[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (17 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10527131/tftp-deploy-6_r1sny2/kernel/zImage tftp 0x10000000 10527131/tftp-deploy-6_r1sny2/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10527131/tftp-deploy-6_r1sny2/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 11.5 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 10527131/tftp-deploy-6_r1sny2/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10527131/tftp-deploy-6_r1sny2/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10527131/tftp-deploy-6_r1sny2/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.2 MiB/s done Bytes transferred = 12144431 (b94f2f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10527131/tftp-deploy-6_r1sny2/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10527131/tftp-deploy-6_r1sny2/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '10527131/tftp-deploy-6_r1sny2/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10527131/extract-nfsrootfs-8o0tm41s,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10527131/extract-nfsrootfs-8o0tm41s,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12144367 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.181-cip34 (KernelCI@build-j1586965-arm-gcc-10-multi-v7-defconfig-72vgv) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue May 30 15:46:59 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10527131/extract-nfsrootfs-8o0tm41s,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936500K/1048576K available (14336K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 46540K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022456] Console: colour dummy device 80x30 <6>[ 0.024348] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034758] pid_max: default: 32768 minimum: 301 <6>[ 0.039795] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047210] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055836] CPU: Testing write buffer coherency: ok <6>[ 0.060325] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065896] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072246] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.080024] rcu: Hierarchical SRCU implementation. <6>[ 0.087143] EFI services will not be available. <6>[ 0.089385] smp: Bringing up secondary CPUs ... <6>[ 0.094664] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094672] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.106054] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.106061] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.117216] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.117224] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127661] smp: Brought up 1 node, 4 CPUs <6>[ 0.131887] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138346] CPU: All CPU(s) started in SVC mode. <6>[ 0.143771] devtmpfs: initialized <6>[ 0.154021] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159366] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169235] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179442] pinctrl core: initialized pinctrl subsystem <6>[ 0.183925] DMI not present or invalid. <6>[ 0.187025] NET: Registered protocol family 16 <6>[ 0.194252] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200915] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201105] cpuidle: using governor menu <6>[ 0.209181] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.389209] vdd1p1: supplied by regulator-dummy <6>[ 0.398372] vdd3p0: supplied by regulator-dummy <6>[ 0.407459] vdd2p5: supplied by regulator-dummy <6>[ 0.416572] vddarm: supplied by regulator-dummy <6>[ 0.425837] vddpu: supplied by regulator-dummy <6>[ 0.434691] vddsoc: supplied by regulator-dummy <6>[ 0.765747] No ATAGs? <6>[ 0.765932] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.773689] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.784078] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.794655] Serial: AMBA PL011 UART driver <6>[ 0.798998] printk: console [ramoops-1] enabled <6>[ 0.801155] pstore: Registered ramoops as persistent store backend <6>[ 0.807414] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.845360] iommu: Default domain type: Translated <6>[ 0.848141] vgaarb: loaded <5>[ 0.851499] SCSI subsystem initialized <6>[ 0.855151] usbcore: registered new interface driver usbfs <6>[ 0.860446] usbcore: registered new interface driver hub <6>[ 0.865972] usbcore: registered new device driver usb <6>[ 0.872804] i2c i2c-0: IMX I2C adapter registered <6>[ 0.877559] i2c i2c-1: IMX I2C adapter registered <6>[ 0.881969] i2c i2c-2: IMX I2C adapter registered <6>[ 0.887567] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.891324] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.900758] PTP clock support registered <6>[ 0.908881] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.970246] NET: Registered protocol family 2 <6>[ 1.972443] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.980862] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.988322] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.996398] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.003836] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.010537] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.017208] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.024692] NET: Registered protocol family 1 <6>[ 2.029718] RPC: Registered named UNIX socket transport module. <6>[ 2.035268] RPC: Registered udp transport module. <6>[ 2.040259] RPC: Registered tcp transport module. <6>[ 2.045183] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.051912] PCI: CLS 0 bytes, default 64 <6>[ 2.056581] Trying to unpack rootfs image as initramfs... <6>[ 3.018935] Freeing initrd memory: 11860K <4>[ 3.020839] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.028058] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.037998] Initialise system trusted keyrings <6>[ 3.041199] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.053347] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.057352] NFS: Registering the id_resolver key type <5>[ 3.061987] Key type id_resolver registered <5>[ 3.066337] Key type id_legacy registered <6>[ 3.070721] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.077563] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.085264] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.090328] Key type asymmetric registered <5>[ 3.094180] Asymmetric key parser 'x509' registered <6>[ 3.099382] bounce: pool size: 64 pages <6>[ 3.103431] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.111075] io