[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.0 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected sst25vf016b with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.12 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 14091013/tftp-deploy-j8_h4sww/kernel/zImage tftp 0x10000000 14091013/tftp-deploy-j8_h4sww/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '14091013/tftp-deploy-j8_h4sww/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 3.4 MiB/s done Bytes transferred = 12558848 (bfa200 hex) => tftp 0x14000000 14091013/tftp-deploy-j8_h4sww/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 14091013/tftp-deploy-j8_h4sww/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '14091013/tftp-deploy-j8_h4sww/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 3.1 MiB/s done Bytes transferred = 16103774 (f5b95e hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 14091013/tftp-deploy-j8_h4sww/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 14091013/tftp-deploy-j8_h4sww/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.12 Filename '14091013/tftp-deploy-j8_h4sww/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.4 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/14091013/extract-nfsrootfs-0neqtv6e,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/14091013/extract-nfsrootfs-0neqtv6e,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbfa200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16103710 Bytes = 15.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.216-cip47 (KernelCI@build-j211253-arm-gcc-10-multi-v7-defconfig-kselftest-hpld9) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu May 30 07:51:22 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/14091013/extract-nfsrootfs-0neqtv6e,tcp,hard,v3 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 920728K/1048576K available (17408K kernel code, 2714K rwdata, 8152K rodata, 2048K init, 6693K bss, 62312K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 56169 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 15ns <6>[ 0.000008] sched_clock: 32 bits at 66MHz, resolution 15ns, wraps every 32537631224ns <6>[ 0.008094] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 28958491609 ns <6>[ 0.022508] Console: colour dummy device 80x30 <4>[ 0.024414] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032421] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.036766] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041178] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.045812] ... CLASSHASH_SIZE: 4096 <4>[ 0.050399] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055096] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.059819] ... CHAINHASH_SIZE: 32768 <4>[ 0.064493] memory used by lock dependency info: 4061 kB <4>[ 0.070172] memory used for stack traces: 2112 kB <4>[ 0.075195] per task-struct memory footprint: 1536 bytes <6>[ 0.080931] Calibrating delay loop (skipped), value calculated using timer frequency.. 132.00 BogoMIPS (lpj=660000) <6>[ 0.091583] CPU: Testing write buffer coherency: ok <6>[ 0.096719] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.101993] pid_max: default: 32768 minimum: 301 <6>[ 0.107191] LSM: Security Framework initializing <6>[ 0.111812] LSM support for eBPF active <6>[ 0.115970] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123412] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.134860] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141392] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147764] rcu: Hierarchical SRCU implementation. <6>[ 0.159092] EFI services will not be available. <6>[ 0.162148] smp: Bringing up secondary CPUs ... <6>[ 0.168676] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.168692] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180452] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180466] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.191862] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.191876] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.200908] smp: Brought up 1 node, 4 CPUs <6>[ 0.204623] SMP: Total of 4 processors activated (528.00 BogoMIPS). <6>[ 0.211243] CPU: All CPU(s) started in SVC mode. <6>[ 0.218483] devtmpfs: initialized <6>[ 0.266241] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.273677] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.281588] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.293307] pinctrl core: initialized pinctrl subsystem <6>[ 0.302300] DMI not present or invalid. <6>[ 0.305756] NET: Registered protocol family 16 <6>[ 0.317926] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.330619] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.331117] cpuidle: using governor menu <6>[ 0.339236] CPU identified as i.MX6Q, silicon rev 1.0 <6>[ 0.970775] vdd1p1: supplied by regulator-dummy <6>[ 0.999481] vdd3p0: supplied by regulator-dummy <6>[ 1.027781] vdd2p5: supplied by regulator-dummy <6>[ 1.056081] vddarm: supplied by regulator-dummy <6>[ 1.085093] vddpu: supplied by regulator-dummy <6>[ 1.112526] vddsoc: supplied by regulator-dummy <6>[ 2.237239] No ATAGs? <6>[ 2.238033] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.245274] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.268067] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.297162] Serial: AMBA PL011 UART driver <6>[ 2.353719] Kprobes globally optimized <6>[ 2.455340] iommu: Default domain type: Translated <6>[ 2.459509] vgaarb: loaded <5>[ 2.464859] SCSI subsystem initialized <6>[ 2.467951] usbcore: registered new interface driver usbfs <6>[ 2.472103] usbcore: registered new interface driver hub <6>[ 2.477517] usbcore: registered new device driver usb <6>[ 2.489226] i2c i2c-0: IMX I2C adapter registered <6>[ 2.497311] i2c i2c-1: IMX I2C adapter registered <6>[ 2.503549] i2c i2c-2: IMX I2C adapter registered <6>[ 2.509718] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.512153] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.521602] PTP clock support registered <6>[ 2.540091] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.308620] NET: Registered protocol family 2 <6>[ 4.311241] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.321110] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.327125] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.335228] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.343935] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.350488] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.357031] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.363917] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.371675] NET: Registered protocol family 1 <6>[ 4.378034] RPC: Registered named UNIX socket transport module. <6>[ 4.381832] RPC: Registered udp transport module. <6>[ 4.386671] RPC: Registered tcp transport module. <6>[ 4.391695] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.398365] NET: Registered protocol family 44 <6>[ 4.403107] PCI: CLS 0 bytes, default 64 <6>[ 4.409316] Trying to unpack rootfs image as initramfs... <6>[ 6.246190] Freeing initrd memory: 15728K <4>[ 6.248502] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.256013] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.271464] Initialise system trusted keyrings <6>[ 6.274381] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.322064] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.328661] NFS: Registering the id_resolver key type <5>[ 6.331342] Key type id_resolver registered <5>[ 6.335596] Key type id_legacy registered <6>[ 6.340414] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.346872] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.354673] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.361025] Key type asymmetric registered <5>[ 6.363506] Asymmetric key parser 'x509' registered <6>[ 6.368850] bounce: pool size: 64 pages <6>[ 6.372851] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.380417] io scheduler mq-deadline registered <6>[ 6.385090] io scheduler kyber registered <4>[ 6.390256] test_firmware: interface ready <6>[ 6.546991] mxs-dma 110000.dma-controller: initialized <4>[ 6.605451] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.613564] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 6.820468] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.841973] SuperH (H)SCI(F) driver initialized <6>[ 6.846538] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 6.857431] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 6.863979] printk: console [ttymxc1] enabled <6>[ 6.863979] printk: console [ttymxc1] enabled <6>[ 6.872768] printk: bootconsole [ec_imx21] disabled <6>[ 6.872768] printk: bootconsole [ec_imx21] disabled <6>[ 6.888608] msm_serial: driver initialized <6>[ 6.894043] STMicroelectronics ASC driver initialized <6>[ 6.905168] STM32 USART driver initialized <6>[ 6.929417] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 6.949276] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 6.957893] panel-simple panel-lcd: Specify missing connector_type <4>[ 6.965807] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.014544] brd: module loaded <6>[ 7.059528] loop: module loaded <6>[ 7.065816] lkdtm: No crash points registered, enable through debugfs <6>[ 7.086278] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.094565] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.102913] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.111432] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.119637] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.128028] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.136083] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.147578] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.154943] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.164102] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.178158] scsi host0: ahci-imx <6>[ 7.183773] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.241743] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.254926] pps pps0: new PPS source ptp0 <6>[ 7.303245] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.313636] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.318895] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.325382] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.331116] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.356372] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.364245] usbcore: registered new interface driver pegasus <6>[ 7.370422] usbcore: registered new interface driver asix <6>[ 7.376240] usbcore: registered new interface driver ax88179_178a <6>[ 7.382811] usbcore: registered new interface driver cdc_ether <6>[ 7.389120] usbcore: registered new interface driver smsc75xx <6>[ 7.395383] usbcore: registered new interface driver smsc95xx <6>[ 7.401591] usbcore: registered new interface driver net1080 <6>[ 7.407663] usbcore: registered new interface driver cdc_subset <6>[ 7.414039] usbcore: registered new interface driver zaurus <6>[ 7.420212] usbcore: registered new interface driver cdc_ncm <6>[ 7.437487] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.444423] ehci-pci: EHCI PCI platform driver <6>[ 7.449296] ehci-platform: EHCI generic platform driver <6>[ 7.455751] ehci-orion: EHCI orion driver <6>[ 7.460886] SPEAr-ehci: EHCI SPEAr driver <6>[ 7.465932] ehci-st: EHCI STMicroelectronics driver <6>[ 7.471933] ehci-exynos: EHCI Exynos driver <6>[ 7.477147] ehci-atmel: EHCI Atmel driver <6>[ 7.482231] tegra-ehci: Tegra EHCI driver <6>[ 7.487297] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 7.493877] ohci-pci: OHCI PCI platform driver <6>[ 7.498764] ohci-platform: OHCI generic platform driver <6>[ 7.505165] SPEAr-ohci: OHCI SPEAr driver <6>[ 7.510264] ohci-st: OHCI STMicroelectronics driver <6>[ 7.516175] ohci-atmel: OHCI Atmel driver <6>[ 7.524326] usbcore: registered new interface driver usb-storage <6>[ 7.532477] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 7.538506] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 7.545135] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 7.559504] i2c /dev entries driver <6>[ 7.636083] sdhci: Secure Digital Host Controller Interface driver <6>[ 7.642617] sdhci: Copyright(c) Pierre Ossman <6>[ 7.655795] Synopsys Designware Multimedia Card Interface Driver <6>[ 7.668581] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 7.678112] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 7.683650] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 7.689801] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 7.696648] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 7.706414] usbcore: registered new interface driver usbhid <6>[ 7.712370] usbhid: USB HID core driver <6>[ 7.727390] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 7.736374] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 7.740672] netem: version 1.3 <6>[ 7.747131] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 7.755102] IPv4 over IPsec tunneling driver <6>[ 7.764056] NET: Registered protocol family 10 <6>[ 7.773652] mmc2: new high speed SDHC card at address 0001 <6>[ 7.774022] Segment Routing with IPv6 <6>[ 7.783248] mmcblk2: mmc2:0001 SD 14.8 GiB <6>[ 7.789135] NET: Registered protocol family 17 <6>[ 7.795461] 8021q: 802.1Q VLAN Support v1.8 <5>[ 7.800942] Key type dns_resolver registered <4>[ 7.809776] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 7.817189] ThumbEE CPU extension supported. <4>[ 7.817654] GPT:29296874 != 30965759 <5>[ 7.822222] Registering SWP/SWPB emulation handler <4>[ 7.825978] GPT:Alternate GPT header not at the end of the disk. <4>[ 7.825995] GPT:29296874 != 30965759 <5>[ 7.832603] Loading compiled-in X.509 certificates <4>[ 7.837426] GPT: Use GNU Parted to correct GPT errors. <6>[ 7.851967] mmcblk2: p1 p2 p3 <4>[ 8.028744] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.037499] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.051314] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.089531] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.103250] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.108813] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.141547] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.161035] hub 1-0:1.0: USB hub found <6>[ 8.167028] hub 1-0:1.0: 1 port detected <3>[ 8.182225] imx_thermal 20c8000.anatop:tempmon: invalid sensor calibration data <3>[ 8.189839] imx_thermal 20c8000.anatop:tempmon: error -EINVAL: failed to init from nvmem <4>[ 8.198359] imx_thermal: probe of 20c8000.anatop:tempmon failed with error -22 <4>[ 8.226477] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.235120] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.248827] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.281115] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.289660] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.303442] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.323867] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.354371] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.362973] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.376718] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.400355] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:06: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:06, irq=POLL) <6>[ 8.570338] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 8.778514] hub 1-1:1.0: USB hub found <6>[ 8.783512] hub 1-1:1.0: 3 ports detected <4>[ 8.815774] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.824383] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.838241] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 10.482313] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 10.510717] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 10.540125] Sending DHCP requests ., OK <6>[ 10.594710] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.12 <6>[ 10.603116] IP-Config: Complete: <6>[ 10.606641] device=eth0, hwaddr=0e:cc:7b:b0:7c:c7, ipaddr=192.168.201.12, mask=255.255.255.0, gw=192.168.201.1 <6>[ 10.617414] host=imx6q-sabrelite-lava-cbg-1, domain=lava-rack, nis-domain=(none) <6>[ 10.625609] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 10.625628] nameserver0=192.168.201.1 <6>[ 10.638404] clk: Disabling unused clocks <6>[ 10.695164] Freeing unused kernel memory: 2048K <6>[ 10.701614] Run /init as init process Loading, please wait... Starting systemd-udevd version 252.22-1~deb12u1 <6>[ 17.098336] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 17.126787] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.151218] panel-simple panel-lcd: Specify missing connector_type <6>[ 17.171125] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 17.188191] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 17.256861] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 17.276669] CAN device driver interface <4>[ 17.277318] panel-simple panel-lcd: Specify missing connector_type <4>[ 17.317688] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 17.393609] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.402333] panel-simple panel-lcd: Specify missing connector_type <6>[ 17.551554] caam 2100000.crypto: Entropy delay = 3200 <6>[ 17.556592] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 17.571646] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 17.581022] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 17.587897] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 17.617696] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 17.678459] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 17.684019] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 17.691008] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 17.714486] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <4>[ 17.717352] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 17.721176] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 17.735650] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 17.746682] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 1 <4>[ 17.777310] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.795487] panel-simple panel-lcd: Specify missing connector_type <4>[ 17.825937] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 17.828261] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 17.854597] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 17.919254] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 17.923743] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <4>[ 17.924469] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 17.925327] panel-simple panel-lcd: Specify missing connector_type <6>[ 17.951685] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <4>[ 17.962944] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 17.966455] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <4>[ 17.967421] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 17.988092] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 18.002218] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 18.011188] panel-simple panel-lcd: Specify missing connector_type <4>[ 18.078197] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 18.149908] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.158919] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.167845] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 18.176637] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 18.224231] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 18.233042] panel-simple panel-lcd: Specify missing connector_type <6>[ 18.853311] caam algorithms registered in /proc/crypto <6>[ 18.864163] caam 2100000.crypto: registering rng-caam <5>[ 18.993458] random: crng init done <4>[ 19.004533] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 19.054420] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 19.063220] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 19.072037] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 19.080743] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 19.096232] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 19.106036] panel-simple panel-lcd: Specify missing connector_type <4>[ 19.122169] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 19.160790] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 19.169466] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 19.178617] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 19.187392] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. Begin: Waiting up to 180 secs for any network device to become available ... done. IP-Config: eth0 hardware address 0e:cc:7b:b0:7c:c7 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.12 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-1 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 21.531947] systemd[1]: System time before build time, advancing clock. <30>[ 21.846168] systemd[1]: systemd 252.22-1~deb12u1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) <30>[ 21.883560] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 12 (bookworm)! <30>[ 21.946728] systemd[1]: Hostname set to . <30>[ 24.203704] systemd[1]: Queued start job for default target graphical.target. <30>[ 24.225392] systemd[1]: Created slice system-getty.slice - Slice /system/getty. [ OK ] Created slice system-getty.slice - Slice /system/getty. <30>[ 24.277803] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe. [ OK ] Created slice system-modpr…lice - Slice /system/modprobe. <30>[ 24.328854] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty. [ OK ] Created slice system-seria… - Slice /system/serial-getty. <30>[ 24.377045] systemd[1]: Created slice user.slice - User and Session Slice. [ OK ] Created slice user.slice - User and Session Slice. <30>[ 24.425491] systemd[1]: Started systemd-ask-password-console.path - Dispatch Password Requests to Console Directory Watch. [ OK ] Started systemd-ask-passwo…quests to Console Directory Watch. <30>[ 24.474753] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch. [ OK ] Started systemd-ask-passwo… Requests to Wall Directory Watch. <30>[ 24.522874] systemd[1]: proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point was skipped because of an unmet condition check (ConditionPathExists=/proc/sys/fs/binfmt_misc). <30>[ 24.544440] systemd[1]: Expecting device dev-ttymxc1.device - /dev/ttymxc1... Expecting device dev-ttymxc1.device - /dev/ttymxc1... <30>[ 24.581182] systemd[1]: Reached target cryptsetup.target - Local Encrypted Volumes. [ OK ] Reached target cryptsetup.…get - Local Encrypted Volumes. <30>[ 24.631672] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes. [ OK ] Reached target integrityse…Local Integrity Protected Volumes. <30>[ 24.682444] systemd[1]: Reached target paths.target - Path Units. [ OK ] Reached target paths.target - Path Units. <30>[ 24.720667] systemd[1]: Reached target remote-fs.target - Remote File Systems. [ OK ] Reached target remote-fs.target - Remote File Systems. <30>[ 24.761240] systemd[1]: Reached target slices.target - Slice Units. [ OK ] Reached target slices.target - Slice Units. <30>[ 24.802381] systemd[1]: Reached target swap.target - Swaps. [ OK ] Reached target swap.target - Swaps. <30>[ 24.841883] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes. [ OK ] Reached target veritysetup… - Local Verity Protected Volumes. <30>[ 24.894882] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe. [ OK ] Listening on systemd-initc… initctl Compatibility Named Pipe. <30>[ 25.003832] systemd[1]: systemd-journald-audit.socket - Journal Audit Socket was skipped because of an unmet condition check (ConditionSecurity=audit). <30>[ 25.023404] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log). [ OK ] Listening on systemd-journ…t - Journal Socket (/dev/log). <30>[ 25.087380] systemd[1]: Listening on systemd-journald.socket - Journal Socket. [ OK ] Listening on systemd-journald.socket - Journal Socket. <30>[ 25.137510] systemd[1]: Listening on systemd-networkd.socket - Network Service Netlink Socket. [ OK ] Listening on systemd-netwo… - Network Service Netlink Socket. <30>[ 25.192565] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket. [ OK ] Listening on systemd-udevd….socket - udev Control Socket. <30>[ 25.246618] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket. [ OK ] Listening on systemd-udevd…l.socket - udev Kernel Socket. <30>[ 25.295364] systemd[1]: dev-hugepages.mount - Huge Pages File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/mm/hugepages). <30>[ 25.313099] systemd[1]: dev-mqueue.mount - POSIX Message Queue File System was skipped because of an unmet condition check (ConditionPathExists=/proc/sys/fs/mqueue). <30>[ 25.340324] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System... Mounting sys-kernel-debug.… - Kernel Debug File System... <30>[ 25.392264] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System... Mounting sys-kernel-tracin… - Kernel Trace File System... <30>[ 25.448111] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes... Starting kmod-static-nodes…ate List of Static Device Nodes... <30>[ 25.514318] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs... Starting modprobe@configfs…m - Load Kernel Module configfs... <30>[ 25.583248] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod... Starting modprobe@dm_mod.s…[0m - Load Kernel Module dm_mod... <30>[ 25.643013] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm... Starting modprobe@drm.service - Load Kernel Module drm... <30>[ 25.703207] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore... Starting modprobe@efi_psto…- Load Kernel Module efi_pstore... <30>[ 25.776610] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse... Starting modprobe@fuse.ser…e - Load Kernel Module fuse... <30>[ 25.843075] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop... Starting modprobe@loop.ser…e - Load Kernel Module loop... <6>[ 25.873015] fuse: init (API version 7.32) <30>[ 25.915257] systemd[1]: Starting systemd-journald.service - Journal Service... Starting systemd-journald.service - Journal Service... <30>[ 25.989724] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules... Starting systemd-modules-l…rvice - Load Kernel Modules... <30>[ 26.042890] systemd[1]: Starting systemd-network-generator.service - Generate network units from Kernel command line... Starting systemd-network-g… units from Kernel command line... <30>[ 26.109590] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems... Starting systemd-remount-f…nt Root and Kernel File Systems... <30>[ 26.184425] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices... Starting systemd-udev-trig…[0m - Coldplug All udev Devices... <30>[ 26.274270] systemd[1]: Mounted sys-kernel-debug.mount - Kernel Debug File System. [ OK ] Mounted sys-kernel-debug.m…nt - Kernel Debug File System. <30>[ 26.332643] systemd[1]: Mounted sys-kernel-tracing.mount - Kernel Trace File System. [ OK ] Mounted sys-kernel-tracing…nt - Kernel Trace File System. <30>[ 26.378615] systemd[1]: Finished kmod-static-nodes.service - Create List of Static Device Nodes. [ OK ] Finished kmod-static-nodes…reate List of Static Device Nodes. <30>[ 26.475257] systemd[1]: modprobe@configfs.service: Deactivated successfully. <30>[ 26.486300] systemd[1]: Finished modprobe@configfs.service - Load Kernel Module configfs. [ OK ] Finished modprobe@configfs…[0m - Load Kernel Module configfs. <30>[ 26.537447] systemd[1]: modprobe@dm_mod.service: Deactivated successfully. <30>[ 26.548348] systemd[1]: Finished modprobe@dm_mod.service - Load Kernel Module dm_mod. [ OK ] Finished modprobe@dm_mod.s…e - Load Kernel Module dm_mod. <30>[ 26.607490] systemd[1]: modprobe@drm.service: Deactivated successfully. <30>[ 26.618144] systemd[1]: Finished modprobe@drm.service - Load Kernel Module drm. [ OK ] Finished modprobe@drm.service - Load Kernel Module drm. <30>[ 26.677491] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully. <30>[ 26.689304] systemd[1]: Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore. [ OK ] Finished modprobe@efi_psto…m - Load Kernel Module efi_pstore. <30>[ 26.747878] systemd[1]: modprobe@fuse.service: Deactivated successfully. <30>[ 26.758642] systemd[1]: Finished modprobe@fuse.service - Load Kernel Module fuse. [ OK ] Finished modprobe@fuse.service - Load Kernel Module fuse. <30>[ 26.807410] systemd[1]: modprobe@loop.service: Deactivated successfully. <30>[ 26.818709] systemd[1]: Finished modprobe@loop.service - Load Kernel Module loop. [ OK ] Finished modprobe@loop.service - Load Kernel Module loop. <30>[ 26.872506] systemd[1]: Started systemd-journald.service - Journal Service. [ OK ] Started systemd-journald.service - Journal Service. [ OK ] Finished systemd-modules-l…service - Load Kernel Modules. [ OK ] Finished systemd-network-g…rk units from Kernel command line. [ OK ] Finished systemd-remount-f…ount Root and Kernel File Systems. [ OK ] Reached target network-pre…get - Preparation for Network. Mounting sys-fs-fuse-conne… - FUSE Control File System... Mounting sys-kernel-config…ernel Configuration File System... Starting systemd-journal-f…h Journal to Persistent Storage... Starting systemd-random-se…ice - Load/Save Random Seed... Starting systemd-sysctl.se…ce - Apply Kernel Variables... Starting systemd-sysusers.…rvice - Creat<46>[ 27.370884] systemd-journald[302]: Received client request to flush runtime journal. e System Users... [ OK ] Mounted sys-fs-fuse-connec…nt - FUSE Control File System. [ OK ] Mounted sys-kernel-config.… Kernel Configuration File System. [ OK ] Finished systemd-random-se…rvice - Load/Save Random Seed. [ OK ] Finished systemd-sysctl.service - Apply Kernel Variables. [ OK ] Finished systemd-sysusers.service - Create System Users. Starting systemd-tmpfiles-…ate Static Device Nodes in /dev... [ OK ] Finished systemd-tmpfiles-…reate Static Device Nodes in /dev. [ OK ] Reached target local-fs-pr…reparation for Local File Systems. [ OK ] Reached target local-fs.target - Local File Systems. Starting systemd-udevd.ser…ger for Device Events and Files... [ OK ] Finished systemd-journal-f…ush Journal to Persistent Storage. Starting systemd-tmpfiles-… Volatile Files and Directories... [ OK ] Started systemd-udevd.serv…nager for Device Events and Files. Starting systemd-networkd.…ice - Network Configuration... [ OK ] Finished systemd-tmpfiles-…te Volatile Files and Directories. Starting systemd-timesyncd… - Network Time Synchronization... Starting systemd-update-ut…rd System Boot/Shutdown in UTMP... [ OK ] Finished systemd-update-ut…cord System Boot/Shutdown in UTMP. <5>[ 30.744798] cfg80211: Loading compiled-in X.509 certificates for regulatory database <5>[ 31.003678] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <5>[ 31.013277] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 31.025362] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 31.034504] cfg80211: failed to load regulatory.db [ OK ] Started systemd-networkd.service - Network Configuration. [ OK ] Reached target network.target - Network. [ OK ] Started systemd-timesyncd.…0m - Network Time Synchronization. [ OK ] Reached target time-set.target - System Time Set. <46>[ 31.607941] systemd-journald[302]: Oldest entry in /var/log/journal/658c871cd7314ccea6115dc5728f8992/system.journal is older than the configured file retention duration (1month), suggesting rotation. <46>[ 31.626421] systemd-journald[302]: /var/log/journal/658c871cd7314ccea6115dc5728f8992/system.journal: Journal header limits reached or header out-of-date, rotating. [ OK ] Found device dev-ttymxc1.device - /dev/ttymxc1. [ OK ] Finished systemd-udev-trig…e - Coldplug All udev Devices. [ OK ] Reached target sysinit.target - System Initialization. [ OK ] Started apt-daily.timer - Daily apt download activities. [ OK ] Started apt-daily-upgrade.… apt upgrade and clean activities. [ OK ] Started dpkg-db-backup.tim… Daily dpkg database backup timer. [ OK ] Started e2scrub_all.timer…etadata Check for All Filesystems. [ OK ] Started fstrim.timer - Discard unused blocks once a week. [ OK ] Started systemd-tmpfiles-c… Cleanup of Temporary Directories. [ OK ] Reached target timers.target - Timer Units. [ OK ] Reached target usb-gadget.