[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 13682949/tftp-deploy-th2c3wio/kernel/zImage tftp 0x10000000 13682949/tftp-deploy-th2c3wio/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '13682949/tftp-deploy-th2c3wio/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ### 14.2 MiB/s done Bytes transferred = 12440064 (bdd200 hex) => tftp 0x14000000 13682949/tftp-deploy-th2c3wio/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 13682949/tftp-deploy-th2c3wio/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '13682949/tftp-deploy-th2c3wio/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 14.4 MiB/s done Bytes transferred = 19449592 (128c6f8 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 13682949/tftp-deploy-th2c3wio/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 13682949/tftp-deploy-th2c3wio/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '13682949/tftp-deploy-th2c3wio/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 13.6 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbdd200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19449528 Bytes = 18.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.216-cip46 (KernelCI@build-j188855-arm-gcc-10-multi-v7-defconfig-kselftest-dvvxm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue May 7 20:24:49 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917468K/1048576K available (17408K kernel code, 2711K rwdata, 8124K rodata, 2048K init, 6692K bss, 65572K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 55538 entries in 163 pages <6>[ 0.000000] ftrace: allocated 163 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000008] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022931] Console: colour dummy device 80x30 <4>[ 0.024835] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032846] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037190] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041602] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046236] ... CLASSHASH_SIZE: 4096 <4>[ 0.050823] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055544] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060220] ... CHAINHASH_SIZE: 32768 <4>[ 0.064916] memory used by lock dependency info: 4061 kB <4>[ 0.070597] memory used for stack traces: 2112 kB <4>[ 0.075643] per task-struct memory footprint: 1536 bytes <6>[ 0.081329] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091747] CPU: Testing write buffer coherency: ok <6>[ 0.096883] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102156] pid_max: default: 32768 minimum: 301 <6>[ 0.107356] LSM: Security Framework initializing <6>[ 0.111979] LSM support for eBPF active <6>[ 0.116133] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123575] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.135035] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141559] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147920] rcu: Hierarchical SRCU implementation. <6>[ 0.159244] EFI services will not be available. <6>[ 0.162299] smp: Bringing up secondary CPUs ... <6>[ 0.168818] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.168833] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180594] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180610] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.192025] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.192039] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.201075] smp: Brought up 1 node, 4 CPUs <6>[ 0.204785] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211321] CPU: All CPU(s) started in SVC mode. <6>[ 0.218554] devtmpfs: initialized <6>[ 0.266897] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.274342] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.282251] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.293950] pinctrl core: initialized pinctrl subsystem <6>[ 0.302965] DMI not present or invalid. <6>[ 0.306422] NET: Registered protocol family 16 <6>[ 0.318541] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.331253] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.331745] cpuidle: using governor menu <6>[ 0.339852] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.991098] vdd1p1: supplied by regulator-dummy <6>[ 1.020516] vdd3p0: supplied by regulator-dummy <6>[ 1.049589] vdd2p5: supplied by regulator-dummy <6>[ 1.078727] vddarm: supplied by regulator-dummy <6>[ 1.108660] vddpu: supplied by regulator-dummy <6>[ 1.137153] vddsoc: supplied by regulator-dummy <6>[ 2.295399] No ATAGs? <6>[ 2.296210] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.303375] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.326702] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.356662] Serial: AMBA PL011 UART driver <6>[ 2.413382] Kprobes globally optimized <6>[ 2.517146] iommu: Default domain type: Translated <6>[ 2.521606] vgaarb: loaded <5>[ 2.526738] SCSI subsystem initialized <6>[ 2.530178] usbcore: registered new interface driver usbfs <6>[ 2.533893] usbcore: registered new interface driver hub <6>[ 2.539460] usbcore: registered new device driver usb <6>[ 2.551319] i2c i2c-0: IMX I2C adapter registered <6>[ 2.559584] i2c i2c-1: IMX I2C adapter registered <6>[ 2.565726] i2c i2c-2: IMX I2C adapter registered <6>[ 2.571970] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.574365] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.583876] PTP clock support registered <6>[ 2.604262] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.367843] NET: Registered protocol family 2 <6>[ 4.370362] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.380388] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.386463] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.394501] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.403154] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.409723] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.416379] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.423108] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.430937] NET: Registered protocol family 1 <6>[ 4.437372] RPC: Registered named UNIX socket transport module. <6>[ 4.440998] RPC: Registered udp transport module. <6>[ 4.446072] RPC: Registered tcp transport module. <6>[ 4.450909] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.457672] NET: Registered protocol family 44 <6>[ 4.462332] PCI: CLS 0 bytes, default 64 <6>[ 4.469102] Trying to unpack rootfs image as initramfs... <6>[ 6.867772] Freeing initrd memory: 18996K <4>[ 6.870357] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.877739] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.893095] Initialise system trusted keyrings <6>[ 6.896001] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.944073] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.950638] NFS: Registering the id_resolver key type <5>[ 6.953251] Key type id_resolver registered <5>[ 6.957835] Key type id_legacy registered <6>[ 6.962327] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.968900] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.976654] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.982893] Key type asymmetric registered <5>[ 6.985539] Asymmetric key parser 'x509' registered <6>[ 6.990830] bounce: pool size: 64 pages <6>[ 6.994829] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 7.002346] io scheduler mq-deadline registered <6>[ 7.007111] io scheduler kyber registered <4>[ 7.012114] test_firmware: interface ready <6>[ 7.175348] mxs-dma 110000.dma-controller: initialized <4>[ 7.235506] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.243517] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 7.468343] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.490365] SuperH (H)SCI(F) driver initialized <6>[ 7.495065] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.505816] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.512264] printk: console [ttymxc1] enabled <6>[ 7.512264] printk: console [ttymxc1] enabled <6>[ 7.521146] printk: bootconsole [ec_imx21] disabled <6>[ 7.521146] printk: bootconsole [ec_imx21] disabled <6>[ 7.537121] msm_serial: driver initialized <6>[ 7.542445] STMicroelectronics ASC driver initialized <6>[ 7.553851] STM32 USART driver initialized <6>[ 7.578823] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.599138] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.607716] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.615602] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.664130] brd: module loaded <6>[ 7.709385] loop: module loaded <6>[ 7.715634] lkdtm: No crash points registered, enable through debugfs <6>[ 7.736490] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.744771] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.753072] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.761593] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.769852] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.778259] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.786224] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.797797] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.805191] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.814331] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.828423] scsi host0: ahci-imx <6>[ 7.833997] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.893409] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.906750] pps pps0: new PPS source ptp0 <6>[ 7.966344] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.976856] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.982115] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.988585] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.994317] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 8.020327] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 8.028233] usbcore: registered new interface driver pegasus <6>[ 8.034414] usbcore: registered new interface driver asix <6>[ 8.040231] usbcore: registered new interface driver ax88179_178a <6>[ 8.046788] usbcore: registered new interface driver cdc_ether <6>[ 8.053112] usbcore: registered new interface driver smsc75xx <6>[ 8.059418] usbcore: registered new interface driver smsc95xx <6>[ 8.065636] usbcore: registered new interface driver net1080 <6>[ 8.071716] usbcore: registered new interface driver cdc_subset <6>[ 8.078114] usbcore: registered new interface driver zaurus <6>[ 8.084292] usbcore: registered new interface driver cdc_ncm <6>[ 8.102015] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 8.108970] ehci-pci: EHCI PCI platform driver <6>[ 8.113857] ehci-platform: EHCI generic platform driver <6>[ 8.120352] ehci-orion: EHCI orion driver <6>[ 8.125537] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.130614] ehci-st: EHCI STMicroelectronics driver <6>[ 8.136626] ehci-exynos: EHCI Exynos driver <6>[ 8.141858] ehci-atmel: EHCI Atmel driver <6>[ 8.146974] tegra-ehci: Tegra EHCI driver <6>[ 8.152071] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.158648] ohci-pci: OHCI PCI platform driver <6>[ 8.163523] ohci-platform: OHCI generic platform driver <6>[ 8.169958] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.175095] ohci-st: OHCI STMicroelectronics driver <6>[ 8.176979] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.181053] ohci-atmel: OHCI Atmel driver <6>[ 8.186301] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.194382] usbcore: registered new interface driver usb-storage <6>[ 8.196875] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.232873] i2c /dev entries driver <6>[ 8.312056] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.318590] sdhci: Copyright(c) Pierre Ossman <6>[ 8.332083] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.345157] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.354643] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.354649] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.365446] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.372427] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.382300] usbcore: registered new interface driver usbhid <6>[ 8.388254] usbhid: USB HID core driver <6>[ 8.408107] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.408229] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.414824] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.417190] IPv4 over IPsec tunneling driver <6>[ 8.437321] NET: Registered protocol family 10 <6>[ 8.447399] Segment Routing with IPv6 <6>[ 8.456971] NET: Registered protocol family 17 <5>[ 8.463301] Key type dns_resolver registered <6>[ 8.464624] mmc2: new high speed SDHC card at address e624 <6>[ 8.477377] mmcblk2: mmc2:e624 SL16G 14.8 GiB <6>[ 8.488507] ThumbEE CPU extension supported. <5>[ 8.493113] Registering SWP/SWPB emulation handler <4>[ 8.500209] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 8.508283] GPT:29296874 != 31116287 <5>[ 8.509273] Loading compiled-in X.509 certificates <4>[ 8.512180] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.523599] GPT:29296874 != 31116287 <4>[ 8.527572] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.533065] mmcblk2: p1 p2 p3 <4>[ 8.669520] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.678075] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.690542] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.726601] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.741497] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.747075] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.784753] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.803636] hub 1-0:1.0: USB hub found <6>[ 8.808244] hub 1-0:1.0: 1 port detected <6>[ 8.823048] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.853551] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.862043] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.874621] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.902201] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.910753] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.923176] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.940314] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.969290] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.977784] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.990416] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 9.011790] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 9.174729] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.382735] hub 1-1:1.0: USB hub found <6>[ 9.387783] hub 1-1:1.0: 3 ports detected <4>[ 9.416828] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.425267] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.437916] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 12.176090] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 12.194443] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 12.224711] Sending DHCP requests ., OK <6>[ 12.269223] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 12.277697] IP-Config: Complete: <6>[ 12.281262] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 12.292149] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 12.300388] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 12.300426] nameserver0=192.168.201.1 <6>[ 12.313935] clk: Disabling unused clocks <6>[ 12.371652] Freeing unused kernel memory: 2048K <6>[ 12.385059] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 12.781320] udevd[143]: starting version 3.2.9 <5>[ 12.789956] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.797708] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.805053] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 12.824635] udevd[143]: specified user 'tss' unknown <27>[ 12.830196] udevd[143]: specified group 'tss' unknown <30>[ 12.843395] udevd[144]: starting eudev-3.2.9 <6>[ 14.060222] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 14.085373] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.114760] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.127696] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.193380] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 14.258164] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.284751] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.295836] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.297644] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.304977] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.321517] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.333066] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.381693] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.390283] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.435433] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.496474] CAN device driver interface <6>[ 14.606680] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.624645] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.654076] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.661018] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 14.735573] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 14.774384] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 14.780784] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 14.836802] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 1 <6>[ 14.847587] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.856411] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.865213] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.873865] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.936960] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.945530] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.959218] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.975612] caam 2100000.crypto: Entropy delay = 3200 <6>[ 15.041792] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 15.102555] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.108144] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 15.115161] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 15.158606] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.167421] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.176613] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.185565] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.327172] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.336453] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 15.368593] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 15.377870] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.387278] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.398686] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 15.463585] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.537125] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.546136] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.554883] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.563521] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.584821] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.593320] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.207519] caam algorithms registered in /proc/crypto <6>[ 16.224400] caam 2100000.crypto: registering rng-caam <5>[ 16.353001] random: crng init done <5>[ 16.357666] random: 1 urandom warning(s) missed due to ratelimiting <4>[ 16.365780] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.421087] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.429858] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.438639] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.447294] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.469603] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.478199] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.495373] panel-simple panel-lvds0: supply power not found, using dummy regulator done <6>[ 16.526235] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.535082] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) Saving random seed: <6>[ 16.543842] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.554258] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-13682949/environment . /lava-13682949/environment / # /lava-13682949/bin/lava-test-runner /lava-13682949/0 /lava-13682949/bin/lava-test-runner /lava-13682949/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-13682949/0/tests/0_dmesg + cat uuid + UUID=13682949_1.5.2.4.1<8>[ 17.635441] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.760081] <8>[ 17.873834] <8>[ 17.985355] + set +x <8>[ 17.997329] / #