[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12965457/tftp-deploy-sv2ytvp3/kernel/zImage tftp 0x10000000 12965457/tftp-deploy-sv2ytvp3/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12965457/tftp-deploy-sv2ytvp3/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 14.3 MiB/s done Bytes transferred = 12558848 (bfa200 hex) => tftp 0x14000000 12965457/tftp-deploy-sv2ytvp3/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12965457/tftp-deploy-sv2ytvp3/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12965457/tftp-deploy-sv2ytvp3/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### 14.2 MiB/s done Bytes transferred = 15337770 (ea092a hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12965457/tftp-deploy-sv2ytvp3/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12965457/tftp-deploy-sv2ytvp3/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '12965457/tftp-deploy-sv2ytvp3/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.8 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12965457/extract-nfsrootfs-idj3psh3,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12965457/extract-nfsrootfs-idj3psh3,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbfa200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 15337706 Bytes = 14.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.212-cip44 (KernelCI@build-j132469-arm-gcc-10-multi-v7-defconfig-kselftest-l78c2) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 6 21:21:06 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/12965457/extract-nfsrootfs-idj3psh3,tcp,hard console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 921480K/1048576K available (17408K kernel code, 2714K rwdata, 8144K rodata, 2048K init, 6693K bss, 61560K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 56146 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000010] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022886] Console: colour dummy device 80x30 <4>[ 0.024792] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032799] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037144] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041558] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046192] ... CLASSHASH_SIZE: 4096 <4>[ 0.050779] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055499] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060173] ... CHAINHASH_SIZE: 32768 <4>[ 0.064872] memory used by lock dependency info: 4061 kB <4>[ 0.070550] memory used for stack traces: 2112 kB <4>[ 0.075597] per task-struct memory footprint: 1536 bytes <6>[ 0.081287] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091701] CPU: Testing write buffer coherency: ok <6>[ 0.096837] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102111] pid_max: default: 32768 minimum: 301 <6>[ 0.107301] LSM: Security Framework initializing <6>[ 0.111930] LSM support for eBPF active <6>[ 0.116083] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123532] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.134929] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141421] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147786] rcu: Hierarchical SRCU implementation. <6>[ 0.159115] EFI services will not be available. <6>[ 0.162172] smp: Bringing up secondary CPUs ... <6>[ 0.168682] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.168697] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180455] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180469] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.191886] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.191901] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.200926] smp: Brought up 1 node, 4 CPUs <6>[ 0.204647] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211181] CPU: All CPU(s) started in SVC mode. <6>[ 0.218388] devtmpfs: initialized <6>[ 0.265784] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.273198] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.281139] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.292830] pinctrl core: initialized pinctrl subsystem <6>[ 0.301742] DMI not present or invalid. <6>[ 0.305126] NET: Registered protocol family 16 <6>[ 0.317275] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.329916] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.330411] cpuidle: using governor menu <6>[ 0.338522] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.979632] vdd1p1: supplied by regulator-dummy <6>[ 1.008695] vdd3p0: supplied by regulator-dummy <6>[ 1.037348] vdd2p5: supplied by regulator-dummy <6>[ 1.066058] vddarm: supplied by regulator-dummy <6>[ 1.095508] vddpu: supplied by regulator-dummy <6>[ 1.123294] vddsoc: supplied by regulator-dummy <6>[ 2.264040] No ATAGs? <6>[ 2.264845] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.272074] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.294930] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.324469] Serial: AMBA PL011 UART driver <6>[ 2.380665] Kprobes globally optimized <6>[ 2.483514] iommu: Default domain type: Translated <6>[ 2.487998] vgaarb: loaded <5>[ 2.492952] SCSI subsystem initialized <6>[ 2.496445] usbcore: registered new interface driver usbfs <6>[ 2.500102] usbcore: registered new interface driver hub <6>[ 2.505676] usbcore: registered new device driver usb <6>[ 2.517580] i2c i2c-0: IMX I2C adapter registered <6>[ 2.525698] i2c i2c-1: IMX I2C adapter registered <6>[ 2.531781] i2c i2c-2: IMX I2C adapter registered <6>[ 2.538030] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.540427] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.549923] PTP clock support registered <6>[ 2.568817] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.339486] NET: Registered protocol family 2 <6>[ 