[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no =>setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.11 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12521945/tftp-deploy-0w84k5r0/kernel/zImage tftp 0x10000000 12521945/tftp-deploy-0w84k5r0/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '12521945/tftp-deploy-0w84k5r0/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 4.9 MiB/s done Bytes transferred = 12546560 (bf7200 hex) => tftp 0x14000000 12521945/tftp-deploy-0w84k5r0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12521945/tftp-deploy-0w84k5r0/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '12521945/tftp-deploy-0w84k5r0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 4.4 MiB/s done Bytes transferred = 19268508 (126039c hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12521945/tftp-deploy-0w84k5r0/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12521945/tftp-deploy-0w84k5r0/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '12521945/tftp-deploy-0w84k5r0/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.9 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbf7200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19268444 Bytes = 18.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.207-cip41 (KernelCI@build-j76188-arm-gcc-10-multi-v7-defconfig-kselftest-8xbbs) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Jan 13 05:56:42 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917640K/1048576K available (17408K kernel code, 2714K rwdata, 8140K rodata, 2048K init, 6693K bss, 65400K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 56142 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022961] Console: colour dummy device 80x30 <4>[ 0.024862] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032875] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037218] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041630] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046265] ... CLASSHASH_SIZE: 4096 <4>[ 0.050852] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055573] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060249] ... CHAINHASH_SIZE: 32768 <4>[ 0.064945] memory used by lock dependency info: 4061 kB <4>[ 0.070626] memory used for stack traces: 2112 kB <4>[ 0.075671] per task-struct memory footprint: 1536 bytes <6>[ 0.081357] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091771] CPU: Testing write buffer coherency: ok <6>[ 0.096911] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102185] pid_max: default: 32768 minimum: 301 <6>[ 0.107380] LSM: Security Framework initializing <6>[ 0.112001] LSM support for eBPF active <6>[ 0.116157] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123604] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.135051] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141550] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147959] rcu: Hierarchical SRCU implementation. <6>[ 0.159380] EFI services will not be available. <6>[ 0.162436] smp: Bringing up secondary CPUs ... <6>[ 0.168984] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.168998] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180782] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180795] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.192213] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.192228] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.201249] smp: Brought up 1 node, 4 CPUs <6>[ 0.204973] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211507] CPU: All CPU(s) started in SVC mode. <6>[ 0.218763] devtmpfs: initialized <6>[ 0.267719] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.275211] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.283072] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.294782] pinctrl core: initialized pinctrl subsystem <6>[ 0.303824] DMI not present or invalid. <6>[ 0.307271] NET: Registered protocol family 16 <6>[ 0.319566] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.332450] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.332949] cpuidle: using governor menu <6>[ 0.341007] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.987489] vdd1p1: supplied by regulator-dummy <6>[ 1.016762] vdd3p0: supplied by regulator-dummy <6>[ 1.045620] vdd2p5: supplied by regulator-dummy <6>[ 1.074527] vddarm: supplied by regulator-dummy <6>[ 1.104151] vddpu: supplied by regulator-dummy <6>[ 1.132415] vddsoc: supplied by regulator-dummy <6>[ 2.282275] No ATAGs? <6>[ 2.283080] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.290309] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.313244] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.342875] Serial: AMBA PL011 UART driver <6>[ 2.400534] Kprobes globally optimized <6>[ 2.504327] iommu: Default domain type: Translated <6>[ 2.508844] vgaarb: loaded <5>[ 2.513843] SCSI subsystem initialized <6>[ 2.517350] usbcore: registered new interface driver usbfs <6>[ 2.521017] usbcore: registered new interface driver hub <6>[ 2.526564] usbcore: registered new device driver usb <6>[ 2.538361] i2c i2c-0: IMX I2C adapter registered <6>[ 2.546707] i2c i2c-1: IMX I2C adapter registered <6>[ 2.552848] i2c i2c-2: IMX I2C adapter registered <6>[ 2.559125] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.561520] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.571020] PTP clock support registered <6>[ 2.591202] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.359053] NET: Registered protocol family 2 <6>[ 4.361640] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.371578] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.377593] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.385698] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.394394] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.400669] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.407781] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.414354] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.422131] NET: Registered protocol family 1 <6>[ 4.428528] RPC: Registered named UNIX socket transport module. <6>[ 4.432260] RPC: Registered udp transport module. <6>[ 4.437136] RPC: Registered tcp transport module. <6>[ 4.442147] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.448816] NET: Registered protocol family 44 <6>[ 4.453562] PCI: CLS 0 bytes, default 64 <6>[ 4.459985] Trying to unpack rootfs image as initramfs... <6>[ 6.863336] Freeing initrd memory: 18820K <4>[ 6.865692] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.873206] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.888643] Initialise system trusted keyrings <6>[ 6.891751] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.940970] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.947553] NFS: Registering the id_resolver key type <5>[ 6.950186] Key type id_resolver registered <5>[ 6.954569] Key type id_legacy registered <6>[ 6.959275] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.965820] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.973564] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.979816] Key type asymmetric registered <5>[ 6.982483] Asymmetric key parser 'x509' registered <6>[ 6.987755] bounce: pool size: 64 pages <6>[ 6.991702] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.999259] io scheduler mq-deadline registered <6>[ 7.004027] io scheduler kyber registered <4>[ 7.009115] test_firmware: interface ready <6>[ 7.170532] mxs-dma 110000.dma-controller: initialized <4>[ 7.230375] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.238468] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 7.447476] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.469360] SuperH (H)SCI(F) driver initialized <6>[ 7.474077] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.484804] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.491350] printk: console [ttymxc1] enabled <6>[ 7.491350] printk: console [ttymxc1] enabled <6>[ 7.500073] printk: bootconsole [ec_imx21] disabled <6>[ 7.500073] printk: bootconsole [ec_imx21] disabled <6>[ 7.516207] msm_serial: driver initialized <6>[ 7.521654] STMicroelectronics ASC driver initialized <6>[ 7.532968] STM32 USART driver initialized <6>[ 7.556991] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.577089] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.585680] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.593633] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.642788] brd: module loaded <6>[ 7.687774] loop: module loaded <6>[ 7.694200] lkdtm: No crash points registered, enable through debugfs <6>[ 7.714988] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.723337] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.731695] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.740169] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.748425] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.756843] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.764809] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.776372] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.783739] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.792873] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.806984] scsi host0: ahci-imx <6>[ 7.812671] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.871869] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.885178] pps pps0: new PPS source ptp0 <6>[ 7.945092] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.955545] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.960803] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.967271] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.973004] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.998877] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 8.006748] usbcore: registered new interface driver pegasus <6>[ 8.012925] usbcore: registered new interface driver asix <6>[ 8.018741] usbcore: registered new interface driver ax88179_178a <6>[ 8.025295] usbcore: registered new interface driver cdc_ether <6>[ 8.031665] usbcore: registered new interface driver smsc75xx <6>[ 8.037888] usbcore: registered new interface driver smsc95xx <6>[ 8.044096] usbcore: registered new interface driver net1080 <6>[ 8.050169] usbcore: registered new interface driver cdc_subset <6>[ 8.056549] usbcore: registered new interface driver zaurus <6>[ 8.062698] usbcore: registered new interface driver cdc_ncm <6>[ 8.080305] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 8.087274] ehci-pci: EHCI PCI platform driver <6>[ 8.092207] ehci-platform: EHCI generic platform driver <6>[ 8.098649] ehci-orion: EHCI orion driver <6>[ 8.103800] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.108862] ehci-st: EHCI STMicroelectronics driver <6>[ 8.114859] ehci-exynos: EHCI Exynos driver <6>[ 8.120082] ehci-atmel: EHCI Atmel driver <6>[ 8.125184] tegra-ehci: Tegra EHCI driver <6>[ 8.130271] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.136843] ohci-pci: OHCI PCI platform driver <6>[ 8.141758] ohci-platform: OHCI generic platform driver <6>[ 8.148133] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.153262] ohci-st: OHCI STMicroelectronics driver <6>[ 8.159205] ohci-atmel: OHCI Atmel driver <6>[ 8.163667] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.167476] usbcore: registered new interface driver usb-storage <6>[ 8.169686] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.182360] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.205404] i2c /dev entries driver <6>[ 8.283466] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.289940] sdhci: Copyright(c) Pierre Ossman <6>[ 8.303430] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.316401] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.333729] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.338218] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.339197] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.351320] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.361084] usbcore: registered new interface driver usbhid <6>[ 8.367021] usbhid: USB HID core driver <6>[ 8.382908] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.384530] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.394721] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.405428] IPv4 over IPsec tunneling driver <6>[ 8.414595] NET: Registered protocol family 10 <6>[ 8.424790] Segment Routing with IPv6 <6>[ 8.434452] NET: Registered protocol family 17 <6>[ 8.440795] 8021q: 802.1Q VLAN Support v1.8 <5>[ 8.446316] Key type dns_resolver registered <6>[ 8.464661] ThumbEE CPU extension supported. <5>[ 8.469270] Registering SWP/SWPB emulation handler <5>[ 8.478226] Loading compiled-in X.509 certificates <4>[ 8.635081] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.643628] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.651493] mmc2: new high speed SDHC card at address 0001 <4>[ 8.656382] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.660483] mmcblk2: mmc2:0001 SD 14.6 GiB <4>[ 8.692842] imx_usb 2184200.usb: No over current polarity defined <4>[ 8.706022] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 8.706055] ci_hdrc ci_hdrc.1: EHCI Host Controller <4>[ 8.713939] GPT:29296874 != 30560255 <6>[ 8.719326] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 8.722940] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.736572] GPT:29296874 != 30560255 <4>[ 8.740431] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.745966] mmcblk2: p1 p2 p3 <6>[ 8.771752] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.790869] hub 1-0:1.0: USB hub found <6>[ 8.795491] hub 1-0:1.0: 1 port detected <6>[ 8.810616] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.840272] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.848934] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.861575] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.889502] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.898053] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.910647] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.929581] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.956565] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.965231] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.977925] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.999304] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 9.181493] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.389836] hub 1-1:1.0: USB hub found <6>[ 9.395864] hub 1-1:1.0: 3 ports detected <4>[ 9.425754] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.434432] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.448716] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.123128] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 11.141383] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 11.171269] Sending DHCP requests ., OK <6>[ 11.215931] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.11 <6>[ 11.224516] IP-Config: Complete: <6>[ 11.228080] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.201.11, mask=255.255.255.0, gw=192.168.201.1 <6>[ 11.238957] host=imx6q-sabrelite-lava-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 11.247213] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 11.247253] nameserver0=192.168.201.1 <6>[ 11.311715] Freeing unused kernel memory: 2048K <6>[ 11.317790] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 11.707765] udevd[130]: starting version 3.2.9 <5>[ 11.715781] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.723705] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 11.730589] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 11.750024] udevd[130]: specified user 'tss' unknown <27>[ 11.755627] udevd[130]: specified group 'tss' unknown <30>[ 11.769057] udevd[131]: starting eudev-3.2.9 <6>[ 13.083680] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 13.099663] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 13.138701] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 13.181701] panel-simple panel-lcd: Specify missing connector_type <4>[ 13.194709] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 13.245813] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 13.254422] panel-simple panel-lcd: Specify missing connector_type <4>[ 13.387882] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 13.410729] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 13.419895] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 13.428937] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 13.491699] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 13.504328] CAN device driver interface <4>[ 13.539379] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 13.590369] panel-simple panel-lcd: Specify missing connector_type <4>[ 13.647639] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 13.808480] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 13.818250] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 13.831475] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 13.838315] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 13.848116] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 13.854704] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 13.861197] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 13.879211] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <6>[ 13.966557] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 13.975452] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 13.984278] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 13.992991] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.036837] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 14.048418] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 14.057650] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 14.066433] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 14.097642] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.106273] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.192000] caam 2100000.crypto: Entropy delay = 3200 <6>[ 14.258142] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 14.318903] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 14.324422] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 14.331403] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 14.345191] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.385987] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.394894] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.403689] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.412415] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.437628] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 14.450878] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.460172] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.474392] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.484049] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 14.527964] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.536850] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.545778] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.554533] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.603155] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.611831] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.625472] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.691880] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.700636] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.709578] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.718355] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.210782] caam algorithms registered in /proc/crypto <6>[ 15.222722] caam 2100000.crypto: registering rng-caam <5>[ 15.353197] random: crng init done <5>[ 15.356942] random: 1 urandom warning(s) missed due to ratelimiting <4>[ 15.363378] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.372299] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.386463] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.420538] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.429271] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.438104] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.446796] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.461314] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.469814] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.484490] panel-simple panel-lvds0: supply power not found, using dummy regulator done <6>[ 15.521040] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.530033] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.538847] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) Saving random seed: <6>[ 15.547659] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12521945/environment . /lava-12521945/environment / # /lava-12521945/bin/lava-test-runner /lava-12521945/0 /lava-12521945/bin/lava-test-runner /lava-12521945/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12521945/0/tests/0_dmesg + cat uuid + UUID=12521945_1.5.2.4.1<8>[ 16.664079] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.788976] <8>[ 16.904552] <8>[ 17.017923] + set +x <8>[ 17.029935] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12521945/environment / # . /lava-12521945/environment/lava-12521945/bin/lava-test-runner /lava-12521945/1 / # /lava-12521945/bin/lava-test-runner /lava-12521945/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12521945/1/tests/1_bootrr + cat uuid + UUID=12521945_1.5.2.4.5<8>[ 17.674720] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12521945/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd panel-lvds0 backlight-lcd backlight-lvds 120000.hdmi /lava-12521945/1/../bin/lava-test-case <8>[ 18.879770] /lava-12521945/1/../bin/lava-test-case <8>[ 19.002251] /lava-12521945/1/../bin/lava-test-case <8>[ 19.069096] + set +x <8>[ 19.115455] / #