[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (4 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 14571401/tftp-deploy-i8h0dj_d/kernel/zImage tftp 0x10000000 14571401/tftp-deploy-i8h0dj_d/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '14571401/tftp-deploy-i8h0dj_d/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 14.3 MiB/s done Bytes transferred = 12554752 (bf9200 hex) => tftp 0x14000000 14571401/tftp-deploy-i8h0dj_d/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 14571401/tftp-deploy-i8h0dj_d/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '14571401/tftp-deploy-i8h0dj_d/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############### 14.3 MiB/s done Bytes transferred = 19290289 (12658b1 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 14571401/tftp-deploy-i8h0dj_d/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 14571401/tftp-deploy-i8h0dj_d/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '14571401/tftp-deploy-i8h0dj_d/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4.5 MiB/s done Bytes transferred = 42661 (a6a5 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0xbf9200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 19290225 Bytes = 18.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d6a4 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.218-cip49 (KernelCI@build-j244725-arm-gcc-10-multi-v7-defconfig-kselftest-8wnv6) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Jun 25 11:54:46 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 21 pages/cpu s55468 r8192 d22356 u86016 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 917616K/1048576K available (17408K kernel code, 2714K rwdata, 8152K rodata, 2048K init, 6693K bss, 65424K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] ftrace: allocating 56166 entries in 165 pages <6>[ 0.000000] ftrace: allocated 165 pages with 4 groups <6>[ 0.000000] Running RCU self tests <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU lockdep checking is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] Rude variant of Tasks RCU enabled. <6>[ 0.000000] Tracing variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000010] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008445] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022940] Console: colour dummy device 80x30 <4>[ 0.024842] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <4>[ 0.032854] ... MAX_LOCKDEP_SUBCLASSES: 8 <4>[ 0.037196] ... MAX_LOCK_DEPTH: 48 <4>[ 0.041611] ... MAX_LOCKDEP_KEYS: 8192 <4>[ 0.046245] ... CLASSHASH_SIZE: 4096 <4>[ 0.050831] ... MAX_LOCKDEP_ENTRIES: 32768 <4>[ 0.055552] ... MAX_LOCKDEP_CHAINS: 65536 <4>[ 0.060227] ... CHAINHASH_SIZE: 32768 <4>[ 0.064926] memory used by lock dependency info: 4061 kB <4>[ 0.070604] memory used for stack traces: 2112 kB <4>[ 0.075650] per task-struct memory footprint: 1536 bytes <6>[ 0.081340] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.091754] CPU: Testing write buffer coherency: ok <6>[ 0.096892] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.102164] pid_max: default: 32768 minimum: 301 <6>[ 0.107356] LSM: Security Framework initializing <6>[ 0.111982] LSM support for eBPF active <6>[ 0.116136] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.123583] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.135034] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.141581] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.147924] rcu: Hierarchical SRCU implementation. <6>[ 0.159241] EFI services will not be available. <6>[ 0.162307] smp: Bringing up secondary CPUs ... <6>[ 0.168829] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.168845] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.180612] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.180628] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.192026] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.192041] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.201078] smp: Brought up 1 node, 4 CPUs <6>[ 0.204790] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.211325] CPU: All CPU(s) started in SVC mode. <6>[ 0.218560] devtmpfs: initialized <6>[ 0.266893] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.274300] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.282246] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.293942] pinctrl core: initialized pinctrl subsystem <6>[ 0.302897] DMI not present or invalid. <6>[ 0.306351] NET: Registered protocol family 16 <6>[ 0.318411] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.331098] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.331596] cpuidle: using governor menu <6>[ 0.339701] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.976981] vdd1p1: supplied by regulator-dummy <6>[ 1.005917] vdd3p0: supplied by regulator-dummy <6>[ 1.034381] vdd2p5: supplied by regulator-dummy <6>[ 1.062908] vddarm: supplied by regulator-dummy <6>[ 1.092253] vddpu: supplied by regulator-dummy <6>[ 1.119966] vddsoc: supplied by regulator-dummy <6>[ 2.253692] No ATAGs? <6>[ 2.254505] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 2.261730] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 2.284556] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 2.313945] Serial: AMBA PL011 UART driver <6>[ 2.370315] Kprobes globally optimized <6>[ 2.473128] iommu: Default domain type: Translated <6>[ 2.477612] vgaarb: loaded <5>[ 2.482601] SCSI subsystem initialized <6>[ 2.486117] usbcore: registered new interface driver usbfs <6>[ 2.489754] usbcore: registered new interface driver hub <6>[ 2.495274] usbcore: registered new device driver usb <6>[ 2.507280] i2c i2c-0: IMX I2C adapter registered <6>[ 2.515296] i2c i2c-1: IMX I2C adapter registered <6>[ 2.521444] i2c i2c-2: IMX I2C adapter registered <6>[ 2.527694] pps_core: LinuxPPS API ver. 1 registered <6>[ 2.530089] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 2.539593] PTP clock support registered <6>[ 2.558403] clocksource: Switched to clocksource mxc_timer1 <6>[ 4.319133] NET: Registered protocol family 2 <6>[ 4.321589] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 4.331590] tcp_listen_portaddr_hash hash table entries: 512 (order: 2, 22528 bytes, linear) <6>[ 4.337603] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 4.345711] TCP bind hash table entries: 8192 (order: 6, 327680 bytes, linear) <6>[ 4.354416] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 4.360913] MPTCP token hash table entries: 1024 (order: 3, 49152 bytes, linear) <6>[ 4.367507] UDP hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.374385] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes, linear) <6>[ 4.382145] NET: Registered protocol family 1 <6>[ 4.388639] RPC: Registered named UNIX socket transport module. <6>[ 4.392201] RPC: Registered udp transport module. <6>[ 4.397150] RPC: Registered tcp transport module. <6>[ 4.402182] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 4.408896] NET: Registered protocol family 44 <6>[ 4.413535] PCI: CLS 0 bytes, default 64 <6>[ 4.419873] Trying to unpack rootfs image as initramfs... <6>[ 6.825144] Freeing initrd memory: 18840K <4>[ 6.827666] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 6.835304] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 6.850449] Initialise system trusted keyrings <6>[ 6.853359] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 6.901155] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.907571] NFS: Registering the id_resolver key type <5>[ 6.910270] Key type id_resolver registered <5>[ 6.914502] Key type id_legacy registered <6>[ 6.919330] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.925780] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.933585] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.939916] Key type asymmetric registered <5>[ 6.942414] Asymmetric key parser 'x509' registered <6>[ 6.947759] bounce: pool size: 64 pages <6>[ 6.951759] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.959322] io scheduler mq-deadline registered <6>[ 6.964001] io scheduler kyber registered <4>[ 6.969085] test_firmware: interface ready <6>[ 7.128620] mxs-dma 110000.dma-controller: initialized <4>[ 7.187758] imx-sdma 20ec000.dma-controller: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 7.195845] imx-sdma 20ec000.dma-controller: external firmware not found, using ROM firmware <6>[ 7.402997] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 7.424646] SuperH (H)SCI(F) driver initialized <6>[ 7.429305] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 7.440180] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 7.446627] printk: console [ttymxc1] enabled <6>[ 7.446627] printk: console [ttymxc1] enabled <6>[ 7.455521] printk: bootconsole [ec_imx21] disabled <6>[ 7.455521] printk: bootconsole [ec_imx21] disabled <6>[ 7.471516] msm_serial: driver initialized <6>[ 7.476817] STMicroelectronics ASC driver initialized <6>[ 7.488068] STM32 USART driver initialized <6>[ 7.512893] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 0 <4>[ 7.532816] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 7.541452] panel-simple panel-lcd: Specify missing connector_type <4>[ 7.549360] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.597975] brd: module loaded <6>[ 7.643100] loop: module loaded <6>[ 7.649382] lkdtm: No crash points registered, enable through debugfs <6>[ 7.669997] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 7.678218] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 7.686576] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 7.695100] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 7.703355] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 7.711747] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 7.719805] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 7.731270] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 7.738644] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 7.747728] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 7.761876] scsi host0: ahci-imx <6>[ 7.767419] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 7.825980] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 7.839312] pps pps0: new PPS source ptp0 <6>[ 7.898705] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 7.909190] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 7.914449] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 7.920920] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 7.926608] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 7.952188] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 7.960064] usbcore: registered new interface driver pegasus <6>[ 7.966199] usbcore: registered new interface driver asix <6>[ 7.972066] usbcore: registered new interface driver ax88179_178a <6>[ 7.978639] usbcore: registered new interface driver cdc_ether <6>[ 7.984950] usbcore: registered new interface driver smsc75xx <6>[ 7.991213] usbcore: registered new interface driver smsc95xx <6>[ 7.997377] usbcore: registered new interface driver