4.341936] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.351960] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.357972] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.366096] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.374801] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.381262] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.387876] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.394754] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.402514] NET: Registered protocol family 1 <6>[ 4.409149] RPC: Registered named UNIX socket transport module. <6>[ 4.412573] RPC: Registered udp transport module. <6>[ 4.417521] RPC: Registered tcp transport module. <6>[ 4.422550] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.429247] NET: Registered protocol family 44 <6>[ 4.433903] PCI: CLS 0 bytes, default 64 <6>[ 4.440230] Trying to unpack rootfs image as initramfs... <6>[ 6.204882] Freeing initrd memory: 14980K <4>[ 6.207436] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.215104] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.230234] Initialise system trusted keyrings <6>[ 6.233015] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.280840] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.287266] NFS: Registering the id_resolver key type <5>[ 6.290002] Key type id_resolver registered <5>[ 6.294201] Key type id_legacy registered <6>[ 6.299031] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.305474] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.313279] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.319584] Key type asymmetric registered <5>[ 6.322109] Asymmetric key parser 'x509' registered <6>[ 6.327470] bounce: pool size: 64 pages <6>[ 6.331445] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.339017] io scheduler mq-deadline registered <6>[ 6.343695] io scheduler kyber registered <4>[ 6.348804] test_firmware: interface ready <6>[ 6.508664] mxs-dma 110000.dma-controller: initialized <4>[ 6.568314] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.576400] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 6.782208] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.803983] SuperH (H)SCI(F) driver initialized <6>[ 6.808565] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 6.819476] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 6.825911] printk: console [ttymxc1] enabled <6>[ 6.825911] printk: console [ttymxc1] enabled <6>[ 6.834818] printk: bootconsole [ec_imx21] disabled <6>[ 6.834818] printk: bootconsole [ec_imx21] disabled <6>[ 6.850855] msm_serial: driver initialized <6>[ 6.856171] STMicroelectronics ASC driver initialized <6>[ 6.867435] STM32 USART driver initialized <6>[ 6.892106] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 6.912141] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.920795] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.928649] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.977118] brd: module loaded <6>[ 7.021745] loop: module loaded <6>[ 7.027868] lkdtm: No crash points registered, enable through debugfs <6>[ 7.048574] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.056913] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.065266] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.073788] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.082046] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.090422] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.098392] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.109893] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.117176] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.126402] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.140495] scsi host0: ahci-imx <6>[ 7.146035] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.204797] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.218105] pps pps0: new PPS source ptp0 <6>[ 7.261569] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.272035] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.277293] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.283757] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.289510] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.315178] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.323048] usbcore: registered new interface driver pegasus <6>[ 7.329252] usbcore: registered new interface driver asix <6>[ 7.335070] usbcore: registered new interface driver ax88179_178a <6>[ 7.341623] usbcore: registered new interface driver cdc_ether <6>[ 7.347937] usbcore: registered new interface driver smsc75xx <6>[ 7.354195] usbcore: registered new interface driver smsc95xx <6>[ 7.360415] usbcore: registered new interface driver net1080 <6>[ 7.366490] usbcore: registered new interface driver cdc_subset <6>[ 7.372863] usbcore: registered new interface driver zaurus <6>[ 7.378998] usbcore: registered new interface driver cdc_ncm <6>[ 7.396510] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.403444] ehci-pci: EHCI PCI platform driver <6>[ 7.408321] ehci-platform: EHCI generic platform driver <6>[ 7.414808] ehci-orion: EHCI orion driver <6>[ 7.419960] SPEAr-ehci: EHCI SPEAr driver <6>[ 7.425017] ehci-st: EHCI STMicroelectronics driver <6>[ 7.431001] ehci-exynos: EHCI Exynos driver <6>[ 7.436233] ehci-atmel: EHCI Atmel driver <6>[ 7.441329] tegra-ehci: Tegra EHCI driver <6>[ 7.446413] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 7.452990] ohci-pci: OHCI PCI platform driver <6>[ 7.457862] ohci-platform: OHCI generic platform driver <6>[ 7.464268] SPEAr-ohci: OHCI SPEAr driver <6>[ 7.469386] ohci-st: OHCI STMicroelectronics driver <6>[ 7.475309] ohci-atmel: OHCI Atmel driver <6>[ 7.483535] usbcore: registered new interface driver usb-storage <6>[ 7.491451] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 7.497478] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 7.504128] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 7.519425] i2c /dev entries driver <6>[ 7.597066] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.603584] sdhci: Copyright(c) Pierre Ossman <6>[ 7.616876] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.629903] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.639428] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 7.639435] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 7.650170] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 7.656714] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 7.666428] usbcore: registered new interface driver usbhid <6>[ 7.672340] usbhid: USB HID core driver <6>[ 7.677904] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 7.690495] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 7.698477] netem: version 1.3 <6>[ 7.702228] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.710364] IPv4 over IPsec tunneling driver <6>[ 7.719309] NET: Registered protocol family 10 <6>[ 7.729374] Segment Routing with IPv6 <6>[ 7.738926] NET: Registered protocol family 17 <6>[ 7.745241] 8021q: 802.1Q VLAN Support v1.8 <5>[ 7.750727] Key type dns_resolver registered <6>[ 7.768870] ThumbEE CPU extension supported. <5>[ 7.773467] Registering SWP/SWPB emulation handler <5>[ 7.782331] Loading compiled-in X.509 certificates <4>[ 7.936962] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.945511] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.953237] mmc2: new high speed SDHC card at address aaaa <4>[ 7.958178] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.962275] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <4>[ 7.994648] imx_usb 2184200.usb: No over current polarity defined <4>[ 8.004482] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 8.007651] ci_hdrc ci_hdrc.1: EHCI Host Controller <4>[ 8.012346] GPT:29296874 != 31116287 <6>[ 8.017765] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <4>[ 8.021388] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.021401] GPT:29296874 != 31116287 <4>[ 8.021411] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.021476] mmcblk2: p1 p2 p3 <6>[ 8.079326] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.094042] hub 1-0:1.0: USB hub found <6>[ 8.098553] hub 1-0:1.0: 1 port detected <6>[ 8.115326] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.145014] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.153486] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.165988] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.193857] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.202314] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.214749] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.232850] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.259159] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.267558] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.280124] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.300894] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 8.499071] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 8.707245] hub 1-1:1.0: USB hub found <6>[ 8.712191] hub 1-1:1.0: 3 ports detected <4>[ 8.739246] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.747656] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.760334] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 11.440655] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 11.458957] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 11.490002] Sending DHCP requests ., OK <6>[ 11.533424] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 <6>[ 11.541968] IP-Config: Complete: <6>[ 11.545530] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 <6>[ 11.556368] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) <6>[ 11.564618] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 11.564658] nameserver0=192.168.201.1 <6>[ 11.628729] Freeing unused kernel memory: 2048K <6>[ 11.639987] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u4 <6>[ 15.166208] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 15.199411] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.209100] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.220310] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 15.234039] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.245736] CAN device driver interface <4>[ 15.269342] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.277830] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.290906] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 15.325634] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.334239] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.353521] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.362581] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.370749] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 15.377587] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 15.385629] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 15.392280] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 15.398673] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 15.408479] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1 <4>[ 15.419839] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.428012] caam 2100000.crypto: Entropy delay = 3200 <4>[ 15.451152] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.459706] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.475053] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.494304] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 15.555077] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.560609] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 15.567523] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 15.616441] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.623215] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.625300] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 15.632918] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.658464] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.663218] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 15.667507] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.675853] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 15.684290] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.701331] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.711915] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.716491] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 15.741677] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.750269] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.763513] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.773986] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 15.823627] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.832512] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.848393] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.880837] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.889793] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.898666] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.907619] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.971954] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.982562] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.997535] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.510760] caam algorithms registered in /proc/crypto <6>[ 16.520741] caam 2100000.crypto: registering rng-caam <6>[ 16.538668] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.547381] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.556096] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.564801] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.593200] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.601790] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.614567] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Ru<6>[ 16.642451] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) nning /scripts/nfs-top ... done. <6>[ 16.652764] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) Begin: Running /scripts/nfs-prem<6>[ 16.664395] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) ount ... Waiting up to 60 secs fo<6>[ 16.675360] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) r any ethernet to become available Device /sys/class/net/eth0 found done. <5>[ 16.709583] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:13 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.33 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-3 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 18.694845] systemd[1]: System time before build time, advancing clock. <30>[ 18.961621] systemd[1]: systemd 247.3-7+deb11u4 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 18.990401] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 19.045632] systemd[1]: Set hostname to . <30>[ 20.591329] systemd[1]: Queued start job for default target Graphical Interface. <30>[ 20.606416] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 20.624228] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 20.661313] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 20.703148] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 20.752850] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 20.802131] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 20.850531] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 20.864546] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 20.911233] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 20.949298] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 20.989754] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 21.029879] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 21.073932] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 21.174090] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 21.188674] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 21.235153] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 21.285268] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 21.340836] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 21.383811] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 21.433880] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 21.444425] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 21.462480] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 21.510270] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 21.569379] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 21.631917] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 21.678041] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 21.737835] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 21.802080] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <6>[ 21.807018] fuse: init (API version 7.32) <30>[ 21.830203] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 21.901674] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 21.948191] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 21.998615] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 22.068063] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 22.111006] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 22.156538] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 22.240000] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 22.249964] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. <30>[ 22.304146] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 22.314171] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module drm. <30>[ 22.354548] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 22.364466] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Module fuse. <30>[ 22.413954] systemd[1]: Finished Load Kernel Modules. [ OK ] Finished Load Kernel Modules. <30>[ 22.460371] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Remount Root and Kernel File Systems. Mounting FUSE Control File System... Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... <46>[ 22.781380] systemd-journald[273]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted FUSE Control File System. [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Flush Journal to Persistent Storage. Starting Create Volatile Files and Directories... [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target System Initialization. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Permit User Sessions... [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Permit User Sessions. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.212-cip44 #1 SMP Wed Mar 6 21:21:06 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12965457/extract-nfsrootfs-idj3psh3' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/12965457/extract-nfsrootfs-idj3psh3' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-12965457/environment . /lava-12965457/environment / # /lava-12965457/bin/lava-test-runner /lava-12965457/0 /lava-12965457/bin/lava-test-runner /lava-12965457/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-12965457/0/tests/0_timesync-off ++ cat uuid + UUID=12965457_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-livepatch + TESTRUN_ID=1_kselftest-livepatch + cd /lava-12965457/0/tests/1_kselftest-livepatch ++ cat uuid + UUID=12965457_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c livepatch -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.209-cip44-594-gb47da48f3bae7/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2024-03-06 21:37:04-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.209-cip44-594-gb47da48f3bae7/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1409000 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 50.15K 193KB/s kselftest.tar.xz 7%[> ] 109.54K 208KB/s kselftest.tar.xz 20%[===> ] 283.47K 355KB/s kselftest.tar.xz 29%[====> ] 406.98K 387KB/s kselftest.tar.xz 37%[======> ] 510.21K 388KB/s kselftest.tar.xz 44%[=======> ] 619.09K 392KB/s kselftest.tar.xz 53%[=========> ] 732.21K 397KB/s kselftest.tar.xz 61%[===========> ] 846.75K 402KB/s kselftest.tar.xz 69%[============> ] 961.29K 405KB/s kselftest.tar.xz 78%[==============> ] 1.05M 409KB/s kselftest.tar.xz 86%[================> ] 1.17M 411KB/s kselftest.tar.xz 95%[==================> ] 1.28M 414KB/s eta 0s kselftest.tar.xz 100%[===================>] 1.34M 417KB/s in 3.3s 2024-03-06 21:37:07 (417 KB/s) - 'kselftest.tar.xz' saved [1409000/1409000] skiplist: ======================================== ======================================== livepatch:test-livepatch.sh livepatch:test-callbacks.sh livepatch:test-shadow-vars.sh livepatch:test-state.sh livepatch:test-ftrace.sh ============== Tests to run =============== livepatch:test-livepatch.sh livepatch:test-callbacks.sh livepatch:test-shadow-vars.sh livepatch:test-state.sh livepatch:test-ftrace.sh ===========End Tests to run =============== shardfile-livepatch pass <12>[ 54.175627] kselftest: Running tests in livepatch TAP version 13 1..5 # selftests: livepatch: test-livepatch.sh <12>[ 54.801102] livepatch: kernel.ftrace_enabled = 1 # TE<12>[ 54.897249] ===== TEST: basic function patching ===== ST: basic function patching ... <12>[ 54.967125] SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 1 selftests: livepatch: test-livepatch.sh # SKIP # selftests: livepatch: test-callbacks.sh <12>[ 55.456568] livepatch: kernel.ftrace_enabled = 1 # T<12>[ 55.537262] ===== TEST: target module before livepatch ===== EST: target module before livepatch ... <12>[ 55.591854] SKIP: unable to load module test_klp_callbacks_mod, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_callbacks_mod, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 2 selftests: livepatch: test-callbacks.sh # SKIP # selftests: livepatch: test-shadow-vars.sh <12>[ 56.069257] livepatch: kernel.ftrace_enabled = 1 # TE<12>[ 56.148561] ===== TEST: basic shadow variable API ===== ST: basic shadow variable API ... <12>[ 56.201886] SKIP: unable to load module test_klp_shadow_vars, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_shadow_vars, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 3 selftests: livepatch: test-shadow-vars.sh # SKIP # selftests: livepatch: test-state.sh <12>[ 56.682531] livepatch: kernel.ftrace_enabled = 1 # <12>[ 56.764540] ===== TEST: system state modification ===== TEST: system state modification ... <12>[ 56.820565] SKIP: unable to load module test_klp_state, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_state, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 4 selftests: livepatch: test-state.sh # SKIP # selftests: livepatch: test-ftrace.sh <12>[ 57.295105] livepatch: kernel.ftrace_enabled = 1 # TEST: <12>[ 57.378711] ===== TEST: livepatch interaction with ftrace_enabled sysctl ===== livepatch interaction with ftrace_enabled sysctl ... <12>[ 57.436829] livepatch: kernel.ftrace_enabled = 0 <12>[ 57.442759] % modprobe test_klp_livepatch <12>[ 57.505526] modprobe: FATAL: Module test_klp_livepatch not found in directory /lib/modules/5.10.212-cip44 <12>[ 57.564786] livepatch: kernel.ftrace_enabled = 1 <12>[ 57.626535] SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root SKIP: unable to load module test_klp_livepatch, verify CONFIG_TEST_LIVEPATCH=m and run self-tests as root ok 5 selftests: livepatch: test-ftrace.sh # SKIP Traceback (most recent call last): File "/lava-12965457/0/tests/1_kselftest-livepatch/automated/linux/kselftest/./parse-output.py", line 4, in from tap import parser ModuleNotFoundError: No module named 'tap' + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #