[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.191 (14 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 11386178/tftp-deploy-hjruaq3d/kernel/zImage tftp 0x10000000 11386178/tftp-deploy-hjruaq3d/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11386178/tftp-deploy-hjruaq3d/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ## 3.8 MiB/s done Bytes transferred = 12427776 (bda200 hex) => tftp 0x14000000 11386178/tftp-deploy-hjruaq3d/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 11386178/tftp-deploy-hjruaq3d/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11386178/tftp-deploy-hjruaq3d/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################# 4.1 MiB/s done Bytes transferred = 15505529 (ec9879 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 11386178/tftp-deploy-hjruaq3d/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 11386178/tftp-deploy-hjruaq3d/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.191 Filename '11386178/tftp-deploy-hjruaq3d/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2 MiB/s done Bytes transferred = 42645 (a695 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11386178/extract-nfsrootfs-bknnmjfe,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11386178/extract-nfsrootfs-bknnmjfe,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbda200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15505465 Bytes = 14.8 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d694 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.193-cip38 (KernelCI@build-j28960-arm-gcc-10-multi-v7-defconfig-kselftest-wbsd4) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Aug 30 19:11:25 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/11386178/extract-nfsrootfs-bknnmjfe,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 921320K/1048576K available (17408K kernel code, 2710K rwdata, 8116K rodata, 2048K init, 6692K bss, 61720K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 55511 entries in 163 pages <6>[ 0.000000] ftrace: allocated 163 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000008] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008097] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.022703] Console: colour dummy device 80x30 <4>[ 0.024611] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032620] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036961] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041373] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046010] ... CLASSHASH_SIZE: 4096 <4>[ 0.050597] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055294] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060018] ... CHAINHASH_SIZE: 32768 <4>[ 0.064691] memory used by lock dependency info: 4061 kB <4>[ 0.070368] memory used for stack traces: 2112 kB <4>[ 0.075415] per task-struct memory footprint: 1536 bytes <6>[ 0.081104] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.091778] CPU: Testing write buffer coherency: ok <6>[ 0.096916] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102190] pid_max: default: 32768 minimum: 301 <6>[ 0.107398] LSM: Security Framework initializing <6>[ 0.112011] LSM support for eBPF active <6>[ 0.116167] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123613] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.135080] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141772] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.148256] rcu: Hierarchical SRCU implementation. <6>[ 0.159852] EFI services will not be available. <6>[ 0.162956] smp: Bringing up secondary CPUs ... <6>[ 0.169552] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.169568] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.181463] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.181478] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.193024] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.193040] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.202079] smp: Brought up 1 node, 4 CPUs <6>[ 0.205892] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.212307] CPU: All CPU(s) started in SVC mode. <6>[ 0.219747] devtmpfs: initialized <6>[ 0.267920] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.275524] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.283203] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.295026] pinctrl core: initialized pinctrl subsystem <6>[ 0.304105] DMI not present or invalid. <6>[ 0.307594] NET: Registered protocol family 16 <6>[ 0.319910] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.332757] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.333277] cpuidle: using governor menu <6>[ 0.341352] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.991488] vdd1p1: supplied by regulator-dummy <6>[ 1.020923] vdd3p0: supplied by regulator-dummy <6>[ 1.050001] vdd2p5: supplied by regulator-dummy <6>[ 1.079065] vddarm: supplied by regulator-dummy <6>[ 1.108935] vddpu: supplied by regulator-dummy <6>[ 1.137323] vddsoc: supplied by regulator-dummy <6>[ 2.294358] No ATAGs? <6>[ 2.295190] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.302397] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.325674] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.355692] Serial: AMBA PL011 UART driver <6>[ 2.413410] Kprobes globally optimized <6>[ 2.517901] iommu: Default domain type: Translated <6>[ 2.522405] vgaarb: loaded <5>[ 2.527559] SCSI subsystem initialized <6>[ 2.531029] usbcore: registered new interface driver usbfs <6>[ 2.534741] usbcore: registered new interface driver hub <6>[ 2.540285] usbcore: registered new device driver usb <6>[ 2.552157] i2c i2c-0: IMX I2C adapter registered <6>[ 2.560445] i2c i2c-1: IMX I2C adapter registered <6>[ 2.566610] i2c i2c-2: IMX I2C adapter registered <6>[ 2.572914] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.575311] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.584829] PTP clock support registered <6>[ 2.604153] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.186705] NET: Registered protocol family 2 <6>[ 4.189240] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.199263] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.205340] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.213324] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.222133] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.228585] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.235258] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.241999] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.249813] NET: Registered protocol family 1 <6>[ 4.256371] RPC: Registered named UNIX socket transport module. <6>[ 4.259875] RPC: Registered udp transport module. <6>[ 4.264941] RPC: Registered tcp transport module. <6>[ 4.269783] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.276589] NET: Registered protocol family 44 <6>[ 4.281212] PCI: CLS 0 bytes, default 64 <6>[ 4.287660] Trying to unpack rootfs image as initramfs... <6>[ 6.097071] Freeing initrd memory: 15144K <4>[ 6.099780] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.107103] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.122376] Initialise system trusted keyrings <6>[ 6.125305] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.173421] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.179930] NFS: Registering the id_resolver key type <5>[ 6.182600] Key type id_resolver registered <5>[ 6.186949] Key type id_legacy registered <6>[ 6.191611] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.198199] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.205941] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.212184] Key type asymmetric registered <5>[ 6.214855] Asymmetric key parser 'x509' registered <6>[ 6.220147] bounce: pool size: 64 pages <6>[ 6.224038] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.231637] io scheduler mq-deadline registered <6>[ 6.236405] io scheduler kyber registered <4>[ 6.241449] test_firmware: interface ready <6>[ 6.405326] mxs-dma 110000.dma-apbh: initialized <4>[ 6.465562] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.472706] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 6.685330] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.707570] SuperH (H)SCI(F) driver initialized <6>[ 6.712295] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 6.723049] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 6.729579] printk: console [ttymxc1] enabled <6>[ 6.729579] printk: console [ttymxc1] enabled <6>[ 6.738406] printk: bootconsole [ec_imx21] disabled <6>[ 6.738406] printk: bootconsole [ec_imx21] disabled <6>[ 6.754463] msm_serial: driver initialized <6>[ 6.759849] STMicroelectronics ASC driver initialized <6>[ 6.771256] STM32 USART driver initialized <6>[ 6.796471] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 6.817202] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.825883] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.833766] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.882983] brd: module loaded <6>[ 6.928468] loop: module loaded <6>[ 6.934748] lkdtm: No crash points registered, enable through debugfs <6>[ 6.955887] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 6.964172] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 6.972472] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 6.981024] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 6.989306] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 6.997709] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.005761] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.017187] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.024542] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.033628] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.047789] scsi host0: ahci-imx <6>[ 7.053374] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.113220] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.126606] pps pps0: new PPS source ptp0 <6>[ 7.171279] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.181882] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.187189] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.193614] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.199348] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.225647] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.233473] usbcore: registered new interface driver pegasus <6>[ 7.239673] usbcore: registered new interface driver asix <6>[ 7.245544] usbcore: registered new interface driver ax88179_178a <6>[ 7.252050] usbcore: registered new interface driver cdc_ether <6>[ 7.258430] usbcore: registered new interface driver smsc75xx <6>[ 7.264696] usbcore: registered new interface driver smsc95xx <6>[ 7.270859] usbcore: registered new interface driver net1080 <6>[ 7.276998] usbcore: registered new interface driver cdc_subset <6>[ 7.283333] usbcore: registered new interface driver zaurus <6>[ 7.289478] usbcore: registered new interface driver cdc_ncm <6>[ 7.307338] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.314276] ehci-pci: EHCI PCI platform driver <6>[ 7.319154] ehci-platform: EHCI generic platform driver <6>[ 7.325655] ehci-orion: EHCI orion driver <6>[ 7.330776] SPEAr-ehci: EHCI SPEAr driver <6>[ 7.335909] ehci-st: EHCI STMicroelectronics driver <6>[ 7.341856] ehci-exynos: EHCI Exynos driver <6>[ 7.347138] ehci-atmel: EHCI Atmel driver <6>[ 7.352213] tegra-ehci: Tegra EHCI driver <6>[ 7.357376] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 7.363911] ohci-pci: OHCI PCI platform driver <6>[ 7.368831] ohci-platform: OHCI generic platform driver <6>[ 7.375280] SPEAr-ohci: OHCI SPEAr driver <6>[ 7.380361] ohci-st: OHCI STMicroelectronics driver <6>[ 7.386357] ohci-atmel: OHCI Atmel driver <6>[ 7.394709] usbcore: registered new interface driver usb-storage <6>[ 7.396771] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 7.407062] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 7.413627] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 7.431122] i2c /dev entries driver <6>[ 7.510386] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.516922] sdhci: Copyright(c) Pierre Ossman <6>[ 7.530513] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.543655] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.553286] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 7.558835] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 7.565880] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 7.567056] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 7.581036] usbcore: registered new interface driver usbhid <6>[ 7.586965] usbhid: USB HID core driver <6>[ 7.608592] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 7.608598] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 7.613349] netem: version 1.3 <6>[ 7.613597] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.615857] IPv4 over IPsec tunneling driver <6>[ 7.641228] NET: Registered protocol family 10 <6>[ 7.651274] Segment Routing with IPv6 <6>[ 7.661035] NET: Registered protocol family 17 <6>[ 7.662019] mmc2: new high speed SDHC card at address 0001 <5>[ 7.667493] Key type dns_resolver registered <6>[ 7.675388] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 7.688902] ThumbEE CPU extension supported. <5>[ 7.693503] Registering SWP/SWPB emulation handler <5>[ 7.699972] Loading compiled-in X.509 certificates <4>[ 7.703378] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 7.712930] GPT:29296874 != 30965759 <4>[ 7.716870] GPT:Alternate GPT header not at the end of the disk. <4>[ 7.723178] GPT:29296874 != 30965759 <4>[ 7.727113] GPT: Use GNU Parted to correct GPT errors. <6>[ 7.732621] mmcblk2: p1 p2 p3 <4>[ 7.894691] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.903349] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.917521] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.956202] imx_usb 2184200.usb: No over current polarity defined <6>[ 7.969868] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 7.975521] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.005635] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.025442] hub 1-0:1.0: USB hub found <6>[ 8.031440] hub 1-0:1.0: 1 port detected <3>[ 8.046969] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 8.054653] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 8.063098] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 8.092198] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.100960] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.115103] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.148206] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.156825] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.170924] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.191259] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.222416] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.231060] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.245175] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.269155] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 8.454580] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 8.662425] hub 1-1:1.0: USB hub found <6>[ 8.668351] hub 1-1:1.0: 3 ports detected <4>[ 8.698070] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.706731] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.721037] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 10.335973] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 10.354309] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 10.385319] Sending DHCP requests ., OK <6>[ 10.428892] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.191 <6>[ 10.437496] IP-Config: Complete: <6>[ 10.441061] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.191, mask=255.255.255.0, gw=192.168.201.1 <6>[ 10.451939] host=192.168.201.191, domain=lava-rack, nis-domain=(none) <6>[ 10.459157] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 10.459178] nameserver0=192.168.201.1 <6>[ 10.527541] Freeing unused kernel memory: 2048K <6>[ 10.535227] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 14.912509] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 14.950503] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.968581] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.987515] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 15.001975] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.029764] CAN device driver interface <4>[ 15.041606] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.050330] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.076173] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.096351] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <4>[ 15.098684] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.115201] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.122052] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <4>[ 15.186247] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.201956] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.250384] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 15.264391] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 15.270833] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 15.285250] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <4>[ 15.299264] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.350457] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 15.351038] caam 2100000.crypto: Entropy delay = 3200 <4>[ 15.359317] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.386624] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.424522] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 15.453963] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.473265] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.485290] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.490884] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 15.497954] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 15.526316] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.547445] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.556676] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.562132] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 15.566010] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.574253] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.582108] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.586606] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.587455] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 15.588086] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 15.595805] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.622436] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.644393] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 15.645123] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.653145] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 15.668654] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.683222] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 15.725685] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.734979] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.743860] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.752734] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.781358] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.790212] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.835889] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.884313] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.893207] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.902547] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.911355] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.936429] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.945219] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.607022] caam algorithms registered in /proc/crypto <6>[ 16.619079] caam 2100000.crypto: registering rng-caam <5>[ 16.747998] random: crng init done <4>[ 16.759542] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.794190] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.802890] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.811729] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.820533] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.845436] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.855129] panel-simple panel-lcd: Specify missing connector_type Begin: Loading essential drivers ... done. <4>[ 16.870994] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available <6>[ 16.902992] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.911884] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) Device /sys/class/net/eth0 found<6>[ 16.920956] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) done. <6>[ 16.931868] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) IP-Config: eth0 hardware address 0e:cc:7b:b0:7c:c7 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.191 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 18.950121] systemd[1]: System time before build time, advancing clock. <30>[ 19.234225] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 19.260735] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 19.332173] systemd[1]: Set hostname to . <30>[ 21.206971] systemd[1]: Queued start job for default target Graphical Interface. <30>[ 21.222174] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 21.270121] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 21.319820] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 21.369303] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 21.419103] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 21.468389] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 21.516616] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 21.529807] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 21.576546] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 21.614645] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 21.655104] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 21.696119] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 21.736416] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 21.838615] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 21.857753] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 21.911117] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 21.961301] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 22.016651] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 22.069359] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 22.118289] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 22.129480] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 22.149933] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 22.196346] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 22.251927] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 22.306206] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 22.356398] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 22.417073] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 22.475966] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <6>[ 22.514435] fuse: init (API version 7.32) <30>[ 22.518433] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 22.600876] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 22.649492] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 22.709807] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 22.775804] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 22.819251] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 22.868240] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 22.968406] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 22.979377] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 23.020785] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 23.031372] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 23.080914] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 23.091960] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 23.140526] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 23.180186] systemd[1]: Finished Remount Root and Kernel File Systems. [ OK ] Finished Remount Root and Kernel File Systems. <30>[ 23.238550] systemd[1]: Mounting FUSE Control File System... Mounting FUSE Control File System... <30>[ 23.287487] systemd[1]: Mounting Kernel Configuration File System... Mounting Kernel Configuration File System... <30>[ 23.326916] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. <30>[ 23.338834] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. <30>[ 23.361241] systemd[1]: Starting Load/Save Random Seed... Starting Load/Save Random Seed... <30>[ 23.417665] systemd[1]: Starting Apply Kernel Variables... Starting Apply Kernel Variables... <30>[ 23.472278] systemd[1]: Starting Create System Users... Starting Create System Users... <30>[ 23.523354] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. Starting Flush Journal to Persistent Storage... [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... <46>[ 23.936083] systemd-journald[281]: Received client request to flush runtime journal. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.193-cip38 #1 SMP Wed Aug 30 19:11:25 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11386178/extract-nfsrootfs-bknnmjfe' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/11386178/extract-nfsrootfs-bknnmjfe' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-11386178/environment . /lava-11386178/environment / # /lava-11386178/bin/lava-test-runner /lava-11386178/0 /lava-11386178/bin/lava-test-runner /lava-11386178/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-11386178/0/tests/0_timesync-off ++ cat uuid + UUID=11386178_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-livepatch + TESTRUN_ID=1_kselftest-livepatch + cd /lava-11386178/0/tests/1_kselftest-livepatch ++ cat uuid + UUID=11386178_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c livepatch -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.191-cip38-218-g9947ff6f0dba7/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-08-30 19:31:36-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.191-cip38-218-g9947ff6f0dba7/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1408280 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 49.22K 188KB/s kselftest.tar.xz 15%[==> ] 218.91K 415KB/s kselftest.tar.xz 60%[===========> ] 826.96K 997KB/s kselftest.tar.xz 100%[===================>] 1.34M 1.38MB/s in 1.0s 2023-08-30 19:31:38 (1.38 MB/s) - 'kselftest.tar.xz' saved [1408280/1408280] skiplist: ======================================== ======================================== livepatch:test-livepatch.sh livepatch:test-callbacks.sh livepatch:test-shadow-vars.sh livepatch:test-state.sh livepatch:test-ftrace.sh ============== Tests to run =============== livepatch:test-livepatch.sh livepatch:test-callbacks.sh livepatch:test-shadow-vars.sh livepatch:test-state.sh livepatch:test-ftrace.sh ===========End Tests to run =============== shardfile-livepatch pass <12>[ 59.839788] kselftest: Running tests in livepatch TAP version 13 1..5 # selftests: livepatch: test-livepatch.sh <12>[ 60.527550] livepatch: kernel.ftrace_enabled = 1 <12>[ 60.636827] ===== TEST: basic function patching ===== # TEST: basic function patching ... <12>[ 60.717543] SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 1 selftests: livepatch: test-livepatch.sh # SKIP # selftests: livepatch: test-callbacks.sh <12>[ 61.270078] livepatch: kernel.ftrace_enabled = 1 # <12>[ 61.361657] ===== TEST: target module before livepatch ===== TEST: target module before livepatch ... <12>[ 61.422994] SKIP: unable to load module test_klp_callbacks_mod, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_callbacks_mod, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 2 selftests: livepatch: test-callbacks.sh # SKIP # selftests: livepatch: test-shadow-vars.sh <12>[ 61.957398] livepatch: kernel.ftrace_enabled = 1 # TE<12>[ 62.069294] ===== TEST: basic shadow variable API ===== ST: basic shadow variable API ... <12>[ 62.131013] SKIP: unable to load module test_klp_shadow_vars, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_shadow_vars, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 3 selftests: livepatch: test-shadow-vars.sh # SKIP # selftests: livepatch: test-state.sh <12>[ 62.678520] livepatch: kernel.ftrace_enabled = 1 # TE<12>[ 62.779918] ===== TEST: system state modification ===== ST: system state modification ... <12>[ 62.841069] SKIP: unable to load module test_klp_state, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_state, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 4 selftests: livepatch: test-state.sh # SKIP # selftests: livepatch: test-ftrace.sh <12>[ 63.368786] livepatch: kernel.ftrace_enabled = 1 # T<12>[ 63.460006] ===== TEST: livepatch interaction with ftrace_enabled sysctl ===== EST: livepatch interaction with ftrace_enabled sysctl ... <12>[ 63.519234] livepatch: kernel.ftrace_enabled = 0 <12>[ 63.525217] % modprobe test_klp_livepatch <12>[ 63.591825] modprobe: FATAL: Module test_klp_livepatch not found in directory /lib/modules/5.10.193-cip38 <12>[ 63.666469] livepatch: kernel.ftrace_enabled = 1 <12>[ 63.728831] SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 5 selftests: livepatch: test-ftrace.sh # SKIP livepatch_test-livepatch_sh skip livepatch_test-callbacks_sh skip livepatch_test-shadow-vars_sh skip livepatch_test-state_sh skip livepatch_test-ftrace_sh skip + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #