Trying 0.0.0.0... Connected to 0. Escape character is '^]'. U-Boot SPL 2021.10 (Oct 25 2021 - 13:39:59 +0200) Trying to boot from SPI U-Boot 2021.10 (Oct 25 2021 - 13:39:59 +0200) SoC: LS1028A Rev1.0 (0x870b0110) Clock Configuration: CPU0(A72):1300 MHz CPU1(A72):1300 MHz Bus: 400 MHz DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 34004010 00000030 00000000 00000000 00000010: 00000000 008f0000 0030c000 00000000 00000020: 06200000 00002580 00000000 00019016 00000030: 00000000 00000048 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000304 00000000 000e7000 00000000 00000070: bb580000 00020000 Model: Kontron SMARC-sAL28 (Dual PHY) EL: 3 DRAM: 4 GiB DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on) SEC0: RNG instantiated CPU: 2 cores online Using SERDES1 Protocol: 47960 (0xbb58) MMC: FSL_SDHC: 1, FSL_SDHC: 0 Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 64 KiB, total 4 MiB OK PCIe1: pcie@3400000 Root Complex: no link PCIe2: pcie@3500000 Root Complex: no link In: serial@21c0500 Out: serial@21c0500 Err: serial@21c0500 Net: eth0: enetc-0, eth1: enetc-1 Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => dhcp dhcp enetc-0 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.0.112 (1255 ms) => setenv serverip 10.228.65.1 setenv serverip 10.228.65.1 => tftp 0x82000000 356911/tftp-deploy-li8x06zh/kernel/Image tftp 0x82000000 356911/tftp-deploy-li8x06zh/kernel/Image Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.112; sending through gateway 172.16.0.254 Filename '356911/tftp-deploy-li8x06zh/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 9.8 MiB/s done Bytes transferred = 43872768 (29d7200 hex) => tftp 0x90080000 356911/tftp-deploy-li8x06zh/ramdisk/ramdisk.cpio.gz.uboot tftp 0x90080000 356911/tftp-deploy-li8x06zh/ramdisk/ramdisk.cpio.gz.uboot Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.112; sending through gateway 172.16.0.254 Filename '356911/tftp-deploy-li8x06zh/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x90080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################## 14.8 MiB/s done Bytes transferred = 21366218 (14605ca hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 356911/tftp-deploy-li8x06zh/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb tftp 0x90000000 356911/tftp-deploy-li8x06zh/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb Using enetc-0 device TFTP from server 10.228.65.1; our IP address is 172.16.0.112; sending through gateway 172.16.0.254 Filename '356911/tftp-deploy-li8x06zh/dtb/fsl-ls1028a-kontron-kbox-a-230-ls.dtb'. Load address: 0x90000000 Loading: *## 6 MiB/s done Bytes transferred = 25056 (61e0 hex) => setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => booti 0x82000000 0x90080000 0x90000000 booti 0x82000000 0x90080000 0x90000000 ## Loading init Ramdisk from Legacy Image at 90080000 ... Image Name: Created: 2023-06-14 2:25:41 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 21366154 Bytes = 20.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Using Device Tree in place at 0000000090000000, end 00000000900091df WARNING could not find node fsl,ls1028a-gpu: FDT_ERR_NOTFOUND. Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd083] [ 0.000000] Linux version 5.10.182-cip35 (KernelCI@build-j33139-arm64-gcc-10-defconfig-kselftest-prwf9) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Wed Jun 14 01:59:43 UTC 2023 [ 0.000000] Machine model: Kontron KBox A-230-LS [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ns16550a0 at MMIO 0x00000000021c0500 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550a0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x20ff7db7c0-0x20ff7ddfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000020ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] node 0: [mem 0x0000002080000000-0x00000020ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000020ffffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fcc00000 [ 0.000000] percpu: Embedded 34 pages/cpu s101008 r8192 d30064 u139264 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1032192 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlycon n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000f8c00000-0x00000000fcc00000] (64MB) <6>[ 0.000000] Memory: 3940264K/4194304K available (18880K kernel code, 4572K rwdata, 9504K rodata, 9792K init, 11276K bss, 221272K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 59229 entries in 232 pages <6>[ 0.000000] ftrace: allocated 232 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=2. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 256 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006040000 <6>[ 0.000000] ITS [mem 0x06020000-0x0603ffff] <6>[ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @2080200000 (flat, esz 8, psz 64K, shr 0) <6>[ 0.000000] ITS: using cache flushing for cmd queue <6>[ 0.000000] GICv3: using LPI property table @0x00000020801e0000 <6>[ 0.000000] GIC: using cache flushing for LPI property table <6>[ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x00000020801f0000 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c40939b5, max_idle_ns: 440795202646 ns <6>[ 0.000003] sched_clock: 56 bits at 25MHz, resolution 40ns, wraps every 4398046511100ns <6>[ 0.008810] Console: colour dummy device 80x25 <4>[ 0.013587] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.021684] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.026095] ... MAX_LOCK_DEPTH: 48 <4>[ 0.030592] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.035265] ... CLASSHASH_SIZE: 4096 <4>[ 0.039937] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.044697] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.049457] ... CHAINHASH_SIZE: 32768 <4>[ 0.054217] memory used by lock dependency info: 6365 kB <4>[ 0.059943] memory used for stack traces: 4224 kB <4>[ 0.065053] per task-struct memory footprint: 1920 bytes <6>[ 0.070858] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) <6>[ 0.081599] pid_max: default: 32768 minimum: 301 <6>[ 0.086669] LSM: Security Framework initializing <6>[ 0.091638] LSM support for eBPF active <6>[ 0.095860] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.103635] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.115648] rcu: Hierarchical SRCU implementation. <6>[ 0.123234] Platform MSI: gic-its@6020000 domain created <6>[ 0.129115] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created <6>[ 0.137064] fsl-mc MSI: gic-its@6020000 domain created <6>[ 0.143168] EFI services will not be available. <6>[ 0.148437] smp: Bringing up secondary CPUs ... <6>[ 0.154624] Detected PIPT I-cache on CPU1 <6>[ 0.154646] GICv3: CPU1: found redistributor 1 region 0:0x0000000006060000 <6>[ 0.154655] GICv3: CPU1: using allocated LPI pending table @0x0000002080280000 <6>[ 0.154698] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] <6>[ 0.155097] smp: Brought up 1 node, 2 CPUs <6>[ 0.185536] SMP: Total of 2 processors activated. <6>[ 0.190575] CPU features: detected: 32-bit EL0 Support <6>[ 0.196110] CPU features: detected: CRC32 instructions <6>[ 0.201597] CPU features: detected: 32-bit EL1 Support <6>[ 0.235916] CPU: All CPU(s) started at EL2 <6>[ 0.240391] alternatives: patching kernel code <6>[ 0.247116] devtmpfs: initialized <4>[ 0.263950] KASLR disabled due to lack of seed <6>[ 0.269843] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.279992] futex hash table entries: 512 (order: 4, 65536 bytes, linear) <6>[ 0.288161] pinctrl core: initialized pinctrl subsystem <6>[ 0.296439] DMI not present or invalid. <6>[ 0.301586] NET: Registered protocol family 16 <6>[ 0.309501] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.317058] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.325578] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.333970] audit: initializing netlink subsys (disabled) <5>[ 0.340016] audit: type=2000 audit(0.228:1): state=initialized audit_enabled=0 res=1 <6>[ 0.342023] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.348139] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.355276] cpuidle: using governor menu <6>[ 0.366694] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.373921] ASID allocator initialised with 65536 entries <6>[ 0.382056] Serial: AMBA PL011 UART driver <6>[ 0.436778] Machine: Kontron KBox A-230-LS <6>[ 0.441207] SoC family: QorIQ LS1028A <6>[ 0.445170] SoC ID: svr:0x870b0110, Revision: 1.0 <6>[ 0.489701] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.496777] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.503833] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.510883] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.520995] cryptd: max_cpu_qlen set to 1000 <6>[ 0.531131] ACPI: Interpreter disabled. <6>[ 0.539243] iommu: Default domain type: Translated <6>[ 0.545172] vgaarb: loaded <5>[ 0.549003] SCSI subsystem initialized <6>[ 0.553921] usbcore: registered new interface driver usbfs <6>[ 0.559872] usbcore: registered new interface driver hub <6>[ 0.565590] usbcore: registered new device driver usb <6>[ 0.571965] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.581108] i2c i2c-0: IMX I2C adapter registered <6>[ 0.587245] imx-i2c 2030000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.595394] i2c i2c-1: IMX I2C adapter registered <6>[ 0.600892] imx-i2c 2040000.i2c: can't get pinctrl, bus recovery not supported <6>[ 0.608996] i2c i2c-2: IMX I2C adapter registered <6>[ 0.614747] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.620045] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.629620] PTP clock support registered <6>[ 0.634124] EDAC MC: Ver: 3.0.0 <6>[ 0.640606] FPGA manager framework <6>[ 0.644574] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.652713] clocksource: Switched to clocksource arch_sys_counter <5>[ 1.388056] VFS: Disk quotas dquot_6.6.0 <6>[ 1.392407] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 1.400258] pnp: PnP ACPI: disabled <6>[ 1.420346] NET: Registered protocol family 2 <6>[ 1.425410] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 1.435533] tcp_listen_portaddr_hash hash table entries: 2048 (order: 5, 163840 bytes, linear) <6>[ 1.444860] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 1.453745] TCP bind hash table entries: 32768 (order: 9, 2359296 bytes, linear) <6>[ 1.466031] TCP: Hash tables configured (established 32768 bind 32768) <6>[ 1.473572] MPTCP token hash table entries: 4096 (order: 6, 360448 bytes, linear) <6>[ 1.482108] UDP hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.489878] UDP-Lite hash table entries: 2048 (order: 6, 327680 bytes, linear) <6>[ 1.498270] NET: Registered protocol family 1 <6>[ 1.504105] RPC: Registered named UNIX socket transport module. <6>[ 1.510419] RPC: Registered udp transport module. <6>[ 1.515541] RPC: Registered tcp transport module. <6>[ 1.520579] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.527380] NET: Registered protocol family 44 <6>[ 1.532167] PCI: CLS 0 bytes, default 64 <6>[ 1.537002] Unpacking initramfs... <6>[ 2.678097] Freeing initrd memory: 20860K <6>[ 2.683296] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available <6>[ 2.692167] kvm [1]: IPA Size Limit: 44 bits <6>[ 2.703266] kvm [1]: GICv3: no GICV resource entry <6>[ 2.708396] kvm [1]: disabling GICv2 emulation <6>[ 2.713200] kvm [1]: GIC system register CPU interface enabled <6>[ 2.719490] kvm [1]: vgic interrupt IRQ9 <6>[ 2.723894] kvm [1]: Hyp mode initialized successfully <5>[ 2.734027] Initialise system trusted keyrings <6>[ 2.739176] workingset: timestamp_bits=42 max_order=20 bucket_order=0 <6>[ 2.770440] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.778122] NFS: Registering the id_resolver key type <5>[ 2.783574] Key type id_resolver registered <5>[ 2.788097] Key type id_legacy registered <6>[ 2.792682] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 2.799768] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 2.807825] 9p: Installing v9fs 9p2000 file system support <5>[ 2.844874] Key type asymmetric registered <5>[ 2.849338] Asymmetric key parser 'x509' registered <6>[ 2.854631] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 2.862407] io scheduler mq-deadline registered <6>[ 2.867268] io scheduler kyber registered <4>[ 2.871964] test_firmware: interface ready <6>[ 2.896788] pci-host-generic 1f0000000.pcie: host bridge /soc/pcie@1f0000000 ranges: <6>[ 2.904980] pci-host-generic 1f0000000.pcie: MEM 0x01f8000000..0x01f815ffff -> 0x0000000000 <6>[ 2.914204] pci-host-generic 1f0000000.pcie: MEM 0x01f8160000..0x01f81cffff -> 0x0000000000 <6>[ 2.923432] pci-host-generic 1f0000000.pcie: MEM 0x01f81d0000..0x01f81effff -> 0x0000000000 <6>[ 2.932655] pci-host-generic 1f0000000.pcie: MEM 0x01f81f0000..0x01f820ffff -> 0x0000000000 <6>[ 2.941887] pci-host-generic 1f0000000.pcie: MEM 0x01f8210000..0x01f822ffff -> 0x0000000000 <6>[ 2.951109] pci-host-generic 1f0000000.pcie: MEM 0x01f8230000..0x01f824ffff -> 0x0000000000 <6>[ 2.960301] pci-host-generic 1f0000000.pcie: MEM 0x01fc000000..0x01fc3fffff -> 0x0000000000 <6>[ 2.969591] pci-host-generic 1f0000000.pcie: ECAM at [mem 0x1f0000000-0x1f00fffff] for [bus 00] <6>[ 2.978971] pci-host-generic 1f0000000.pcie: PCI host bridge to bus 0000:00 <6>[ 2.986298] pci_bus 0000:00: root bus resource [bus 00] <6>[ 2.991983] pci_bus 0000:00: root bus resource [mem 0x1f8000000-0x1f815ffff] (bus address [0x00000000-0x0015ffff]) <6>[ 3.002755] pci_bus 0000:00: root bus resource [mem 0x1f8160000-0x1f81cffff pref] (bus address [0x00000000-0x0006ffff]) <6>[ 3.013938] pci_bus 0000:00: root bus resource [mem 0x1f81d0000-0x1f81effff] (bus address [0x00000000-0x0001ffff]) <6>[ 3.024683] pci_bus 0000:00: root bus resource [mem 0x1f81f0000-0x1f820ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 3.035882] pci_bus 0000:00: root bus resource [mem 0x1f8210000-0x1f822ffff] (bus address [0x00000000-0x0001ffff]) <6>[ 3.046625] pci_bus 0000:00: root bus resource [mem 0x1f8230000-0x1f824ffff pref] (bus address [0x00000000-0x0001ffff]) <6>[ 3.057805] pci_bus 0000:00: root bus resource [mem 0x1fc000000-0x1fc3fffff] (bus address [0x00000000-0x003fffff]) <6>[ 3.068641] pci 0000:00:00.0: [1957:e100] type 00 class 0x020001 <6>[ 3.075161] pci 0000:00:00.0: BAR 0: [mem 0x1f8000000-0x1f803ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.085999] pci 0000:00:00.0: BAR 2: [mem 0x1f8160000-0x1f816ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.097273] pci 0000:00:00.0: VF BAR 0: [mem 0x1f81d0000-0x1f81dffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 3.108381] pci 0000:00:00.0: VF BAR 2: [mem 0x1f81f0000-0x1f81fffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 3.119992] pci 0000:00:00.0: PME# supported from D0 D3hot <6>[ 3.125884] pci 0000:00:00.0: VF(n) BAR0 space: [mem 0x1f81d0000-0x1f81effff 64bit] (contains BAR0 for 2 VFs) <6>[ 3.136187] pci 0000:00:00.0: VF(n) BAR2 space: [mem 0x1f81f0000-0x1f820ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 3.147581] pci 0000:00:00.1: [1957:e100] type 00 class 0x020001 <6>[ 3.154080] pci 0000:00:00.1: BAR 0: [mem 0x1f8040000-0x1f807ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.164918] pci 0000:00:00.1: BAR 2: [mem 0x1f8170000-0x1f817ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.176193] pci 0000:00:00.1: VF BAR 0: [mem 0x1f8210000-0x1f821ffff 64bit] (from Enhanced Allocation, properties 0x4) <6>[ 3.187300] pci 0000:00:00.1: VF BAR 2: [mem 0x1f8230000-0x1f823ffff 64bit pref] (from Enhanced Allocation, properties 0x3) <6>[ 3.198913] pci 0000:00:00.1: PME# supported from D0 D3hot <6>[ 3.204773] pci 0000:00:00.1: VF(n) BAR0 space: [mem 0x1f8210000-0x1f822ffff 64bit] (contains BAR0 for 2 VFs) <6>[ 3.215085] pci 0000:00:00.1: VF(n) BAR2 space: [mem 0x1f8230000-0x1f824ffff 64bit pref] (contains BAR2 for 2 VFs) <6>[ 3.226466] pci 0000:00:00.2: [1957:e100] type 00 class 0x020001 <6>[ 3.232938] pci 0000:00:00.2: BAR 0: [mem 0x1f8080000-0x1f80bffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.243774] pci 0000:00:00.2: BAR 2: [mem 0x1f8180000-0x1f818ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.255126] pci 0000:00:00.2: PME# supported from D0 D3hot <6>[ 3.261484] pci 0000:00:00.3: [1957:ee01] type 00 class 0x088001 <6>[ 3.267978] pci 0000:00:00.3: BAR 0: [mem 0x1f8100000-0x1f811ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.278814] pci 0000:00:00.3: BAR 2: [mem 0x1f8190000-0x1f819ffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.290154] pci 0000:00:00.3: PME# supported from D0 D3hot <6>[ 3.296522] pci 0000:00:00.4: [1957:ee02] type 00 class 0x088001 <6>[ 3.302991] pci 0000:00:00.4: BAR 0: [mem 0x1f8120000-0x1f813ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.313836] pci 0000:00:00.4: BAR 2: [mem 0x1f81a0000-0x1f81affff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.325186] pci 0000:00:00.4: PME# supported from D0 D3hot <6>[ 3.331552] pci 0000:00:00.5: [1957:eef0] type 00 class 0x020801 <6>[ 3.338023] pci 0000:00:00.5: BAR 0: [mem 0x1f8140000-0x1f815ffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.348859] pci 0000:00:00.5: BAR 2: [mem 0x1f81b0000-0x1f81bffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.360132] pci 0000:00:00.5: BAR 4: [mem 0x1fc000000-0x1fc3fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.371032] pci 0000:00:00.5: PME# supported from D0 D3hot <6>[ 3.377458] pci 0000:00:00.6: [1957:e100] type 00 class 0x020001 <6>[ 3.383929] pci 0000:00:00.6: BAR 0: [mem 0x1f80c0000-0x1f80fffff 64bit] (from Enhanced Allocation, properties 0x0) <6>[ 3.394764] pci 0000:00:00.6: BAR 2: [mem 0x1f81c0000-0x1f81cffff 64bit pref] (from Enhanced Allocation, properties 0x1) <6>[ 3.406105] pci 0000:00:00.6: PME# supported from D0 D3hot <6>[ 3.413233] pci 0000:00:1f.0: [1957:e001] type 00 class 0x080700 <6>[ 3.419795] OF: /soc/pcie@1f0000000: no msi-map translation for id 0xf8 on (null) <6>[ 3.428243] OF: /soc/pcie@1f0000000: no iommu-map translation for id 0xf8 on (null) <3>[ 3.436349] pcieport 0000:00:1f.0: of_irq_parse_pci: failed with rc=-22 <6>[ 3.444681] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: <6>[ 3.452442] layerscape-pcie 3400000.pcie: IO 0x8000010000..0x800001ffff -> 0x0000000000 <6>[ 3.461422] layerscape-pcie 3400000.pcie: MEM 0x8040000000..0x807fffffff -> 0x0040000000 <6>[ 3.470644] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0001:00 <6>[ 3.477705] pci_bus 0001:00: root bus resource [bus 00-ff] <6>[ 3.483533] pci_bus 0001:00: root bus resource [io 0x0000-0xffff] <6>[ 3.490065] pci_bus 0001:00: root bus resource [mem 0x8040000000-0x807fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.501040] pci 0001:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.507586] pci 0001:00:00.0: supports D1 D2 <6>[ 3.512184] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.520509] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.527491] pci 0001:00:00.0: PCI bridge to [bus 01] <6>[ 3.533390] layerscape-pcie 3500000.pcie: host bridge /soc/pcie@3500000 ranges: <6>[ 3.541152] layerscape-pcie 3500000.pcie: IO 0x8800010000..0x880001ffff -> 0x0000000000 <6>[ 3.550092] layerscape-pcie 3500000.pcie: MEM 0x8840000000..0x887fffffff -> 0x0040000000 <6>[ 3.559317] layerscape-pcie 3500000.pcie: PCI host bridge to bus 0002:00 <6>[ 3.566388] pci_bus 0002:00: root bus resource [bus 00-ff] <6>[ 3.572217] pci_bus 0002:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) <6>[ 3.581555] pci_bus 0002:00: root bus resource [mem 0x8840000000-0x887fffffff] (bus address [0x40000000-0x7fffffff]) <6>[ 3.592516] pci 0002:00:00.0: [1957:82c1] type 01 class 0x060400 <6>[ 3.599065] pci 0002:00:00.0: supports D1 D2 <6>[ 3.603663] pci 0002:00:00.0: PME# supported from D0 D1 D2 D3hot <6>[ 3.611962] pci_bus 0002:01: busn_res: [bus 01-ff] end is updated to 01 <6>[ 3.618941] pci 0002:00:00.0: PCI bridge to [bus 01] <4>[ 3.627679] EINJ: ACPI disabled. <6>[ 3.662112] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 3.675971] printk: console [ttyS0] disabled <6>[ 3.680812] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 3.690188] printk: console [ttyS0] enabled <6>[ 3.690188] printk: console [ttyS0] enabled <6>[ 3.699177] printk: bootconsole [ns16550a0] disabled <6>[ 3.699177] printk: bootconsole [ns16550a0] disabled <6>[ 3.711593] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 23, base_baud = 12500000) is a 16550A <6>[ 3.721825] SuperH (H)SCI(F) driver initialized <6>[ 3.727614] msm_serial: driver initialized <6>[ 3.733183] 2270000.serial: ttyLP2 at MMIO 0x2270000 (irq = 24, base_baud = 12500000) is a FSL_LPUART <5>[ 3.748199] arm-smmu 5000000.iommu: probing hardware configuration... <5>[ 3.754980] arm-smmu 5000000.iommu: SMMUv2 with: <5>[ 3.759903] arm-smmu 5000000.iommu: stage 1 translation <5>[ 3.765520] arm-smmu 5000000.iommu: stage 2 translation <5>[ 3.771136] arm-smmu 5000000.iommu: nested translation <5>[ 3.776671] arm-smmu 5000000.iommu: stream matching with 128 register groups <5>[ 3.784127] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) <5>[ 3.790970] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 <5>[ 3.797721] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA <5>[ 3.804471] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA <6>[ 3.833238] loop: module loaded <6>[ 3.837831] lkdtm: No crash points registered, enable through debugfs <6>[ 3.866958] megasas: 07.714.04.00-rc1 <6>[ 3.881354] spi-nor spi0.0: w25q32dw (4096 Kbytes) <5>[ 3.900057] 8 fixed-partitions partitions found on MTD device 20c0000.spi <5>[ 3.907228] Creating 8 MTD partitions on \"20c0000.spi\": <5>[ 3.912767] 0x000000000000-0x000000010000 : \"rcw\" <5>[ 3.923093] 0x000000010000-0x000000100000 : \"failsafe bootloader\" <5>[ 3.934863] 0x000000100000-0x000000140000 : \"failsafe DP firmware\" <5>[ 3.946861] 0x000000140000-0x0000001e0000 : \"failsafe trusted firmware\" <5>[ 3.958849] 0x0000001e0000-0x000000200000 : \"reserved\" <5>[ 3.970843] 0x000000200000-0x000000210000 : \"configuration store\" <5>[ 3.982875] 0x000000210000-0x0000003e0000 : \"bootloader\" <5>[ 3.994829] 0x0000003e0000-0x000000400000 : \"bootloader environment\" <6>[ 4.015415] thunder_xcv, ver 1.0 <6>[ 4.019060] thunder_bgx, ver 1.0 <6>[ 4.022698] nicpf, ver 1.0 <6>[ 4.027758] fsl_enetc 0000:00:00.0: Adding to iommu group 0 <6>[ 4.140758] fsl_enetc 0000:00:00.0: enabling device (0400 -> 0402) <6>[ 4.147385] fsl_enetc 0000:00:00.0: no MAC address specified for SI1, using 52:ac:f4:07:a2:b1 <6>[ 4.156240] fsl_enetc 0000:00:00.0: no MAC address specified for SI2, using 6e:13:2a:20:d7:8b <6>[ 4.186941] fsl_enetc 0000:00:00.1: Adding to iommu group 1 <6>[ 4.300748] fsl_enetc 0000:00:00.1: enabling device (0400 -> 0402) <6>[ 4.307351] fsl_enetc 0000:00:00.1: no MAC address specified for SI1, using ca:9e:4e:6d:42:86 <6>[ 4.316207] fsl_enetc 0000:00:00.1: no MAC address specified for SI2, using 2e:3f:79:53:3d:92 <6>[ 4.345995] fsl_enetc 0000:00:00.2: Adding to iommu group 2 <6>[ 4.456748] fsl_enetc 0000:00:00.2: enabling device (0400 -> 0402) <6>[ 4.463351] fsl_enetc 0000:00:00.2: no MAC address specified for SI0, using 02:6f:c1:ce:99:47 <6>[ 4.475703] fsl_enetc 0000:00:00.6: Adding to iommu group 3 <6>[ 4.588758] fsl_enetc 0000:00:00.6: enabling device (0400 -> 0402) <6>[ 4.596206] fsl_enetc 0000:00:00.6: device is disabled, skipping <6>[ 4.603061] fsl_enetc_mdio 0000:00:00.3: Adding to iommu group 4 <6>[ 4.716750] fsl_enetc_mdio 0000:00:00.3: enabling device (0400 -> 0402) <6>[ 4.775716] fsl_enetc_ptp 0000:00:00.4: Adding to iommu group 5 <6>[ 4.782283] fsl_enetc_ptp 0000:00:00.4: enabling device (0404 -> 0406) <4>[ 4.789493] ptp_qoriq: device tree node missing required elements, try automatic configuration <6>[ 4.798904] pps pps0: new PPS source ptp0 <6>[ 4.804927] hclge is initializing <6>[ 4.808593] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 4.816172] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 4.821920] e1000: Intel(R) PRO/1000 Network Driver <6>[ 4.827104] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 4.833281] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.838550] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.844901] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.850606] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.856571] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 4.863147] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 4.870195] sky2: driver version 1.30 <6>[ 4.876559] VFIO - User Level meta-driver version: 0.3 <6>[ 4.883275] dwc3 3100000.usb: Adding to iommu group 6 <6>[ 4.890791] dwc3 3110000.usb: Adding to iommu group 7 <6>[ 4.900953] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.907839] ehci-pci: EHCI PCI platform driver <6>[ 4.912671] ehci-platform: EHCI generic platform driver <6>[ 4.918457] ehci-orion: EHCI orion driver <6>[ 4.923007] ehci-exynos: EHCI Exynos driver <6>[ 4.927719] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.934269] ohci-pci: OHCI PCI platform driver <6>[ 4.939106] ohci-platform: OHCI generic platform driver <6>[ 4.944902] ohci-exynos: OHCI Exynos driver <6>[ 4.950260] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.956209] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 4.964546] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 4.974361] xhci-hcd xhci-hcd.0.auto: irq 28, io mem 0x03100000 <6>[ 4.981168] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 4.986983] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 4.994984] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 5.003760] hub 1-0:1.0: USB hub found <6>[ 5.007984] hub 1-0:1.0: 1 port detected <6>[ 5.013389] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 5.023148] hub 2-0:1.0: USB hub found <6>[ 5.027268] hub 2-0:1.0: 1 port detected <6>[ 5.032526] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 5.038471] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 <6>[ 5.046908] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 <6>[ 5.056751] xhci-hcd xhci-hcd.1.auto: irq 29, io mem 0x03110000 <6>[ 5.063562] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller <6>[ 5.069374] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 <6>[ 5.077375] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed <6>[ 5.085598] hub 3-0:1.0: USB hub found <6>[ 5.089742] hub 3-0:1.0: 1 port detected <6>[ 5.094825] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 5.104505] hub 4-0:1.0: USB hub found <6>[ 5.108623] hub 4-0:1.0: 1 port detected <6>[ 5.114396] usbcore: registered new interface driver usb-storage <6>[ 5.127077] i2c /dev entries driver <6>[ 5.142235] sp805-wdt c000000.watchdog: registration successful <6>[ 5.148974] sp805-wdt c010000.watchdog: registration successful <6>[ 5.160306] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver <6>[ 5.171669] sdhci: Secure Digital Host Controller Interface driver <6>[ 5.178739] sdhci: Copyright(c) Pierre Ossman <6>[ 5.184630] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.193502] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 5.201177] sdhci-esdhc 2140000.mmc: Adding to iommu group 8 <6>[ 5.203568] sdhci-esdhc 2150000.mmc: Adding to iommu group 9 <6>[ 5.207269] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.223382] usbcore: registered new interface driver usbhid <6>[ 5.229276] usbhid: USB HID core driver <6>[ 5.240875] mmc1: SDHCI controller on 2140000.mmc [2140000.mmc] using ADMA <6>[ 5.243892] mmc0: SDHCI controller on 2150000.mmc [2150000.mmc] using ADMA <6>[ 5.250389] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.262065] IPv4 over IPsec tunneling driver <6>[ 5.268810] NET: Registered protocol family 10 <6>[ 5.276377] Segment Routing with IPv6 <6>[ 5.282721] NET: Registered protocol family 17 <6>[ 5.288270] 8021q: 802.1Q VLAN Support v1.8 <6>[ 5.293201] 9pnet: Installing 9P2000 support <5>[ 5.297929] Key type dns_resolver registered <6>[ 5.303204] registered taskstats version 1 <5>[ 5.307657] Loading compiled-in X.509 certificates <6>[ 5.329753] fsl-edma 22c0000.dma-controller: Adding to iommu group 10 <6>[ 5.342610] pcieport 0001:00:00.0: Adding to iommu group 11 <6>[ 5.349262] pcieport 0001:00:00.0: PME: Signaling with IRQ 31 <6>[ 5.350635] mmc0: new HS400 MMC card at address 0001 <6>[ 5.356172] pcieport 0002:00:00.0: Adding to iommu group 12 <6>[ 5.360674] usb 3-1: new high-speed USB device number 2 using xhci-hcd <6>[ 5.367083] pcieport 0002:00:00.0: PME: Signaling with IRQ 33 <6>[ 5.381584] mmcblk0: mmc0:0001 S0J58X 29.6 GiB <6>[ 5.386907] mmcblk0boot0: mmc0:0001 S0J58X partition 1 31.5 MiB <6>[ 5.393872] mmcblk0boot1: mmc0:0001 S0J58X partition 2 31.5 MiB <6>[ 5.400617] mmcblk0rpmb: mmc0:0001 S0J58X partition 3 4.00 MiB, chardev (234:0) <6>[ 5.409783] input: buttons0 as /devices/platform/buttons0/input/input0 <6>[ 5.413747] mmcblk0: p1 p2 p3 <6>[ 5.483363] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:05] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.511413] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode <6>[ 5.566270] hub 3-1:1.0: USB hub found <6>[ 5.571122] hub 3-1:1.0: 7 ports detected <6>[ 5.589079] fsl_enetc 0000:00:00.1 eth1: PHY [0000:00:00.1:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) <6>[ 5.622507] fsl_enetc 0000:00:00.1 eth1: configuring for phy/rgmii-id link mode <6>[ 5.646312] fsl_enetc 0000:00:00.2 eth2: configuring for fixed/internal link mode <6>[ 5.654298] fsl_enetc 0000:00:00.2 eth2: Link is Up - 1Gbps/Full - flow control off <5>[ 5.673265] Sending DHCP requests . <6>[ 5.920957] usb 3-1.6: new full-speed USB device number 3 using xhci-hcd <3>[ 6.085094] hid-generic 0003:064F:2AF9.0001: device has no listeners, quitting <4>[ 8.216890] . <6>[ 8.590926] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx <6>[ 8.601387] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <4>[ 12.664888] ., OK <6>[ 12.683571] IP-Config: Got DHCP answer from 172.16.0.254, my address is 172.16.0.112 <6>[ 12.691941] IP-Config: Complete: <6>[ 12.695598] device=eth0, hwaddr=00:a0:a5:5c:6c:72, ipaddr=172.16.0.112, mask=255.255.255.0, gw=172.16.0.254 <6>[ 12.706216] host=172.16.0.112, domain=lava.lan, nis-domain=(none) <6>[ 12.713170] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 12.713207] nameserver0=8.8.8.8 <6>[ 12.754835] fsl_enetc 0000:00:00.2 eth2: Link is Down <6>[ 12.776508] ALSA device list: <6>[ 12.780001] No soundcards found. <6>[ 12.815074] Freeing unused kernel memory: 9792K <6>[ 12.820272] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 12.984046] udevd[136]: starting version 3.2.9 <5>[ 12.990465] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.997893] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 13.004844] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 13.017461] udevd[136]: specified user 'tss' unknown <27>[ 13.023068] udevd[136]: specified group 'tss' unknown <30>[ 13.031721] udevd[137]: starting eudev-3.2.9 <6>[ 13.913049] mali-dp f080000.display: Adding to iommu group 13 <27>[ 13.967379] udevd[145]: Error changing net interface name eth0 to enp0s0f0: Device or resource busy <6>[ 13.984484] mscc_felix 0000:00:00.5: Adding to iommu group 14 <6>[ 13.986786] fsl_enetc 0000:00:00.1 enp0s0f1: renamed from eth1 <6>[ 13.991247] mscc_felix 0000:00:00.5: enabling device (0400 -> 0402) <28>[ 14.051848] udevd[145]: could not rename interface '2' from 'eth0' to 'enp0s0f0': Device or resource busy <6>[ 14.085431] fsl_enetc 0000:00:00.2 enp0s0f2: renamed from eth2 <4>[ 14.101204] rtc-rv8803 0-0032: Voltage low, temperature compensation stopped. <4>[ 14.160809] rtc-rv8803 0-0032: Voltage low, data loss detected. <4>[ 14.225649] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 14.245551] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 14.258774] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 14.274691] sl28cpld-wdt 2000000.i2c:sl28cpld@4a:watchdog@4: initial timeout 6 sec <6>[ 14.282943] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 0 <6>[ 14.290300] rtc-rv8803 0-0032: registered as rtc0 <4>[ 14.299102] at24 1-0057: supply vcc not found, using dummy regulator <6>[ 14.306402] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 1 <4>[ 14.331851] rtc-rv8803 0-0032: Voltage low, data is invalid. <6>[ 14.337695] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 2 <3>[ 14.338446] rtc-rv8803 0-0032: hctosys: unable to read the hardware clock <6>[ 14.354229] at24 1-0057: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <4>[ 14.361983] at24 2-0050: supply vcc not found, using dummy regulator <6>[ 14.370853] mscc_felix 0000:00:00.5: Found PCS at internal MDIO address 3 <6>[ 14.375177] at24 2-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write <6>[ 14.533465] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:07] driver [Generic PHY] (irq=POLL) <6>[ 14.620778] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:08] driver [Generic PHY] (irq=POLL) <6>[ 14.661998] caam 8000000.crypto: device ID = 0x0a12070000000000 (Era 10) <6>[ 14.671251] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:09] driver [Generic PHY] (irq=POLL) <6>[ 14.691433] caam 8000000.crypto: job rings = 4, qi = 0 <6>[ 14.711559] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:0a] driver [Generic PHY] (irq=POLL) <6>[ 14.781378] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode <6>[ 14.814256] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control off <6>[ 14.826018] device enp0s0f2 entered promiscuous mode <6>[ 14.837007] DSA: tree 0 setup <6>[ 15.010671] caam_jr 8010000.jr: Adding to iommu group 15 <6>[ 15.019870] caam algorithms registered in /proc/crypto <6>[ 15.029018] caam 8000000.crypto: registering rng-caam <6>[ 15.055541] caam_jr 8020000.jr: Adding to iommu group 16 <6>[ 15.062957] caam_jr 8030000.jr: Adding to iommu group 17 <6>[ 15.069770] caam_jr 8040000.jr: Adding to iommu group 18 <5>[ 15.075821] random: crng init done <5>[ 15.079896] random: 2 urandom warning(s) missed due to ratelimiting done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-356911/environment . /lava-356911/environment / # /lava-356911/bin/lava-test-runner /lava-356911/0 /lava-356911/bin/lava-test-runner /lava-356911/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-356911/0/tests/0_dmesg + cat uuid + UUID=356911_1.<8>[ 15.867401] 5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.918985] <8>[ 15.970314] <8>[ 16.026803] + set<8>[ 16.041170] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-356911/environment / # . /lava-356911/environment/lava-356911/bin/lava-test-runner /lava-356911/1 / # /lava-356911/bin/lava-test-runner /lava-356911/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-356911/1/tests/1_bootrr + cat uuid + UUID=356911_1.<8>[ 16.557711] 5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-356911/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-356911/1/../bin/lava-test-case <8>[ 16.618031] /lava-356911/1/../bin/lava-test-case <8>[ 16.664055] /lava-356911/1/../bin/lava-test-case <8>[ 16.692801] /lava-356911/1/../bin/lava-test-case <8>[ 16.753797] /lava-356911/1/../bin/lava-test-case <8>[ 16.803064] /lava-356911/1/../bin/lava-test-case <8>[ 16.842993] /lava-356911/1/../bin/lava-test-case <8>[ 16.891169] /lava-356911/1/../bin/lava-test-case <8>[ 16.928631] /lava-356911/1/../bin/lava-test-case <8>[ 16.978117] /lava-356911/1/../bin/lava-test-case <8>[ 17.017789] /lava-356911/1/../bin/lava-test-case <8>[ 17.066913] /lava-356911/1/../bin/lava-test-case <8>[ 17.123282] /lava-356911/1/../bin/lava-test-case <8>[ 17.171411] /lava-356911/1/../bin/lava-test-case <8>[ 17.221481] /lava-356911/1/../bin/lava-test-case <8>[ 17.261482] /lava-356911/1/../bin/lava-test-case <8>[ 17.310200] /lava-356911/1/../bin/lava-test-case <8>[ 17.363036] /lava-356911/1/../bin/lava-test-case <8>[ 17.411298] /lava-356911/1/../bin/lava-test-case <8>[ 17.450978] /lava-356911/1/../bin/lava-test-case <8>[ 17.499320] /lava-356911/1/../bin/lava-test-case <8>[ 17.536615] /lava-356911/1/../bin/lava-test-case <8>[ 17.585663] /lava-356911/1/../bin/lava-test-case <8>[ 17.635044] /lava-356911/1/../bin/lava-test-case <8>[ 17.683005] /lava-356911/1/../bin/lava-test-case <8>[ 17.721015] /lava-356911/1/../bin/lava-test-case <8>[ 17.771442] /lava-356911/1/../bin/lava-test-case <8>[ 17.808651] /lava-356911/1/../bin/lava-test-case <8>[ 17.859671] /lava-356911/1/../bin/lava-test-case <8>[ 17.898223] /lava-356911/1/../bin/lava-test-case <8>[ 17.946658] /lava-356911/1/../bin/lava-test-case <8>[ 17.995243] /lava-356911/1/../bin/lava-test-case <8>[ 18.034812] /lava-356911/1/../bin/lava-test-case <8>[ 18.083247] /lava-356911/1/../bin/lava-test-case <8>[ 18.145798] /lava-356911/1/../bin/lava-test-case <8>[ 18.185058] /lava-356911/1/../bin/lava-test-case <8>[ 18.232872] /lava-356911/1/../bin/lava-test-case <8>[ 18.273318] /lava-356911/1/../bin/lava-test-case <8>[ 18.320933] /lava-356911/1/../bin/lava-test-case <8>[ 18.357779] /lava-356911/1/../bin/lava-test-case <8>[ 18.407397] /lava-356911/1/../bin/lava-test-case <8>[ 18.457355] /lava-356911/1/../bin/lava-test-case <8>[ 18.494534] /lava-356911/1/../bin/lava-test-case <8>[ 18.544451] /lava-356911/1/../bin/lava-test-case <8>[ 18.593412] /lava-356911/1/../bin/lava-test-case <8>[ 18.630565] /lava-356911/1/../bin/lava-test-case <8>[ 18.681112] /lava-356911/1/../bin/lava-test-case <8>[ 18.729104] /lava-356911/1/../bin/lava-test-case <8>[ 18.766602] /lava-356911/1/../bin/lava-test-case <8>[ 18.814634] /lava-356911/1/../bin/lava-test-case <8>[ 18.852550] /lava-356911/1/../bin/lava-test-case <8>[ 18.900594] /lava-356911/1/../bin/lava-test-case <8>[ 18.937790] /lava-356911/1/../bin/lava-test-case <8>[ 18.987350] /lava-356911/1/../bin/lava-test-case <8>[ 19.035078] /lava-356911/1/../bin/lava-test-case <8>[ 19.082760] /lava-356911/1/../bin/lava-test-case <8>[ 19.131862] /lava-356911/1/../bin/lava-test-case <8>[ 19.170658] /lava-356911/1/../bin/lava-test-case <8>[ 19.219025] /lava-356911/1/../bin/lava-test-case <8>[ 19.270528] /lava-356911/1/../bin/lava-test-case <8>[ 19.310167] /lava-356911/1/../bin/lava-test-case <8>[ 19.358717] /lava-356911/1/../bin/lava-test-case <8>[ 19.397146] /lava-356911/1/../bin/lava-test-case <8>[ 19.445485] /lava-356911/1/../bin/lava-test-case <8>[ 20.488311] /lava-356911/1/../bin/lava-test-case <8>[ 21.532080] /lava-356911/1/../bin/lava-test-case <8>[ 22.575385] /lava-356911/1/../bin/lava-test-case <8>[ 23.622138] /lava-356911/1/../bin/lava-test-case <8>[ 23.661416] /lava-356911/1/../bin/lava-test-case <8>[ 23.710645] /lava-356911/1/../bin/lava-test-case <8>[ 23.748423] /lava-356911/1/../bin/lava-test-case <8>[ 23.800194] /lava-356911/1/../bin/lava-test-case <8>[ 23.840550] /lava-356911/1/../bin/lava-test-case <8>[ 23.891580] /lava-356911/1/../bin/lava-test-case <8>[ 23.930890] /lava-356911/1/../bin/lava-test-case <8>[ 23.983108] /lava-356911/1/../bin/lava-test-case <8>[ 24.030719] /lava-356911/1/../bin/lava-test-case <8>[ 24.068786] /lava-356911/1/../bin/lava-test-case <8>[ 24.117289] /lava-356911/1/../bin/lava-test-case <8>[ 24.165573] /lava-356911/1/../bin/lava-test-case <8>[ 24.215288] /lava-356911/1/../bin/lava-test-case <8>[ 24.266644] /lava-356911/1/../bin/lava-test-case <8>[ 24.305134] /lava-356911/1/../bin/lava-test-case <8>[ 24.355698] /lava-356911/1/../bin/lava-test-case <8>[ 24.396097] /lava-356911/1/../bin/lava-test-case <8>[ 24.446327] /lava-356911/1/../bin/lava-test-case <8>[ 24.486440] /lava-356911/1/../bin/lava-test-case <8>[ 24.533885] /lava-356911/1/../bin/lava-test-case <8>[ 24.582221] /lava-356911/1/../bin/lava-test-case <8>[ 24.619448] /lava-356911/1/../bin/lava-test-case <8>[ 24.669351] /lava-356911/1/../bin/lava-test-case <8>[ 25.712087] /lava-356911/1/../bin/lava-test-case <8>[ 26.758766] + set +x<8>[ 26.781673] / # �