55%[==========> ] 760.50K 83.8KB/s eta 7s kselftest.tar.xz 56%[==========> ] 776.05K 84.3KB/s eta 7s kselftest.tar.xz 57%[==========> ] 795.85K 85.3KB/s eta 7s kselftest.tar.xz 59%[==========> ] 818.47K 86.9KB/s eta 7s kselftest.tar.xz 60%[===========> ] 834.03K 86.2KB/s eta 6s kselftest.tar.xz 62%[===========> ] 855.24K 83.4KB/s eta 6s kselftest.tar.xz 64%[===========> ] 880.69K 83.7KB/s eta 6s kselftest.tar.xz 65%[============> ] 907.56K 82.2KB/s eta 6s kselftest.tar.xz 67%[============> ] 922.63K 79.5KB/s eta 5s kselftest.tar.xz 69%[============> ] 949.98K 78.7KB/s eta 5s kselftest.tar.xz 70%[=============> ] 971.19K 79.1KB/s eta 5s kselftest.tar.xz 71%[=============> ] 989.09K 76.3KB/s eta 5s kselftest.tar.xz 73%[=============> ] 1011K 76.5KB/s eta 4s kselftest.tar.xz 75%[==============> ] 1.01M 78.5KB/s eta 4s kselftest.tar.xz 76%[==============> ] 1.03M 78.4KB/s eta 4s kselftest.tar.xz 78%[==============> ] 1.06M 81.9KB/s eta 4s kselftest.tar.xz 80%[===============> ] 1.08M 83.4KB/s eta 3s kselftest.tar.xz 82%[===============> ] 1.10M 85.3KB/s eta 3s kselftest.tar.xz 83%[===============> ] 1.12M 84.3KB/s eta 3s kselftest.tar.xz 85%[================> ] 1.15M 86.5KB/s eta 3s kselftest.tar.xz 85%[================> ] 1.15M 84.1KB/s eta 3s kselftest.tar.xz 87%[================> ] 1.17M 86.0KB/s eta 2s kselftest.tar.xz 88%[================> ] 1.19M 85.5KB/s eta 2s kselftest.tar.xz 89%[================> ] 1.21M 85.2KB/s eta 2s kselftest.tar.xz 91%[=================> ] 1.22M 84.9KB/s eta 2s kselftest.tar.xz 92%[=================> ] 1.24M 85.6KB/s eta 2s kselftest.tar.xz 94%[=================> ] 1.27M 87.8KB/s eta 1s kselftest.tar.xz 95%[==================> ] 1.29M 87.4KB/s eta 1s kselftest.tar.xz 97%[==================> ] 1.31M 90.4KB/s eta 1s kselftest.tar.xz 99%[==================> ] 1.34M 92.9KB/s eta 1s kselftest.tar.xz 100%[===================>] 1.34M 92.8KB/s in 16s 2023-04-20 14:13:42 (86.6 KB/s) - 'kselftest.tar.xz' saved [1408824/1408824] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== [ 48.766595] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #