Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot 2019.04-lf-5.4.y_v2019.04+g228843cdf5 (Feb 24 2020 - 11:58:52 +0000) CPU: Freescale i.MX6UL rev1.2 696 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 33C Reset cause: POR Model: Freescale i.MX6 UltraLite 14x14 EVK Board Board: MX6UL 14x14 EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: Warning: ethernet@020b4000 using MAC address from ROM eth1: ethernet@020b4000 [PRIME] Warning: ethernet@02188000 using MAC address from ROM , eth0: ethernet@02188000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.212 (1295 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp ${loadaddr} 1248119/tftp-deploy-qbcx41d_/kernel/zImage tftp ${loadaddr} 1248119/tftp-deploy-qbcx41d_/kernel/zImage Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.212; sending through gateway 172.16.1.4 Filename '1248119/tftp-deploy-qbcx41d_/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 5.1 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp ${initrd_addr} 1248119/tftp-deploy-qbcx41d_/ramdisk/ramdisk.cpio.gz.uboot tftp ${initrd_addr} 1248119/tftp-deploy-qbcx41d_/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.212; sending through gateway 172.16.1.4 Filename '1248119/tftp-deploy-qbcx41d_/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 4.8 MiB/s done Bytes transferred = 16085392 (f57190 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp ${fdt_addr} 1248119/tftp-deploy-qbcx41d_/dtb/imx6ul-14x14-evk.dtb tftp ${fdt_addr} 1248119/tftp-deploy-qbcx41d_/dtb/imx6ul-14x14-evk.dtb Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.212; sending through gateway 172.16.1.4 Filename '1248119/tftp-deploy-qbcx41d_/dtb/imx6ul-14x14-evk.dtb'. Load address: 0x83000000 Loading: *### 3.7 MiB/s done Bytes transferred = 30953 (78e9 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz ${loadaddr} ${initrd_addr} ${fdt_addr} bootz ${loadaddr} ${initrd_addr} ${fdt_addr} Kernel image @ 0x80800000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16085328 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300a8e8 ft_system_setup for mx6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.193-cip38 (KernelCI@build-j28955-arm-gcc-10-multi-v7-defconfig-f97tr) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Aug 30 19:07:02 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 UltraLite 14x14 EVK Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 413008K/524288K available (14336K kernel code, 2239K rwdata, 5360K rodata, 2048K init, 424K bss, 45744K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] Switching to timer-based delay loop, resolution 41ns <6>[ 0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008101] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.025069] Console: colour dummy device 80x30 <6>[ 0.027029] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.037643] CPU: Testing write buffer coherency: ok <6>[ 0.042699] pid_max: default: 32768 minimum: 301 <6>[ 0.047936] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.055148] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.065244] CPU0: update cpu_capacity 1024 <6>[ 0.067497] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.075234] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.082645] rcu: Hierarchical SRCU implementation. <6>[ 0.091002] EFI services will not be available. <6>[ 0.093396] smp: Bringing up secondary CPUs ... <6>[ 0.097847] smp: Brought up 1 node, 1 CPU <6>[ 0.102022] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.108494] CPU: All CPU(s) started in SVC mode. <6>[ 0.114383] devtmpfs: initialized <6>[ 0.130787] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.136410] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.146144] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.157894] pinctrl core: initialized pinctrl subsystem <6>[ 0.164268] DMI not present or invalid. <6>[ 0.167725] NET: Registered protocol family 16 <6>[ 0.174956] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.184865] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.185063] cpuidle: using governor menu <6>[ 0.429396] vdd3p0: supplied by regulator-dummy <6>[ 0.443920] cpu: supplied by regulator-dummy <6>[ 0.458743] vddsoc: supplied by regulator-dummy <6>[ 0.877533] No ATAGs? <6>[ 0.878656] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.885596] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.900371] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.914818] Serial: AMBA PL011 UART driver <6>[ 0.988441] iommu: Default domain type: Translated <6>[ 0.991588] vgaarb: loaded <5>[ 0.995864] SCSI subsystem initialized <6>[ 0.999123] usbcore: registered new interface driver usbfs <6>[ 1.003586] usbcore: registered new interface driver hub <6>[ 1.009232] usbcore: registered new device driver usb <6>[ 1.017774] i2c i2c-0: IMX I2C adapter registered <6>[ 1.022038] i2c i2c-1: IMX I2C adapter registered <6>[ 1.027704] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.030246] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.039545] PTP clock support registered <6>[ 1.052227] clocksource: Switched to clocksource mxc_timer1 <6>[ 3.308740] NET: Registered protocol family 2 <6>[ 3.311047] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 3.320009] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 3.326778] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 3.334777] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 3.342218] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 3.348829] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 3.355553] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 3.363117] NET: Registered protocol family 1 <6>[ 3.369049] RPC: Registered named UNIX socket transport module. <6>[ 3.373581] RPC: Registered udp transport module. <6>[ 3.378393] RPC: Registered tcp transport module. <6>[ 3.383403] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 3.390065] PCI: CLS 0 bytes, default 64 <6>[ 3.395348] Trying to unpack rootfs image as initramfs... <6>[ 6.392705] Freeing initrd memory: 15712K <6>[ 6.395559] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 6.406289] Initialise system trusted keyrings <6>[ 6.408967] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 6.431421] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.436806] NFS: Registering the id_resolver key type <5>[ 6.440146] Key type id_resolver registered <5>[ 6.444547] Key type id_legacy registered <6>[ 6.448995] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.455732] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.463444] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.469184] Key type asymmetric registered <5>[ 6.472376] Asymmetric key parser 'x509' registered <6>[ 6.477513] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.485128] io scheduler mq-deadline registered <6>[ 6.489855] io scheduler kyber registered <4>[ 6.546640] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 6.580826] mxs-dma 1804000.dma-apbh: initialized <4>[ 6.612024] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.619161] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 6.754382] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.768470] SuperH (H)SCI(F) driver initialized <6>[ 6.772689] printk: console [ttymxc0] enabled <6>[ 6.772689] printk: console [ttymxc0] enabled <6>[ 6.779910] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.779910] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.793174] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 73, base_baud = 5000000) is a IMX <6>[ 6.805469] msm_serial: driver initialized <6>[ 6.810487] STMicroelectronics ASC driver initialized <6>[ 6.819984] STM32 USART driver initialized <4>[ 6.845999] panel-simple panel: supply power not found, using dummy regulator <6>[ 6.879064] brd: module loaded <6>[ 6.897563] loop: module loaded <6>[ 6.936788] CAN device driver interface <6>[ 6.943886] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 6.953312] pps pps0: new PPS source ptp0 <6>[ 7.102798] fec 20b4000.ethernet eth0: registered PHC device 0 <6>[ 7.112473] pps pps1: new PPS source ptp1 <6>[ 9.356628] fec 2188000.ethernet eth1: registered PHC device 1 <6>[ 9.365856] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 9.371122] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 9.377623] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 9.383372] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 9.402694] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 9.410542] usbcore: registered new interface driver pegasus <6>[ 9.416697] usbcore: registered new interface driver asix <6>[ 9.422538] usbcore: registered new interface driver ax88179_178a <6>[ 9.429001] usbcore: registered new interface driver cdc_ether <6>[ 9.435292] usbcore: registered new interface driver smsc75xx <6>[ 9.441459] usbcore: registered new interface driver smsc95xx <6>[ 9.447653] usbcore: registered new interface driver net1080 <6>[ 9.453744] usbcore: registered new interface driver cdc_subset <6>[ 9.460028] usbcore: registered new interface driver zaurus <6>[ 9.466152] usbcore: registered new interface driver cdc_ncm <6>[ 9.480062] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 9.487027] ehci-pci: EHCI PCI platform driver <6>[ 9.491885] ehci-platform: EHCI generic platform driver <6>[ 9.498179] ehci-orion: EHCI orion driver <6>[ 9.503121] SPEAr-ehci: EHCI SPEAr driver <6>[ 9.507844] ehci-st: EHCI STMicroelectronics driver <6>[ 9.513541] ehci-exynos: EHCI Exynos driver <6>[ 9.518430] ehci-atmel: EHCI Atmel driver <6>[ 9.523245] tegra-ehci: Tegra EHCI driver <6>[ 9.528014] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 9.534617] ohci-pci: OHCI PCI platform driver <6>[ 9.539484] ohci-platform: OHCI generic platform driver <6>[ 9.545702] SPEAr-ohci: OHCI SPEAr driver <6>[ 9.550457] ohci-st: OHCI STMicroelectronics driver <6>[ 9.556205] ohci-atmel: OHCI Atmel driver <6>[ 9.563547] usbcore: registered new interface driver usb-storage <6>[ 9.588784] i2c /dev entries driver <6>[ 9.640670] sdhci: Secure Digital Host Controller Interface driver <6>[ 9.647305] sdhci: Copyright(c) Pierre Ossman <6>[ 9.658319] Synopsys Designware Multimedia Card Interface Driver <6>[ 9.669366] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 9.688418] sdhci-esdhc-imx 2190000.mmc: Got CD GPIO <6>[ 9.699640] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 9.708612] usbcore: registered new interface driver usbhid <6>[ 9.714597] usbhid: USB HID core driver <6>[ 9.734990] NET: Registered protocol family 10 <6>[ 9.742682] Segment Routing with IPv6 <6>[ 9.746837] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 9.754641] NET: Registered protocol family 17 <6>[ 9.759409] can: controller area network core <6>[ 9.764354] NET: Registered protocol family 29 <6>[ 9.769090] can: raw protocol <6>[ 9.772418] can: broadcast manager protocol <6>[ 9.776905] can: netlink gateway - max_hops=1 <5>[ 9.782703] Key type dns_resolver registered <6>[ 9.791400] ThumbEE CPU extension supported. <5>[ 9.796138] Registering SWP/SWPB emulation handler <5>[ 9.802881] Loading compiled-in X.509 certificates <6>[ 9.833874] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <4>[ 9.845616] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 9.855073] mmc0: SDHCI controller on 2190000.mmc [2190000.mmc] using ADMA <4>[ 9.866434] panel-simple panel: supply power not found, using dummy regulator <4>[ 9.878333] imx_usb 2184000.usb: No over current polarity defined <6>[ 9.902368] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 9.907626] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.945171] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 9.955036] hub 1-0:1.0: USB hub found <6>[ 9.959283] hub 1-0:1.0: 1 port detected <6>[ 9.970639] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 9.992124] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 10.001733] mmc1: host does not support reading read-only switch, assuming write-enable <4>[ 10.013998] panel-simple panel: supply power not found, using dummy regulator <6>[ 10.022375] mmc1: new high speed SDHC card at address aaaa <4>[ 10.034195] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 10.043825] mmcblk1: mmc1:aaaa SS16G 14.8 GiB <4>[ 10.052493] panel-simple panel: supply power not found, using dummy regulator <6>[ 10.072293] mmcblk1: p1 p2 <4>[ 10.081663] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 10.096280] panel-simple panel: supply power not found, using dummy regulator <6>[ 10.180497] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) <6>[ 10.280401] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:02: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:02, irq=POLL) <6>[ 13.365518] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 13.385529] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 13.414730] Sending DHCP requests .., OK <6>[ 16.119372] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.212 <6>[ 16.127383] IP-Config: Complete: <6>[ 16.130943] device=eth0, hwaddr=00:04:9f:05:20:41, ipaddr=172.16.1.212, mask=255.255.255.0, gw=172.16.1.4 <6>[ 16.141381] host=172.16.1.212, domain=example.org, nis-domain=(none) <6>[ 16.148559] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 16.148586] nameserver0=172.16.1.4 <6>[ 16.174403] Freeing unused kernel memory: 2048K <6>[ 16.185094] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 16.436231] udevd[126]: starting version 3.2.9 <5>[ 16.443644] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.450898] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 16.458637] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 16.479991] udevd[126]: specified user 'tss' unknown <27>[ 16.486066] udevd[126]: specified group 'tss' unknown <30>[ 16.504347] udevd[127]: starting eudev-3.2.9 <4>[ 19.796406] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 19.936017] panel-simple panel: supply power not found, using dummy regulator <6>[ 20.490826] caam 2140000.crypto: RNG4 SH0 was previously instantiated without prediction resistance. Tearing it down <6>[ 20.501821] caam 2140000.crypto: Deinstantiated RNG4 SH0 <6>[ 20.507518] caam 2140000.crypto: Instantiated RNG4 SH0 <6>[ 20.512963] caam 2140000.crypto: RNG4 SH1 was previously instantiated without prediction resistance. Tearing it down <6>[ 20.523795] caam 2140000.crypto: Deinstantiated RNG4 SH1 <6>[ 20.529397] caam 2140000.crypto: Instantiated RNG4 SH1 <6>[ 20.534845] caam 2140000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 20.541731] caam 2140000.crypto: job rings = 3, qi = 0 <4>[ 20.562791] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 20.577353] panel-simple panel: supply power not found, using dummy regulator <6>[ 21.329183] spi-nor spi4.0: n25q256a (32768 Kbytes) <4>[ 21.382463] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 21.419912] panel-simple panel: supply power not found, using dummy regulator <6>[ 21.572989] gpio@0 enforce active low on chipselect handle <4>[ 21.638609] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 21.697013] panel-simple panel: supply power not found, using dummy regulator <6>[ 23.271211] caam algorithms registered in /proc/crypto <6>[ 23.279795] caam 2140000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 23.287623] caam 2140000.crypto: registering rng-caam <4>[ 23.302656] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.318455] panel-simple panel: supply power not found, using dummy regulator <5>[ 23.343134] random: crng init done <4>[ 23.358297] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.373527] panel-simple panel: supply power not found, using dummy regulator <4>[ 23.420737] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 23.446045] panel-simple panel: supply power not found, using dummy regulator done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1248119/environment . /lava-1248119/environment / # /lava-1248119/bin/lava-test-runner /lava-1248119/0 /lava-1248119/bin/lava-test-runner /lava-1248119/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1248119/0/tests/0_dmesg + cat uuid + UUID=1248119_1.5.2.4.1<8>[ 29.523879] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 29.590036] <8>[ 29.651061] <8>[ 29.711895] + set +x <8>[ 29.723450] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1248119/environment / # . /lava-1248119/environment/lava-1248119/bin/lava-test-runner /lava-1248119/1 / # /lava-1248119/bin/lava-test-runner /lava-1248119/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1248119/1/tests/1_bootrr + cat uuid + UUID=1248119_1.5.2.4.5<8>[ 35.470247] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1248119/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto regulator-can-3v3 sound backlight-display panel 2090000.flexcan 2094000.flexcan 21c8000.lcdif /lava-1248119/1/../bin/lava-test-case <8>[ 36.573373] /lava-1248119/1/../bin/lava-test-case <8>[ 36.629804] /lava-1248119/1/../bin/lava-test-case <8>[ 36.664308] + set +x <8>[ 36.689436] / #