[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.38 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10723928/tftp-deploy-pkfgesv3/kernel/zImage tftp 0x10000000 10723928/tftp-deploy-pkfgesv3/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10723928/tftp-deploy-pkfgesv3/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 7.5 MiB/s done Bytes transferred = 9699840 (940200 hex) => tftp 0x14000000 10723928/tftp-deploy-pkfgesv3/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10723928/tftp-deploy-pkfgesv3/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10723928/tftp-deploy-pkfgesv3/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.7 MiB/s done Bytes transferred = 12149271 (b96217 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10723928/tftp-deploy-pkfgesv3/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10723928/tftp-deploy-pkfgesv3/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.38 Filename '10723928/tftp-deploy-pkfgesv3/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10723928/extract-nfsrootfs-29mmw_ac,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10723928/extract-nfsrootfs-29mmw_ac,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x940200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12149207 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.184-cip35 (KernelCI@build-j35243-arm-gcc-10-multi-v7-defconfig-vd9kd) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Jun 14 11:23:54 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10723928/extract-nfsrootfs-29mmw_ac,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 936492K/1048576K available (14336K kernel code, 2239K rwdata, 5356K rodata, 2048K init, 424K bss, 46548K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022291] Console: colour dummy device 80x30 <6>[ 0.024184] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034592] pid_max: default: 32768 minimum: 301 <6>[ 0.039629] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047046] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055662] CPU: Testing write buffer coherency: ok <6>[ 0.060160] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065727] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072094] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079809] rcu: Hierarchical SRCU implementation. <6>[ 0.086808] EFI services will not be available. <6>[ 0.089046] smp: Bringing up secondary CPUs ... <6>[ 0.094327] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094335] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105697] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105706] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116887] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116895] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127326] smp: Brought up 1 node, 4 CPUs <6>[ 0.131551] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.138009] CPU: All CPU(s) started in SVC mode. <6>[ 0.143432] devtmpfs: initialized <6>[ 0.153904] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.159251] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.169117] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179323] pinctrl core: initialized pinctrl subsystem <6>[ 0.183805] DMI not present or invalid. <6>[ 0.186919] NET: Registered protocol family 16 <6>[ 0.194225] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200876] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201063] cpuidle: using governor menu <6>[ 0.209154] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.390025] vdd1p1: supplied by regulator-dummy <6>[ 0.399223] vdd3p0: supplied by regulator-dummy <6>[ 0.408363] vdd2p5: supplied by regulator-dummy <6>[ 0.417517] vddarm: supplied by regulator-dummy <6>[ 0.426815] vddpu: supplied by regulator-dummy <6>[ 0.435761] vddsoc: supplied by regulator-dummy <6>[ 0.768462] No ATAGs? <6>[ 0.768651] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.776428] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.786609] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.796849] Serial: AMBA PL011 UART driver <6>[ 0.801010] printk: console [ramoops-1] enabled <6>[ 0.803349] pstore: Registered ramoops as persistent store backend <6>[ 0.809602] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.847378] iommu: Default domain type: Translated <6>[ 0.850126] vgaarb: loaded <5>[ 0.853518] SCSI subsystem initialized <6>[ 0.857228] usbcore: registered new interface driver usbfs <6>[ 0.862420] usbcore: registered new interface driver hub <6>[ 0.868001] usbcore: registered new device driver usb <6>[ 0.874798] i2c i2c-0: IMX I2C adapter registered <6>[ 0.879567] i2c i2c-1: IMX I2C adapter registered <6>[ 0.883981] i2c i2c-2: IMX I2C adapter registered <6>[ 0.889484] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.893343] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.902777] PTP clock support registered <6>[ 0.910507] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.972065] NET: Registered protocol family 2 <6>[ 1.974257] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.982671] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.990137] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.998208] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.005660] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.012363] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.019029] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.026510] NET: Registered protocol family 1 <6>[ 2.031610] RPC: Registered named UNIX socket transport module. <6>[ 2.037086] RPC: Registered udp transport module. <6>[ 2.042075] RPC: Registered tcp transport module. <6>[ 2.047002] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.053730] PCI: CLS 0 bytes, default 64 <6>[ 2.058355] Trying to unpack rootfs image as initramfs... <6>[ 3.019277] Freeing initrd memory: 11868K <4>[ 3.021202] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.028555] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.038306] Initialise system trusted keyrings <6>[ 3.041510] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.053745] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.057740] NFS: Registering the id_resolver key type <5>[ 3.062381] Key type id_resolver registered <5>[ 3.066736] Key type id_legacy registered <6>[ 3.071118] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.077960] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.085662] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.090718] Key type asymmetric registered <5>[ 3.094577] Asymmetric key parser 'x509' registered <6>[ 3.099752] bounce: pool size: 64 pages <6>[ 3.103850] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.111475] io scheduler mq-deadline registered <6>[ 3.116239] io scheduler kyber registered <6>[ 3.159762] mxs-dma 110000.dma-apbh: initialized <4>[ 3.166581] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.173514] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.229864] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.238071] SuperH (H)SCI(F) driver initialized <6>[ 3.241052] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.249883] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.257820] printk: console [ttymxc1] enabled <6>[ 3.257820] printk: console [ttymxc1] enabled <6>[ 3.266989] printk: bootconsole [ec_imx21] disabled <6>[ 3.266989] printk: bootconsole [ec_imx21] disabled <6>[ 3.278691] msm_serial: driver initialized <6>[ 3.284736] STMicroelectronics ASC driver initialized <6>[ 3.292023] STM32 USART driver initialized <4>[ 3.306794] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.314728] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.321566] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.338196] brd: module loaded <6>[ 3.351539] loop: module loaded <6>[ 3.358828] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.367058] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.375379] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.383841] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.391858] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.399594] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.407161] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.417764] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.425047] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.434124] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.444980] scsi host0: ahci-imx <6>[ 3.448853] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.469384] CAN device driver interface <6>[ 3.474835] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.484366] pps pps0: new PPS source ptp0 <6>[ 3.506653] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.514269] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.519504] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.525776] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.531462] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.543420] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.551150] usbcore: registered new interface driver pegasus <6>[ 3.557118] usbcore: registered new interface driver asix <6>[ 3.562847] usbcore: registered new interface driver ax88179_178a <6>[ 3.569240] usbcore: registered new interface driver cdc_ether <6>[ 3.575412] usbcore: registered new interface driver smsc75xx <6>[ 3.581491] usbcore: registered new interface driver smsc95xx <6>[ 3.587536] usbcore: registered new interface driver net1080 <6>[ 3.593511] usbcore: registered new interface driver cdc_subset <6>[ 3.599727] usbcore: registered new interface driver zaurus <6>[ 3.605650] usbcore: registered new interface driver cdc_ncm <6>[ 3.615136] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.621955] ehci-pci: EHCI PCI platform driver <6>[ 3.626704] ehci-platform: EHCI generic platform driver <6>[ 3.632508] ehci-orion: EHCI orion driver <6>[ 3.637006] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.641491] ehci-st: EHCI STMicroelectronics driver <6>[ 3.646818] ehci-exynos: EHCI Exynos driver <6>[ 3.651472] ehci-atmel: EHCI Atmel driver <6>[ 3.655927] tegra-ehci: Tegra EHCI driver <6>[ 3.660415] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.666896] ohci-pci: OHCI PCI platform driver <6>[ 3.671669] ohci-platform: OHCI generic platform driver <6>[ 3.677425] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.681922] ohci-st: OHCI STMicroelectronics driver <6>[ 3.687258] ohci-atmel: OHCI Atmel driver <6>[ 3.692804] usbcore: registered new interface driver usb-storage <6>[ 3.707254] i2c /dev entries driver <6>[ 3.730441] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.736921] sdhci: Copyright(c) Pierre Ossman <6>[ 3.744267] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.752528] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.759741] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.763963] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.765050] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.775792] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.783162] usbcore: registered new interface driver usbhid <6>[ 3.789004] usbhid: USB HID core driver <6>[ 3.799635] NET: Registered protocol family 10 <6>[ 3.802444] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.805430] Segment Routing with IPv6 <6>[ 3.807041] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.807463] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.810069] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.814073] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.821149] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.849030] NET: Registered protocol family 17 <6>[ 3.853781] can: controller area network core <6>[ 3.858482] NET: Registered protocol family 29 <6>[ 3.863218] can: raw protocol <6>[ 3.866457] can: broadcast manager protocol <6>[ 3.870933] can: netlink gateway - max_hops=1 <5>[ 3.875974] Key type dns_resolver registered <6>[ 3.882626] ThumbEE CPU extension supported. <5>[ 3.887177] Registering SWP/SWPB emulation handler <5>[ 3.892920] Loading compiled-in X.509 certificates <6>[ 3.903370] pstore: Using crash dump compression: deflate <4>[ 3.930992] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.938874] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.946919] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.963400] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.973393] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.978580] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.994759] mmc2: new high speed SDHC card at address aaaa <6>[ 4.001430] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <6>[ 4.010514] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.017054] hub 1-0:1.0: USB hub found <6>[ 4.021133] hub 1-0:1.0: 1 port detected <6>[ 4.028045] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.042776] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.044345] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.050488] GPT:7812499 != 31116287 <4>[ 4.058371] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.061990] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.061995] GPT:7812499 != 31116287 <4>[ 4.062001] GPT: Use GNU Parted to correct GPT errors. <4>[ 4.069911] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.074759] mmcblk2: p1 p2 p3 <4>[ 4.082678] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.103027] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.111040] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.123191] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.131087] panel-simple panel-lcd: Specify missing connector_type <6>[ 4.139477] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.148850] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.161241] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.169124] panel-simple panel-lcd: Specify missing connector_type <6>[ 4.181373] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.390572] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.592117] hub 1-1:1.0: USB hub found <6>[ 4.596345] hub 1-1:1.0: 3 ports detected <4>[ 4.603461] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.616762] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.624747] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.281023] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.310624] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.340549] Sending DHCP requests ., OK <6>[ 7.384719] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.38 <6>[ 7.393042] IP-Config: Complete: <6>[ 7.396565] device=eth0, hwaddr=00:19:b8:08:f0:fe, ipaddr=192.168.201.38, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.407323] host=imx6q-sabrelite-lava-cbg-8, domain=lava-rack, nis-domain=(none) <6>[ 7.415467] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.415480] nameserver0=192.168.201.1 <6>[ 7.434775] Freeing unused kernel memory: 2048K <6>[ 7.481513] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 8.299043] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.323046] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.337722] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.341743] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.345698] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.382572] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.390835] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.399454] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 8.405528] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.408059] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.415819] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.424259] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.490624] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.517636] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.525450] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.546684] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.612841] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.628976] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 8.636177] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 8.637116] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <6>[ 8.643758] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <4>[ 8.652350] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 8.660541] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 8.666649] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.673596] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.685501] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.685506] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.685516] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.713860] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.722732] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.729187] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.737808] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.747705] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.756293] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.764852] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.773395] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.783607] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.791633] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.800597] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.825231] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.833876] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.842449] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.851009] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.125554] caam algorithms registered in /proc/crypto <6>[ 9.132747] caam 2100000.crypto: registering rng-caam <4>[ 9.140005] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.148350] panel-simple panel-lcd: Specify missing connector_type Begin: Loading essential drivers ... done. <4>[ 9.158145] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done<6>[ 9.174971] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) . Begin: Running /scripts/nfs-pr<6>[ 9.186170] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) emount ... Waiting up to 60 secs <6>[ 9.197586] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) for any ethernet to become availa<6>[ 9.208812] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) ble Device /sys/class/net/eth0 f<4>[ 9.222085] panel-simple panel-lcd: supply power not found, using dummy regulator ound done. <4>[ 9.230975] panel-simple panel-lcd: Specify missing connector_type <5>[ 9.320523] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f0:fe mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.38 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-8 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.230296] systemd[1]: System time before build time, advancing clock. <30>[ 10.280430] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.304537] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.342738] systemd[1]: Set hostname to . <30>[ 11.083931] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.093514] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.106324] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.115906] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.161938] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.202020] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.241024] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.281359] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.321481] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.360848] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.373130] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.411371] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.440962] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 11.480676] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 11.511064] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 11.541866] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 11.623437] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 11.633354] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 11.672077] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 11.722827] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 11.763621] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 11.802169] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 11.841708] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 11.851259] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 11.863799] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 11.904521] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 11.944852] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 11.984139] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 12.024179] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 12.064255] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.105568] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.121620] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.168423] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.204893] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.244093] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.299528] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.351219] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.401819] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.466327] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 12.779944] systemd-journald[273]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Create Volatile Files and Directories. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.184-cip35 #1 SMP Wed Jun 14 11:23:54 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10723928/extract-nfsrootfs-29mmw_ac' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10723928/extract-nfsrootfs-29mmw_ac' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-10723928/environment . /lava-10723928/environment / # /lava-10723928/bin/lava-test-runner /lava-10723928/0 /lava-10723928/bin/lava-test-runner /lava-10723928/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-10723928/0/tests/0_timesync-off ++ cat uuid + UUID=10723928_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-10723928/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=10723928_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.182-cip35-191-gf4efde512959/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-06-14 11:46:03-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.182-cip35-191-gf4efde512959/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1408712 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 43.08K 166KB/s kselftest.tar.xz 6%[> ] 95.40K 185KB/s kselftest.tar.xz 11%[=> ] 162.35K 209KB/s kselftest.tar.xz 14%[=> ] 197.70K 191KB/s kselftest.tar.xz 17%[==> ] 235.88K 182KB/s kselftest.tar.xz 19%[==> ] 273.57K 176KB/s kselftest.tar.xz 22%[===> ] 308.00K 170KB/s kselftest.tar.xz 24%[===> ] 341.93K 165KB/s kselftest.tar.xz 27%[====> ] 380.11K 163KB/s kselftest.tar.xz 30%[=====> ] 425.36K 164KB/s kselftest.tar.xz 34%[=====> ] 469.20K 167KB/s kselftest.tar.xz 37%[======> ] 514.45K 168KB/s eta 5s kselftest.tar.xz 40%[=======> ] 556.87K 167KB/s eta 5s kselftest.tar.xz 43%[=======> ] 603.53K 168KB/s eta 5s kselftest.tar.xz 47%[========> ] 653.03K 170KB/s eta 5s kselftest.tar.xz 51%[=========> ] 702.03K 168KB/s eta 4s kselftest.tar.xz 54%[=========> ] 747.28K 168KB/s eta 4s kselftest.tar.xz 56%[==========> ] 777.46K 167KB/s eta 4s kselftest.tar.xz 58%[==========> ] 804.33K 165KB/s eta 4s kselftest.tar.xz 60%[===========> ] 838.27K 161KB/s eta 4s kselftest.tar.xz 63%[===========> ] 872.21K 155KB/s eta 3s kselftest.tar.xz 66%[============> ] 908.97K 154KB/s eta 3s kselftest.tar.xz 68%[============> ] 948.57K 155KB/s eta 3s kselftest.tar.xz 72%[=============> ] 990.99K 158KB/s eta 3s kselftest.tar.xz 74%[=============> ] 1.00M 156KB/s eta 2s kselftest.tar.xz 76%[==============> ] 1.03M 152KB/s eta 2s kselftest.tar.xz 78%[==============> ] 1.05M 143KB/s eta 2s kselftest.tar.xz 79%[==============> ] 1.07M 137KB/s eta 2s kselftest.tar.xz 80%[===============> ] 1.08M 134KB/s eta 2s kselftest.tar.xz 82%[===============> ] 1.10M 128KB/s eta 2s kselftest.tar.xz 83%[===============> ] 1.12M 121KB/s eta 2s kselftest.tar.xz 85%[================> ] 1.15M 117KB/s eta 2s kselftest.tar.xz 87%[================> ] 1.17M 113KB/s eta 1s kselftest.tar.xz 89%[================> ] 1.20M 112KB/s eta 1s kselftest.tar.xz 90%[=================> ] 1.22M 108KB/s eta 1s kselftest.tar.xz 92%[=================> ] 1.24M 109KB/s eta 1s kselftest.tar.xz 93%[=================> ] 1.25M 103KB/s eta 1s kselftest.tar.xz 95%[==================> ] 1.28M 102KB/s eta 0s kselftest.tar.xz 96%[==================> ] 1.30M 97.4KB/s eta 0s kselftest.tar.xz 98%[==================> ] 1.32M 95.9KB/s eta 0s kselftest.tar.xz 100%[===================>] 1.34M 92.6KB/s in 10s 2023-06-14 11:46:13 (133 KB/s) - 'kselftest.tar.xz' saved [1408712/1408712] skiplist: ======================================== ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== <12>[ 42.572333] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #