Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.4 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1075358/tftp-deploy-nx65x76r/kernel/zImage tftp 0x82000000 1075358/tftp-deploy-nx65x76r/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1075358/tftp-deploy-nx65x76r/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 5.2 MiB/s done Bytes transferred = 9716224 (944200 hex) => tftp 0x83000000 1075358/tftp-deploy-nx65x76r/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1075358/tftp-deploy-nx65x76r/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1075358/tftp-deploy-nx65x76r/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.2 MiB/s done Bytes transferred = 16085720 (f572d8 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1075358/tftp-deploy-nx65x76r/dtb/am335x-boneblack.dtb tftp 0x88000000 1075358/tftp-deploy-nx65x76r/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.4 Filename '1075358/tftp-deploy-nx65x76r/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62861 (f58d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-01-13 6:13:43 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16085656 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801258c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.207-cip41 (KernelCI@build-j76127-arm-gcc-10-multi-v7-defconfig-wd5rd) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Jan 13 05:44:04 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 410832K/522240K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 45872K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008336] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019077] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033185] Console: colour dummy device 80x30 <3>[ 0.038048] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045094] This ensures that you still see kernel messages. Please <3>[ 0.051814] update your kernel commandline. <6>[ 0.056423] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096040] CPU: Testing write buffer coherency: ok <6>[ 0.101406] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106866] pid_max: default: 32768 minimum: 301 <6>[ 0.112049] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.119860] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.129179] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135517] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.144710] rcu: Hierarchical SRCU implementation. <6>[ 0.154630] EFI services will not be available. <6>[ 0.159803] smp: Bringing up secondary CPUs ... <6>[ 0.164734] smp: Brought up 1 node, 1 CPU <6>[ 0.169123] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.175857] CPU: All CPU(s) started in SVC mode. <6>[ 0.181481] devtmpfs: initialized <6>[ 0.195423] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.203953] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.214381] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.225534] pinctrl core: initialized pinctrl subsystem <6>[ 0.233873] DMI not present or invalid. <6>[ 0.238855] NET: Registered protocol family 16 <6>[ 0.246332] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.273221] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.281393] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.281591] cpuidle: using governor menu <6>[ 1.330153] No ATAGs? <6>[ 1.332778] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.347184] Serial: AMBA PL011 UART driver <6>[ 1.385205] iommu: Default domain type: Translated <6>[ 1.391050] vgaarb: loaded <5>[ 1.395072] SCSI subsystem initialized <6>[ 1.399976] usbcore: registered new interface driver usbfs <6>[ 1.405934] usbcore: registered new interface driver hub <6>[ 1.411790] usbcore: registered new device driver usb <6>[ 1.419041] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.424477] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.434168] PTP clock support registered <6>[ 1.442453] clocksource: Switched to clocksource dmtimer <6>[ 2.450956] NET: Registered protocol family 2 <6>[ 2.456103] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.464584] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.473508] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.481773] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.489448] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.496373] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.503393] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.510963] NET: Registered protocol family 1 <6>[ 2.516586] RPC: Registered named UNIX socket transport module. <6>[ 2.523028] RPC: Registered udp transport module. <6>[ 2.528131] RPC: Registered tcp transport module. <6>[ 2.533253] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.540151] PCI: CLS 0 bytes, default 64 <6>[ 2.545167] Trying to unpack rootfs image as initramfs... <6>[ 3.625753] Freeing initrd memory: 15712K <6>[ 3.631111] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.641469] Initialise system trusted keyrings <6>[ 3.646768] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.659810] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.667156] NFS: Registering the id_resolver key type <5>[ 3.672806] Key type id_resolver registered <5>[ 3.677376] Key type id_legacy registered <6>[ 3.681877] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.689067] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.696997] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.702322] Key type asymmetric registered <5>[ 3.706854] Asymmetric key parser 'x509' registered <6>[ 3.712185] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.720081] io scheduler mq-deadline registered <6>[ 3.725019] io scheduler kyber registered <3>[ 3.877250] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.885942] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 