Trying 127.0.0.1...
Connected to 127.0.0.1.
Escape character is '^]'.
[    0.000144] NOTICE:  BL2: RZ G2N Initial Program Loader(CA57)
[    0.004408] NOTICE:  BL2: Initial Program Loader(Rev.2.0.4)
[    0.009941] NOTICE:  BL2: PRR is RZG G2N Ver.1.1
[    0.014523] NOTICE:  BL2: Board is HiHope RZ/G2N Rev.1.0
[    0.019788] NOTICE:  BL2: Boot device is QSPI Flash(40MHz)
[    0.025228] NOTICE:  BL2: LCM state is CM
[    0.029209] NOTICE:  BL2: DDR3200(rev.0.37)
[    0.036159] NOTICE:  BL2: [COLD_BOOT]
[    0.040791] NOTICE:  BL2: DRAM Split is OFF
[    0.043486] NOTICE:  BL2: QoS is default setting(rev.0.09)
[    0.048929] NOTICE:  BL2: DRAM refresh interval 1.95 usec
[    0.054286] NOTICE:  BL2: Periodic Write DQ Training
[    0.059313] NOTICE:  BL2: Lossy Decomp areas
[    0.063444] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.070529] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.077441] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.084356] NOTICE:  BL2: v1.5(release):236f8fb-dirty
[    0.089364] NOTICE:  BL2: Built : 08:01:16, Oct 21 2019
[    0.094552] NOTICE:  BL2: Normal boot
[    0.098191] NOTICE:  BL2: dst=0xe6320100 src=0x8180000 len=512(0x200)
[    0.104680] NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
[    0.112408] NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
[    0.131319] NOTICE:  BL2: dst=0x50000000 src=0x8300000 len=1048576(0x100000)
[    0.351568] NOTICE:  BL2: Booting BL31


U-Boot 2018.09 (Oct 21 2019 - 05:40:53 +0000)

CPU: Renesas Electronics R8A774B1 rev 1.1
Model: Hoperun Technology HiHope RZ/G2N platform (hihope-rzg2n)
DRAM:  3.9 GiB
Bank #0: 0x048000000 - 0x0bfffffff, 1.9 GiB
Bank #1: 0x480000000 - 0x4ffffffff, 2 GiB

Error reading output register
Error reading output register
Error reading output register
Error reading output register
MMC:   sd@ee100000: 0, sd@ee160000: 1
Loading Environment from MMC... OK
In:    serial@e6e88000
Out:   serial@e6e88000
Err:   serial@e6e88000
Net:   eth0: ethernet@e6800000
Hit any key to stop autoboot:  2 
 0 
=> setenv autoload no
setenv autoload no
=> setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
=> setenv fdt_high 0xffffffff
setenv fdt_high 0xffffffff
=> dhcp
dhcp
ethernet@e6800000 Waiting for PHY auto negotiation to complete....