…m - Hardware activated USB gadget. [ OK ] Listening on dbus.socket[…- D-Bus System Message Bus Socket. [ OK ] Reached target sockets.target - Socket Units. [ OK ] Listening on systemd-rfkil…l Switch Status /dev/rfkill Watch. [ OK ] Reached target basic.target - Basic System. Starting dbus.service - D-Bus System Message Bus... Starting e2scrub_reap.serv…e ext4 Metadata Check Snapshots... Starting systemd-logind.se…ice - User Login Management... Starting systemd-user-sess…vice - Permit User Sessions... [ OK ] Finished systemd-user-sess…ervice - Permit User Sessions. [ OK ] Started getty@tty1.service - Getty on tty1. [ OK ] Started serial-getty@ttymx…ice - Serial Getty on ttymxc1. [ OK ] Reached target getty.target - Login Prompts. [ OK ] Started dbus.service - D-Bus System Message Bus. [ OK ] Finished e2scrub_reap.serv…ine ext4 Metadata Check Snapshots. [ OK ] Started systemd-logind.service - User Login Management. [ OK ] Reached target multi-user.target - Multi-User System. [ OK ] Reached target graphical.target - Graphical Interface. Starting systemd-update-ut… Record Runlevel Change in UTMP... [ OK ] Finished systemd-update-ut… - Record Runlevel Change in UTMP. Debian GNU/Linux 12 debian-bookworm-armhf ttymxc1 debian-bookworm-armhf login: root (automatic login) Linux debian-bookworm-armhf 5.10.216-cip47 #1 SMP Thu May 30 07:51:22 UTC 2024 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/14091013/extract-nfsrootfs-0neqtv6e' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/14091013/extract-nfsrootfs-0neqtv6e' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-14091013/environment . /lava-14091013/environment / # /lava-14091013/bin/lava-test-runner /lava-14091013/0 /lava-14091013/bin/lava-test-runner /lava-14091013/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-14091013/0/tests/0_timesync-off ++ cat uuid + UUID=14091013_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-lib + TESTRUN_ID=1_kselftest-lib + cd /lava-14091013/0/tests/1_kselftest-lib ++ cat uuid + UUID=14091013_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c lib -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.216-cip47-47-g42df769f88c3/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz -L '' -S /dev/null -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: install_deps skipped --2024-05-30 08:07:06-- http://storage.kernelci.org/cip-gitlab/ci-iwamatsu-linux-5.10.y-cip-rc/v5.10.216-cip47-47-g42df769f88c3/arm/multi_v7_defconfig+kselftest/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 20.171.243.82 Connecting to storage.kernelci.org (storage.kernelci.org)|20.171.243.82|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1345960 (1.3M) [application/octet-stream] Saving to: 'kselftest_armhf.tar.gz' kselftest_armhf.tar 0%[ ] 0 --.-KB/s kselftest_armhf.tar 3%[ ] 49.22K 191KB/s kselftest_armhf.tar 16%[==> ] 219.84K 426KB/s kselftest_armhf.tar 63%[===========> ] 841.10K 985KB/s kselftest_armhf.tar 100%[===================>] 1.28M 1.37MB/s in 0.9s 2024-05-30 08:07:08 (1.37 MB/s) - 'kselftest_armhf.tar.gz' saved [1345960/1345960] skiplist: ======================================== ======================================== lib:printf.sh lib:bitmap.sh lib:prime_numbers.sh lib:strscpy.sh ============== Tests to run =============== lib:printf.sh lib:bitmap.sh lib:prime_numbers.sh lib:strscpy.sh ===========End Tests to run =============== shardfile-lib pass <12>[ 65.145500] kselftest: Running tests in lib TAP version 13 1..4 # selftests: lib: printf.sh <6>[ 65.678839] test_printf: loaded. <6>[ 65.685931] test_printf: all 384 tests passed <6>[ 65.750180] test_printf: unloaded. # printf: ok ok 1 selftests: lib: printf.sh # selftests: lib: bitmap.sh <6>[ 66.135221] test_bitmap: loaded. <3>[ 66.139607] test_bitmap: parselist: 14: input is '0-2047:128/256' OK, Time: 4182 <6>[ 66.163771] test_bitmap: all 1679 tests passed <6>[ 66.216444] test_bitmap: unloaded. # bitmap: ok ok 2 selftests: lib: bitmap.sh # selftests: lib: prime_numbers.sh <6>[ 67.377169] prime numbers: selftest(65536) passed, last prime was 65521 # prime numbers: ok ok 3 selftests: lib: prime_numbers.sh # selftests: lib: strscpy.sh <6>[ 67.822445] test_strscpy: loaded. <6>[ 67.826076] test_strscpy: all 32 tests passed <6>[ 67.879409] test_strscpy: unloaded. # strscpy*: ok ok 4 selftests: lib: strscpy.sh <4>[ 69.606479] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 69.615335] panel-simple panel-lcd: Specify missing connector_type <4>[ 69.629446] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 69.668955] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 69.677863] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 69.686881] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 69.695710] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 69.715316] platform panel-lcd: deferred probe pending <6>[ 69.721200] platform panel-lvds0: deferred probe pending <6>[ 69.726822] platform backlight-lcd: deferred probe pending <6>[ 69.732693] platform backlight-lvds: deferred probe pending <6>[ 69.738575] platform disp0: deferred probe pending lib_printf_sh pass lib_bitmap_sh pass lib_prime_numbers_sh pass lib_strscpy_sh pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #