[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.35 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11263725/tftp-deploy-fcy3i6gf/kernel/zImage tftp 0x10000000 11263725/tftp-deploy-fcy3i6gf/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11263725/tftp-deploy-fcy3i6gf/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 14 MiB/s done Bytes transferred = 12427776 (bda200 hex) => tftp 0x14000000 11263725/tftp-deploy-fcy3i6gf/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11263725/tftp-deploy-fcy3i6gf/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11263725/tftp-deploy-fcy3i6gf/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################ 5.8 MiB/s done Bytes transferred = 15493177 (ec6839 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11263725/tftp-deploy-fcy3i6gf/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11263725/tftp-deploy-fcy3i6gf/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.35 Filename '11263725/tftp-deploy-fcy3i6gf/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42645 (a695 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11263725/extract-nfsrootfs-ger1rhsx,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11263725/extract-nfsrootfs-ger1rhsx,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbda200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15493113 Bytes = 14.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d694 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.190-cip37 (KernelCI@build-j9707-arm-gcc-10-multi-v7-defconfig-kselftest-mfdsh) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Aug 11 13:35:30 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11263725/extract-nfsrootfs-ger1rhsx,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 921332K/1048576K available (17408K kernel code, 2710K rwdata, 8116K rodata, 2048K init, 6692K bss, 61708K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 55492 entries in 163 pages <6>[ 0.000000] ftrace: allocated 163 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022887] Console: colour dummy device 80x30 <4>[ 0.024794] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032801] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037144] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041556] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046192] ... CLASSHASH_SIZE: 4096 <4>[ 0.050779] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055500] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060175] ... CHAINHASH_SIZE: 32768 <4>[ 0.064872] memory used by lock dependency info: 4061 kB <4>[ 0.070551] memory used for stack traces: 2112 kB <4>[ 0.075596] per task-struct memory footprint: 1536 bytes <6>[ 0.081287] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091699] CPU: Testing write buffer coherency: ok <6>[ 0.096838] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102112] pid_max: default: 32768 minimum: 301 <6>[ 0.107313] LSM: Security Framework initializing <6>[ 0.111932] LSM support for eBPF active <6>[ 0.116089] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123533] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.134999] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141656] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.148047] rcu: Hierarchical SRCU implementation. <6>[ 0.159452] EFI services will not be available. <6>[ 0.162552] smp: Bringing up secondary CPUs ... <6>[ 0.169146] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.169161] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.181019] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.181034] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.192576] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.192590] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.201626] smp: Brought up 1 node, 4 CPUs <6>[ 0.205336] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211875] CPU: All CPU(s) started in SVC mode. <6>[ 0.219137] devtmpfs: initialized <6>[ 0.268405] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.275980] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.283686] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.295597] pinctrl core: initialized pinctrl subsystem <6>[ 0.304547] DMI not present or invalid. <6>[ 0.308029] NET: Registered protocol family 16 <6>[ 0.320342] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.333175] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.333673] cpuidle: using governor menu <6>[ 0.341743] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.996338] vdd1p1: supplied by regulator-dummy <6>[ 1.025889] vdd3p0: supplied by regulator-dummy <6>[ 1.055021] vdd2p5: supplied by regulator-dummy <6>[ 1.084360] vddarm: supplied by regulator-dummy <6>[ 1.114398] vddpu: supplied by regulator-dummy <6>[ 1.143001] vddsoc: supplied by regulator-dummy <6>[ 2.307863] No ATAGs? <6>[ 2.308694] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.315901] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.338992] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.368864] Serial: AMBA PL011 UART driver <6>[ 2.426523] Kprobes globally optimized <6>[ 2.531149] iommu: Default domain type: Translated <6>[ 2.535727] vgaarb: loaded <5>[ 2.540694] SCSI subsystem initialized <6>[ 2.544333] usbcore: registered new interface driver usbfs <6>[ 2.547851] usbcore: registered new interface driver hub <6>[ 2.553405] usbcore: registered new device driver usb <6>[ 2.565387] i2c i2c-0: IMX I2C adapter registered <6>[ 2.573575] i2c i2c-1: IMX I2C adapter registered <6>[ 2.579716] i2c i2c-2: IMX I2C adapter registered <6>[ 2.585981] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.588378] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.597948] PTP clock support registered <6>[ 2.616701] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.188435] NET: Registered protocol family 2 <6>[ 4.190960] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.200985] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.207098] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.215048] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.223814] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.230325] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.236977] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.243719] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.251551] NET: Registered protocol family 1 <6>[ 4.258200] RPC: Registered named UNIX socket transport module. <6>[ 4.261598] RPC: Registered udp transport module. <6>[ 4.266545] RPC: Registered tcp transport module. <6>[ 4.271581] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.278268] NET: Registered protocol family 44 <6>[ 4.282933] PCI: CLS 0 bytes, default 64 <6>[ 4.289686] Trying to unpack rootfs image as initramfs... <6>[ 6.097742] Freeing initrd memory: 15132K <4>[ 6.100282] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.107946] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.123085] Initialise system trusted keyrings <6>[ 6.125968] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.174937] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.181475] NFS: Registering the id_resolver key type <5>[ 6.184092] Key type id_resolver registered <5>[ 6.188496] Key type id_legacy registered <6>[ 6.193161] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.199744] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.207486] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.213756] Key type asymmetric registered <5>[ 6.216325] Asymmetric key parser 'x509' registered <6>[ 6.221770] bounce: pool size: 64 pages <6>[ 6.225577] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.233235] io scheduler mq-deadline registered <6>[ 6.237962] io scheduler kyber registered <4>[ 6.242983] test_firmware: interface ready <6>[ 6.405466] mxs-dma 110000.dma-apbh: initialized <4>[ 6.465446] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.472676] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 6.685798] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.708050] SuperH (H)SCI(F) driver initialized <6>[ 6.712702] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 6.723507] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 6.730048] printk: console [ttymxc1] enabled <6>[ 