Trying 192.168.1.205... Connected to ts5. Escape character is '^]'. ser2net port telnet,2000 device serialdev,/dev/ttyUSB-lf-bbb-01,115200n81,local [] (Debian GNU/Linux) U-Boot SPL 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) Trying to boot from MMC2 U-Boot 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 172.16.3.137 (72 ms) => setenv serverip 172.16.3.3 setenv serverip 172.16.3.3 => tftp 0x82000000 1075356/tftp-deploy-d5s5s5is/kernel/zImage tftp 0x82000000 1075356/tftp-deploy-d5s5s5is/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.137 Filename '1075356/tftp-deploy-d5s5s5is/kernel/zImage'. Load address: 0x82000000 Loading: *################################################## 4.4 MiB 5 MiB/s done Bytes transferred = 4611016 (465bc8 hex) => tftp 0x83000000 1075356/tftp-deploy-d5s5s5is/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1075356/tftp-deploy-d5s5s5is/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.137 Filename '1075356/tftp-deploy-d5s5s5is/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################## 10.4 MiB 3.7 MiB/s done Bytes transferred = 10927513 (a6bd99 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1075356/tftp-deploy-d5s5s5is/dtb/am335x-boneblack.dtb tftp 0x88000000 1075356/tftp-deploy-d5s5s5is/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.137 Filename '1075356/tftp-deploy-d5s5s5is/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *################################################## 61.4 KiB 4 MiB/s done Bytes transferred = 62861 (f58d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=172.16.3.3:/var/lib/lava/dispatcher/tmp/1075356/extract-nfsrootfs-7k58hyyn,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=172.16.3.3:/var/lib/lava/dispatcher/tmp/1075356/extract-nfsrootfs-7k58hyyn,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 Kernel image @ 0x82000000 [ 0x000000 - 0x465bc8 ] ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-01-13 6:10:49 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 10927449 Bytes = 10.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801258c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.207-cip41 (KernelCI@build-j76085-arm-gcc-10-omap2plus-defconfig-bgvh2) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Sat Jan 13 05:38:27 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=172.16.3.3:/var/lib/lava/dispatcher/tmp/1075356/extract-nfsrootfs-7k58hyyn,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 475192K/522240K available (9216K kernel code, 1028K rwdata, 2180K rodata, 1024K init, 282K bss, 30664K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008342] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018566] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030206] Console: colour dummy device 80x30 <3>[ 0.035082] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042139] This ensures that you still see kernel messages. Please <3>[ 0.048864] update your kernel commandline. <6>[ 0.053466] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095543] CPU: Testing write buffer coherency: ok <6>[ 0.100917] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106381] pid_max: default: 32768 minimum: 301 <6>[ 0.111541] LSM: Security Framework initializing <6>[ 0.116640] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124452] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134122] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140645] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147839] rcu: Hierarchical SRCU implementation. <6>[ 0.153625] smp: Bringing up secondary CPUs ... <6>[ 0.158560] smp: Brought up 1 node, 1 CPU <6>[ 0.162990] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169719] CPU: All CPU(s) started in SVC mode. <6>[ 0.175452] devtmpfs: initialized <6>[ 0.191107] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199701] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210141] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218639] pinctrl core: initialized pinctrl subsystem <6>[ 0.226287] NET: Registered protocol family 16 <6>[ 0.233902] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260388] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266476] audit: initializing netlink subsys (disabled) <6>[ 0.273550] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273563] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280173] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.286895] cpuidle: using governor menu <5>[ 1.160006] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.284563] No ATAGs? <6>[ 1.287186] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.311650] Kprobes globally optimized <6>[ 1.324758] iommu: Default domain type: Translated <6>[ 1.332132] vgaarb: loaded <5>[ 1.335729] SCSI subsystem initialized <6>[ 1.340935] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.346318] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.356117] PTP clock support registered <6>[ 1.361747] clocksource: Switched to clocksource dmtimer <5>[ 1.999092] VFS: Disk quotas dquot_6.6.0 <6>[ 2.003596] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.020412] NET: Registered protocol family 2 <6>[ 2.025582] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.034241] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.043196] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.051467] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.059150] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.066093] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.073124] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.080725] NET: Registered protocol family 1 <6>[ 2.086525] RPC: Registered named UNIX socket transport module. <6>[ 2.092987] RPC: Registered udp transport module. <6>[ 2.098094] RPC: Registered tcp transport module. <6>[ 2.103220] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.110126] PCI: CLS 0 bytes, default 64 <6>[ 2.115178] Trying to unpack rootfs image as initramfs... <6>[ 2.832642] Freeing initrd memory: 10672K <6>[ 2.838290] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 2.848713] Initialise system trusted keyrings <6>[ 2.854162] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 2.862546] NFS: Registering the id_resolver key type <5>[ 2.868092] Key type id_resolver registered <5>[ 2.872740] Key type id_legacy registered <6>[ 2.877192] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 2.885194] Key type asymmetric registered <5>[ 2.889685] Asymmetric key parser 'x509' registered <6>[ 2.895031] io scheduler mq-deadline registered <6>[ 2.899960] io scheduler kyber registered <3>[ 3.037520] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.046231] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.154552] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.196523] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.268091] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.276797] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.336565] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.345257] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.362810] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.371428] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.434897] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.443437] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.470999] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.485693] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.496605] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.506036] printk: console [ttyS0] enabled <6>[ 3.506036] printk: console [ttyS0] enabled <6>[ 3.515104] printk: bootconsole [omap8250] disabled <6>[ 3.515104] printk: bootconsole [omap8250] disabled <6>[ 3.538925] brd: module loaded <6>[ 3.549614] loop: module loaded <3>[ 3.555246] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.621700] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.650726] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.660659] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.667376] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.673174] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.680670] cpsw 4a100000.ethernet: Detected MACID = 34:03:de:5e:2c:05 <6>[ 3.689713] i2c /dev entries driver <5>[ 3.695387] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 3.703292] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.709772] sdhci: Copyright(c) Pierre Ossman <6>[ 3.715199] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 3.723501] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.733426] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.741920] Initializing XFRM netlink socket <6>[ 3.746694] NET: Registered protocol family 10 <6>[ 3.753219] Segment Routing with IPv6 <6>[ 3.757266] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.764346] NET: Registered protocol family 17 <6>[ 3.769109] NET: Registered protocol family 15 <5>[ 3.774023] Key type dns_resolver registered <6>[ 3.779170] oprofile: using arm/armv7 <6>[ 3.783304] ThumbEE CPU extension supported. <5>[ 3.787884] Registering SWP/SWPB emulation handler <3>[ 3.793413] omap_voltage_late_init: Voltage driver support not added <3>[ 3.800075] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 3.808519] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 3.817206] SmartReflex Class3 initialized <6>[ 3.822032] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 3.830887] Loading compiled-in X.509 certificates <6>[ 3.855972] OMAP GPIO hardware version 0.1 <4>[ 3.892394] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 3.906076] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 3.914854] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 3.921196] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 3.931244] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 3.942666] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 3.951764] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 3.956926] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 3.967326] mmc1: new high speed MMC card at address 0001 <6>[ 3.974271] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 3.979523] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 3.986220] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 3.993764] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.004109] mmcblk1: p1 <6>[ 4.027914] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.037569] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.123451] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 6.202373] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.211721] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.241850] Sending DHCP requests ., OK <6>[ 6.385817] IP-Config: Got DHCP answer from 172.16.3.3, my address is 172.16.3.137 <6>[ 6.393726] IP-Config: Complete: <6>[ 6.397237] device=eth0, hwaddr=34:03:de:5e:2c:05, ipaddr=172.16.3.137, mask=255.255.255.0, gw=172.16.3.3 <6>[ 6.407567] host=172.16.3.137, domain=denx.de, nis-domain=(none) <6>[ 6.414315] bootserver=172.16.3.33, rootserver=172.16.3.3, rootpath= <6>[ 6.414322] nameserver0=172.16.3.3 <6>[ 6.425529] ntpserver0=172.16.3.3 <6>[ 6.432461] Freeing unused kernel memory: 1024K <6>[ 6.442215] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.12-1~deb12u1 <4>[ 7.647693] at24 0-0050: supply vcc not found, using dummy regulator <3>[ 7.764735] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 7.801282] remoteproc remoteproc0: wkup_m3 is available <4>[ 7.812969] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 7.843563] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 7.851187] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 7.861945] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <3>[ 7.883555] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 7.922130] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 7.931133] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 7.943725] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 7.993026] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 7.998448] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <6>[ 8.049817] usbcore: registered new interface driver usbfs <6>[ 8.055784] usbcore: registered new interface driver hub <6>[ 8.061470] usbcore: registered new device driver usb <4>[ 8.100321] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 8.166998] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 8.236148] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 8.280625] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 8.292369] tda998x 0-0070: found TDA19988 <3>[ 8.377464] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 8.469321] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <3>[ 8.548414] davinci-mcasp 48038000.mcasp: IRQ common not found <4>[ 8.682852] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 8.691978] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 8.745395] remoteproc remoteproc0: powering up wkup_m3 <4>[ 8.751101] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 8.761052] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 8.767290] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 8.796944] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 8.804635] random: crng init done <6>[ 8.924004] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 8.936317] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 8.942077] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.002309] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 9.132142] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 9.170210] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 9.176889] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.185518] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.193063] usb usb1: Product: MUSB HDRC host driver <6>[ 9.198313] usb usb1: Manufacturer: Linux 5.10.207-cip41 musb-hcd <6>[ 9.204714] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 9.218385] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 9.228780] PM: Cannot get wkup_m3_ipc handle <6>[ 9.242804] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 9.322443] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 9.331617] omap-aes 53500000.aes: will run requests pump with realtime priority <6>[ 9.498751] hub 1-0:1.0: USB hub found <6>[ 9.541601] hub 1-0:1.0: 1 port detected <3>[ 9.564398] PM: Cannot get wkup_m3_ipc handle <3>[ 9.804936] PM: Cannot get wkup_m3_ipc handle <3>[ 9.835851] PM: Cannot get wkup_m3_ipc handle Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... done. Begin: Waiting up to 180 secs for any network device to become available ... done. IP-Config: eth0 hardware address 34:03:de:5e:2c:05 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 172.16.3.3): address: 172.16.3.137 broadcast: 172.16.3.255 netmask: 255.255.255.0 gateway: 172.16.3.3 dns0 : 172.16.3.3 dns1 : 0.0.0.0 domain : denx.de rootserver: 172.16.3.33 rootpath: filename : this-host-is-not-configured.kpxe done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... mount: No such file or directory mount: invalid option -- done. mount: No such file or directory run-init: opening console: No such file or directory Target filesystem doesn't have requested /sbin/init. run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory run-init: opening console: No such file or directory No init found. Try passing init= bootarg. (initramfs) <3>[ 64.522375] PM: Cannot get wkup_m3_ipc handle <6>[ 64.527271] platform pm33xx: deferred probe pending