[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB OK In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12837730/tftp-deploy-ef5_56x0/kernel/zImage tftp 0x10000000 12837730/tftp-deploy-ef5_56x0/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12837730/tftp-deploy-ef5_56x0/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 14.1 MiB/s done Bytes transferred = 12554752 (bf9200 hex) => tftp 0x14000000 12837730/tftp-deploy-ef5_56x0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12837730/tftp-deploy-ef5_56x0/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12837730/tftp-deploy-ef5_56x0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 14.1 MiB/s done Bytes transferred = 19261417 (125e7e9 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12837730/tftp-deploy-ef5_56x0/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12837730/tftp-deploy-ef5_56x0/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '12837730/tftp-deploy-ef5_56x0/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.1 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbf9200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19261353 Bytes = 18.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.210-cip44 (KernelCI@build-j118011-arm-gcc-10-multi-v7-defconfig-kselftest-4vv2x) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Feb 23 09:52:57 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917648K/1048576K available (17408K kernel code, 2714K rwdata, 8144K rodata, 2048K init, 6693K bss, 65392K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 56146 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022962] Console: colour dummy device 80x30 <4>[ 0.024866] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032876] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037220] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041632] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046266] ... CLASSHASH_SIZE: 4096 <4>[ 0.050853] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055574] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060249] ... CHAINHASH_SIZE: 32768 <4>[ 0.064947] memory used by lock dependency info: 4061 kB <4>[ 0.070627] memory used for stack traces: 2112 kB <4>[ 0.075673] per task-struct memory footprint: 1536 bytes <6>[ 0.081363] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091776] CPU: Testing write buffer coherency: ok <6>[ 0.096912] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102186] pid_max: default: 32768 minimum: 301 <6>[ 0.107379] LSM: Security Framework initializing <6>[ 0.112007] LSM support for eBPF active <6>[ 0.116157] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123605] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.135059] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141545] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147922] rcu: Hierarchical SRCU implementation. <6>[ 0.159276] EFI services will not be available. <6>[ 0.162335] smp: Bringing up secondary CPUs ... <6>[ 0.168825] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.168841] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180597] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180612] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.191990] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.192007] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.201030] smp: Brought up 1 node, 4 CPUs <6>[ 0.204754] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211288] CPU: All CPU(s) started in SVC mode. <6>[ 0.218525] devtmpfs: initialized <6>[ 0.267156] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.274602] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.282513] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.294209] pinctrl core: initialized pinctrl subsystem <6>[ 0.303222] DMI not present or invalid. <6>[ 0.306694] NET: Registered protocol family 16 <6>[ 0.318854] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.331694] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.332194] cpuidle: using governor menu <6>[ 0.340254] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.982803] vdd1p1: supplied by regulator-dummy <6>[ 1.011953] vdd3p0: supplied by regulator-dummy <6>[ 1.040684] vdd2p5: supplied by regulator-dummy <6>[ 1.069481] vddarm: supplied by regulator-dummy <6>[ 1.099064] vddpu: supplied by regulator-dummy <6>[ 1.127167] vddsoc: supplied by regulator-dummy <6>[ 2.270614] No ATAGs? <6>[ 2.271414] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.278651] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.301551] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.331144] Serial: AMBA PL011 UART driver <6>[ 2.388330] Kprobes globally optimized <6>[ 2.492478] iommu: Default domain type: Translated <6>[ 2.496968] vgaarb: loaded <5>[ 2.501973] SCSI subsystem initialized <6>[ 2.505493] usbcore: registered new interface driver usbfs <6>[ 2.509128] usbcore: registered new interface driver hub <6>[ 2.514643] usbcore: registered new device driver usb <6>[ 2.526735] i2c i2c-0: IMX I2C adapter registered <6>[ 2.534839] i2c i2c-1: IMX I2C adapter registered <6>[ 2.541003] i2c i2c-2: IMX I2C adapter registered <6>[ 2.547279] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.549675] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.559171] PTP clock support registered <6>[ 2.579976] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.269508] NET: Registered protocol family 2 <6>[ 4.272101] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.282041] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.288055] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.296163] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.304899] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.311359] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.317959] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.324830] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.332592] NET: Registered protocol family 1 <6>[ 4.338933] RPC: Registered named UNIX socket transport module. <6>[ 4.342776] RPC: Registered udp transport module. <6>[ 4.347600] RPC: Registered tcp transport module. <6>[ 4.352622] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.359277] NET: Registered protocol family 44 <6>[ 4.364036] PCI: CLS 0 bytes, default 64 <6>[ 4.370470] Trying to unpack rootfs image as initramfs... <6>[ 6.771943] Freeing initrd memory: 18812K <4>[ 6.774291] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.781894] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.797260] Initialise system trusted keyrings <6>[ 6.800318] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.849789] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.856310] NFS: Registering the id_resolver key type <5>[ 6.858995] Key type id_resolver registered <5>[ 6.863328] Key type id_legacy registered <6>[ 6.868020] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.874575] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.882341] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.888588] Key type asymmetric registered <5>[ 6.891237] Asymmetric key parser 'x509' registered <6>[ 6.896501] bounce: pool size: 64 pages <6>[ 6.900470] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.908013] io scheduler mq-deadline registered <6>[ 6.912784] io scheduler kyber registered <4>[ 6.917823] test_firmware: interface ready <6>[ 7.078768] mxs-dma 110000.dma-controller: initialized <4>[ 7.138342] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.146429] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 7.353871] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.375821] SuperH (H)SCI(F) driver initialized <6>[ 7.380477] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.391362] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.397810] printk: console [ttymxc1] enabled <6>[ 7.397810] printk: console [ttymxc1] enabled <6>[ 7.406707] printk: bootconsole [ec_imx21] disabled <6>[ 7.406707] printk: bootconsole [ec_imx21] disabled <6>[ 7.423018] msm_serial: driver initialized <6>[ 7.428341] STMicroelectronics ASC driver initialized <6>[ 7.439627] STM32 USART driver initialized <6>[ 7.464666] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.484718] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.493286] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.501169] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.550028] brd: module loaded <6>[ 7.595505] loop: module loaded <6>[ 7.601840] lkdtm: No crash points registered, enable through debugfs <6>[ 7.622673] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.630956] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.639257] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.647781] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.656042] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.664417] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.672495] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.683978] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.691350] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.700486] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.714595] scsi host0: ahci-imx <6>[ 7.720282] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.779350] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.792635] pps pps0: new PPS source ptp0 <6>[ 7.852377] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.862829] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.868087] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.874549] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.880279] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.905997] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.913875] usbcore: registered new interface driver pegasus <6>[ 7.920076] usbcore: registered new interface driver asix <6>[ 7.925896] usbcore: registered new interface driver ax88179_178a <6>[ 7.932450] usbcore: registered new interface driver cdc_ether <6>[ 7.938757] usbcore: registered new interface driver smsc75xx <6>[ 7.945020] usbcore: registered new interface driver smsc95xx <6>[ 7.951253] usbcore: registered new interface driver net1080 <6>[ 7.957332] usbcore: registered new interface driver cdc_subset <6>[ 7.963712] usbcore: registered new interface driver zaurus <6>[ 7.969874] usbcore: registered new interface driver cdc_ncm <6>[ 7.987412] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.994345] ehci-pci: EHCI PCI platform driver <6>[ 7.999219] ehci-platform: EHCI generic platform driver <6>[ 8.005710] ehci-orion: EHCI orion driver <6>[ 8.010886] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.015956] ehci-st: EHCI STMicroelectronics driver <6>[ 8.021934] ehci-exynos: EHCI Exynos driver <6>[ 8.027174] ehci-atmel: EHCI Atmel driver <6>[ 8.032281] tegra-ehci: Tegra EHCI driver <6>[ 8.037374] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.043948] ohci-pci: OHCI PCI platform driver <6>[ 8.048823] ohci-platform: OHCI generic platform driver <6>[ 8.055244] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.060354] ohci-st: OHCI STMicroelectronics driver <6>[ 8.062363] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.066299] ohci-atmel: OHCI Atmel driver <6>[ 8.071563] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.079529] usbcore: registered new interface driver usb-storage <6>[ 8.082141] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.117868] i2c /dev entries driver <6>[ 8.195965] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.202486] sdhci: Copyright(c) Pierre Ossman <6>[ 8.215827] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.228751] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.238228] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.241508] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.243796] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.255987] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.266130] usbcore: registered new interface driver usbhid <6>[ 8.272054] usbhid: USB HID core driver <6>[ 8.290940] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.297989] netem: version 1.3 <6>[ 8.301152] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.301808] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.316767] IPv4 over IPsec tunneling driver <6>[ 8.325876] NET: Registered protocol family 10 <6>[ 8.336059] Segment Routing with IPv6 <6>[ 8.345704] NET: Registered protocol family 17 <6>[ 8.352162] 8021q: 802.1Q VLAN Support v1.8 <5>[ 8.357522] Key type dns_resolver registered <6>[ 8.376160] ThumbEE CPU extension supported. <5>[ 8.380825] Registering SWP/SWPB emulation handler <5>[ 8.389626] Loading compiled-in X.509 certificates <4>[ 8.547851] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.556485] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.564151] mmc2: new high speed SDHC card at address 0001 <4>[ 8.569055] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.573584] mmcblk2: mmc2:0001 SD 14.8 GiB <4>[ 8.605541] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.618514] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.624176] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 8.632136] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 8.639988] GPT:7812499 != 30965759 <4>[ 8.643761] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.650109] GPT:7812499 != 30965759 <4>[ 8.653881] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.659353] mmcblk2: p1 p2 p3 <6>[ 8.689866] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.708289] hub 1-0:1.0: USB hub found <6>[ 8.712900] hub 1-0:1.0: 1 port detected <6>[ 8.727813] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.757843] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.766337] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.778764] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.806370] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.814926] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.827353] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.845790] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.872207] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.880716] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.893173] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.913660] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 9.100216] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.308223] hub 1-1:1.0: USB hub found <6>[ 9.314146] hub 1-1:1.0: 3 ports detected <4>[ 9.343878] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.352500] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.366565] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 12.081709] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 12.110273] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 12.139851] Sending DHCP requests ., OK <6>[ 12.184529] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 <6>[ 12.193047] IP-Config: Complete: <6>[ 12.196611] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 <6>[ 12.207387] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) <6>[ 12.215539] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 12.215556] nameserver0=192.168.201.1 <6>[ 12.271561] Freeing unused kernel memory: 2048K <6>[ 12.280645] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 12.676284] udevd[132]: starting version 3.2.9 <5>[ 12.684616] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.692773] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.699654] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 12.719215] udevd[132]: specified user 'tss' unknown <27>[ 12.725113] udevd[132]: specified group 'tss' unknown <30>[ 12.738167] udevd[133]: starting eudev-3.2.9 <6>[ 14.012328] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 14.028436] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 14.052352] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.060916] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.126533] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 14.172544] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.181143] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.193755] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.202941] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.214796] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.223884] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.286311] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 14.390269] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.420672] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.433657] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.441317] caam 2100000.crypto: Entropy delay = 3200 <6>[ 14.507727] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 14.568489] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 14.573988] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 14.580954] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 14.599393] CAN device driver interface <6>[ 14.651521] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.664309] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.750133] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.756976] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 14.780474] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 14.809959] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 14.816360] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 14.851167] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <6>[ 14.891340] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.900200] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.908905] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.917785] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.038243] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.046850] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.080905] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.121900] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.130618] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 15.139647] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 15.148414] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 15.168568] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.177350] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.186267] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.195057] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.235358] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.255954] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.270102] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.278771] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 15.292655] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.301614] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.311134] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.320224] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.330502] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 15.364476] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.373473] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.426650] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.455861] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.464844] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.473683] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.482412] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.512044] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.520808] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.067193] caam algorithms registered in /proc/crypto <6>[ 16.077190] caam 2100000.crypto: registering rng-caam <4>[ 16.096999] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.121852] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.130599] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.139282] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.148078] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) done <4>[ 16.184645] panel-simple panel-lcd: supply power not found, using dummy regulator Saving random seed: <4>[ 16.193235] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.209757] panel-simple panel-lvds0: supply power not found, using dummy regulator <5>[ 16.224116] random: dd: uninitialized urandom read (32 bytes read) OK <5>[ 16.266285] random: crng init done Starting network: <5>[ 16.270506] random: 1 urandom warning(s) missed due to ratelimiting ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12837730/environment . /lava-12837730/environment / # /lava-12837730/bin/lava-test-runner /lava-12837730/0 /lava-12837730/bin/lava-test-runner /lava-12837730/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12837730/0/tests/0_dmesg + cat uuid + UUID=12837730_1.5.2.4.1<8>[ 17.302946] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.426643] <8>[ 17.535028] <8>[ 17.650485] + set +x <8>[ 17.662329] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12837730/environment / # . /lava-12837730/environment/lava-12837730/bin/lava-test-runner /lava-12837730/1 / # /lava-12837730/bin/lava-test-runner /lava-12837730/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12837730/1/tests/1_bootrr + cat uuid + UUID=12837730_1.5.2.4.5<8>[ 18.314494] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12837730/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto 120000.hdmi backlight-lcd backlight-lvds panel-lcd panel-lvds0 /lava-12837730/1/../bin/lava-test-case <8>[ 19.517622] /lava-12837730/1/../bin/lava-test-case <8>[ 19.635557] /lava-12837730/1/../bin/lava-test-case <8>[ 19.702370] + set +x <8>[ 19.747518] / #