6.730048] printk: console [ttymxc1] enabled <6>[ 6.738863] printk: bootconsole [ec_imx21] disabled <6>[ 6.738863] printk: bootconsole [ec_imx21] disabled <6>[ 6.754840] msm_serial: driver initialized <6>[ 6.760323] STMicroelectronics ASC driver initialized <6>[ 6.771601] STM32 USART driver initialized <6>[ 6.797022] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 6.817200] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.825838] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.833766] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.883433] brd: module loaded <6>[ 6.929049] loop: module loaded <6>[ 6.935391] lkdtm: No crash points registered, enable through debugfs <6>[ 6.956195] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 6.964509] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 6.972863] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 6.981386] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 6.989671] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 6.998080] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.006011] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.017532] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.024814] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.033987] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.048129] scsi host0: ahci-imx <6>[ 7.053723] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.113202] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.126720] pps pps0: new PPS source ptp0 <6>[ 7.170268] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.180824] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.186081] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.192566] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.198298] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.224326] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.232209] usbcore: registered new interface driver pegasus <6>[ 7.238391] usbcore: registered new interface driver asix <6>[ 7.244210] usbcore: registered new interface driver ax88179_178a <6>[ 7.250784] usbcore: registered new interface driver cdc_ether <6>[ 7.257140] usbcore: registered new interface driver smsc75xx <6>[ 7.263357] usbcore: registered new interface driver smsc95xx <6>[ 7.269567] usbcore: registered new interface driver net1080 <6>[ 7.275641] usbcore: registered new interface driver cdc_subset <6>[ 7.282022] usbcore: registered new interface driver zaurus <6>[ 7.288204] usbcore: registered new interface driver cdc_ncm <6>[ 7.305777] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.312771] ehci-pci: EHCI PCI platform driver <6>[ 7.317717] ehci-platform: EHCI generic platform driver <6>[ 7.324173] ehci-orion: EHCI orion driver <6>[ 7.329339] SPEAr-ehci: EHCI SPEAr driver <6>[ 7.334415] ehci-st: EHCI STMicroelectronics driver <6>[ 7.340408] ehci-exynos: EHCI Exynos driver <6>[ 7.345635] ehci-atmel: EHCI Atmel driver <6>[ 7.350737] tegra-ehci: Tegra EHCI driver <6>[ 7.355842] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 7.362419] ohci-pci: OHCI PCI platform driver <6>[ 7.367357] ohci-platform: OHCI generic platform driver <6>[ 7.373750] SPEAr-ohci: OHCI SPEAr driver <6>[ 7.378880] ohci-st: OHCI STMicroelectronics driver <6>[ 7.384821] ohci-atmel: OHCI Atmel driver <6>[ 7.393078] usbcore: registered new interface driver usb-storage <6>[ 7.399323] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 7.405373] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 7.412007] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 7.429471] i2c /dev entries driver <6>[ 7.508404] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.514881] sdhci: Copyright(c) Pierre Ossman <6>[ 7.528473] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.541569] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.551055] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 7.551061] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 7.561862] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 7.568540] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 7.578450] usbcore: registered new interface driver usbhid <6>[ 7.584317] usbhid: USB HID core driver <6>[ 7.605229] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 7.610846] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.620569] IPv4 over IPsec tunneling driver <6>[ 7.625452] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 7.629654] NET: Registered protocol family 10 <6>[ 7.642863] Segment Routing with IPv6 <6>[ 7.652581] NET: Registered protocol family 17 <5>[ 7.659384] Key type dns_resolver registered <6>[ 7.678632] ThumbEE CPU extension supported. <5>[ 7.683260] Registering SWP/SWPB emulation handler <5>[ 7.689624] Loading compiled-in X.509 certificates <4>[ 7.848216] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.856798] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.864464] mmc2: new high speed SDHC card at address 0001 <4>[ 7.869492] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.873548] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 7.910618] imx_usb 2184200.usb: No over current polarity defined <4>[ 7.924857] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 7.926307] ci_hdrc ci_hdrc.1: EHCI Host Controller <4>[ 7.932732] GPT:29296874 != 30560255 <6>[ 7.938175] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 7.941768] GPT:Alternate GPT header not at the end of the disk. <4>[ 7.955401] GPT:29296874 != 30560255 <4>[ 7.959319] GPT: Use GNU Parted to correct GPT errors. <6>[ 7.964794] mmcblk2: p1 p2 p3 <6>[ 7.997260] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.016488] hub 1-0:1.0: USB hub found <6>[ 8.021105] hub 1-0:1.0: 1 port detected <6>[ 8.035931] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.065765] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.074439] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.087289] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.115366] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.123925] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.136454] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.154365] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.183258] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.191725] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.204384] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.225219] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 8.406996] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 8.615225] hub 1-1:1.0: USB hub found <6>[ 8.621295] hub 1-1:1.0: 3 ports detected <4>[ 8.651453] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.660140] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.674311] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.358583] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 11.387198] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 11.416934] Sending DHCP requests ., OK <6>[ 11.461365] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.35 <6>[ 11.469762] IP-Config: Complete: <6>[ 11.473285] device=eth0, hwaddr=00:19:b8:08:f1:09, ipaddr=192.168.201.35, mask=255.255.255.0, gw=192.168.201.1 <6>[ 11.484053] host=imx6q-sabrelite-lava-cbg-5, domain=lava-rack, nis-domain=(none) <6>[ 11.492242] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 11.492262] nameserver0=192.168.201.1 <6>[ 11.552707] Freeing unused kernel memory: 2048K <6>[ 11.558864] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 15.080668] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 15.122101] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 15.136106] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 15.143682] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.169113] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.175463] CAN device driver interface <4>[ 15.216393] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.231019] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.247457] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.282548] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.304342] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.330759] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.337657] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 15.347518] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 15.355128] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 15.361641] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 15.371561] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <6>[ 15.384726] caam 2100000.crypto: Entropy delay = 3200 <4>[ 15.438318] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.446904] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.451049] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 15.460328] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.511815] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.517320] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 15.524225] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 15.562846] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.566296] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.571506] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.579601] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 15.591879] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.594246] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 15.628688] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 15.648326] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.657965] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.667565] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 15.668527] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.682419] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.689919] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.691659] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.717578] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 15.721544] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.731387] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.774706] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 15.794863] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.832013] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.840757] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.861932] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.870867] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.879645] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.888358] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.903757] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.933372] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.941926] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.395282] caam algorithms registered in /proc/crypto <6>[ 16.413351] caam 2100000.crypto: registering rng-caam <6>[ 16.437923] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.446616] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.455407] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.464281] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.480612] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 16.516111] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.524715] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.544293] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.553164] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.561926] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.570683] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 s<5>[ 16.602652] random: crng init done ecs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:09 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.35 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-5 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 18.399769] systemd[1]: System time before build time, advancing clock. <30>[ 18.721671] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 18.748993] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 18.813690] systemd[1]: Set hostname to . <30>[ 20.328176] systemd[1]: Queued start job for default target Graphical Interface. <30>[ 20.343273] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 20.401599] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 20.451655] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 20.501057] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 20.550953] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 20.600106] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 20.648414] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 20.662445] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 20.709052] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 20.747244] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 20.787712] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 20.827738] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 20.881853] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 20.981989] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 20.995207] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 21.043240] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 21.103537] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 21.159017] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 21.202243] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 21.250811] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 21.260400] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 21.282263] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 21.330176] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 21.398758] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 21.463590] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 21.510215] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 21.560012] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 21.623185] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <6>[ 21.628395] fuse: init (API version 7.32) <30>[ 21.657951] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 21.723358] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 21.778511] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 21.835722] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 21.903461] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 21.949036] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 21.994720] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 22.088477] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 22.098482] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 22.152095] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 22.162004] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 22.213473] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 22.223342] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 22.272129] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 22.318325] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Remount Root and Kernel File Systems. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 22.627291] systemd-journald[272]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Started Network Service. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. Starting Network Name Resolution... [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.190-cip37 #1 SMP Fri Aug 11 13:35:30 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11263725/extract-nfsrootfs-ger1rhsx' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11263725/extract-nfsrootfs-ger1rhsx' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-11263725/environment . /lava-11263725/environment / # /lava-11263725/bin/lava-test-runner /lava-11263725/0 /lava-11263725/bin/lava-test-runner /lava-11263725/0 + export TESTRUN_ID=0_dmesg + cd /lava-11263725/0/tests/0_dmesg + cat uuid + UUID=11263725_1.6.2.4.1<8>[ 41.374919] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 41.591532] <8>[ 41.767879] <8>[ 41.950462] + set +x <8>[ 41.961798] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-11263725/environment / # . /lava-11263725/environment/lava-11263725/bin/lava-test-runner /lava-11263725/1 / # /lava-11263725/bin/lava-test-runner /lava-11263725/1 + export TESTRUN_ID=1_bootrr + cd /lava-11263725/1/tests/1_bootrr + cat uuid + UUID=11263725_1.6.2.4.5<8>[ 42.748574] + set +x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-11263725/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd 120000.hdmi /lava-11263725/1/../bin/lava-test-case <8>[ 44.100728] /lava-11263725/1/../bin/lava-test-case <8>[ 44.280723] /lava-11263725/1/../bin/lava-test-case <8>[ 44.368769] + set +x <8>[ 44.429583] / #