Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.2 (3 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 1130137/tftp-deploy-95034z_p/kernel/zImage tftp 0x82000000 1130137/tftp-deploy-95034z_p/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1130137/tftp-deploy-95034z_p/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.1 MiB/s done Bytes transferred = 4611736 (465e98 hex) => tftp 0x83000000 1130137/tftp-deploy-95034z_p/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1130137/tftp-deploy-95034z_p/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1130137/tftp-deploy-95034z_p/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.2 MiB/s done Bytes transferred = 14175742 (d84dfe hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1130137/tftp-deploy-95034z_p/dtb/am335x-boneblack.dtb tftp 0x88000000 1130137/tftp-deploy-95034z_p/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '1130137/tftp-deploy-95034z_p/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.3 MiB/s done Bytes transferred = 62861 (f58d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-05-09 4:33:07 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14175678 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801258c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.216-cip47 (KernelCI@build-j190925-arm-gcc-10-omap2plus-defconfig-gkznw) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu May 9 04:02:11 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 472024K/522240K available (9216K kernel code, 1027K rwdata, 2180K rodata, 1024K init, 278K bss, 33832K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008342] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018563] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030212] Console: colour dummy device 80x30 <3>[ 0.035081] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042138] This ensures that you still see kernel messages. Please <3>[ 0.048863] update your kernel commandline. <6>[ 0.053469] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095540] CPU: Testing write buffer coherency: ok <6>[ 0.100922] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106387] pid_max: default: 32768 minimum: 301 <6>[ 0.111548] LSM: Security Framework initializing <6>[ 0.116646] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124465] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134131] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140655] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147850] rcu: Hierarchical SRCU implementation. <6>[ 0.153631] smp: Bringing up secondary CPUs ... <6>[ 0.158566] smp: Brought up 1 node, 1 CPU <6>[ 0.162991] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169719] CPU: All CPU(s) started in SVC mode. <6>[ 0.175450] devtmpfs: initialized <6>[ 0.191561] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.200097] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210535] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.219145] pinctrl core: initialized pinctrl subsystem <6>[ 0.226723] NET: Registered protocol family 16 <6>[ 0.234328] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260837] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266925] audit: initializing netlink subsys (disabled) <6>[ 0.274002] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.274016] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280623] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.287357] cpuidle: using governor menu <5>[ 1.155237] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.279026] No ATAGs? <6>[ 1.281651] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.305929] Kprobes globally optimized <6>[ 1.319218] iommu: Default domain type: Translated <6>[ 1.326259] vgaarb: loaded <5>[ 1.329972] SCSI subsystem initialized <6>[ 1.335279] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.340763] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.350487] PTP clock support registered <6>[ 1.356051] clocksource: Switched to clocksource dmtimer <5>[ 1.994521] VFS: Disk quotas dquot_6.6.0 <6>[ 1.999029] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.015852] NET: Registered protocol family 2 <6>[ 2.021034] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.029693] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.038650] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.046946] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.054605] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.061542] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.068571] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.076198] NET: Registered protocol family 1 <6>[ 2.081979] RPC: Registered named UNIX socket transport module. <6>[ 2.088443] RPC: Registered udp transport module. <6>[ 2.093550] RPC: Registered tcp transport module. <6>[ 2.098676] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.105581] PCI: CLS 0 bytes, default 64 <6>[ 2.110627] Trying to unpack rootfs image as initramfs... <6>[ 3.096774] Freeing initrd memory: 13844K <6>[ 3.102434] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.112860] Initialise system trusted keyrings <6>[ 3.118261] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.126544] NFS: Registering the id_resolver key type <5>[ 3.132061] Key type id_resolver registered <5>[ 3.136688] Key type id_legacy registered <6>[ 3.141148] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.149131] Key type asymmetric registered <5>[ 3.153622] Asymmetric key parser 'x509' registered <6>[ 3.158964] io scheduler mq-deadline registered <6>[ 3.163895] io scheduler kyber registered <3>[ 3.300645] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.309343] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.417042] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.458798] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.529935] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.538632] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.598152] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.606835] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.624183] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.632869] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.696174] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.704629] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 3.731800] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 3.746640] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 3.757701] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 3.767112] printk: console [ttyS0] enabled <6>[ 3.767112] printk: console [ttyS0] enabled <6>[ 3.776180] printk: bootconsole [omap8250] disabled <6>[ 3.776180] printk: bootconsole [omap8250] disabled <6>[ 3.800277] brd: module loaded <6>[ 3.811101] loop: module loaded <3>[ 3.816818] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 3.886021] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 3.929273] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 3.939187] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 3.945840] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 3.951654] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 3.959219] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 3.968241] i2c /dev entries driver <5>[ 3.973789] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 3.981750] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.988294] sdhci: Copyright(c) Pierre Ossman <6>[ 3.993659] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.001987] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.011819] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.020279] Initializing XFRM netlink socket <6>[ 4.025079] NET: Registered protocol family 10 <6>[ 4.031504] Segment Routing with IPv6 <6>[ 4.035546] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.042636] NET: Registered protocol family 17 <6>[ 4.047489] NET: Registered protocol family 15 <5>[ 4.052330] Key type dns_resolver registered <6>[ 4.057519] oprofile: using arm/armv7 <6>[ 4.061564] ThumbEE CPU extension supported. <5>[ 4.066200] Registering SWP/SWPB emulation handler <3>[ 4.071684] omap_voltage_late_init: Voltage driver support not added <3>[ 4.078398] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.086814] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.095488] SmartReflex Class3 initialized <6>[ 4.100471] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.109393] Loading compiled-in X.509 certificates <6>[ 4.134518] OMAP GPIO hardware version 0.1 <4>[ 4.166747] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.180390] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.188910] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.195264] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.205293] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.216705] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.225718] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.230964] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.245229] mmc1: new high speed MMC card at address 0001 <6>[ 4.252079] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.257639] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 4.264302] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 4.270922] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 4.280462] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 4.289457] mmcblk1: p1 <6>[ 4.297789] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 4.387564] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 7.566703] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 7.586041] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.616140] Sending DHCP requests ., OK <6>[ 7.660131] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.2 <6>[ 7.668209] IP-Config: Complete: <6>[ 7.671718] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.2, mask=255.255.255.0, gw=192.168.11.1 <6>[ 7.682218] host=192.168.11.2, domain=usen.ad.jp, nis-domain=(none) <6>[ 7.689251] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 7.689258] nameserver0=192.168.11.1 <6>[ 7.700398] clk: Disabling unused clocks <6>[ 7.707001] Freeing unused kernel memory: 1024K <6>[ 7.726489] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.961040] udevd[100]: starting version 3.2.9 <5>[ 7.968255] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.975465] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.983008] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.000400] udevd[100]: specified user 'tss' unknown <27>[ 8.006626] udevd[100]: specified group 'tss' unknown <30>[ 8.018763] udevd[101]: starting eudev-3.2.9 <6>[ 8.824122] remoteproc remoteproc0: wkup_m3 is available <4>[ 8.887096] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <6>[ 8.964740] usbcore: registered new interface driver usbfs <6>[ 8.970781] usbcore: registered new interface driver hub <6>[ 8.976531] usbcore: registered new device driver usb <4>[ 9.077584] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <6>[ 9.349694] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 9.355350] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.566440] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 9.575034] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 9.582625] usb usb1: Product: MUSB HDRC host driver <6>[ 9.587903] usb usb1: Manufacturer: Linux 5.10.216-cip47 musb-hcd <6>[ 9.594285] usb usb1: SerialNumber: musb-hdrc.1 <4>[ 9.644006] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 9.806394] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 9.814068] at24 2-0054: supply vcc not found, using dummy regulator <3>[ 9.834028] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 9.896427] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 9.901845] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <6>[ 9.922014] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <4>[ 9.970128] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <4>[ 9.996813] at24 2-0055: supply vcc not found, using dummy regulator <6>[ 10.004601] hub 1-0:1.0: USB hub found <6>[ 10.066220] hub 1-0:1.0: 1 port detected <6>[ 10.097790] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <4>[ 10.118999] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 10.180653] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 10.283525] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.329037] tda998x 0-0070: found TDA19988 <3>[ 10.399788] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.785548] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <6>[ 10.803598] remoteproc remoteproc0: powering up wkup_m3 <4>[ 10.935360] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 10.945272] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 10.951543] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <3>[ 11.036746] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 11.491765] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 11.592960] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 11.601087] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 11.608615] random: crng init done <6>[ 11.683915] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 11.701540] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <3>[ 11.944421] PM: Cannot get wkup_m3_ipc handle <6>[ 12.231219] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 12.247036] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <6>[ 12.327122] omap-sham 53100000.sham: will run requests pump with realtime priority <6>[ 12.341149] omap-aes 53500000.aes: will run requests pump with realtime priority <3>[ 12.402204] PM: Cannot get wkup_m3_ipc handle <3>[ 12.419320] PM: Cannot get wkup_m3_ipc handle <3>[ 12.833050] PM: Cannot get wkup_m3_ipc handle <3>[ 12.863663] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1130137/environment . /lava-1130137/environment / # /lava-1130137/bin/lava-test-runner /lava-1130137/0 /lava-1130137/bin/lava-test-runner /lava-1130137/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1130137/0/tests/0_dmesg + cat uuid + UUID=1130137_1.5.2.4.1 + <8>[ 13.773366] set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 13.839642] <8>[ 13.899768] <8>[ 13.959791] + set +x <8>[ 13.971146] / #