Connected to r8a7743-iwg20d-q7-02 console [channel connected] (~$quit to exit) iW-RainboW-G20M SPI_LOADER(DDR3) V0.20 2015.07.16 BSP Version : iW-PREWZ-SC-01-REL2.0-Linux3.10.31-PATCH004 DEVICE SST25VF016B U-Boot 2013.01.01-gc6f24b0 (Mar 15 2019 - 14:43:06) CPU: Renesas Electronics R8A7743 rev 3.0 CPU: Temperature 50 C Board: RZ/G1M iW-RainboW-G20M-Q7 DRAM: 1 GiB MMC: sh-sdhi: 0, sh-sdhi: 1, sh_mmcif: 2 SF: Detected SST25VF016B with page size 4 KiB, total 2 MiB In: serial Out: serial Err: serial Board Info: SOM Version : iW-PREWZ-AP-01-R3.3 Net: ether_avb Hit any key to stop autoboot: 3  0 iWave-G20M > setenv autoload no setenv autoload no iWave-G20M > setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff iWave-G20M > setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff iWave-G20M > dhcp dhcp Could not get PHY for ether_avb:0 Could not get PHY for ether_avb:1 Could not get PHY for ether_avb:2 PHY detected at addr 3 ether_avb Waiting for PHY auto negotiation to complete.. done ether_avb: 1000Base /Full BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.1.16 iWave-G20M > setenv serverip 192.168.1.1 setenv serverip 192.168.1.1 iWave-G20M > tftp 0x40007fc0 995808/tftp-deploy-bucb55ub/kernel/uImage tftp 0x40007fc0 995808/tftp-deploy-bucb55ub/kernel/uImage Could not get PHY for ether_avb:0 Could not get PHY for ether_avb:1 Could not get PHY for ether_avb:2 ether_avb:3 is connected to ether_avb. Reconnecting to ether_avb PHY detected at addr 3 ether_avb Waiting for PHY auto negotiation to complete.. done ether_avb: 1000Base /Full Using ether_avb device TFTP from server 192.168.1.1; our IP address is 192.168.1.16 Filename '995808/tftp-deploy-bucb55ub/kernel/uImage'. Load address: 0x40007fc0 Loading: *T ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############## 886.7 KiB/s done Bytes transferred = 4971360 (4bdb60 hex) iWave-G20M > tftp 0x41f00000 995808/tftp-deploy-bucb55ub/ramdisk/ramdisk.cpio.gz.uboot tftp 0x41f00000 995808/tftp-deploy-bucb55ub/ramdisk/ramdisk.cpio.gz.uboot Could not get PHY for ether_avb:0 Could not get PHY for ether_avb:1 Could not get PHY for ether_avb:2 ether_avb:3 is connected to ether_avb. Reconnecting to ether_avb PHY detected at addr 3 ether_avb Waiting for PHY auto negotiation to complete.. done ether_avb: 1000Base /Full Using ether_avb device TFTP from server 192.168.1.1; our IP address is 192.168.1.16 Filename '995808/tftp-deploy-bucb55ub/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x41f00000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##################### 10.1 MiB/s done Bytes transferred = 7941467 (792d5b hex) iWave-G20M > setenv initrd_size ${filesize} setenv initrd_size ${filesize} iWave-G20M > tftp 0x48000000 995808/tftp-deploy-bucb55ub/dtb/r8a7743-iwg20d-q7.dtb tftp 0x48000000 995808/tftp-deploy-bucb55ub/dtb/r8a7743-iwg20d-q7.dtb Could not get PHY for ether_avb:0 Could not get PHY for ether_avb:1 Could not get PHY for ether_avb:2 ether_avb:3 is connected to ether_avb. Reconnecting to ether_avb PHY detected at addr 3 ether_avb Waiting for PHY auto negotiation to complete.. done ether_avb: 1000Base /Full Using ether_avb device TFTP from server 192.168.1.1; our IP address is 192.168.1.16 Filename '995808/tftp-deploy-bucb55ub/dtb/r8a7743-iwg20d-q7.dtb'. Load address: 0x48000000 Loading: *### 9.5 MiB/s done Bytes transferred = 39838 (9b9e hex) iWave-G20M > setenv bootargs 'console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' iWave-G20M > bootm 0x40007fc0 0x41f00000 0x48000000 bootm 0x40007fc0 0x41f00000 0x48000000 ## Booting kernel from Legacy Image at 40007fc0 ... Image Name: Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4971296 Bytes = 4.7 MiB Load Address: 40007fc0 Entry Point: 40007fc0 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 41f00000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 7941403 Bytes = 7.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 48000000 Booting using the fdt blob at 0x48000000 XIP Kernel Image ... OK OK Using Device Tree in place at 48000000, end 4800cb9d Unable to update property /iwg20m_q7_common:vin2-ov5640, err=FDT_ERR_NOTFOUND Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.190-cip37 (KernelCI@build-j9771-arm-gcc-10-shmobile-defconfig-kk52q) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Aug 11 13:39:58 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc0f2] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: iWave Systems RainboW-G20D-Qseven board based on RZ/G1M [ 0.000000] OF: fdt: Ignoring memory block 0x200000000 - 0x220000000 [ 0.000000] earlycon: scif0 at MMIO 0xe6e60000 (options '115200n8') [ 0.000000] printk: bootconsole [scif0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 256 MiB at 0x50000000 [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] percpu: Embedded 17 pages/cpu s47948 r0 d21684 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttySC0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 170764K/524288K available (7168K kernel code, 1086K rwdata, 2228K rodata, 1024K init, 288K bss, 25844K reserved, 327680K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 10.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x24e6a1710, max_idle_ns: 440795202120 ns <6>[ 0.000005] sched_clock: 56 bits at 10MHz, resolution 100ns, wraps every 4398046511100ns <6>[ 0.008055] Switching to timer-based delay loop, resolution 100ns <6>[ 0.014518] Console: colour dummy device 80x30 <6>[ 0.019072] Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj=100000) <6>[ 0.029316] CPU: Testing write buffer coherency: ok <3>[ 0.034289] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.043686] CPU0: Spectre BHB: enabling loop workaround for all CPUs <6>[ 0.050061] pid_max: default: 32768 minimum: 301 <6>[ 0.054867] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.062167] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.070480] CPU0: update cpu_capacity 1024 <6>[ 0.074683] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.081060] Setting up static identity map for 0x40100000 - 0x40100060 <6>[ 0.087684] rcu: Hierarchical SRCU implementation. <6>[ 0.093069] Detected Renesas RZ/G1 r8a7743 ES3.0 <6>[ 0.098178] smp: Bringing up secondary CPUs ... <6>[ 0.103952] CPU1: update cpu_capacity 1024 <6>[ 0.103960] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <3>[ 0.103967] CPU1: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable <6>[ 0.123396] smp: Brought up 1 node, 2 CPUs <6>[ 0.127597] SMP: Total of 2 processors activated (40.00 BogoMIPS). <6>[ 0.133825] CPU: All CPU(s) started in SVC mode. <6>[ 0.138946] devtmpfs: initialized <6>[ 0.147379] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 <6>[ 0.155187] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.164919] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.176192] pinctrl core: initialized pinctrl subsystem <6>[ 0.182766] NET: Registered protocol family 16 <6>[ 0.188365] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.196020] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.196297] No ATAGs? <6>[ 0.204833] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.212815] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.241147] sh-pfc e6060000.pinctrl: r8a77430_pfc support registered <6>[ 0.256598] vgaarb: loaded <5>[ 0.259738] SCSI subsystem initialized <6>[ 0.263876] usbcore: registered new interface driver usbfs <6>[ 0.269436] usbcore: registered new interface driver hub <6>[ 0.274841] usbcore: registered new device driver usb <6>[ 0.280459] mc: Linux media interface: v0.10 <6>[ 0.284865] videodev: Linux video capture interface: v2.00 <6>[ 0.290452] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.295494] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.304557] PTP clock support registered <6>[ 0.309017] sh_cmt ffca0000.timer: ch0: used for clock events <6>[ 0.314813] sh_cmt ffca0000.timer: ch1: used as clock source <6>[ 0.320540] clocksource: ffca0000.timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 481789878094288 ns <6>[ 0.331209] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.337961] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.889282] NET: Registered protocol family 2 <6>[ 0.893869] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 0.901504] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 0.909850] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 0.917585] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.924763] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.931196] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.937750] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 0.944826] NET: Registered protocol family 1 <6>[ 0.949686] RPC: Registered named UNIX socket transport module. <6>[ 0.955647] RPC: Registered udp transport module. <6>[ 0.960445] RPC: Registered tcp transport module. <6>[ 0.965230] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.971700] PCI: CLS 0 bytes, default 64 <6>[ 0.975888] Unpacking initramfs... <6>[ 1.260430] Freeing initrd memory: 7756K <6>[ 1.264901] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available <6>[ 1.274243] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <5>[ 1.281147] NFS: Registering the id_resolver key type <5>[ 1.286288] Key type id_resolver registered <5>[ 1.290635] Key type id_legacy registered <6>[ 1.294761] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.301481] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.308966] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.316348] io scheduler mq-deadline registered <6>[ 1.320979] io scheduler kyber registered <6>[ 1.327812] gpio_rcar e6050000.gpio: driving 32 GPIOs <6>[ 1.333370] gpio_rcar e6051000.gpio: driving 26 GPIOs <6>[ 1.338758] gpio-946 (touch-interrupt): hogged as input <6>[ 1.344228] gpio_rcar e6052000.gpio: driving 32 GPIOs <6>[ 1.349741] gpio_rcar e6053000.gpio: driving 32 GPIOs <6>[ 1.355264] gpio_rcar e6054000.gpio: driving 32 GPIOs <6>[ 1.360817] gpio_rcar e6055000.gpio: driving 32 GPIOs <6>[ 1.366312] gpio_rcar e6055400.gpio: driving 32 GPIOs <6>[ 1.371817] gpio_rcar e6055800.gpio: driving 26 GPIOs <6>[ 1.378142] pci-rcar-gen2 ee0d0000.pci: host bridge /soc/pci@ee0d0000 ranges: <6>[ 1.385293] pci-rcar-gen2 ee0d0000.pci: MEM 0x00ee0c0000..0x00ee0cffff -> 0x00ee0c0000 <6>[ 1.393658] pci-rcar-gen2 ee0d0000.pci: PCI: revision 11 <6>[ 1.399141] pci-rcar-gen2 ee0d0000.pci: PCI host bridge to bus 0000:01 <6>[ 1.405686] pci_bus 0000:01: root bus resource [bus 01] <6>[ 1.410986] pci_bus 0000:01: root bus resource [mem 0xee0c0000-0xee0cffff] <6>[ 1.417889] pci 0000:01:00.0: [1033:0000] type 00 class 0x060000 <6>[ 1.423952] pci 0000:01:00.0: reg 0x10: [mem 0xee0d0800-0xee0d0bff] <6>[ 1.430257] pci 0000:01:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref] <6>[ 1.437280] pci 0000:01:01.0: [1033:0035] type 00 class 0x0c0310 <6>[ 1.443349] pci 0000:01:01.0: reg 0x10: [mem 0x00000000-0x00000fff] <6>[ 1.449705] pci 0000:01:01.0: supports D1 D2 <6>[ 1.454072] pci 0000:01:01.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.460401] pci 0000:01:02.0: [1033:00e0] type 00 class 0x0c0320 <6>[ 1.466454] pci 0000:01:02.0: reg 0x10: [mem 0x00000000-0x000000ff] <6>[ 1.472811] pci 0000:01:02.0: supports D1 D2 <6>[ 1.477179] pci 0000:01:02.0: PME# supported from D0 D1 D2 D3hot <6>[ 1.484754] PCI: bus1: Fast back to back transfers disabled <6>[ 1.490400] pci 0000:01:01.0: BAR 0: assigned [mem 0xee0c0000-0xee0c0fff] <6>[ 1.497199] pci 0000:01:02.0: BAR 0: assigned [mem 0xee0c1000-0xee0c10ff] <6>[ 1.504033] pci 0000:01:01.0: enabling device (0140 -> 0142) <6>[ 1.509857] pci 0000:01:02.0: enabling device (0140 -> 0142) <6>[ 1.516187] rcar-pcie fe000000.pcie: host bridge /soc/pcie@fe000000 ranges: <6>[ 1.523199] rcar-pcie fe000000.pcie: IO 0x00fe100000..0x00fe1fffff -> 0x0000000000 <6>[ 1.531284] rcar-pcie fe000000.pcie: MEM 0x00fe200000..0x00fe3fffff -> 0x00fe200000 <6>[ 1.539374] rcar-pcie fe000000.pcie: MEM 0x0030000000..0x0037ffffff -> 0x0030000000 <6>[ 1.547433] rcar-pcie fe000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000 <6>[ 1.555518] rcar-pcie fe000000.pcie: IB MEM 0x0040000000..0x00bfffffff -> 0x0040000000 <6>[ 1.563588] rcar-pcie fe000000.pcie: IB MEM 0x0200000000..0x02ffffffff -> 0x0200000000 <6>[ 1.623570] rcar-pcie fe000000.pcie: PCIe link down <4>[ 1.628936] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 1.648574] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled <6>[ 1.655955] SuperH (H)SCI(F) driver initialized <6>[ 1.661129] e6c30000.serial: ttySC3 at MMIO 0xe6c30000 (irq = 88, base_baud = 0) is a scifb <6>[ 1.670124] e6e60000.serial: ttySC0 at MMIO 0xe6e60000 (irq = 89, base_baud = 0) is a scif <6>[ 1.678404] printk: console [ttySC0] enabled <6>[ 1.678404] printk: console [ttySC0] enabled <6>[ 1.687448] printk: bootconsole [scif0] disabled <6>[ 1.687448] printk: bootconsole [scif0] disabled <6>[ 1.704569] renesas_spi e6b10000.spi: DMA available <6>[ 1.710266] spi-nor spi0.0: sst25vf016b (2048 Kbytes) <6>[ 1.716656] renesas_spi e6b10000.spi: probed <6>[ 1.722684] CAN device driver interface <6>[ 1.727460] rcar_can e6e80000.can: device registered (IRQ90) <6>[ 1.736790] ravb e6800000.ethernet eth0: Base address at 0xe6800000, 2e:09:00:00:00:03, IRQ 86. <6>[ 1.746163] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.752976] ehci-pci: EHCI PCI platform driver <6>[ 1.757871] ehci-pci 0000:01:02.0: EHCI Host Controller <6>[ 1.763385] ehci-pci 0000:01:02.0: new USB bus registered, assigned bus number 1 <6>[ 1.771264] ehci-pci 0000:01:02.0: irq 119, io mem 0xee0c1000 <6>[ 1.797942] ehci-pci 0000:01:02.0: USB 2.0 started, EHCI 1.00 <6>[ 1.804532] hub 1-0:1.0: USB hub found <6>[ 1.808593] hub 1-0:1.0: 1 port detected <6>[ 1.813219] ehci-platform: EHCI generic platform driver <6>[ 1.818878] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.825330] ohci-pci: OHCI PCI platform driver <6>[ 1.830197] ohci-pci 0000:01:01.0: OHCI PCI host controller <6>[ 1.836041] ohci-pci 0000:01:01.0: new USB bus registered, assigned bus number 2 <6>[ 1.843870] ohci-pci 0000:01:01.0: irq 119, io mem 0xee0c0000 <6>[ 1.948467] hub 2-0:1.0: USB hub found <6>[ 1.952506] hub 2-0:1.0: 1 port detected <6>[ 1.957101] ohci-platform: OHCI generic platform driver <6>[ 1.963651] renesas_usbhs e6590000.usb: no transceiver found <6>[ 1.969681] renesas_usbhs e6590000.usb: gadget probed <6>[ 1.975123] renesas_usbhs e6590000.usb: probed <4>[ 1.980427] using random self ethernet address <4>[ 1.985136] using random host ethernet address <6>[ 1.990161] usb0: HOST MAC ae:b0:04:04:d4:64 <6>[ 1.994689] usb0: MAC fa:3e:17:18:21:60 <4>[ 1.998814] using random self ethernet address <4>[ 2.003520] using random host ethernet address <6>[ 2.008273] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 <6>[ 2.015144] g_ether gadget: g_ether ready <6>[ 2.019989] i2c /dev entries driver <6>[ 2.025386] bq32k 0-0068: registered as rtc0 <6>[ 2.030330] bq32k 0-0068: setting system clock to 2023-11-08T11:08:19 UTC (1699441699) <6>[ 2.039051] i2c-rcar e6530000.i2c: probed <6>[ 2.087959] rcar_thermal e61f0000.thermal: 1 sensor probed <6>[ 2.096514] sh_mobile_sdhi ee100000.mmc: Got CD GPIO <6>[ 2.096907] usbcore: registered new interface driver usbhid <6>[ 2.102087] usb 1-1: new high-speed USB device number 2 using ehci-pci <6>[ 2.107588] usbhid: USB HID core driver <6>[ 2.115113] sh_mobile_sdhi ee140000.mmc: Got CD GPIO <6>[ 2.123807] sh_mobile_sdhi ee140000.mmc: Got WP GPIO <6>[ 2.129286] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 2.142834] rcar_sound ec500000.sound: probed <6>[ 2.148086] NET: Registered protocol family 10 <6>[ 2.153713] Segment Routing with IPv6 <6>[ 2.157721] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.158013] sh_mmcif ee200000.mmc: Chip version 0x0003, clock rate 12MHz <6>[ 2.164666] NET: Registered protocol family 17 <6>[ 2.175595] can: controller area network core <6>[ 2.180251] NET: Registered protocol family 29 <6>[ 2.184953] can: raw protocol <6>[ 2.188192] can: broadcast manager protocol <6>[ 2.192639] can: netlink gateway - max_hops=1 <5>[ 2.197338] Key type dns_resolver registered <5>[ 2.201972] Registering SWP/SWPB emulation handler <6>[ 2.218407] sh_mobile_sdhi ee100000.mmc: mmc0 base at 0xee100000, max clock rate 195 MHz <6>[ 2.219604] renesas_irqc e61c0000.interrupt-controller: driving 10 irqs <4>[ 2.236323] panel-simple panel: Specify missing connector_type <6>[ 2.244347] sh_mobile_sdhi ee140000.mmc: Got CD GPIO <6>[ 2.249674] sh_mobile_sdhi ee140000.mmc: Got WP GPIO <3>[ 2.254919] edt_ft5x06 0-0038: touchscreen probe failed <6>[ 2.266956] [drm] Initialized rcar-du 1.0.0 20130110 for feb00000.display on minor 0 <6>[ 2.275016] [drm] Device feb00000.display probed <6>[ 2.319919] Console: switching to colour frame buffer device 100x30 <6>[ 2.344399] rcar-du feb00000.display: [drm] fb0: rcar-dudrmfb frame buffer device <6>[ 2.349072] hub 1-1:1.0: USB hub found <6>[ 2.356300] hub 1-1:1.0: 2 ports detected <6>[ 2.361325] sh_mobile_sdhi ee140000.mmc: mmc1 base at 0xee140000, max clock rate 97 MHz <6>[ 2.438001] Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:03: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:03, irq=POLL) <6>[ 2.518045] mmc0: new high speed SDHC card at address aaaa <6>[ 2.524924] mmcblk0: mmc0:aaaa SC32G 29.7 GiB <6>[ 2.534336] mmcblk0: p1 <6>[ 2.677946] usb 1-1.1: new high-speed USB device number 3 using ehci-pci <6>[ 2.690087] mmc2: new high speed MMC card at address 0001 <6>[ 2.696630] mmcblk2: mmc2:0001 MMC04G 3.52 GiB <6>[ 2.701681] mmcblk2boot0: mmc2:0001 MMC04G partition 1 16.0 MiB <6>[ 2.708226] mmcblk2boot1: mmc2:0001 MMC04G partition 2 16.0 MiB <6>[ 2.747968] mmc1: new ultra high speed SDR50 SDHC card at address aaaa <6>[ 2.755760] mmcblk1: mmc1:aaaa SL16G 14.8 GiB (ro) <6>[ 2.766449] mmcblk1: p1 <6>[ 6.620000] ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.628062] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.658003] Sending DHCP requests ., OK <6>[ 8.002206] IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.16 <6>[ 8.010203] IP-Config: Complete: <6>[ 8.013720] device=eth0, hwaddr=2e:09:00:00:00:03, ipaddr=192.168.1.16, mask=255.255.255.0, gw=255.255.255.255 <6>[ 8.024461] host=192.168.1.16, domain=example.org, nis-domain=(none) <6>[ 8.031568] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.031586] nameserver0=192.168.1.1 <6>[ 8.042980] ALSA device list: <6>[ 8.046219] #0: rsnd-dai.0-sgtl5000 <6>[ 8.051613] Freeing unused kernel memory: 1024K <6>[ 8.078387] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.182037] udevd[160]: starting version 3.2.9 <5>[ 8.187266] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.194409] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.201246] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.212376] udevd[160]: specified user 'tss' unknown <27>[ 8.217762] udevd[160]: specified group 'tss' unknown <30>[ 8.225125] udevd[161]: starting eudev-3.2.9 <27>[ 8.248399] udevd[161]: specified user 'tss' unknown <27>[ 8.253856] udevd[161]: specified group 'tss' unknown done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-995808/environment . /lava-995808/environment / # /lava-995808/bin/lava-test-runner /lava-995808/0 /lava-995808/bin/lava-test-runner /lava-995808/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-995808/0/tests/0_dmesg + cat uuid + U<8>[ 15.922133] UID=995808_1.4.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.951406] <8>[ 15.981026] <8>[ 16.013083] + set +x <8>[ 16.022829] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh / # . /lava-995808/environment /lava-995808/bin/lava-test-runner /lava-995808/1 . /lava-995808/environment / # /lava-995808/bin/lava-test-runner /lava-995808/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-995808/1/tests<8>[ 23.019782] /1_bootrr + cat uuid + UUID=995808_1.4.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-995808/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-995808/1/../bin/lava-test-case <8>[ 23.054771] /lava-995808/1/../bin/lava-test-case <8>[ 23.085311] /lava-995808/1/../bin/lava-test-case <8>[ 23.105253] + set +x <8>[ 23.122680] / #