[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff =>setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.11 (7 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 14091008/tftp-deploy-975j7etq/kernel/zImage tftp 0x10000000 14091008/tftp-deploy-975j7etq/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '14091008/tftp-deploy-975j7etq/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 5 MiB/s done Bytes transferred = 9716224 (944200 hex) => tftp 0x14000000 14091008/tftp-deploy-975j7etq/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 14091008/tftp-deploy-975j7etq/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '14091008/tftp-deploy-975j7etq/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.1 MiB/s done Bytes transferred = 16085208 (f570d8 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 14091008/tftp-deploy-975j7etq/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 14091008/tftp-deploy-975j7etq/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.11 Filename '14091008/tftp-deploy-975j7etq/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.7 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x944200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16085144 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.216-cip47 (KernelCI@build-j211205-arm-gcc-10-multi-v7-defconfig-qmwcm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu May 30 07:46:39 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 932640K/1048576K available (14336K kernel code, 2240K rwdata, 5368K rodata, 2048K init, 428K bss, 50400K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022219] Console: colour dummy device 80x30 <6>[ 0.024108] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034519] CPU: Testing write buffer coherency: ok <6>[ 0.039652] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.044949] pid_max: default: 32768 minimum: 301 <6>[ 0.049982] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.057414] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.066302] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072025] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079721] rcu: Hierarchical SRCU implementation. <6>[ 0.086692] EFI services will not be available. <6>[ 0.088928] smp: Bringing up secondary CPUs ... <6>[ 0.094209] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094217] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105559] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105567] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116776] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116784] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127214] smp: Brought up 1 node, 4 CPUs <6>[ 0.131438] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137895] CPU: All CPU(s) started in SVC mode. <6>[ 0.143335] devtmpfs: initialized <6>[ 0.153610] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158949] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168822] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179027] pinctrl core: initialized pinctrl subsystem <6>[ 0.183490] DMI not present or invalid. <6>[ 0.186610] NET: Registered protocol family 16 <6>[ 0.193902] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200535] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200716] cpuidle: using governor menu <6>[ 0.208815] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.388194] vdd1p1: supplied by regulator-dummy <6>[ 0.397328] vdd3p0: supplied by regulator-dummy <6>[ 0.406381] vdd2p5: supplied by regulator-dummy <6>[ 0.415456] vddarm: supplied by regulator-dummy <6>[ 0.424718] vddpu: supplied by regulator-dummy <6>[ 0.433583] vddsoc: supplied by regulator-dummy <6>[ 0.762186] No ATAGs? <6>[ 0.762376] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.770148] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.780417] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.790925] Serial: AMBA PL011 UART driver <6>[ 0.795167] printk: console [ramoops-1] enabled <6>[ 0.797461] pstore: Registered ramoops as persistent store backend <6>[ 0.803654] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.841542] iommu: Default domain type: Translated <6>[ 0.844274] vgaarb: loaded <5>[ 0.847692] SCSI subsystem initialized <6>[ 0.851413] usbcore: registered new interface driver usbfs <6>[ 0.856615] usbcore: registered new interface driver hub <6>[ 0.862139] usbcore: registered new device driver usb <6>[ 0.868988] i2c i2c-0: IMX I2C adapter registered <6>[ 0.873706] i2c i2c-1: IMX I2C adapter registered <6>[ 0.878187] i2c i2c-2: IMX I2C adapter registered <6>[ 0.883665] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.887528] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.896931] PTP clock support registered <6>[ 0.904719] clocksource: Switched to clocksource mxc_timer1 <6>[ 2.014082] NET: Registered protocol family 2 <6>[ 2.016357] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 2.024883] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.032156] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 2.040238] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.047680] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 2.054328] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.061087] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 2.068513] NET: Registered protocol family 1 <6>[ 2.073606] RPC: Registered named UNIX socket transport module. <6>[ 2.079147] RPC: Registered udp transport module. <6>[ 2.084061] RPC: Registered tcp transport module. <6>[ 2.089050] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.095744] PCI: CLS 0 bytes, default 64 <6>[ 2.100413] Trying to unpack rootfs image as initramfs... <6>[ 3.450284] Freeing initrd memory: 15712K <4>[ 3.452283] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.459553] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.469338] Initialise system trusted keyrings <6>[ 3.472496] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.484759] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.488734] NFS: Registering the id_resolver key type <5>[ 3.493358] Key type id_resolver registered <5>[ 3.497774] Key type id_legacy registered <6>[ 3.502114] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.508993] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.516680] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.521716] Key type asymmetric registered <5>[ 3.525618] Asymmetric key parser 'x509' registered <6>[ 3.530766] bounce: pool size: 64 pages <6>[ 3.534865] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.542470] io scheduler mq-deadline registered <6>[ 3.547270] io scheduler kyber registered <6>[ 3.592531] mxs-dma 110000.dma-controller: initialized <4>[ 3.599960] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.607777] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 3.668737] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.677098] SuperH (H)SCI(F) driver initialized <6>[ 3.680058] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.688947] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.696848] printk: console [ttymxc1] enabled <6>[ 3.696848] printk: console [ttymxc1] enabled <6>[ 3.706017] printk: bootconsole [ec_imx21] disabled <6>[ 3.706017] printk: bootconsole [ec_imx21] disabled <6>[ 3.717740] msm_serial: driver initialized <6>[ 3.723731] STMicroelectronics ASC driver initialized <6>[ 3.731103] STM32 USART driver initialized <4>[ 3.746203] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.754107] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.760942] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.777616] brd: module loaded <6>[ 3.788418] loop: module loaded <6>[ 3.795984] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.804178] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.812474] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.820935] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.828954] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.836689] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.844233] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.854846] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.862102] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.871185] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.882025] scsi host0: ahci-imx <6>[ 3.885913] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.906968] CAN device driver interface <6>[ 3.912459] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.921993] pps pps0: new PPS source ptp0 <6>[ 3.959032] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.966709] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.971945] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.978214] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.983881] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.996175] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.003889] usbcore: registered new interface driver pegasus <6>[ 4.009882] usbcore: registered new interface driver asix <6>[ 4.015600] usbcore: registered new interface driver ax88179_178a <6>[ 4.021991] usbcore: registered new interface driver cdc_ether <6>[ 4.028153] usbcore: registered new interface driver smsc75xx <6>[ 4.034209] usbcore: registered new interface driver smsc95xx <6>[ 4.040282] usbcore: registered new interface driver net1080 <6>[ 4.046259] usbcore: registered new interface driver cdc_subset <6>[ 4.052475] usbcore: registered new interface driver zaurus <6>[ 4.058399] usbcore: registered new interface driver cdc_ncm <6>[ 4.068067] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.074885] ehci-pci: EHCI PCI platform driver <6>[ 4.079638] ehci-platform: EHCI generic platform driver <6>[ 4.085472] ehci-orion: EHCI orion driver <6>[ 4.089976] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.094450] ehci-st: EHCI STMicroelectronics driver <6>[ 4.099812] ehci-exynos: EHCI Exynos driver <6>[ 4.104453] ehci-atmel: EHCI Atmel driver <6>[ 4.108941] tegra-ehci: Tegra EHCI driver <6>[ 4.113445] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.119928] ohci-pci: OHCI PCI platform driver <6>[ 4.124703] ohci-platform: OHCI generic platform driver <6>[ 4.130481] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.134991] ohci-st: OHCI STMicroelectronics driver <6>[ 4.140343] ohci-atmel: OHCI Atmel driver <6>[ 4.145940] usbcore: registered new interface driver usb-storage <6>[ 4.160857] i2c /dev entries driver <6>[ 4.185702] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.192154] sdhci: Copyright(c) Pierre Ossman <6>[ 4.199699] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.208078] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.215317] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.219719] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.220605] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.231391] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.237742] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.238814] usbcore: registered new interface driver usbhid <6>[ 4.243455] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.249266] usbhid: USB HID core driver <6>[ 4.256206] NET: Registered protocol family 10 <6>[ 4.259919] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.262657] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.265700] Segment Routing with IPv6 <6>[ 4.279356] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.283185] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.297032] NET: Registered protocol family 17 <6>[ 4.300218] mmc2: new high speed SDHC card at address 0001 <6>[ 4.301756] can: controller area network core <6>[ 4.308386] mmcblk2: mmc2:0001 SD 14.6 GiB <6>[ 4.312236] NET: Registered protocol family 29 <6>[ 4.321337] can: raw protocol <6>[ 4.324580] can: broadcast manager protocol <6>[ 4.329062] can: netlink gateway - max_hops=1 <4>[ 4.329688] GPT:Primary header thinks Alt. header is not at the end of the disk. <5>[ 4.334190] Key type dns_resolver registered <4>[ 4.341390] GPT:29296874 != 30560255 <4>[ 4.349775] GPT:Alternate GPT header not at the end of the disk. <6>[ 4.351732] ThumbEE CPU extension supported. <4>[ 4.356076] GPT:29296874 != 30560255 <4>[ 4.356080] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.356136] mmcblk2: p1 p2 p3 <5>[ 4.360632] Registering SWP/SWPB emulation handler <5>[ 4.378592] Loading compiled-in X.509 certificates <6>[ 4.388691] pstore: Using crash dump compression: deflate <4>[ 4.416272] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.424164] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.432117] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.448541] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.458446] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.463611] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.494825] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.502003] hub 1-0:1.0: USB hub found <6>[ 4.506150] hub 1-0:1.0: 1 port detected <6>[ 4.514783] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.531647] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.539570] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.547520] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.559657] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.567562] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.575464] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.585481] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.597655] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.605569] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.613488] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.627353] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.834758] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 5.036353] hub 1-1:1.0: USB hub found <6>[ 5.040589] hub 1-1:1.0: 3 ports detected <4>[ 5.051192] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 5.059158] panel-simple panel-lcd: Specify missing connector_type <4>[ 5.067483] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 6.725294] fec 2188000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 6.734807] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.764703] Sending DHCP requests ., OK <6>[ 6.808939] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.11 <6>[ 6.817243] IP-Config: Complete: <6>[ 6.820746] device=eth0, hwaddr=00:19:b8:07:40:03, ipaddr=192.168.201.11, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.831459] host=imx6q-sabrelite-lava-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 6.839580] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.839586] nameserver0=192.168.201.1 <6>[ 6.851591] clk: Disabling unused clocks <6>[ 6.861832] Freeing unused kernel memory: 2048K <6>[ 6.915742] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.045863] udevd[133]: starting version 3.2.9 <5>[ 7.051624] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.058742] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.065981] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.079954] udevd[133]: specified user 'tss' unknown <27>[ 7.085456] udevd[133]: specified group 'tss' unknown <30>[ 7.093163] udevd[134]: starting eudev-3.2.9 <6>[ 7.410243] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 7.426519] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.434490] panel-simple panel-lcd: Specify missing connector_type <6>[ 7.442358] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 7.453227] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 7.467133] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.475100] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.483392] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.606878] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 7.615537] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <4>[ 7.618466] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 7.624118] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <4>[ 7.632301] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <6>[ 7.640578] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 7.653131] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.664847] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.698734] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.726005] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.765101] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.802083] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.808954] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.836155] caam 2100000.crypto: Entropy delay = 3200 <6>[ 7.902275] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 7.963035] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 7.968475] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 7.975387] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 7.985171] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.004839] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.011236] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.028664] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 0 <6>[ 8.053026] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.061641] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.070271] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.078867] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.098888] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.106941] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.129817] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.133007] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.149054] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 8.158484] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.167079] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.175690] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.184207] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.206806] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.214879] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.224660] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.254623] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.263280] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.271966] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.280558] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.469988] caam algorithms registered in /proc/crypto <6>[ 8.477472] caam 2100000.crypto: registering rng-caam <4>[ 8.484783] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.492756] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.501497] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.516122] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.524617] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.533191] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) done <6>[ 8.541724] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Saving random seed: <4>[ 8.562329] panel-simple panel-lcd: supply power not found, using dummy regulator <5>[ 8.563657] random: dd: uninitialized urandom read (32 bytes read) <4>[ 8.570296] panel-simple panel-lcd: Specify missing connector_type OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.665291] random: crng init done <5>[ 8.668990] random: 1 urandom warning(s) missed due to ratelimiting OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-14091008/environment . /lava-14091008/environment / # /lava-14091008/bin/lava-test-runner /lava-14091008/0 /lava-14091008/bin/lava-test-runner /lava-14091008/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-14091008/0/tests/0_dmesg + <8>[ 9.271086] cat uuid + UUID=14091008_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 9.314836] <8>[ 9.356127] <8>[ 9.397236] + set<8>[ 9.407149] +x / #