net1080 <6>[ 8.003526] usbcore: registered new interface driver cdc_subset <6>[ 8.009908] usbcore: registered new interface driver zaurus <6>[ 8.016008] usbcore: registered new interface driver cdc_ncm <6>[ 8.033516] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 8.040447] ehci-pci: EHCI PCI platform driver <6>[ 8.045322] ehci-platform: EHCI generic platform driver <6>[ 8.051810] ehci-orion: EHCI orion driver <6>[ 8.056919] SPEAr-ehci: EHCI SPEAr driver <6>[ 8.062045] ehci-st: EHCI STMicroelectronics driver <6>[ 8.067970] ehci-exynos: EHCI Exynos driver <6>[ 8.073239] ehci-atmel: EHCI Atmel driver <6>[ 8.078279] tegra-ehci: Tegra EHCI driver <6>[ 8.083410] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 8.089988] ohci-pci: OHCI PCI platform driver <6>[ 8.094885] ohci-platform: OHCI generic platform driver <6>[ 8.101045] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 8.101308] SPEAr-ohci: OHCI SPEAr driver <6>[ 8.107074] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 8.111946] ohci-st: OHCI STMicroelectronics driver <6>[ 8.117734] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 8.123699] ohci-atmel: OHCI Atmel driver <6>[ 8.138716] usbcore: registered new interface driver usb-storage <6>[ 8.174065] i2c /dev entries driver <6>[ 8.250796] sdhci: Secure Digital Host Controller Interface driver <6>[ 8.257273] sdhci: Copyright(c) Pierre Ossman <6>[ 8.270637] Synopsys Designware Multimedia Card Interface Driver <6>[ 8.283545] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 8.293130] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 8.298667] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 8.300007] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 8.310465] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 8.320309] usbcore: registered new interface driver usbhid <6>[ 8.326175] usbhid: USB HID core driver <6>[ 8.342392] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 8.344460] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 8.352481] ipip: IPv4 and MPLS over IPv4 tunneling driver <6>[ 8.364875] IPv4 over IPsec tunneling driver <6>[ 8.373861] NET: Registered protocol family 10 <6>[ 8.383921] Segment Routing with IPv6 <6>[ 8.392201] mmc2: new high speed SDHC card at address aaaa <6>[ 8.393555] NET: Registered protocol family 17 <6>[ 8.401845] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <6>[ 8.404435] 8021q: 802.1Q VLAN Support v1.8 <5>[ 8.413171] Key type dns_resolver registered <4>[ 8.425241] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 8.431404] ThumbEE CPU extension supported. <4>[ 8.433106] GPT:29296874 != 31116287 <5>[ 8.437594] Registering SWP/SWPB emulation handler <4>[ 8.441453] GPT:Alternate GPT header not at the end of the disk. <4>[ 8.441470] GPT:29296874 != 31116287 <4>[ 8.441483] GPT: Use GNU Parted to correct GPT errors. <6>[ 8.441563] mmcblk2: p1 p2 p3 <5>[ 8.447864] Loading compiled-in X.509 certificates <4>[ 8.624486] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.633103] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.645703] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.679497] imx_usb 2184200.usb: No over current polarity defined <6>[ 8.692236] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 8.697714] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 8.728936] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 8.747697] hub 1-0:1.0: USB hub found <6>[ 8.752308] hub 1-0:1.0: 1 port detected <6>[ 8.767119] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 8.797298] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.805766] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.818605] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.846702] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.855224] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.867772] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.885811] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 8.914258] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.922749] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.935480] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.956417] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 9.138820] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 9.346906] hub 1-1:1.0: USB hub found <6>[ 9.352752] hub 1-1:1.0: 3 ports detected <4>[ 9.382444] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.391098] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.405337] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 12.080301] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 12.089802] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 12.118411] Sending DHCP requests ., OK <6>[ 12.163033] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 12.171605] IP-Config: Complete: <6>[ 12.175170] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 12.186009] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 12.194263] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 12.194302] nameserver0=192.168.201.1 <6>[ 12.207889] clk: Disabling unused clocks <6>[ 12.262963] Freeing unused kernel memory: 2048K <6>[ 12.269326] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 12.655948] udevd[144]: starting version 3.2.9 <5>[ 12.664418] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.672184] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 12.679117] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 12.698510] udevd[144]: specified user 'tss' unknown <27>[ 12.704077] udevd[144]: specified group 'tss' unknown <30>[ 12.717374] udevd[145]: starting eudev-3.2.9 <6>[ 13.949486] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 13.965904] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 14.015717] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.078977] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.091893] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 14.176476] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 14.195147] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.204253] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.213280] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.222259] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.248779] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.264357] caam 2100000.crypto: Entropy delay = 3200 <4>[ 14.304516] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.330551] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 14.364546] CAN device driver interface <4>[ 14.374260] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.383330] panel-simple panel-lcd: Specify missing connector_type <6>[ 14.391308] caam 2100000.crypto: Instantiated RNG4 SH1 <4>[ 14.396132] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 14.396751] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 14.411654] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 14.570533] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.598781] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.618745] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 14.625594] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 14.679486] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 14.701840] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 14.708245] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 14.748598] [drm] Initialized etnaviv 1.4.0 20151214 for etnaviv on minor 1 <6>[ 14.849068] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.857832] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.866688] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 14.875423] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 14.938803] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 14.947302] panel-simple panel-lcd: Specify missing connector_type <4>[ 14.995136] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.104716] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.113479] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.122296] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.131000] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.175631] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 15.185192] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 15.196602] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.205285] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.218915] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.262296] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 15.262520] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.276290] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.281402] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 15.285060] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.301321] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.325329] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.333891] panel-simple panel-lcd: Specify missing connector_type <4>[ 15.361812] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 15.391262] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.400047] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.409072] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 15.417783] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 15.448509] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 15.457079] panel-simple panel-lcd: Specify missing connector_type <6>[ 15.932906] caam algorithms registered in /proc/crypto <6>[ 15.965280] caam 2100000.crypto: registering rng-caam <4>[ 15.981762] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 16.019368] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.028027] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.036911] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.045568] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <4>[ 16.074861] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 16.083472] panel-simple panel-lcd: Specify missing connector_type done <4>[ 16.097969] panel-simple panel-lvds0: supply power not found, using dummy regulator Saving random seed: <6>[ 16.129592] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.138457] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops ipu_crtc_ops [imxdrm]) <6>[ 16.147173] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops ipu_crtc_ops [imxdrm]) <5>[ 16.153231] random: dd: uninitialized urandom read (32 bytes read) <6>[ 16.156048] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops ipu_crtc_ops [imxdrm]) <5>[ 16.156106] random: crng init done <5>[ 16.156119] random: 1 urandom warning(s) missed due to ratelimiting OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-14571401/environment . /lava-14571401/environment / # /lava-14571401/bin/lava-test-runner /lava-14571401/0 /lava-14571401/bin/lava-test-runner /lava-14571401/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-14571401/0/tests/0_dmesg + cat uuid + UUID=14571401_1.5.2.4.1<8>[ 17.253229] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 17.381717] <8>[ 17.499180] <8>[ 17.612843] + set +x <8>[ 17.624587] / #