[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 12965345/tftp-deploy-ocuatezy/kernel/zImage tftp 0x10000000 12965345/tftp-deploy-ocuatezy/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '12965345/tftp-deploy-ocuatezy/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 14.3 MiB/s done Bytes transferred = 9716224 (944200 hex) => tftp 0x14000000 12965345/tftp-deploy-ocuatezy/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 12965345/tftp-deploy-ocuatezy/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '12965345/tftp-deploy-ocuatezy/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 14.3 MiB/s done Bytes transferred = 16080999 (f56067 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 12965345/tftp-deploy-ocuatezy/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 12965345/tftp-deploy-ocuatezy/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '12965345/tftp-deploy-ocuatezy/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.1 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x944200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16080935 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.212-cip44 (KernelCI@build-j132347-arm-gcc-10-multi-v7-defconfig-42tsm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 6 21:02:04 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932648K/1048576K available (14336K kernel code, 2239K rwdata, 5364K rodata, 2048K init, 424K bss, 50392K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022184] Console: colour dummy device 80x30 <6>[ 0.024074] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034483] CPU: Testing write buffer coherency: ok <6>[ 0.039616] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044914] pid_max: default: 32768 minimum: 301 <6>[ 0.049944] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057377] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066257] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071999] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079719] rcu: Hierarchical SRCU implementation. <6>[ 0.086715] EFI services will not be available. <6>[ 0.088949] smp: Bringing up secondary CPUs ... <6>[ 0.094237] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094245] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105583] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105590] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116795] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116803] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127232] smp: Brought up 1 node, 4 CPUs <6>[ 0.131458] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137910] CPU: All CPU(s) started in SVC mode. <6>[ 0.143327] devtmpfs: initialized <6>[ 0.153513] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158840] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168720] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179722] pinctrl core: initialized pinctrl subsystem <6>[ 0.184222] DMI not present or invalid. <6>[ 0.187320] NET: Registered protocol family 16 <6>[ 0.194574] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.201256] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.201454] cpuidle: using governor menu <6>[ 0.209489] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.394140] vdd1p1: supplied by regulator-dummy <6>[ 0.403462] vdd3p0: supplied by regulator-dummy <6>[ 0.412722] vdd2p5: supplied by regulator-dummy <6>[ 0.422028] vddarm: supplied by regulator-dummy <6>[ 0.431477] vddpu: supplied by regulator-dummy <6>[ 0.440547] vddsoc: supplied by regulator-dummy <6>[ 0.779950] No ATAGs? <6>[ 0.780139] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.787912] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.798159] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.808536] Serial: AMBA PL011 UART driver <6>[ 0.812706] printk: console [ramoops-1] enabled <6>[ 0.815035] pstore: Registered ramoops as persistent store backend <6>[ 0.821290] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.859192] iommu: Default domain type: Translated <6>[ 0.861912] vgaarb: loaded <5>[ 0.865312] SCSI subsystem initialized <6>[ 0.869112] usbcore: registered new interface driver usbfs <6>[ 0.874223] usbcore: registered new interface driver hub <6>[ 0.879809] usbcore: registered new device driver usb <6>[ 0.886659] i2c i2c-0: IMX I2C adapter registered <6>[ 0.891342] i2c i2c-1: IMX I2C adapter registered <6>[ 0.895864] i2c i2c-2: IMX I2C adapter registered <6>[ 0.901298] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.905158] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.914594] PTP clock support registered <6>[ 0.922293] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.032587] NET: Registered protocol family 2 <6>[ 2.034785] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.043426] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.050660] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.058741] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.066180] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.072870] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.079548] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.087025] NET: Registered protocol family 1 <6>[ 2.092045] RPC: Registered named UNIX socket transport module. <6>[ 2.097644] RPC: Registered udp transport module. <6>[ 2.102595] RPC: Registered tcp transport module. <6>[ 2.107528] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.114247] PCI: CLS 0 bytes, default 64 <6>[ 2.118878] Trying to unpack rootfs image as initramfs... <6>[ 3.473045] Freeing initrd memory: 15708K <4>[ 3.474954] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.482221] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.492145] Initialise system trusted keyrings <6>[ 3.495214] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.507419] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.511384] NFS: Registering the id_resolver key type <5>[ 3.516078] Key type id_resolver registered <5>[ 3.520409] Key type id_legacy registered <6>[ 3.524787] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.531634] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.539335] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.544396] Key type asymmetric registered <5>[ 3.548251] Asymmetric key parser 'x509' registered <6>[ 3.553449] bounce: pool size: 64 pages <6>[ 3.557503] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.565148] io scheduler mq-deadline registered <6>[ 3.569912] io scheduler kyber registered <6>[ 3.614444] mxs-dma 110000.dma-controller: initialized <4>[ 3.621775] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.629589] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.680038] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.688235] SuperH (H)SCI(F) driver initialized <6>[ 3.691185] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.700072] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.707987] printk: console [ttymxc1] enabled <6>[ 3.707987] printk: console [ttymxc1] enabled <6>[ 3.717156] printk: bootconsole [ec_imx21] disabled <6>[ 3.717156] printk: bootconsole [ec_imx21] disabled <6>[ 3.729012] msm_serial: driver initialized <6>[ 3.734903] STMicroelectronics ASC driver initialized <6>[ 3.742203] STM32 USART driver initialized <4>[ 3.757196] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.765131] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.771940] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.788734] brd: module loaded <6>[ 3.799525] loop: module loaded <6>[ 3.806977] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.815199] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.823501] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.831950] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.839989] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.847740] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.855326] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.865929] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.873215] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.882288] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.893102] scsi host0: ahci-imx <6>[ 3.896974] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.917873] CAN device driver interface <6>[ 3.923437] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.932921] pps pps0: new PPS source ptp0 <6>[ 3.969678] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.977340] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.982598] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.988855] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.994539] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.006763] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.014497] usbcore: registered new interface driver pegasus <6>[ 4.020465] usbcore: registered new interface driver asix <6>[ 4.026188] usbcore: registered new interface driver ax88179_178a <6>[ 4.032604] usbcore: registered new interface driver cdc_ether <6>[ 4.038748] usbcore: registered new interface driver smsc75xx <6>[ 4.044833] usbcore: registered new interface driver smsc95xx <6>[ 4.050879] usbcore: registered new interface driver net1080 <6>[ 4.056858] usbcore: registered new interface driver cdc_subset <6>[ 4.063094] usbcore: registered new interface driver zaurus <6>[ 4.069002] usbcore: registered new interface driver cdc_ncm <6>[ 4.078617] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.085435] ehci-pci: EHCI PCI platform driver <6>[ 4.090185] ehci-platform: EHCI generic platform driver <6>[ 4.096029] ehci-orion: EHCI orion driver <6>[ 4.100536] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.105031] ehci-st: EHCI STMicroelectronics driver <6>[ 4.110372] ehci-exynos: EHCI Exynos driver <6>[ 4.115031] ehci-atmel: EHCI Atmel driver <6>[ 4.119496] tegra-ehci: Tegra EHCI driver <6>[ 4.124013] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.130476] ohci-pci: OHCI PCI platform driver <6>[ 4.135256] ohci-platform: OHCI generic platform driver <6>[ 4.141028] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.145537] ohci-st: OHCI STMicroelectronics driver <6>[ 4.150888] ohci-atmel: OHCI Atmel driver <6>[ 4.156459] usbcore: registered new interface driver usb-storage <6>[ 4.171281] i2c /dev entries driver <6>[ 4.196023] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.202495] sdhci: Copyright(c) Pierre Ossman <6>[ 4.209976] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.218338] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.225567] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.229923] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.230855] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.241630] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.249026] usbcore: registered new interface driver usbhid <6>[ 4.252315] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.254894] usbhid: USB HID core driver <6>[ 4.260573] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.271192] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.271455] NET: Registered protocol family 10 <6>[ 4.272922] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.291462] Segment Routing with IPv6 <6>[ 4.295492] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.302262] NET: Registered protocol family 17 <6>[ 4.303941] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.306986] can: controller area network core <6>[ 4.310358] mmc2: new high speed SDHC card at address aaaa <6>[ 4.311212] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <4>[ 4.319410] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 4.324638] NET: Registered protocol family 29 <4>[ 4.329259] GPT:29296874 != 31116287 <6>[ 4.336937] can: raw protocol <4>[ 4.341642] GPT:Alternate GPT header not at the end of the disk. <6>[ 4.345501] can: broadcast manager protocol <4>[ 4.348724] GPT:29296874 != 31116287 <6>[ 4.355014] can: netlink gateway - max_hops=1 <4>[ 4.359450] GPT: Use GNU Parted to correct GPT errors. <5>[ 4.363815] Key type dns_resolver registered <6>[ 4.367971] mmcblk2: p1 p2 p3 <6>[ 4.379850] ThumbEE CPU extension supported. <5>[ 4.385833] Registering SWP/SWPB emulation handler <5>[ 4.391136] Loading compiled-in X.509 certificates <6>[ 4.401203] pstore: Using crash dump compression: deflate <4>[ 4.428672] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.436618] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.444576] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.463537] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.474097] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.479303] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.512393] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.519524] hub 1-0:1.0: USB hub found <6>[ 4.523719] hub 1-0:1.0: 1 port detected <6>[ 4.532427] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.549262] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.557182] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.565106] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.577190] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.585095] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.592978] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.603065] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.615211] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.623126] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.631013] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.645180] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.852331] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 5.053909] hub 1-1:1.0: USB hub found <6>[ 5.058130] hub 1-1:1.0: 3 ports detected <4>[ 5.068705] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.076681] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.084979] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.762803] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.782388] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.812338] Sending DHCP requests ., OK <6>[ 7.856527] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 7.864862] IP-Config: Complete: <6>[ 7.868382] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.879108] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 7.887215] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.887220] nameserver0=192.168.201.1 <6>[ 7.904549] Freeing unused kernel memory: 2048K <6>[ 7.943315] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.074127] udevd[132]: starting version 3.2.9 <5>[ 8.079862] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.087033] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.094423] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.108263] udevd[132]: specified user 'tss' unknown <27>[ 8.113814] udevd[132]: specified group 'tss' unknown <30>[ 8.121338] udevd[133]: starting eudev-3.2.9 <6>[ 8.496269] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.509091] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.517188] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.535514] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.544550] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.564559] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.592425] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.597064] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.601039] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.608859] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.616752] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.629626] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <4>[ 8.630018] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.648143] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.656797] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 8.663816] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.665399] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.673276] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.708334] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.758876] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.766900] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.780748] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.798682] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.805837] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.812691] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <4>[ 8.821080] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.834492] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.840852] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.847293] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.854375] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.862999] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.871529] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.880127] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.888663] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.918930] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.925700] caam 2100000.crypto: Entropy delay = 3200 <4>[ 8.926903] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.966629] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.992798] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 9.031170] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.039732] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.048322] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.053554] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 9.056851] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.062184] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 9.077546] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 9.089570] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.097521] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.105884] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.119037] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.127647] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.136206] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.144755] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.278925] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 9.285669] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 9.286944] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.301141] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.308287] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 9.317164] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.325847] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.334454] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.343098] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.375833] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.383849] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.393237] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.414197] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.422903] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.431461] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.440060] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.589950] caam algorithms registered in /proc/crypto <6>[ 9.596825] caam 2100000.crypto: registering rng-caam <4>[ 9.605963] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.613920] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.622104] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.636086] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.644645] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.653185] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.661684] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 9.682207] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.690180] panel-simple panel-lcd: Specify missing connector_type done <4>[ 9.698995] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: <6>[ 9.713924] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <5>[ 9.717591] random: dd: uninitialized urandom read (32 bytes read) <6>[ 9.722475] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) OK <6>[ 9.737442] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) Starting network: <6>[ 9.746304] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) ip: RTNETLINK answers: File exists FAIL <5>[ 9.784579] random: crng init done <5>[ 9.788261] random: 1 urandom warning(s) missed due to ratelimiting Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-12965345/environment . /lava-12965345/environment / # /lava-12965345/bin/lava-test-runner /lava-12965345/0 /lava-12965345/bin/lava-test-runner /lava-12965345/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-12965345/0/tests/0_dmesg + cat uuid + UUID=12965345_1.5.2<8>[ 10.425364] .4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.472085] <8>[ 10.513506] <8>[ 10.554777] + set<8>[ 10.564735] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-12965345/environment / # . /lava-12965345/environment/lava-12965345/bin/lava-test-runner /lava-12965345/1 / # /lava-12965345/bin/lava-test-runner /lava-12965345/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-12965345/1/tests/1_bootrr <8>[ 11.071758] + cat uuid + UUID=12965345_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-12965345/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds panel-lcd panel-lvds0 backlight-lcd 120000.hdmi /lava-12965345/1/../bin/lava-test-case <8>[ 12.140830] /lava-12965345/1/../bin/lava-test-case <8>[ 12.181152] /lava-12965345/1/../bin/lava-test-case <8>[ 12.206510] + set<8>[ 12.225446] +x / #