Trying 127.0.0.1...
Connected to 127.0.0.1.
Escape character is '^]'.
RomBOOT


AT91Bootstrap 3.7.2-rc2-dirty (Tue 14 Apr 02:17:07 BST 2015)

NAND: ONFI not supported
NAND: Manufacturer ID: 0xec Chip ID: 0xda
NAND: Disable On-Die ECC
NAND: Press the recovery button (BP4) to recovery
NAND: Using Software ECC
NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x21f00000
NAND: Done to load image


U-Boot 2015.01 (Apr 14 2015 - 16:45:04)

CPU: AT91SAM9G20
Crystal frequency:   18.432 MHz
CPU clock        :  396.288 MHz
Master clock     :  132.096 MHz
DRAM:  64 MiB
WARNING: Caches not enabled
NAND:  256 MiB
MMC:   mci: 0
In:    serial
Out:   serial
Err:   serial
Net:   macb0
Hit any key to stop autoboot:  3 
 0 
U-Boot> setenv autoload no
setenv autoload no
U-Boot> setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
U-Boot> setenv fdt_high 0xffffffff
setenv fdt_high 0xffffffff
U-Boot> dhcp
dhcp
macb0: Starting autonegotiation...
macb0: Autonegotiation complete
macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1)
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
*** Unhandled DHCP Option in OFFER/ACK: 42
*** Unhandled DHCP Option in OFFER/ACK: 42
DHCP client bound to address 192.168.56.25 (3800 ms)
U-Boot> setenv serverip 192.168.56.230
setenv serverip 192.168.56.230
U-Boot> tftp 0x22100000 354396/tftp-deploy-abrsolod/kernel/zImage
tftp 0x22100000 354396/tftp-deploy-abrsolod/kernel/zImage
macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1)
Using macb0 device
TFTP from server 192.168.56.230; our IP address is 192.168.56.25
Filename '354396/tftp-deploy-abrsolod/kernel/zImage'.
Load address: 0x22100000
Loading: *#################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 ###
	 1.2 MiB/s
done
Bytes transferred = 4805488 (495370 hex)
U-Boot> tftp 0x23000000 354396/tftp-deploy-abrsolod/ramdisk/ramdisk.cpio.gz.uboot
tftp 0x23000000 354396/tftp-deploy-abrsolod/ramdisk/ramdisk.cpio.gz.uboot
macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1)
Using macb0 device
TFTP from server 192.168.56.230; our IP address is 192.168.56.25
Filename '354396/tftp-deploy-abrsolod/ramdisk/ramdisk.cpio.gz.uboot'.
Load address: 0x23000000
Loading: *#################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 ##################################################
	 1.2 MiB/s
done
Bytes transferred = 9307213 (8e044d hex)
U-Boot> setenv initrd_size ${filesize}
setenv initrd_size ${filesize}
U-Boot> tftp 0x22000000 354396/tftp-deploy-abrsolod/dtb/at91sam9g20ek.dtb
tftp 0x22000000 354396/tftp-deploy-abrsolod/dtb/at91sam9g20ek.dtb
macb0: link up, 100Mbps full-duplex (lpa: 0xc1e1)
Using macb0 device
TFTP from server 192.168.56.230; our IP address is 192.168.56.25
Filename '354396/tftp-deploy-abrsolod/dtb/at91sam9g20ek.dtb'.
Load address: 0x22000000
Loading: *##
	 1.1 MiB/s
done
Bytes transferred = 16715 (414b hex)
U-Boot> setenv bootargs ' root=/dev/ram0 cma=0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp'
setenv bootargs ' root=/dev/ram0 cma=0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp'
U-Boot> bootz 0x22100000 0x23000000 0x22000000
bootz 0x22100000 0x23000000 0x22000000
Kernel image @ 0x22100000 [ 0x000000 - 0x495370 ]
## Loading init Ramdisk from Legacy Image at 23000000 ...
   Image Name:   
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    9307149 Bytes = 8.9 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 22000000
   Booting using the fdt blob at 0x22000000
   Using Device Tree in place at 22000000, end 2200714a

Starting kernel ...

<6>Booting Linux on physical CPU 0x0
<5>Linux version 5.10.218-cip49 (KernelCI@build-j219016-arm-gcc-10-at91-dt-defconfig-frzx4) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 Thu Jun 6 00:13:15 UTC 2024
<6>CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
<6>CPU: VIVT data cache, VIVT instruction cache
<6>OF: fdt: Machine model: Atmel at91sam9g20ek
<6>Memory policy: Data cache writeback
<6>Zone ranges:
<6>  Normal   [mem 0x0000000020000000-0x0000000023ffffff]
<6>Movable zone start for each node
<6>Early memory node ranges
<6>  node   0: [mem 0x0000000020000000-0x0000000023ffffff]
<6>Initmem setup node 0 [mem 0x0000000020000000-0x0000000023ffffff]
<6>Built 1 zonelists, mobility grouping on.  Total pages: 16256
<5>Kernel command line: root=/dev/ram0 cma=0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp
<6>Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear)
<6>Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear)
<6>mem auto-init: stack:off, heap alloc:off, heap free:off
<6>Memory: 45928K/65536K available (6438K kernel code, 236K rwdata, 2524K rodata, 260K init, 144K bss, 19608K reserved, 0K cma-reserved)
<6>NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
<6>clocksource: timer@fffa0000: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 115749784805 ns
<6>sched_clock: 32 bits at 16MHz, resolution 60ns, wraps every 130055938017ns
<6>Switching to timer-based delay loop, resolution 60ns
<6>Console: colour dummy device 80x30
<6>printk: console [tty0] enabled
<6>Calibrating delay loop (skipped), value calculated using timer frequency.. 33.07 BogoMIPS (lpj=129000)
<6>CPU: Testing write buffer coherency: ok
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
<6>Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
<6>Setting up static identity map for 0x20008400 - 0x2000847c
<6>devtmpfs: initialized
<6>clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 14931722236523437 ns
<6>futex hash table entries: 256 (order: -1, 3072 bytes, linear)
<6>pinctrl core: initialized pinctrl subsystem
<6>NET: Registered protocol family 16
<6>DMA: preallocated 256 KiB pool for atomic coherent allocations
<6>AT91: PM: standby: standby, suspend: ulp0
<6>No ATAGs?
<6>gpio-at91 fffff400.gpio: at address (ptrval)
<6>gpio-at91 fffff600.gpio: at address (ptrval)
<6>gpio-at91 fffff800.gpio: at address (ptrval)
<6>pinctrl-at91 ahb:apb:pinctrl@fffff400: initialized AT91 pinctrl driver
<4>atmel_tcb: probe of fffa0000.timer failed with error -16
<6>AT91: Detected SoC: at91sam9g20, revision 1
<5>SCSI subsystem initialized
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>i2c-gpio i2c-gpio-0: using lines 23 (SDA) and 24 (SCL)
<6>mc: Linux media interface: v0.10
<6>videodev: Linux video capture interface: v2.00
<6>Advanced Linux Sound Architecture Driver Initialized.
<6>clocksource: Switched to clocksource timer@fffa0000
<6>NET: Registered protocol family 2
<6>IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear)
<6>tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
<6>TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear)
<6>TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear)
<6>TCP: Hash tables configured (established 1024 bind 1024)
<6>UDP hash table entries: 256 (order: 0, 4096 bytes, linear)
<6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear)
<6>NET: Registered protocol family 1
<6>RPC: Registered named UNIX socket transport module.
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>Trying to unpack rootfs image as initramfs...
<6>Freeing initrd memory: 9092K
<5>Initialise system trusted keyrings
<6>workingset: timestamp_bits=30 max_order=14 bucket_order=0
<5>Key type asymmetric registered
<5>Asymmetric key parser 'x509' registered
<6>io scheduler mq-deadline registered
<6>io scheduler kyber registered
<6>brd: module loaded
<6>loop: module loaded
<6>ssc fffbc000.ssc: Atmel SSC device at 0x(ptrval) (irq 31)
<4>atmel_usart_serial: Failed to locate of_node [id: -2]
<6>atmel_usart_serial.0.auto: ttyS0 at MMIO 0xfffff200 (irq = 17, base_baud = 8256000) is a ATMEL_SERIAL
<6>printk: console [ttyS0] enabled
<4>atmel_usart_serial: Failed to locate of_node [id: -2]
<6>atmel_usart_serial.1.auto: ttyS1 at MMIO 0xfffb0000 (irq = 26, base_baud = 8256000) is a ATMEL_SERIAL
<4>atmel_usart_serial: Failed to locate of_node [id: -2]
<6>atmel_usart_serial.2.auto: ttyS2 at MMIO 0xfffb4000 (irq = 27, base_baud = 8256000) is a ATMEL_SERIAL
<6>macb fffc4000.ethernet eth0: Cadence MACB rev 0x0001010c at 0xfffc4000 irq 28 (a6:72:4e:7e:7a:f8)
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ehci-atmel: EHCI Atmel driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<6>ohci-atmel: OHCI Atmel driver
<6>at91_ohci 500000.ohci: USB Host Controller
<6>at91_ohci 500000.ohci: new USB bus registered, assigned bus number 1
<6>at91_ohci 500000.ohci: irq 33, io mem 0x00500000
<6>usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
<6>usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>usb usb1: Product: USB Host Controller
<6>usb usb1: Manufacturer: Linux 5.10.218-cip49 ohci_hcd
<6>usb usb1: SerialNumber: at91
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>usbcore: registered new interface driver cdc_acm
<6>cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
<6>usbcore: registered new interface driver usb-storage
<6>usbcore: registered new interface driver usbserial_generic
<6>usbserial: USB Serial support registered for generic
<6>usbcore: registered new interface driver ftdi_sio
<6>usbserial: USB Serial support registered for FTDI USB Serial Device
<6>usbcore: registered new interface driver pl2303
<6>usbserial: USB Serial support registered for pl2303
<6>udc: at91_udc version 3 May 2006
<6>g_serial gadget: Gadget Serial v2.4
<6>g_serial gadget: g_serial ready
<4>rtc-at91sam9 fffffd20.rtc: rtc0: SET TIME!
<6>rtc-at91sam9 fffffd20.rtc: registered as rtc0
<3>rtc-at91sam9 fffffd20.rtc: hctosys: unable to read the hardware clock
<6>at91-reset fffffd00.rstc: Starting after general reset
<3>at91_wdt fffffd40.watchdog: watchdog is disabled
<4>at91_wdt: probe of fffffd40.watchdog failed with error -22
<6>sdhci: Secure Digital Host Controller Interface driver
<6>sdhci: Copyright(c) Pierre Ossman
<6>sdhci-pltfm: SDHCI platform and OF driver helper
<6>usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
<6>nand: device found, Manufacturer ID: 0xec, Chip ID: 0xda
<6>nand: Samsung NAND 256MiB 3,3V 8-bit
<6>nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
<6>atmel_mci fffa8000.mmc: version: 0x210
<6>atmel_mci fffa8000.mmc: using PDC
<6>Bad block table found at page 131008, version 0x01
<6>Bad block table found at page 130944, version 0x01
<6>nand_read_bbt: bad block at 0x000006120000
<6>nand_read_bbt: bad block at 0x00000d880000
<5>8 fixed-partitions partitions found on MTD device atmel_nand
<5>Creating 8 MTD partitions on "atmel_nand":
<5>0x000000000000-0x000000020000 : "at91bootstrap"
<6>atmel_mci fffa8000.mmc: Atmel MCI controller at 0xfffa8000 irq 30, 1 slots
<5>0x000000020000-0x000000060000 : "barebox"
<5>0x000000060000-0x000000080000 : "bareboxenv"
<5>0x000000080000-0x0000000a0000 : "bareboxenv2"
<5>0x0000000a0000-0x0000000c0000 : "oftree"
<5>0x0000000c0000-0x0000004c0000 : "kernel"
<5>0x0000004c0000-0x000007cc0000 : "rootfs"
<5>0x000007cc0000-0x000010000000 : "data"
<6>iio iio:device0: Resolution used: 10 bits
<6>iio iio:device0: not support touchscreen in the adc compatible string.
<4>wm8731 1-001b: supply AVDD not found, using dummy regulator
<4>wm8731 1-001b: supply HPVDD not found, using dummy regulator
<4>wm8731 1-001b: supply DCVDD not found, using dummy regulator
<4>wm8731 1-001b: supply DBVDD not found, using dummy regulator
<3>at91sam9g20ek-audio sound: Failed to get MCLK
<4>at91sam9g20ek-audio: probe of sound failed with error -2
<6>NET: Registered protocol family 10
<6>Segment Routing with IPv6
<6>sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
<6>NET: Registered protocol family 17
<5>Loading compiled-in X.509 certificates
<6>input: gpio_keys as /devices/platform/gpio_keys/input/input0
<6>macb fffc4000.ethernet eth0: PHY [fffc4000.ethernet-ffffffff:00] driver [Davicom DM9161A] (irq=POLL)
<6>macb fffc4000.ethernet eth0: configuring for phy/rmii link mode
<6>Waiting up to 100 more seconds for network.
<6>Waiting up to 80 more seconds for network.
<6>Waiting up to 60 more seconds for network.
<6>Waiting up to 40 more seconds for network.
<6>Waiting up to 20 more seconds for network.
#
<5>Sending DHCP requests ..
<5>random: crng init done
#
#
#
<4>.... timed out!
<3>IP-Config: Reopening network devices...
<6>macb fffc4000.ethernet eth0: PHY [fffc4000.ethernet-ffffffff:00] driver [Davicom DM9161A] (irq=POLL)
<6>macb fffc4000.ethernet eth0: configuring for phy/rmii link mode
#
<6>Waiting up to 100 more seconds for network.