[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (9 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11005308/tftp-deploy-wx4mxuaw/kernel/zImage tftp 0x10000000 11005308/tftp-deploy-wx4mxuaw/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11005308/tftp-deploy-wx4mxuaw/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 5.6 MiB/s done Bytes transferred = 12403200 (bd4200 hex) => tftp 0x14000000 11005308/tftp-deploy-wx4mxuaw/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11005308/tftp-deploy-wx4mxuaw/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11005308/tftp-deploy-wx4mxuaw/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################### 11.4 MiB/s done Bytes transferred = 19398134 (127fdf6 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11005308/tftp-deploy-wx4mxuaw/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11005308/tftp-deploy-wx4mxuaw/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11005308/tftp-deploy-wx4mxuaw/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.1 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbd4200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19398070 Bytes = 18.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.184-cip36 (KernelCI@build-j123671-arm-gcc-10-multi-v7-defconfig-kselftest-pkv9b) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jul 4 06:05:44 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917572K/1048576K available (17408K kernel code, 2658K rwdata, 8108K rodata, 2048K init, 6693K bss, 65468K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 55432 entries in 163 pages <6>[ 0.000000] ftrace: allocated 163 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022982] Console: colour dummy device 80x30 <4>[ 0.024885] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032896] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037242] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041653] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046288] ... CLASSHASH_SIZE: 4096 <4>[ 0.050874] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055597] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060270] ... CHAINHASH_SIZE: 32768 <4>[ 0.064968] memory used by lock dependency info: 4061 kB <4>[ 0.070647] memory used for stack traces: 2112 kB <4>[ 0.075693] per task-struct memory footprint: 1536 bytes <6>[ 0.081380] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091797] pid_max: default: 32768 minimum: 301 <6>[ 0.096994] LSM: Security Framework initializing <6>[ 0.101587] LSM support for eBPF active <6>[ 0.105746] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.113187] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123722] CPU: Testing write buffer coherency: ok <6>[ 0.126351] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.132504] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141079] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147500] rcu: Hierarchical SRCU implementation. <6>[ 0.158856] EFI services will not be available. <6>[ 0.161959] smp: Bringing up secondary CPUs ... <6>[ 0.168537] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.168552] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180432] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180446] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.191962] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.191976] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.201029] smp: Brought up 1 node, 4 CPUs <6>[ 0.204722] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211261] CPU: All CPU(s) started in SVC mode. <6>[ 0.218522] devtmpfs: initialized <6>[ 0.268319] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.275893] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.283610] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.295491] pinctrl core: initialized pinctrl subsystem <6>[ 0.304411] DMI not present or invalid. <6>[ 0.307851] NET: Registered protocol family 16 <6>[ 0.320090] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.332987] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.333493] cpuidle: using governor menu <6>[ 0.341552] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.978920] vdd1p1: supplied by regulator-dummy <6>[ 1.007845] vdd3p0: supplied by regulator-dummy <6>[ 1.036427] vdd2p5: supplied by regulator-dummy <6>[ 1.064940] vddarm: supplied by regulator-dummy <6>[ 1.094354] vddpu: supplied by regulator-dummy <6>[ 1.122082] vddsoc: supplied by regulator-dummy <6>[ 2.258246] No ATAGs? <6>[ 2.259124] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.266285] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.289198] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.318794] Serial: AMBA PL011 UART driver <6>[ 2.376542] Kprobes globally optimized <6>[ 2.480780] iommu: Default domain type: Translated <6>[ 2.485264] vgaarb: loaded <5>[ 2.490341] SCSI subsystem initialized <6>[ 2.493817] usbcore: registered new interface driver usbfs <6>[ 2.497565] usbcore: registered new interface driver hub <6>[ 2.503018] usbcore: registered new device driver usb <6>[ 2.514849] i2c i2c-0: IMX I2C adapter registered <6>[ 2.523091] i2c i2c-1: IMX I2C adapter registered <6>[ 2.529232] i2c i2c-2: IMX I2C adapter registered <6>[ 2.535460] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.537858] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.547361] PTP clock support registered <6>[ 2.566458] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.134926] NET: Registered protocol family 2 <6>[ 4.137552] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.147425] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.153436] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.161581] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.170249] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.176343] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.183620] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.190221] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.197972] NET: Registered protocol family 1 <6>[ 4.204374] RPC: Registered named UNIX socket transport module. <6>[ 4.208160] RPC: Registered udp transport module. <6>[ 4.212985] RPC: Registered tcp transport module. <6>[ 4.217990] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.224663] NET: Registered protocol family 44 <6>[ 4.229416] PCI: CLS 0 bytes, default 64 <6>[ 4.236087] Trying to unpack rootfs image as initramfs... <6>[ 6.649715] Freeing initrd memory: 18944K <4>[ 6.652005] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.659775] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.675144] Initialise system trusted keyrings <6>[ 6.678118] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.727663] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.734211] NFS: Registering the id_resolver key type <5>[ 6.736930] Key type id_resolver registered <5>[ 6.741144] Key type id_legacy registered <6>[ 6.745903] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.752481] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.760221] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.766548] Key type asymmetric registered <5>[ 6.769054] Asymmetric key parser 'x509' registered <6>[ 6.774428] bounce: pool size: 64 pages <6>[ 6.778391] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.785915] io scheduler mq-deadline registered <6>[ 6.790710] io scheduler kyber registered <4>[ 6.795725] test_firmware: interface ready <6>[ 6.956993] mxs-dma 110000.dma-apbh: initialized <4>[ 7.015973] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.023217] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 7.238181] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.260134] SuperH (H)SCI(F) driver initialized <6>[ 7.264771] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.275595] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.282111] printk: console [ttymxc1] enabled <6>[ 7.282111] printk: console [ttymxc1] enabled <6>[ 7.290930] printk: bootconsole [ec_imx21] disabled <6>[ 7.290930] printk: bootconsole [ec_imx21] disabled <6>[ 7.307341] msm_serial: driver initialized <6>[ 7.312660] STMicroelectronics ASC driver initialized <6>[ 7.323898] STM32 USART driver initialized <6>[ 7.347787] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.367913] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.376592] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.384448] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.433533] brd: module loaded <6>[ 7.487141] loop: module loaded <6>[ 7.493389] lkdtm: No crash points registered, enable through debugfs <6>[ 7.514199] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.522511] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.530871] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.539395] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.547656] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.555972] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.563973] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.575561] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.582930] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.592071] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.606225] scsi host0: ahci-imx <6>[ 7.611882] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.670897] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.684243] pps pps0: new PPS source ptp0 <6>[ 7.744068] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.754565] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.759876] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.766301] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.772038] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.797897] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.805728] usbcore: registered new interface driver pegasus <6>[ 7.811950] usbcore: registered new interface driver asix <6>[ 7.817823] usbcore: registered new interface driver ax88179_178a <6>[ 7.824332] usbcore: registered new interface driver cdc_ether <6>[ 7.830690] usbcore: registered new interface driver smsc75xx <6>[ 7.836955] usbcore: registered new interface driver smsc95xx <6>[ 7.843119] usbcore: registered new interface driver net1080 <6>[ 7.849257] usbcore: registered new interface driver cdc_subset <6>[ 7.855589] usbcore: registered new interface driver zaurus <6>[ 7.861723] usbcore: registered new interface driver cdc_ncm <6>[ 7.879308] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.886196] ehci-pci: EHCI PCI platform driver <6>[ 7.891125] ehci-platform: EHCI generic platform driver <6>[ 7.897608] ehci-orion: EHCI orion driver <6>[ 7.902724] SPEAr-ehci: EHCI SPEAr driver <6>[ 7.907846] ehci-st: EHCI STMicroelectronics driver <6>[ 7.913773] ehci-exynos: EHCI Exynos driver <6>[ 7.919050] ehci-atmel: EHCI Atmel driver <6>[ 7.924109] tegra-ehci: Tegra EHCI driver <6>[ 7.929281] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 7.935816] ohci-pci: OHCI PCI platform driver <6>[ 7.940736] ohci-platform: OHCI generic platform driver <6>[ 7.947177] SPEAr-ohci: OHCI SPEAr driver <6>[ 7.952251] ohci-st: OHCI STMicroelectronics driver <6>[ 7.958232] ohci-atmel: OHCI Atmel driver <6>[ 7.966493] usbcore: registered new interface driver usb-storage <6>[ 7.968882] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 7.978880] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 7.985446] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.002255] i2c /dev entries driver <6>[ 8.080279] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.086807] sdhci: Copyright(c) Pierre Ossman <6>[ 8.100265] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.113256] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.122852] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.128384] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.135215] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.135858] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.150357] usbcore: registered new interface driver usbhid <6>[ 8.156225] usbhid: USB HID core driver <6>[ 8.177099] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.177108] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.182672] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.184977] IPv4 over IPsec tunneling driver <6>[ 8.206505] NET: Registered protocol family 10 <6>[ 8.216715] Segment Routing with IPv6 <6>[ 8.226280] NET: Registered protocol family 17 <6>[ 8.230504] mmc2: new high speed SDHC card at address 0001 <5>[ 8.232985] Key type dns_resolver registered <6>[ 8.240517] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 8.260414] ThumbEE CPU extension supported. <5>[ 8.265045] Registering SWP/SWPB emulation handler <5>[ 8.271242] Loading compiled-in X.509 certificates <4>[ 8.272469] GPT:disk_guids don't match. <4>[ 8.280748] GPT:partition_entry_array_crc32 values don't match: 0xaf767936 != 0x8af2d11f <4>[ 8.289200] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 8.296927] GPT:29296874 != 30560255 <4>[ 8.300789] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.307113] GPT:29296874 != 30560255 <4>[ 8.310975] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.316517] mmcblk2: p1 p2 p3 <4>[ 8.427690] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.436181] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.448619] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.481797] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.494673] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.500228] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.537041] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.556018] hub 1-0:1.0: USB hub found <6>[ 8.560643] hub 1-0:1.0: 1 port detected <6>[ 8.575391] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.605944] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.614454] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.626883] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.654257] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.662824] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.675153] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.692375] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.721541] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.730029] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.742502] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.763681] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 8.926925] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.135021] hub 1-1:1.0: USB hub found <6>[ 9.140088] hub 1-1:1.0: 3 ports detected <4>[ 9.168694] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.177167] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.189678] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.918387] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 11.927967] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 11.956524] Sending DHCP requests ., OK <6>[ 12.001121] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 12.009598] IP-Config: Complete: <6>[ 12.013165] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 12.024123] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 12.032385] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 12.032426] nameserver0=192.168.201.1 <6>[ 12.098942] Freeing unused kernel memory: 2048K <6>[ 12.107187] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 12.514418] udevd[144]: starting version 3.2.9 <5>[ 12.524070] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.531818] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.538806] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 12.558109] udevd[144]: specified user 'tss' unknown <27>[ 12.563671] udevd[144]: specified group 'tss' unknown <30>[ 12.577815] udevd[145]: starting eudev-3.2.9 <6>[ 13.746311] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 13.823245] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 13.847187] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 13.855688] panel-simple panel-lcd: Specify missing connector_type <4>[ 13.929393] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 13.976724] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 13.985258] panel-simple panel-lcd: Specify missing connector_type <4>[ 13.999789] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.075588] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.085150] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.094538] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.103492] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.163853] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.172530] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.242669] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.301203] CAN device driver interface <6>[ 14.341678] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.394579] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.423916] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.430964] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 14.457645] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 14.476576] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 14.482975] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 14.518004] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <6>[ 14.597059] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.605828] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.614693] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.623433] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.700484] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.787028] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.799911] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.846252] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.849714] caam 2100000.crypto: Entropy delay = 3200 <6>[ 14.855050] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.868917] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.877686] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.920885] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 14.981650] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 14.987149] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 14.994058] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 15.035925] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.046541] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 15.055857] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 15.091608] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.103960] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 15.117161] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.152907] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.199711] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.208843] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.217703] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.226685] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.257708] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 15.269370] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 15.270578] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.292926] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.310624] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.338833] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.347929] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.356847] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.365539] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.434892] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.443487] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.456222] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.476021] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.484888] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.493707] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.502432] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.940901] caam algorithms registered in /proc/crypto <6>[ 15.960916] caam 2100000.crypto: registering rng-caam <5>[ 16.090235] random: crng init done <5>[ 16.094038] random: 1 urandom warning(s) missed due to ratelimiting <4>[ 16.116695] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.125359] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.138545] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.158523] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.167328] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.176032] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.184732] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.212313] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.220871] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.233429] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.252585] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.261302] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.270469] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.279363] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11005308/environment . /lava-11005308/environment / # /lava-11005308/bin/lava-test-runner /lava-11005308/0 /lava-11005308/bin/lava-test-runner /lava-11005308/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-11005308/0/tests/0_dmesg + cat uuid + UUID=11005308_1.5.2.4.1<8>[ 17.460257] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.586193] <8>[ 17.700572] <8>[ 17.817328] + set +x <8>[ 17.829442] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11005308/environment / # . /lava-11005308/environment/lava-11005308/bin/lava-test-runner /lava-11005308/1 / # /lava-11005308/bin/lava-test-runner /lava-11005308/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-11005308/1/tests/1_bootrr + cat uuid + UUID=11005308_1.5.2.4.5<8>[ 18.478621] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11005308/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lcd backlight-lvds panel-lcd panel-lvds0 120000.hdmi /lava-11005308/1/../bin/lava-test-case <8>[ 19.679542] /lava-11005308/1/../bin/lava-test-case <8>[ 19.799453] /lava-11005308/1/../bin/lava-test-case <8>[ 19.866145] + set +x <8>[ 19.909323] / #