[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 14091015/tftp-deploy-7s41rn4l/kernel/zImage tftp 0x10000000 14091015/tftp-deploy-7s41rn4l/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '14091015/tftp-deploy-7s41rn4l/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 6.3 MiB/s done Bytes transferred = 12558848 (bfa200 hex) => tftp 0x14000000 14091015/tftp-deploy-7s41rn4l/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 14091015/tftp-deploy-7s41rn4l/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '14091015/tftp-deploy-7s41rn4l/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############## 5.8 MiB/s done Bytes transferred = 19275992 (12620d8 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 14091015/tftp-deploy-7s41rn4l/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 14091015/tftp-deploy-7s41rn4l/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '14091015/tftp-deploy-7s41rn4l/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 10.2 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbfa200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19275928 Bytes = 18.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.216-cip47 (KernelCI@build-j211253-arm-gcc-10-multi-v7-defconfig-kselftest-hpld9) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu May 30 07:51:22 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917628K/1048576K available (17408K kernel code, 2714K rwdata, 8152K rodata, 2048K init, 6693K bss, 65412K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 56169 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000009] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022931] Console: colour dummy device 80x30 <4>[ 0.024832] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032845] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037190] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041602] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046238] ... CLASSHASH_SIZE: 4096 <4>[ 0.050822] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055544] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060218] ... CHAINHASH_SIZE: 32768 <4>[ 0.064917] memory used by lock dependency info: 4061 kB <4>[ 0.070596] memory used for stack traces: 2112 kB <4>[ 0.075642] per task-struct memory footprint: 1536 bytes <6>[ 0.081331] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091746] CPU: Testing write buffer coherency: ok <6>[ 0.096882] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102155] pid_max: default: 32768 minimum: 301 <6>[ 0.107355] LSM: Security Framework initializing <6>[ 0.111973] LSM support for eBPF active <6>[ 0.116128] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123577] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.135018] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141518] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147870] rcu: Hierarchical SRCU implementation. <6>[ 0.159239] EFI services will not be available. <6>[ 0.162286] smp: Bringing up secondary CPUs ... <6>[ 0.168809] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.168824] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180585] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180600] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.192024] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.192039] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.201071] smp: Brought up 1 node, 4 CPUs <6>[ 0.204784] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211320] CPU: All CPU(s) started in SVC mode. <6>[ 0.218546] devtmpfs: initialized <6>[ 0.266373] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.273813] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.281726] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.293428] pinctrl core: initialized pinctrl subsystem <6>[ 0.302395] DMI not present or invalid. <6>[ 0.305871] NET: Registered protocol family 16 <6>[ 0.318058] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.330749] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.331252] cpuidle: using governor menu <6>[ 0.339355] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.970631] vdd1p1: supplied by regulator-dummy <6>[ 0.999266] vdd3p0: supplied by regulator-dummy <6>[ 1.027557] vdd2p5: supplied by regulator-dummy <6>[ 1.055868] vddarm: supplied by regulator-dummy <6>[ 1.084878] vddpu: supplied by regulator-dummy <6>[ 1.112365] vddsoc: supplied by regulator-dummy <6>[ 2.236997] No ATAGs? <6>[ 2.237811] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.244971] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.267724] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.296746] Serial: AMBA PL011 UART driver <6>[ 2.352878] Kprobes globally optimized <6>[ 2.454728] iommu: Default domain type: Translated <6>[ 2.459227] vgaarb: loaded <5>[ 2.464208] SCSI subsystem initialized <6>[ 2.467396] usbcore: registered new interface driver usbfs <6>[ 2.471366] usbcore: registered new interface driver hub <6>[ 2.476956] usbcore: registered new device driver usb <6>[ 2.488622] i2c i2c-0: IMX I2C adapter registered <6>[ 2.496902] i2c i2c-1: IMX I2C adapter registered <6>[ 2.502960] i2c i2c-2: IMX I2C adapter registered <6>[ 2.509178] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.511574] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.521074] PTP clock support registered <6>[ 2.540612] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.308507] NET: Registered protocol family 2 <6>[ 4.311101] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.321494] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.327504] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.335606] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.344320] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.350816] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.357414] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.364317] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.372044] NET: Registered protocol family 1 <6>[ 4.378378] RPC: Registered named UNIX socket transport module. <6>[ 4.382204] RPC: Registered udp transport module. <6>[ 4.387054] RPC: Registered tcp transport module. <6>[ 4.392077] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.398735] NET: Registered protocol family 44 <6>[ 4.403498] PCI: CLS 0 bytes, default 64 <6>[ 4.409823] Trying to unpack rootfs image as initramfs... <6>[ 6.786411] Freeing initrd memory: 18828K <4>[ 6.788855] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.796594] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.811679] Initialise system trusted keyrings <6>[ 6.814543] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.862319] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.868713] NFS: Registering the id_resolver key type <5>[ 6.871435] Key type id_resolver registered <5>[ 6.875645] Key type id_legacy registered <6>[ 6.880482] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.886922] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.894724] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.900993] Key type asymmetric registered <5>[ 6.903557] Asymmetric key parser 'x509' registered <6>[ 6.908904] bounce: pool size: 64 pages <6>[ 6.912883] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.920463] io scheduler mq-deadline registered <6>[ 6.925143] io scheduler kyber registered <4>[ 6.930214] test_firmware: interface ready <6>[ 7.087053] mxs-dma 110000.dma-controller: initialized <4>[ 7.145496] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.153668] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 7.360759] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.382384] SuperH (H)SCI(F) driver initialized <6>[ 7.386957] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.397810] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.404368] printk: console [ttymxc1] enabled <6>[ 7.404368] printk: console [ttymxc1] enabled <6>[ 7.413146] printk: bootconsole [ec_imx21] disabled <6>[ 7.413146] printk: bootconsole [ec_imx21] disabled <6>[ 7.428954] msm_serial: driver initialized <6>[ 7.434391] STMicroelectronics ASC driver initialized <6>[ 7.445564] STM32 USART driver initialized <6>[ 7.469908] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.489750] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.498342] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.506245] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.555282] brd: module loaded <6>[ 7.600533] loop: module loaded <6>[ 7.606680] lkdtm: No crash points registered, enable through debugfs <6>[ 7.627156] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.635451] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.643805] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.652328] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.660585] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.668918] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.676881] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.688455] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.695816] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.704974] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.719059] scsi host0: ahci-imx <6>[ 7.724723] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.782548] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.795743] pps pps0: new PPS source ptp0 <6>[ 7.854944] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.865318] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.870622] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.877056] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.882788] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.908043] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.915919] usbcore: registered new interface driver pegasus <6>[ 7.922099] usbcore: registered new interface driver asix <6>[ 7.927916] usbcore: registered new interface driver ax88179_178a <6>[ 7.934469] usbcore: registered new interface driver cdc_ether <6>[ 7.940839] usbcore: registered new interface driver smsc75xx <6>[ 7.947083] usbcore: registered new interface driver smsc95xx <6>[ 7.953293] usbcore: registered new interface driver net1080 <6>[ 7.959361] usbcore: registered new interface driver cdc_subset <6>[ 7.965743] usbcore: registered new interface driver zaurus <6>[ 7.971891] usbcore: registered new interface driver cdc_ncm <6>[ 7.989244] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 7.996179] ehci-pci: EHCI PCI platform driver <6>[ 8.001103] ehci-platform: EHCI generic platform driver <6>[ 8.007538] ehci-orion: EHCI orion driver <6>[ 8.012682] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.017771] ehci-st: EHCI STMicroelectronics driver <6>[ 8.023728] ehci-exynos: EHCI Exynos driver <6>[ 8.028927] ehci-atmel: EHCI Atmel driver <6>[ 8.034011] tegra-ehci: Tegra EHCI driver <6>[ 8.039081] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.045658] ohci-pci: OHCI PCI platform driver <6>[ 8.050575] ohci-platform: OHCI generic platform driver <6>[ 8.056926] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.062035] ohci-st: OHCI STMicroelectronics driver <6>[ 8.067951] ohci-atmel: OHCI Atmel driver <6>[ 8.072822] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.076106] usbcore: registered new interface driver usb-storage <6>[ 8.078847] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.091550] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.113767] i2c /dev entries driver <6>[ 8.189615] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.196148] sdhci: Copyright(c) Pierre Ossman <6>[ 8.209274] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.222141] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.231672] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.237121] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.243311] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.250667] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.260439] usbcore: registered new interface driver usbhid <6>[ 8.266308] usbhid: USB HID core driver <6>[ 8.280807] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.293418] netem: version 1.3 <6>[ 8.293731] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.297003] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.312061] IPv4 over IPsec tunneling driver <6>[ 8.321038] NET: Registered protocol family 10 <6>[ 8.330797] mmc2: new high speed SDHC card at address e624 <6>[ 8.331125] Segment Routing with IPv6 <6>[ 8.340208] mmcblk2: mmc2:e624 SL16G 14.8 GiB <6>[ 8.346335] NET: Registered protocol family 17 <6>[ 8.352893] 8021q: 802.1Q VLAN Support v1.8 <5>[ 8.358299] Key type dns_resolver registered <4>[ 8.368387] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 8.376258] GPT:7812499 != 31116287 <6>[ 8.376660] ThumbEE CPU extension supported. <4>[ 8.380038] GPT:Alternate GPT header not at the end of the disk. <5>[ 8.384708] Registering SWP/SWPB emulation handler <4>[ 8.390950] GPT:7812499 != 31116287 <4>[ 8.390967] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.405365] mmcblk2: p1 p2 p3 <5>[ 8.406011] Loading compiled-in X.509 certificates <4>[ 8.566077] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.574602] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.586947] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.624398] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.639231] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.644804] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.680920] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.699769] hub 1-0:1.0: USB hub found <6>[ 8.704378] hub 1-0:1.0: 1 port detected <6>[ 8.719015] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.748280] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.756796] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.769123] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.796431] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.804981] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.817268] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.834518] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.860807] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.869223] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.881781] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.902531] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 9.090864] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.298781] hub 1-1:1.0: USB hub found <6>[ 9.303633] hub 1-1:1.0: 3 ports detected <4>[ 9.332416] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.340874] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.353409] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 12.002270] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 12.011955] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 12.040490] Sending DHCP requests ., OK <6>[ 12.085000] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 12.093383] IP-Config: Complete: <6>[ 12.096906] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 12.107705] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 12.115900] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 12.115920] nameserver0=192.168.201.1 <6>[ 12.128555] clk: Disabling unused clocks <6>[ 12.177987] Freeing unused kernel memory: 2048K <6>[ 12.203234] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 12.607222] udevd[136]: starting version 3.2.9 <5>[ 12.615178] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.622917] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.629804] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 12.649435] udevd[136]: specified user 'tss' unknown <27>[ 12.655040] udevd[136]: specified group 'tss' unknown <30>[ 12.668315] udevd[137]: starting eudev-3.2.9 <6>[ 13.940614] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 13.956310] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 13.983218] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.051323] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.067297] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 14.167814] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.201028] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.206741] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.225577] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.241011] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.250041] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.259114] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.417718] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 14.456344] CAN device driver interface <4>[ 14.471080] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.483869] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.567453] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.590912] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.660773] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.667621] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 14.720180] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 14.744594] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 14.751129] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 14.764962] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 1 <6>[ 14.782619] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.791541] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.800245] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.809012] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.941719] caam 2100000.crypto: Entropy delay = 3200 <6>[ 15.007862] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 15.068634] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 15.074157] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 15.081146] caam 2100000.crypto: job rings = 2, qi = 0 <4>[ 15.114837] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.123458] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.144700] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.188509] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.197361] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.206158] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.214939] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.255585] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 15.278135] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.285308] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 15.286455] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 15.287279] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 15.298725] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.322776] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.350819] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.359486] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.368399] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.377268] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.422312] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.430925] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.445026] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.466499] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.475458] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.484246] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.492961] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.524836] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.533418] panel-simple panel-lcd: Specify missing connector_type <6>[ 16.086238] caam algorithms registered in /proc/crypto <6>[ 16.103575] caam 2100000.crypto: registering rng-caam <4>[ 16.115480] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.135561] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.144335] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.153082] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.161799] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.189521] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.199074] panel-simple panel-lcd: Specify missing connector_type <4>[ 16.212673] panel-simple panel-lvds0: supply power not found, using dummy regulator done <6>[ 16.234171] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.243304] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.252378] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) Saving random seed: <6>[ 16.261100] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <5>[ 16.292352] random: crng init done <5>[ 16.296112] random: 1 urandom warning(s) missed due to ratelimiting OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-14091015/environment . /lava-14091015/environment / # /lava-14091015/bin/lava-test-runner /lava-14091015/0 /lava-14091015/bin/lava-test-runner /lava-14091015/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-14091015/0/tests/0_dmesg + cat uuid + UUID=14091015_1.5.2.4.1<8>[ 17.391921] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.515753] <8>[ 17.630719] <8>[ 17.746403] + set +x <8>[ 17.758218] / #