Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 26C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.217 (1312 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp ${loadaddr} 1259747/tftp-deploy-9adeff2q/kernel/zImage tftp ${loadaddr} 1259747/tftp-deploy-9adeff2q/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.217; sending through gateway 172.16.1.4 Filename '1259747/tftp-deploy-9adeff2q/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 10.4 MiB/s done Bytes transferred = 12542464 (bf6200 hex) => tftp ${initrd_addr} 1259747/tftp-deploy-9adeff2q/ramdisk/ramdisk.cpio.gz.uboot tftp ${initrd_addr} 1259747/tftp-deploy-9adeff2q/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.217; sending through gateway 172.16.1.4 Filename '1259747/tftp-deploy-9adeff2q/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############## 9.8 MiB/s done Bytes transferred = 19275219 (1261dd3 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp ${fdt_addr} 1259747/tftp-deploy-9adeff2q/dtb/imx7d-sdb.dtb tftp ${fdt_addr} 1259747/tftp-deploy-9adeff2q/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.217; sending through gateway 172.16.1.4 Filename '1259747/tftp-deploy-9adeff2q/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 6.1 MiB/s done Bytes transferred = 38204 (953c hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz ${loadaddr} ${initrd_addr} ${fdt_addr} bootz ${loadaddr} ${initrd_addr} ${fdt_addr} Kernel image @ 0x80800000 [ 0x000000 - 0xbf6200 ] ## Loading init Ramdisk from Legacy Image at 83800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19275155 Bytes = 18.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300c53b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.201-cip40 (KernelCI@build-j20325-arm-gcc-10-multi-v7-defconfig-kselftest-zkzrq) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Nov 22 18:37:22 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000afffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x00000000b0000000-0x00000000bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x00000000bfffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917832K/1048576K available (17408K kernel code, 2714K rwdata, 8140K rodata, 2048K init, 6693K bss, 65208K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] ftrace: allocating 56130 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000011] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008297] Switching to timer-based delay loop, resolution 125ns <6>[ 0.016382] Switching to timer-based delay loop, resolution 41ns <6>[ 0.020989] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029125] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.044750] Console: colour dummy device 80x30 <4>[ 0.046679] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.054742] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.059075] ... MAX_LOCK_DEPTH: 48 <4>[ 0.063537] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.068209] ... CLASSHASH_SIZE: 4096 <4>[ 0.072812] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.077537] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.082294] ... CHAINHASH_SIZE: 32768 <4>[ 0.086987] memory used by lock dependency info: 4061 kB <4>[ 0.092706] memory used for stack traces: 2112 kB <4>[ 0.097750] per task-struct memory footprint: 1536 bytes <6>[ 0.103539] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.114150] CPU: Testing write buffer coherency: ok <6>[ 0.119281] pid_max: default: 32768 minimum: 301 <6>[ 0.124557] LSM: Security Framework initializing <6>[ 0.129166] LSM support for eBPF active <6>[ 0.133302] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.140863] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.152789] CPU0: update cpu_capacity 1024 <6>[ 0.154339] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.164177] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.170534] rcu: Hierarchical SRCU implementation. <6>[ 0.183260] EFI services will not be available. <6>[ 0.186266] smp: Bringing up secondary CPUs ... <6>[ 0.193344] smp: Brought up 1 node, 1 CPU <6>[ 0.194805] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.201446] CPU: All CPU(s) started in SVC mode. <6>[ 0.208799] devtmpfs: initialized <6>[ 0.262813] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.269241] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.278360] futex hash table entries: 512 (order: 3, 32768 bytes, linear) <6>[ 0.289677] pinctrl core: initialized pinctrl subsystem <6>[ 0.299718] DMI not present or invalid. <6>[ 0.303754] NET: Registered protocol family 16 <6>[ 0.316789] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.332320] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.332590] cpuidle: using governor menu <6>[ 0.342265] No ATAGs? <6>[ 0.343154] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.351143] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.365993] Serial: AMBA PL011 UART driver <6>[ 0.610146] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <6>[ 0.621061] imx7d-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.743363] Kprobes globally optimized <6>[ 0.867120] iommu: Default domain type: Translated <6>[ 0.874514] vgaarb: loaded <5>[ 0.879306] SCSI subsystem initialized <6>[ 0.882820] usbcore: registered new interface driver usbfs <6>[ 0.886554] usbcore: registered new interface driver hub <6>[ 0.892149] usbcore: registered new device driver usb <6>[ 0.927966] i2c i2c-0: IMX I2C adapter registered <6>[ 0.953211] i2c i2c-1: IMX I2C adapter registered <6>[ 0.957890] i2c i2c-2: IMX I2C adapter registered <6>[ 0.983222] i2c i2c-3: IMX I2C adapter registered <6>[ 0.989807] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.992224] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.001823] PTP clock support registered <6>[ 1.023224] clocksource: Switched to clocksource arch_sys_counter <6>[ 2.940096] NET: Registered protocol family 2 <6>[ 2.942571] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.952317] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 2.958589] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.966677] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 2.975551] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.981641] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 2.988757] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 2.995517] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 3.003393] NET: Registered protocol family 1 <6>[ 3.011330] RPC: Registered named UNIX socket transport module. <6>[ 3.014914] RPC: Registered udp transport module. <6>[ 3.019742] RPC: Registered tcp transport module. <6>[ 3.024786] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 3.031492] NET: Registered protocol family 44 <6>[ 3.036292] PCI: CLS 0 bytes, default 64 <6>[ 3.043197] Trying to unpack rootfs image as initramfs... <6>[ 5.587391] Freeing initrd memory: 18824K <6>[ 5.591404] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 5.605903] Initialise system trusted keyrings <6>[ 5.609051] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 5.671518] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 5.678991] NFS: Registering the id_resolver key type <5>[ 5.681647] Key type id_resolver registered <5>[ 5.686060] Key type id_legacy registered <6>[ 5.690929] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 5.697408] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 5.705175] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 5.711932] Key type asymmetric registered <5>[ 5.714128] Asymmetric key parser 'x509' registered <6>[ 5.719553] bounce: pool size: 64 pages <6>[ 5.723436] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 5.730999] io scheduler mq-deadline registered <6>[ 5.735810] io scheduler kyber registered <4>[ 5.740985] test_firmware: interface ready <4>[ 5.849660] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 5.915430] mxs-dma 33000000.dma-controller: initialized <4>[ 5.973650] imx-sdma 30bd0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <6>[ 5.981812] imx-sdma 30bd0000.dma-controller: external firmware not found, using ROM firmware <6>[ 6.260960] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.285412] SuperH (H)SCI(F) driver initialized <3>[ 6.289585] clk: failed to reparent uart1_src to pll_sys_main_240m_clk: -16 <6>[ 6.295813] 30860000.serial: ttymxc0 at MMIO 0x30860000 (irq = 58, base_baud = 1500000) is a IMX <6>[ 6.304356] printk: console [ttymxc0] enabled <6>[ 6.304356] printk: console [ttymxc0] enabled <6>[ 6.312980] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.312980] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.328347] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 67, base_baud = 15000000) is a IMX <6>[ 6.344163] msm_serial: driver initialized <6>[ 6.349528] STMicroelectronics ASC driver initialized <6>[ 6.360963] STM32 USART driver initialized <6>[ 6.387096] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <6>[ 6.455777] brd: module loaded <6>[ 6.502428] loop: module loaded <6>[ 6.509471] lkdtm: No crash points registered, enable through debugfs <6>[ 6.586496] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 6.605366] pps pps0: new PPS source ptp0 <3>[ 6.612670] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 6.619933] fec 30bf0000.ethernet: Using random MAC address: e6:0b:bd:eb:a4:76 <6>[ 8.235020] fec 30bf0000.ethernet eth0: registered PHC device 0 <6>[ 8.245745] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 8.251013] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 8.257557] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 8.263306] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 8.289908] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 8.297834] usbcore: registered new interface driver pegasus <6>[ 8.304069] usbcore: registered new interface driver asix <6>[ 8.309918] usbcore: registered new interface driver ax88179_178a <6>[ 8.316539] usbcore: registered new interface driver cdc_ether <6>[ 8.322892] usbcore: registered new interface driver smsc75xx <6>[ 8.329214] usbcore: registered new interface driver smsc95xx <6>[ 8.335506] usbcore: registered new interface driver net1080 <6>[ 8.341615] usbcore: registered new interface driver cdc_subset <6>[ 8.348057] usbcore: registered new interface driver zaurus <6>[ 8.354260] usbcore: registered new interface driver cdc_ncm <6>[ 8.372357] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 8.379348] ehci-pci: EHCI PCI platform driver <6>[ 8.384307] ehci-platform: EHCI generic platform driver <6>[ 8.390744] ehci-orion: EHCI orion driver <6>[ 8.395939] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.401020] ehci-st: EHCI STMicroelectronics driver <6>[ 8.407102] ehci-exynos: EHCI Exynos driver <6>[ 8.412356] ehci-atmel: EHCI Atmel driver <6>[ 8.417494] tegra-ehci: Tegra EHCI driver <6>[ 8.422614] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.429217] ohci-pci: OHCI PCI platform driver <6>[ 8.434195] ohci-platform: OHCI generic platform driver <6>[ 8.440582] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.445757] ohci-st: OHCI STMicroelectronics driver <6>[ 8.451719] ohci-atmel: OHCI Atmel driver <6>[ 8.460194] usbcore: registered new interface driver usb-storage <6>[ 8.498274] i2c /dev entries driver <3>[ 8.580405] CPUidle arm: CPU 0 failed to init idle CPU ops <6>[ 8.588796] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.595340] sdhci: Copyright(c) Pierre Ossman <6>[ 8.608964] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.622216] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.645939] sdhci-esdhc-imx 30b40000.mmc: Got CD GPIO <6>[ 8.651523] sdhci-esdhc-imx 30b40000.mmc: Got WP GPIO <6>[ 8.678393] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.688677] usbcore: registered new interface driver usbhid <6>[ 8.694642] usbhid: USB HID core driver <6>[ 8.722771] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.731312] IPv4 over IPsec tunneling driver <6>[ 8.741498] NET: Registered protocol family 10 <6>[ 8.752492] Segment Routing with IPv6 <6>[ 8.763297] NET: Registered protocol family 17 <6>[ 8.769531] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <6>[ 8.781259] mmc0: SDHCI controller on 30b40000.mmc [30b40000.mmc] using ADMA <6>[ 8.791235] 8021q: 802.1Q VLAN Support v1.8 <5>[ 8.797044] Key type dns_resolver registered <6>[ 8.801799] ThumbEE CPU extension supported. <5>[ 8.806490] Registering SWP/SWPB emulation handler <5>[ 8.813646] Loading compiled-in X.509 certificates <4>[ 9.187866] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 9.259096] imx_usb 30b10000.usb: No over current polarity defined <4>[ 9.275601] imx_usb 30b20000.usb: No over current polarity defined <6>[ 9.294005] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <4>[ 9.317618] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 9.390619] imx_usb 30b10000.usb: No over current polarity defined <4>[ 9.406806] imx_usb 30b20000.usb: No over current polarity defined <4>[ 9.438330] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 9.508692] imx_usb 30b10000.usb: No over current polarity defined <4>[ 9.524819] imx_usb 30b20000.usb: No over current polarity defined <6>[ 9.543548] mmc0: new high speed SDHC card at address aaaa <6>[ 9.554325] mmcblk0: mmc0:aaaa SA16G 14.8 GiB <6>[ 9.565325] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 9.596478] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 9.606149] mmcblk0: p1 p2 <4>[ 9.680026] imx_usb 30b10000.usb: No over current polarity defined <4>[ 9.696162] imx_usb 30b20000.usb: No over current polarity defined <4>[ 9.725909] pwm-backlight backlight: supply power not found, using dummy regulator <3>[ 9.761438] fec 30bf0000.ethernet eth0: Unable to connect to phy <3>[ 9.785895] IP-Config: Failed to open eth0 <3>[ 9.790302] IP-Config: No network devices available <4>[ 9.802631] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 9.813317] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <4>[ 9.822607] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <6>[ 9.903412] Freeing unused kernel memory: 2048K <6>[ 9.909835] Run /init as init process <6>[ 10.044214] mmc1: new ultra high speed SDR104 SDIO card at address 0001 Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 10.572477] udevd[133]: starting version 3.2.9 <5>[ 10.583434] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.592329] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 10.600179] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 10.626012] udevd[133]: specified user 'tss' unknown <27>[ 10.631706] udevd[133]: specified group 'tss' unknown <30>[ 10.651665] udevd[134]: starting eudev-3.2.9 <4>[ 16.123789] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 16.132943] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 16.143569] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 16.152479] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 16.240093] gpio-expander@0 enforce active low on chipselect handle <4>[ 16.684876] imx_usb 30b10000.usb: No over current polarity defined <4>[ 17.125755] imx_usb 30b20000.usb: No over current polarity defined <6>[ 17.383388] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 17.389152] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 17.613223] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 17.734710] hub 1-0:1.0: USB hub found <6>[ 17.813248] hub 1-0:1.0: 1 port detected <4>[ 17.899728] pwm-backlight backlight: supply power not found, using dummy regulator <6>[ 19.312542] CAN device driver interface <6>[ 19.368791] caam 30900000.crypto: Entropy delay = 3200 <6>[ 19.433867] caam 30900000.crypto: Instantiated RNG4 SH0 <6>[ 19.493279] caam 30900000.crypto: Instantiated RNG4 SH1 <6>[ 19.498825] caam 30900000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 19.505876] caam 30900000.crypto: job rings = 3, qi = 0 <4>[ 19.563460] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 20.556954] pwm-backlight backlight: supply power not found, using dummy regulator <4>[ 21.569073] pwm-backlight backlight: supply power not found, using dummy regulator <5>[ 21.877794] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 22.940863] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 22.949688] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 22.958805] cfg80211: failed to load regulatory.db <6>[ 23.413750] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 23.436233] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <4>[ 23.487865] pwm-backlight backlight: supply power not found, using dummy regulator <3>[ 24.533705] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 <6>[ 25.728497] caam algorithms registered in /proc/crypto <6>[ 25.742996] caam 30900000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 25.751530] caam 30900000.crypto: registering rng-caam <4>[ 25.785128] pwm-backlight backlight: supply power not found, using dummy regulator done <4>[ 25.957840] pwm-backlight backlight: supply power not found, using dummy regulator <5>[ 25.967647] random: crng init done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1259747/environment . /lava-1259747/environment / # /lava-1259747/bin/lava-test-runner /lava-1259747/0 /lava-1259747/bin/lava-test-runner /lava-1259747/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1259747/0/tests/0_dmesg + cat uuid + UUID=1259747_1.5.2.4.1<8>[ 32.470655] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 32.641162] <8>[ 32.803972] <8>[ 32.950623] + set +x <8>[ 32.963990] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1259747/environment / # . /lava-1259747/environment /lava-1259747/bin/lava-test-runner /lava-1259747/1 / # /lava-1259747/bin/lava-test-runner /lava-1259747/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1259747/1/tests/1_bootrr + cat uuid + UUID=1259747_1.5.2.4.5<8>[ 38.870366] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1259747/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto usbphynop3 imx-pgc-domain.0 imx-pgc: Failed to get domain's regulator imx-pgc-domain.1 imx-pgc: Failed to get domain's regulator imx-pgc-domain.2 imx-pgc: Failed to get domain's regulator panel 30be0000.ethernet 30730000.lcdif 30360000.anatop:tempmon imx_thermal: failed to register cpufreq cooling device regulator-lcd-3v3 backlight /lava-1259747/1/../bin/lava-test-case <8>[ 40.095865] <6>[ 40.254320] vref-1v8: disabling /lava-1259747/1/../bin/lava-test-case <8>[ 41.252879] /lava-1259747/1/../bin/lava-test-case <8>[ 41.328133] + set +x <8>[ 41.380936] / #