4.004427] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 4.049252] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 4.126619] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.135312] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 4.199982] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.208680] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 4.227140] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.235822] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.304026] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.312538] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.354783] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.457151] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 4.469472] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.478906] printk: console [ttyS0] enabled <6>[ 4.478906] printk: console [ttyS0] enabled <6>[ 4.487959] printk: bootconsole [omap8250] disabled <6>[ 4.487959] printk: bootconsole [omap8250] disabled <6>[ 4.501729] SuperH (H)SCI(F) driver initialized <6>[ 4.508785] msm_serial: driver initialized <6>[ 4.513696] STMicroelectronics ASC driver initialized <6>[ 4.521739] STM32 USART driver initialized <6>[ 4.529164] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 4.548569] random: crng init done <6>[ 4.561760] brd: module loaded <6>[ 4.571463] loop: module loaded <6>[ 4.596387] CAN device driver interface <6>[ 4.602360] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 4.610676] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.615994] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.622332] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.628051] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.702489] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.739210] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.749139] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.755846] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.761691] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.770857] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.778783] usbcore: registered new interface driver pegasus <6>[ 4.784824] usbcore: registered new interface driver asix <6>[ 4.790543] usbcore: registered new interface driver ax88179_178a <6>[ 4.796981] usbcore: registered new interface driver cdc_ether <6>[ 4.803178] usbcore: registered new interface driver smsc75xx <6>[ 4.809249] usbcore: registered new interface driver smsc95xx <6>[ 4.815353] usbcore: registered new interface driver net1080 <6>[ 4.821326] usbcore: registered new interface driver cdc_subset <6>[ 4.827583] usbcore: registered new interface driver zaurus <6>[ 4.833522] usbcore: registered new interface driver cdc_ncm <6>[ 4.844998] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.851835] ehci-pci: EHCI PCI platform driver <6>[ 4.856673] ehci-platform: EHCI generic platform driver <6>[ 4.862720] ehci-orion: EHCI orion driver <6>[ 4.867370] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.871940] ehci-st: EHCI STMicroelectronics driver <6>[ 4.877459] ehci-exynos: EHCI Exynos driver <6>[ 4.882206] ehci-atmel: EHCI Atmel driver <6>[ 4.886845] tegra-ehci: Tegra EHCI driver <6>[ 4.891452] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.898018] ohci-pci: OHCI PCI platform driver <6>[ 4.902845] ohci-platform: OHCI generic platform driver <6>[ 4.908793] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.913467] ohci-st: OHCI STMicroelectronics driver <6>[ 4.918923] ohci-atmel: OHCI Atmel driver <6>[ 4.925180] usbcore: registered new interface driver usb-storage <6>[ 4.942133] i2c /dev entries driver <5>[ 4.973976] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.982175] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.988749] sdhci: Copyright(c) Pierre Ossman <6>[ 4.997701] Synopsys Designware Multimedia Card Interface Driver <6>[ 5.007088] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 5.021632] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.081482] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 5.091025] usbcore: registered new interface driver usbhid <6>[ 5.097007] usbhid: USB HID core driver <6>[ 5.110504] NET: Registered protocol family 10 <6>[ 5.116791] Segment Routing with IPv6 <6>[ 5.120824] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 5.127864] NET: Registered protocol family 17 <6>[ 5.132670] can: controller area network core <6>[ 5.137400] NET: Registered protocol family 29 <6>[ 5.142128] can: raw protocol <6>[ 5.145425] can: broadcast manager protocol <6>[ 5.149897] can: netlink gateway - max_hops=1 <5>[ 5.155331] Key type dns_resolver registered <6>[ 5.160032] ThumbEE CPU extension supported. <5>[ 5.164670] Registering SWP/SWPB emulation handler <3>[ 5.170180] omap_voltage_late_init: Voltage driver support not added <6>[ 5.178425] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 5.187309] Loading compiled-in X.509 certificates <6>[ 5.208726] OMAP GPIO hardware version 0.1 <4>[ 5.243057] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 5.256348] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 5.271487] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <4>[ 5.277842] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 5.285215] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 5.293206] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <4>[ 5.303156] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 5.312902] mmc1: new high speed MMC card at address 0001 <6>[ 5.319493] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 5.324731] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.331252] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.337881] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 5.347354] mmcblk1: p1 <4>[ 5.351494] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 5.386313] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 5.425861] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 5.466153] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 5.489721] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 5.498901] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 5.504027] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.591954] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.634493] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.724313] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 8.913350] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 8.922598] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.952605] Sending DHCP requests ., OK <6>[ 8.996714] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.4 <6>[ 9.004869] IP-Config: Complete: <6>[ 9.008411] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.4, mask=255.255.255.0, gw=192.168.11.1 <6>[ 9.018994] host=192.168.11.4, domain=usen.ad.jp, nis-domain=(none) <6>[ 9.026062] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 9.026081] nameserver0=192.168.11.1 <6>[ 9.050130] Freeing unused kernel memory: 2048K <6>[ 9.073409] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.275356] udevd[97]: starting version 3.2.9 <27>[ 9.291285] udevd[97]: specified user 'tss' unknown <27>[ 9.297146] udevd[97]: specified group 'tss' unknown <30>[ 9.314535] udevd[98]: starting eudev-3.2.9 <4>[ 11.017206] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.026375] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 11.243804] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.252924] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 11.441184] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 11.447023] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 11.656326] hub 1-0:1.0: USB hub found <6>[ 11.722501] hub 1-0:1.0: 1 port detected done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1075358/environment . /lava-1075358/environment / # /lava-1075358/bin/lava-test-runner /lava-1075358/0 /lava-1075358/bin/lava-test-runner /lava-1075358/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1075358/0/tests/0_dmesg + cat uuid + UUID=1075358_1.5.2.4.1 + <8>[ 16.557112] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 16.614439] <8>[ 16.665969] <8>[ 16.717813] + set +x <8>[ 16.728610] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1075358/environment / # . /lava-1075358/environment/lava-1075358/bin/lava-test-runner /lava-1075358/1 / # /lava-1075358/bin/lava-test-runner /lava-1075358/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1075358/1/tests/1_bootrr + cat uuid + UUID=1075358_1.5.2.4.5 + <8>[ 17.249782] set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1075358/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto sound /lava-1075358/1/../bin/lava-test-case <8>[ 18.341774] /lava-1075358/1/../bin/lava-test-case <8>[ 18.391359] /lava-1075358/1/../bin/lava-test-case <8>[ 18.421221] /lava-1075358/1/../bin/lava-test-case <8>[ 18.476600] /lava-1075358/1/../bin/lava-test-case <8>[ 18.522940] /lava-1075358/1/../bin/lava-test-case <8>[ 18.559639] /lava-1075358/1/../bin/lava-test-case <8>[ 18.606007] /lava-1075358/1/../bin/lava-test-case <8>[ 18.650836] /lava-1075358/1/../bin/lava-test-case <8>[ 18.688103] /lava-1075358/1/../bin/lava-test-case <8>[ 18.734287] /lava-1075358/1/../bin/lava-test-case <8>[ 19.798969] /lava-1075358/1/../bin/lava-test-case <8>[ 20.860784] /lava-1075358/1/../bin/lava-test-case <8>[ 20.897475] /lava-1075358/1/../bin/lava-test-case <8>[ 20.933528] /lava-1075358/1/../bin/lava-test-case <8>[ 20.970247] /lava-1075358/1/../bin/lava-test-case <8>[ 21.015665] /lava-1075358/1/../bin/lava-test-case <8>[ 21.053251] /lava-1075358/1/../bin/lava-test-case <8>[ 21.099739] /lava-1075358/1/../bin/lava-test-case <8>[ 21.144843] /lava-1075358/1/../bin/lava-test-case <8>[ 21.181478] /lava-1075358/1/../bin/lava-test-case <8>[ 21.227760] /lava-1075358/1/../bin/lava-test-case <8>[ 21.273545] /lava-1075358/1/../bin/lava-test-case <8>[ 21.310990] /lava-1075358/1/../bin/lava-test-case <8>[ 21.357403] /lava-1075358/1/../bin/lava-test-case <8>[ 21.394653] /lava-1075358/1/../bin/lava-test-case <8>[ 21.440169] /lava-1075358/1/../bin/lava-test-case <8>[ 22.500969] /lava-1075358/1/../bin/lava-test-case <8>[ 23.563041] /lava-1075358/1/../bin/lava-test-case <8>[ 23.600396] /lava-1075358/1/../bin/lava-test-case <8>[ 23.647033] /lava-1075358/1/../bin/lava-test-case <8>[ 23.684855] /lava-1075358/1/../bin/lava-test-case <8>[ 23.730236] /lava-1075358/1/../bin/lava-test-case <8>[ 24.790787] /lava-1075358/1/../bin/lava-test-case <8>[ 25.852877] /lava-1075358/1/../bin/lava-test-case <8>[ 25.889678] /lava-1075358/1/../bin/lava-test-case <8>[ 25.936038] /lava-1075358/1/../bin/lava-test-case <8>[ 26.999650] /lava-1075358/1/../bin/lava-test-case <8>[ 28.061086] /lava-1075358/1/../bin/lava-test-case <8>[ 29.121602] /lava-1075358/1/../bin/lava-test-case <8>[ 30.183153] /lava-1075358/1/../bin/lava-test-case <8>[ 31.248604] /lava-1075358/1/../bin/lava-test-case <8>[ 32.311372] /lava-1075358/1/../bin/lava-test-case <8>[ 33.372820] /lava-1075358/1/../bin/lava-test-case <8>[ 34.438429] /lava-1075358/1/../bin/lava-test-case <8>[ 35.500260] /lava-1075358/1/../bin/lava-test-case <8>[ 36.561270] /lava-1075358/1/../bin/lava-test-case <8>[ 37.622731] /lava-1075358/1/../bin/lava-test-case <8>[ 38.688739] /lava-1075358/1/../bin/lava-test-case <8>[ 39.751312] /opt/bootrr/libexec/bootrr/boards/ti,am335x-bone-black: line 84: assert_device-present: not found /lava-1075358/1/../bin/lava-test-case <8>[ 39.790278] /lava-1075358/1/../bin/lava-test-case <8>[ 40.860982] /lava-1075358/1/../bin/lava-test-case <8>[ 41.920759] + set +x <8>[ 41.936410] / #