scheduler mq-deadline registered <6>[ 3.115842] io scheduler kyber registered <6>[ 3.161670] mxs-dma 110000.dma-apbh: initialized <4>[ 3.168546] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.175495] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.226758] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.235126] SuperH (H)SCI(F) driver initialized <6>[ 3.238107] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.246999] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.254871] printk: console [ttymxc1] enabled <6>[ 3.254871] printk: console [ttymxc1] enabled <6>[ 3.264053] printk: bootconsole [ec_imx21] disabled <6>[ 3.264053] printk: bootconsole [ec_imx21] disabled <6>[ 3.275879] msm_serial: driver initialized <6>[ 3.281807] STMicroelectronics ASC driver initialized <6>[ 3.289219] STM32 USART driver initialized <4>[ 3.305341] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.313266] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.320105] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.336782] brd: module loaded <6>[ 3.350189] loop: module loaded <6>[ 3.357671] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.365912] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.374219] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.382699] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.390715] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.398444] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.406022] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.416640] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.423921] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.433000] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.443816] scsi host0: ahci-imx <6>[ 3.447672] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.468756] CAN device driver interface <6>[ 3.474291] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.483833] pps pps0: new PPS source ptp0 <6>[ 3.506136] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.513828] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.519086] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.525332] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.531016] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.543332] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.551061] usbcore: registered new interface driver pegasus <6>[ 3.557028] usbcore: registered new interface driver asix <6>[ 3.562745] usbcore: registered new interface driver ax88179_178a <6>[ 3.569155] usbcore: registered new interface driver cdc_ether <6>[ 3.575309] usbcore: registered new interface driver smsc75xx <6>[ 3.581382] usbcore: registered new interface driver smsc95xx <6>[ 3.587430] usbcore: registered new interface driver net1080 <6>[ 3.593409] usbcore: registered new interface driver cdc_subset <6>[ 3.599641] usbcore: registered new interface driver zaurus <6>[ 3.605547] usbcore: registered new interface driver cdc_ncm <6>[ 3.615304] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.622123] ehci-pci: EHCI PCI platform driver <6>[ 3.626875] ehci-platform: EHCI generic platform driver <6>[ 3.632707] ehci-orion: EHCI orion driver <6>[ 3.637222] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.641718] ehci-st: EHCI STMicroelectronics driver <6>[ 3.647061] ehci-exynos: EHCI Exynos driver <6>[ 3.651722] ehci-atmel: EHCI Atmel driver <6>[ 3.656212] tegra-ehci: Tegra EHCI driver <6>[ 3.660745] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.667209] ohci-pci: OHCI PCI platform driver <6>[ 3.671983] ohci-platform: OHCI generic platform driver <6>[ 3.677744] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.682235] ohci-st: OHCI STMicroelectronics driver <6>[ 3.687575] ohci-atmel: OHCI Atmel driver <6>[ 3.693008] usbcore: registered new interface driver usb-storage <6>[ 3.707736] i2c /dev entries driver <6>[ 3.731834] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.738288] sdhci: Copyright(c) Pierre Ossman <6>[ 3.745809] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.754152] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.761455] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.765813] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.766740] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.777439] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.784846] usbcore: registered new interface driver usbhid <6>[ 3.790719] usbhid: USB HID core driver <6>[ 3.800922] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.801607] NET: Registered protocol family 10 <6>[ 3.803768] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.806637] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.808867] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.812375] Segment Routing with IPv6 <6>[ 3.818475] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.825102] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.844169] mmc2: new high speed SDHC card at address 0001 <6>[ 3.850311] NET: Registered protocol family 17 <6>[ 3.860253] can: controller area network core <6>[ 3.860953] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 3.864963] NET: Registered protocol family 29 <6>[ 3.874088] can: raw protocol <6>[ 3.877333] can: broadcast manager protocol <6>[ 3.881821] can: netlink gateway - max_hops=1 <5>[ 3.886929] Key type dns_resolver registered <6>[ 3.893582] ThumbEE CPU extension supported. <5>[ 3.898135] Registering SWP/SWPB emulation handler <5>[ 3.903765] Loading compiled-in X.509 certificates <6>[ 3.914363] pstore: Using crash dump compression: deflate <4>[ 3.916220] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 3.927766] GPT:7812499 != 30560255 <4>[ 3.931577] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.937864] GPT:7812499 != 30560255 <4>[ 3.941528] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.941646] GPT: Use GNU Parted to correct GPT errors. <4>[ 3.949541] panel-simple panel-lcd: Specify missing connector_type <6>[ 3.954829] mmcblk2: p1 p2 p3 <4>[ 3.962809] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.981316] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.991195] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.996361] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.028898] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.035929] hub 1-0:1.0: USB hub found <6>[ 4.040079] hub 1-0:1.0: 1 port detected <6>[ 4.048871] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.065947] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.073877] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.081886] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.094250] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.102158] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.110114] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.120184] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.132551] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.140477] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.148493] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.162325] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.378818] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.580498] hub 1-1:1.0: USB hub found <6>[ 4.584714] hub 1-1:1.0: 3 ports detected <4>[ 4.599686] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.607562] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.615619] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.279305] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.288859] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.318858] Sending DHCP requests ., OK <6>[ 7.363032] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 7.371356] IP-Config: Complete: <6>[ 7.374877] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.385651] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 7.393799] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.393812] nameserver0=192.168.201.1 <6>[ 7.414578] Freeing unused kernel memory: 2048K <6>[ 7.439295] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 8.276575] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.288030] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.308958] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.317623] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.327938] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.343630] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.351692] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.369577] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.379192] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.384616] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.387787] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.404104] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.408857] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.412701] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.421079] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.450749] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.458691] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.481654] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.489255] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.496826] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.497017] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.509000] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.562972] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.620132] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.623752] caam 2100000.crypto: Instantiated RNG4 SH1 <4>[ 8.628279] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 8.633524] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <4>[ 8.642153] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 8.648871] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 8.662499] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.669883] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.676530] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.680452] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.683128] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.697048] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.704457] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.714931] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.723602] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.732299] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.740967] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.751548] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.766964] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.775079] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.786396] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.795074] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.803797] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.812437] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.833451] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.848510] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.856619] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.867559] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.876304] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.885076] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.893711] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.103436] caam algorithms registered in /proc/crypto <6>[ 9.110242] caam 2100000.crypto: registering rng-caam <4>[ 9.117363] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.131025] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.139120] panel-simple panel-lcd: Specify missing connector_type Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done<6>[ 9.157989] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) . Begin: Running /scripts/nfs-pr<6>[ 9.169259] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) emount ... Waiting up to 60 secs <6>[ 9.180613] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) for any ethernet to become availa<6>[ 9.191878] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) ble Device /sys/class/net/eth0 found done. <5>[ 9.298033] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.281172] systemd[1]: System time before build time, advancing clock. <30>[ 10.361807] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.385903] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.441874] systemd[1]: Set hostname to . <30>[ 11.317050] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.326716] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.339782] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.349310] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.390216] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.429457] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.469865] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.509569] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.549166] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.589480] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.602251] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.639668] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.669267] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.709143] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.739320] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.770020] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.845988] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.856491] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.890422] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.931488] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.972567] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 12.010213] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 12.050047] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 12.059634] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 12.072239] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 12.112741] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 12.153403] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 12.192417] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 12.232474] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 12.272442] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.313576] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.326822] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.367221] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.402578] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.442046] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.485496] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.519534] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.560063] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.621793] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... Starting Create System Users... <46>[ 12.971280] systemd-journald[286]: Received client request to flush runtime journal. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.181-cip34 #1 SMP Tue May 30 15:46:59 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10527131/extract-nfsrootfs-8o0tm41s' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10527131/extract-nfsrootfs-8o0tm41s' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-10527131/environment . /lava-10527131/environment / # /lava-10527131/bin/lava-test-runner /lava-10527131/0 /lava-10527131/bin/lava-test-runner /lava-10527131/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-10527131/0/tests/0_timesync-off ++ cat uuid + UUID=10527131_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-10527131/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=10527131_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.180-cip34-213-g6582dd41d2c22/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-05-30 16:05:45-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.180-cip34-213-g6582dd41d2c22/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1408556 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 2%[ ] 28.94K 100KB/s kselftest.tar.xz 4%[ ] 58.64K 80.8KB/s kselftest.tar.xz 8%[> ] 119.92K 118KB/s kselftest.tar.xz 9%[> ] 129.34K 99.0KB/s kselftest.tar.xz 12%[=> ] 168.00K 105KB/s kselftest.tar.xz 13%[=> ] 184.97K 98.1KB/s kselftest.tar.xz 15%[==> ] 210.42K 96.7KB/s kselftest.tar.xz 16%[==> ] 230.22K 93.4KB/s kselftest.tar.xz 18%[==> ] 254.26K 92.2KB/s kselftest.tar.xz 20%[===> ] 281.13K 92.3KB/s eta 12s kselftest.tar.xz 21%[===> ] 289.61K 88.3KB/s eta 12s kselftest.tar.xz 23%[===> ] 316.48K 89.8KB/s eta 12s kselftest.tar.xz 24%[===> ] 337.21K 86.4KB/s eta 12s kselftest.tar.xz 25%[====> ] 354.66K 86.4KB/s eta 12s kselftest.tar.xz 26%[====> ] 367.39K 83.7KB/s eta 12s kselftest.tar.xz 28%[====> ] 387.18K 82.8KB/s eta 12s kselftest.tar.xz 29%[====> ] 412.15K 80.6KB/s eta 12s kselftest.tar.xz 31%[=====> ] 435.26K 79.4KB/s eta 12s kselftest.tar.xz 32%[=====> ] 447.99K 78.3KB/s eta 12s kselftest.tar.xz 33%[=====> ] 459.30K 68.2KB/s eta 12s kselftest.tar.xz 34%[=====> ] 470.61K 65.7KB/s eta 12s kselftest.tar.xz 35%[======> ] 484.75K 65.8KB/s eta 12s kselftest.tar.xz 36%[======> ] 498.89K 64.9KB/s eta 12s kselftest.tar.xz 37%[======> ] 520.10K 63.5KB/s eta 12s kselftest.tar.xz 39%[======> ] 541.32K 63.6KB/s eta 11s kselftest.tar.xz 41%[=======> ] 569.11K 60.5KB/s eta 11s kselftest.tar.xz 43%[=======> ] 596.46K 64.7KB/s eta 11s kselftest.tar.xz 44%[=======> ] 612.95K 61.9KB/s eta 10s kselftest.tar.xz 46%[========> ] 636.06K 63.0KB/s eta 10s kselftest.tar.xz 48%[========> ] 661.51K 63.4KB/s eta 10s kselftest.tar.xz 49%[========> ] 678.48K 63.6KB/s eta 10s kselftest.tar.xz 50%[=========> ] 688.38K 61.0KB/s eta 10s kselftest.tar.xz 51%[=========> ] 706.76K 62.7KB/s eta 10s kselftest.tar.xz 52%[=========> ] 725.14K 62.0KB/s eta 10s kselftest.tar.xz 54%[=========> ] 744.94K 64.3KB/s eta 10s kselftest.tar.xz 55%[==========> ] 761.91K 65.7KB/s eta 8s kselftest.tar.xz 56%[==========> ] 783.12K 69.0KB/s eta 8s kselftest.tar.xz 58%[==========> ] 805.75K 70.4KB/s eta 8s kselftest.tar.xz 60%[===========> ] 828.37K 72.1KB/s eta 8s kselftest.tar.xz 62%[===========> ] 856.65K 74.9KB/s eta 8s kselftest.tar.xz 63%[===========> ] 880.21K 74.5KB/s eta 7s kselftest.tar.xz 66%[============> ] 908.49K 74.8KB/s eta 7s kselftest.tar.xz 67%[============> ] 925.94K 76.8KB/s eta 7s kselftest.tar.xz 69%[============> ] 949.50K 75.7KB/s eta 7s kselftest.tar.xz 70%[=============> ] 966.95K 75.9KB/s eta 5s kselftest.tar.xz 70%[=============> ] 975.43K 74.2KB/s eta 5s kselftest.tar.xz 71%[=============> ] 989.57K 75.4KB/s eta 5s kselftest.tar.xz 73%[=============> ] 1011K 78.1KB/s eta 5s kselftest.tar.xz 74%[=============> ] 1.00M 78.3KB/s eta 5s kselftest.tar.xz 76%[==============> ] 1.02M 80.7KB/s eta 4s kselftest.tar.xz 77%[==============> ] 1.04M 80.6KB/s eta 4s kselftest.tar.xz 78%[==============> ] 1.06M 81.5KB/s eta 4s kselftest.tar.xz 80%[===============> ] 1.08M 82.7KB/s eta 4s kselftest.tar.xz 82%[===============> ] 1.10M 81.7KB/s eta 3s kselftest.tar.xz 83%[===============> ] 1.13M 82.8KB/s eta 3s kselftest.tar.xz 85%[================> ] 1.15M 82.4KB/s eta 3s kselftest.tar.xz 87%[================> ] 1.18M 82.1KB/s eta 3s kselftest.tar.xz 89%[================> ] 1.20M 81.3KB/s eta 2s kselftest.tar.xz 91%[=================> ] 1.23M 81.0KB/s eta 2s kselftest.tar.xz 92%[=================> ] 1.24M 79.9KB/s eta 2s kselftest.tar.xz 93%[=================> ] 1.26M 78.0KB/s eta 2s kselftest.tar.xz 95%[==================> ] 1.28M 80.0KB/s eta 1s kselftest.tar.xz 97%[==================> ] 1.30M 81.9KB/s eta 1s kselftest.tar.xz 98%[==================> ] 1.33M 83.2KB/s eta 1s kselftest.tar.xz 100%[===================>] 1.34M 83.3KB/s in 18s 2023-05-30 16:06:04 (76.4 KB/s) - 'kselftest.tar.xz' saved [1408556/1408556] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== <12>[ 50.923609] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #