[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.11 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12331987/tftp-deploy-gzf8bu9z/kernel/zImage tftp 0x10000000 12331987/tftp-deploy-gzf8bu9z/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '12331987/tftp-deploy-gzf8bu9z/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 5.4 MiB/s done Bytes transferred = 12546560 (bf7200 hex) => tftp 0x14000000 12331987/tftp-deploy-gzf8bu9z/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12331987/tftp-deploy-gzf8bu9z/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '12331987/tftp-deploy-gzf8bu9z/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###### 5.4 MiB/s done Bytes transferred = 15348149 (ea31b5 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12331987/tftp-deploy-gzf8bu9z/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12331987/tftp-deploy-gzf8bu9z/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '12331987/tftp-deploy-gzf8bu9z/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.5 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12331987/extract-nfsrootfs-wc9u9akx,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12331987/extract-nfsrootfs-wc9u9akx,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbf7200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15348085 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.205-cip41 (KernelCI@build-j55122-arm-gcc-10-multi-v7-defconfig-kselftest-lm9f4) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Dec 20 23:42:20 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12331987/extract-nfsrootfs-wc9u9akx,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 921468K/1048576K available (17408K kernel code, 2714K rwdata, 8140K rodata, 2048K init, 6693K bss, 61572K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 56141 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.023040] Console: colour dummy device 80x30 <4>[ 0.024948] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032954] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037297] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041709] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046344] ... CLASSHASH_SIZE: 4096 <4>[ 0.050931] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055653] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060328] ... CHAINHASH_SIZE: 32768 <4>[ 0.065024] memory used by lock dependency info: 4061 kB <4>[ 0.070704] memory used for stack traces: 2112 kB <4>[ 0.075751] per task-struct memory footprint: 1536 bytes <6>[ 0.081439] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091851] CPU: Testing write buffer coherency: ok <6>[ 0.096991] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102264] pid_max: default: 32768 minimum: 301 <6>[ 0.107460] LSM: Security Framework initializing <6>[ 0.112083] LSM support for eBPF active <6>[ 0.116238] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123684] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.135123] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141635] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.148030] rcu: Hierarchical SRCU implementation. <6>[ 0.159416] EFI services will not be available. <6>[ 0.162475] smp: Bringing up secondary CPUs ... <6>[ 0.169015] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.169031] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180807] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180822] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.192222] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.192238] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.201262] smp: Brought up 1 node, 4 CPUs <6>[ 0.204983] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211520] CPU: All CPU(s) started in SVC mode. <6>[ 0.218769] devtmpfs: initialized <6>[ 0.266494] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.273925] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.281848] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.293534] pinctrl core: initialized pinctrl subsystem <6>[ 0.302555] DMI not present or invalid. <6>[ 0.305999] NET: Registered protocol family 16 <6>[ 0.318268] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.331030] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.331539] cpuidle: using governor menu <6>[ 0.339660] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.989330] vdd1p1: supplied by regulator-dummy <6>[ 1.018708] vdd3p0: supplied by regulator-dummy <6>[ 1.047715] vdd2p5: supplied by regulator-dummy <6>[ 1.076800] vddarm: supplied by regulator-dummy <6>[ 1.106560] vddpu: supplied by regulator-dummy <6>[ 1.134901] vddsoc: supplied by regulator-dummy <6>[ 2.290476] No ATAGs? <6>[ 2.291237] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.298450] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.322130] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.352248] Serial: AMBA PL011 UART driver <6>[ 2.409328] Kprobes globally optimized <6>[ 2.512950] iommu: Default domain type: Translated <6>[ 2.517138] vgaarb: loaded <5>[ 2.522565] SCSI subsystem initialized <6>[ 2.525638] usbcore: registered new interface driver usbfs <6>[ 2.529722] usbcore: registered new interface driver hub <6>[ 2.535288] usbcore: registered new device driver usb <6>[ 2.547085] i2c i2c-0: IMX I2C adapter registered <6>[ 2.555313] i2c i2c-1: IMX I2C adapter registered <6>[ 2.561483] i2c i2c-2: IMX I2C adapter registered <6>[ 2.567759] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.570155] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.579675] PTP clock support registered <6>[ 2.598400] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.354504] NET: Registered protocol family 2 <6>[ 4.357033] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.366966] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.373044] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.381076] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.389958] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.396052] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.402989] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.409741] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.417468] NET: Registered protocol family 1 <6>[ 4.423996] RPC: Registered named UNIX socket transport module. <6>[ 4.427578] RPC: Registered udp transport module. <6>[ 4.432654] RPC: Registered tcp transport module. <6>[ 4.437485] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.444281] NET: Registered protocol family 44 <6>[ 4.448966] PCI: CLS 0 bytes, default 64 <6>[ 4.455337] Trying to unpack rootfs image as initramfs... <6>[ 6.231248] Freeing initrd memory: 14992K <4>[ 6.233806] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.241181] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.256545] Initialise system trusted keyrings <6>[ 6.259380] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.307733] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.314237] NFS: Registering the id_resolver key type <5>[ 6.316890] Key type id_resolver registered <5>[ 6.321538] Key type id_legacy registered <6>[ 6.325921] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.332529] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.340243] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.346484] Key type asymmetric registered <5>[ 6.349166] Asymmetric key parser 'x509' registered <6>[ 6.354438] bounce: pool size: 64 pages <6>[ 6.358385] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.365942] io scheduler mq-deadline registered <6>[ 6.370710] io scheduler kyber registered <4>[ 6.375793] test_firmware: interface ready <6>[ 6.539307] mxs-dma 110000.dma-controller: initialized <4>[ 6.599894] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.607909] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 6.815011] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.837028] SuperH (H)SCI(F) driver initialized <6>[ 6.841747] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 6.852473] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 6.859015] printk: console [ttymxc1] enabled <6>[ 6.859015] printk: console [ttymxc1] enabled <6>[ 6.867744] printk: bootconsole [ec_imx21] disabled <6>[ 6.867744] printk: bootconsole [ec_imx21] disabled <6>[ 6.883860] msm_serial: driver initialized <6>[ 6.889359] STMicroelectronics ASC driver initialized <6>[ 6.900757] STM32 USART driver initialized <6>[ 6.925269] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 6.945708] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.954421] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.962466] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.011523] brd: module loaded <6>[ 7.056408] loop: module loaded <6>[ 7.062690] lkdtm: No crash points registered, enable through debugfs <6>[ 7.083653] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.092028] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.100389] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.108912] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.117135] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.125539] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.133508] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.145075] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.152445] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.161575] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.175661] scsi host0: ahci-imx <6>[ 7.181295] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.240962] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.254272] pps pps0: new PPS source ptp0 <6>[ 7.298099] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.308765] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.314023] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.320484] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.326172] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.352395] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.360271] usbcore: registered new interface driver pegasus <6>[ 7.366398] usbcore: registered new interface driver asix <6>[ 7.372260] usbcore: registered new interface driver ax88179_178a <6>[ 7.378830] usbcore: registered new interface driver cdc_ether <6>[ 7.385138] usbcore: registered new interface driver smsc75xx <6>[ 7.391420] usbcore: registered new interface driver smsc95xx <6>[ 7.397583] usbcore: registered new interface driver net1080 <6>[ 7.403700] usbcore: registered new interface driver cdc_subset <6>[ 7.410084] usbcore: registered new interface driver zaurus <6>[ 7.416162] usbcore: registered new interface driver cdc_ncm <6>[ 7.433969] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.440899] ehci-pci: EHCI PCI platform driver <6>[ 7.445771] ehci-platform: EHCI generic platform driver <6>[ 7.452264] ehci-orion: EHCI orion driver <6>[ 7.457403] SPEAr-ehci: EHCI SPEAr driver <6>[ 7.462534] ehci-st: EHCI STMicroelectronics driver <6>[ 7.468526] ehci-exynos: EHCI Exynos driver <6>[ 7.473765] ehci-atmel: EHCI Atmel driver <6>[ 7.478878] tegra-ehci: Tegra EHCI driver <6>[ 7.483986] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 7.490578] ohci-pci: OHCI PCI platform driver <6>[ 7.495454] ohci-platform: OHCI generic platform driver <6>[ 7.501950] SPEAr-ohci: OHCI SPEAr driver <6>[ 7.507054] ohci-st: OHCI STMicroelectronics driver <6>[ 7.513084] ohci-atmel: OHCI Atmel driver <6>[ 7.520949] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 7.521373] usbcore: registered new interface driver usb-storage <6>[ 7.526975] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 7.539625] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 7.563238] i2c /dev entries driver <6>[ 7.642466] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.649008] sdhci: Copyright(c) Pierre Ossman <6>[ 7.662586] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.675694] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.685223] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 7.690062] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 7.690781] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 7.702877] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 7.712812] usbcore: registered new interface driver usbhid <6>[ 7.718725] usbhid: USB HID core driver <6>[ 7.739585] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 7.739592] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 7.745724] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.762023] IPv4 over IPsec tunneling driver <6>[ 7.771029] NET: Registered protocol family 10 <6>[ 7.780384] mmc2: new high speed SDHC card at address 0001 <6>[ 7.781125] Segment Routing with IPv6 <6>[ 7.792723] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 7.795933] NET: Registered protocol family 17 <6>[ 7.803929] 8021q: 802.1Q VLAN Support v1.8 <5>[ 7.809484] Key type dns_resolver registered <4>[ 7.824556] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 7.827911] ThumbEE CPU extension supported. <4>[ 7.832405] GPT:29296874 != 30560255 <5>[ 7.836950] Registering SWP/SWPB emulation handler <4>[ 7.840821] GPT:Alternate GPT header not at the end of the disk. <4>[ 7.840838] GPT:29296874 != 30560255 <4>[ 7.840852] GPT: Use GNU Parted to correct GPT errors. <5>[ 7.856821] Loading compiled-in X.509 certificates <6>[ 7.861671] mmcblk2: p1 p2 p3 <4>[ 8.022592] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.031234] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.044040] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.077898] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.090756] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.096245] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.128914] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.147982] hub 1-0:1.0: USB hub found <6>[ 8.152594] hub 1-0:1.0: 1 port detected <6>[ 8.167655] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.198506] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.206904] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.219582] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.247637] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.256188] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.268843] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.285941] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.312785] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.321441] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.334152] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.355764] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 8.448675] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 8.657108] hub 1-1:1.0: USB hub found <6>[ 8.661969] hub 1-1:1.0: 3 ports detected <4>[ 8.691418] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.699902] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.712685] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 10.480314] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 10.489236] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 10.518491] Sending DHCP requests ., OK <6>[ 10.563059] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.11 <6>[ 10.571451] IP-Config: Complete: <6>[ 10.574977] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.201.11, mask=255.255.255.0, gw=192.168.201.1 <6>[ 10.585741] host=imx6q-sabrelite-lava-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 10.593926] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 10.593946] nameserver0=192.168.201.1 <6>[ 10.653035] Freeing unused kernel memory: 2048K <6>[ 10.710502] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 <6>[ 14.188959] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 14.213757] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.222378] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.238779] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 14.258249] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 14.297447] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.312236] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.327102] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.354809] CAN device driver interface <4>[ 14.362760] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.373447] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.377547] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.388608] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.389040] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.423015] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.433118] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.444893] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.453918] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.483987] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.512247] caam 2100000.crypto: Entropy delay = 3200 <4>[ 14.533188] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.543283] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.578392] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 14.639148] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 14.644602] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 14.651562] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 14.679746] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.698670] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.719815] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 14.720683] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <4>[ 14.729329] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 14.731963] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 14.739140] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 14.740639] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 14.763684] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 14.772913] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 14.800209] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 14.809685] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 14.816110] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 14.826226] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <6>[ 14.874144] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.883105] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.891859] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.900622] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.942729] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.000414] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.009255] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.028106] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.036932] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.045751] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.054482] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.596145] caam algorithms registered in /proc/crypto <6>[ 15.606188] caam 2100000.crypto: registering rng-caam <5>[ 15.735880] random: crng init done <4>[ 15.746923] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.776704] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.785318] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.802675] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.811399] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.820232] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.828906] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:07:40:03 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.11 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-0 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 17.845589] systemd[1]: System time before build time, advancing clock. <30>[ 18.087962] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 18.129773] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 18.195645] systemd[1]: Set hostname to . <30>[ 19.823535] systemd[1]: Queued start job for default target Graphical Interface. <30>[ 19.837907] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 19.893579] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 19.942954] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 19.993662] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 20.043462] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 20.092694] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 20.141045] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 20.154187] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 20.199985] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 20.239471] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 20.280207] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 20.318934] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 20.362705] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 20.468093] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 20.481225] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 20.521897] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 20.575118] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 20.640024] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 20.683351] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 20.732489] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 20.742067] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 20.763853] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 20.810832] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 20.859666] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 20.934854] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 20.988491] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 21.037624] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 21.109819] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <6>[ 21.120128] fuse: init (API version 7.32) <30>[ 21.142215] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 21.202976] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 21.257310] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 21.310080] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 21.366430] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 21.411520] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 21.467034] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 21.550934] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 21.561451] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 21.613733] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 21.623330] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 21.673758] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 21.683460] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 21.733300] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 21.780123] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Remount Root and Kernel File Systems. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 22.119627] systemd-journald[281]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Reached target Hardware activated USB gadget. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.205-cip41 #1 SMP Wed Dec 20 23:42:20 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12331987/extract-nfsrootfs-wc9u9akx' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12331987/extract-nfsrootfs-wc9u9akx' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12331987/environment . /lava-12331987/environment / # /lava-12331987/bin/lava-test-runner /lava-12331987/0 /lava-12331987/bin/lava-test-runner /lava-12331987/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12331987/0/tests/0_timesync-off ++ cat uuid + UUID=12331987_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-lib + TESTRUN_ID=1_kselftest-lib + cd /lava-12331987/0/tests/1_kselftest-lib ++ cat uuid + UUID=12331987_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c lib -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.201-cip41-540-g3640150b3b169/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2023-12-21 00:11:32-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.201-cip41-540-g3640150b3b169/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1411064 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 47.81K 183KB/s kselftest.tar.xz 15%[==> ] 218.91K 415KB/s kselftest.tar.xz 61%[===========> ] 843.92K 1020KB/s kselftest.tar.xz 100%[===================>] 1.34M 1.40MB/s in 1.0s 2023-12-21 00:11:33 (1.40 MB/s) - 'kselftest.tar.xz' saved [1411064/1411064] skiplist: ======================================== ======================================== lib:printf.sh lib:bitmap.sh lib:prime_numbers.sh lib:strscpy.sh ============== Tests to run =============== lib:printf.sh lib:bitmap.sh lib:prime_numbers.sh lib:strscpy.sh ===========End Tests to run =============== shardfile-lib pass <12>[ 53.838987] kselftest: Running tests in lib TAP version 13 1..4 # selftests: lib: printf.sh <6>[ 54.339603] test_printf: loaded. <6>[ 54.350697] test_printf: all 384 tests passed <6>[ 54.399513] test_printf: unloaded. # printf: ok ok 1 selftests: lib: printf.sh # selftests: lib: bitmap.sh <6>[ 54.801314] test_bitmap: loaded. <3>[ 54.805508] test_bitmap: parselist: 14: input is '0-2047:128/256' OK, Time: 3333 <6>[ 54.825927] test_bitmap: all 1679 tests passed <6>[ 54.865368] test_bitmap: unloaded. # bitmap: ok ok 2 selftests: lib: bitmap.sh # selftests: lib: prime_numbers.sh <6>[ 55.809781] prime numbers: selftest(65536) passed, last prime was 65521 # prime numbers: ok ok 3 selftests: lib: prime_numbers.sh # selftests: lib: strscpy.sh <6>[ 56.241191] test_strscpy: loaded. <6>[ 56.244808] test_strscpy: all 32 tests passed <6>[ 56.292799] test_strscpy: unloaded. # strscpy*: ok ok 4 selftests: lib: strscpy.sh lib_printf_sh pass lib_bitmap_sh pass lib_prime_numbers_sh pass lib_strscpy_sh pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #