[Enter `^Ec?' for help] U-Boot SPL 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45) U-Boot 2015.10-00025-g943d444 (Feb 19 2016 - 15:04:45 +0000) Model: Radxa Rock 2 Square DRAM: 2 GiB MMC: dwmmc@ff0c0000: 0, dwmmc@ff0f0000: 1 In: serial@ff690000 Out: serial@ff690000 Err: serial@ff690000 Incorrect eeprom header Net: eth0: ethernet@ff290000 Hit any key to stop autoboot: 1  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp ethernet@ff290000 Waiting for PHY auto negotiation to complete...... done Speed: 1000, full duplex BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 192.168.201.22 (762 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x2000000 14191865/tftp-deploy-8__na0g4/kernel/zImage tftp 0x2000000 14191865/tftp-deploy-8__na0g4/kernel/zImage Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '14191865/tftp-deploy-8__na0g4/kernel/zImage'. Load address: 0x2000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############# 3.5 MiB/s done Bytes transferred = 9720320 (945200 hex) => tftp 0x4000000 14191865/tftp-deploy-8__na0g4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x4000000 14191865/tftp-deploy-8__na0g4/ramdisk/ramdisk.cpio.gz.uboot Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '14191865/tftp-deploy-8__na0g4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x4000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################################## 3.6 MiB/s done Bytes transferred = 16106259 (f5c313 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x1f00000 14191865/tftp-deploy-8__na0g4/dtb/rk3288-rock2-square.dtb tftp 0x1f00000 14191865/tftp-deploy-8__na0g4/dtb/rk3288-rock2-square.dtb Speed: 1000, full duplex Using ethernet@ff290000 device TFTP from server 192.168.201.1; our IP address is 192.168.201.22 Filename '14191865/tftp-deploy-8__na0g4/dtb/rk3288-rock2-square.dtb'. Load address: 0x1f00000 Loading: *### 3.3 MiB/s done Bytes transferred = 41652 (a2b4 hex) => setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x2000000 0x4000000 0x1f00000 bootz 0x2000000 0x4000000 0x1f00000 Kernel image @ 0x2000000 [ 0x000000 - 0x945200 ] ## Loading init Ramdisk from Legacy Image at 04000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16106195 Bytes = 15.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 01f00000 Booting using the fdt blob at 0x1f00000 Using Device Tree in place at 01f00000, end 01f0d2b3 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x500 [ 0.000000] Linux version 5.10.218-cip49 (KernelCI@build-j219060-arm-gcc-10-multi-v7-defconfig-kfd9h) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Thu Jun 6 00:18:28 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [410fc0d1] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Radxa Rock 2 Square [ 0.000000] earlycon: uart0 at MMIO32 0xff690000 (options '115200n8') [ 0.000000] printk: bootconsole [uart0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x7c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522752 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1972996K/2097152K available (14336K kernel code, 2240K rwdata, 5368K rodata, 2048K init, 428K bss, 58620K reserved, 65536K cma-reserved, 1245184K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.009083] Switching to timer-based delay loop, resolution 41ns <6>[ 0.022662] Console: colour dummy device 80x30 <6>[ 0.027869] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.039537] CPU: Testing write buffer coherency: ok <6>[ 0.045209] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.051049] pid_max: default: 32768 minimum: 301 <6>[ 0.056540] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.064873] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.074576] CPU0: thread -1, cpu 0, socket 5, mpidr 80000500 <6>[ 0.081994] Setting up static identity map for 0x300000 - 0x3000ac <6>[ 0.091040] rcu: Hierarchical SRCU implementation. <6>[ 0.101309] EFI services will not be available. <6>[ 0.106878] smp: Bringing up secondary CPUs ... <6>[ 0.113904] CPU1: thread -1, cpu 1, socket 5, mpidr 80000501 <6>[ 0.113913] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.128193] CPU2: thread -1, cpu 2, socket 5, mpidr 80000502 <6>[ 0.128202] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.142421] CPU3: thread -1, cpu 3, socket 5, mpidr 80000503 <6>[ 0.142430] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.154902] smp: Brought up 1 node, 4 CPUs <6>[ 0.159714] SMP: Total of 4 processors activated (192.00 BogoMIPS). <6>[ 0.166876] CPU: All CPU(s) started in SVC mode. <6>[ 0.172867] devtmpfs: initialized <6>[ 0.186018] VFP support v0.3: implementor 41 architecture 3 part 30 variant d rev 0 <6>[ 0.194958] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.206068] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.215727] pinctrl core: initialized pinctrl subsystem <6>[ 0.223760] DMI not present or invalid. <6>[ 0.229108] NET: Registered protocol family 16 <6>[ 0.236666] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.247146] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.247686] cpuidle: using governor menu <6>[ 0.259744] No ATAGs? <6>[ 0.262670] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.271769] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.281829] Serial: AMBA PL011 UART driver <6>[ 0.385553] iommu: Default domain type: Translated <6>[ 0.392780] vgaarb: loaded <5>[ 0.397040] SCSI subsystem initialized <6>[ 0.401898] usbcore: registered new interface driver usbfs <6>[ 0.408279] usbcore: registered new interface driver hub <6>[ 0.414436] usbcore: registered new device driver usb <6>[ 0.422232] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.427968] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.438310] PTP clock support registered <6>[ 0.446291] clocksource: Switched to clocksource arch_sys_counter <6>[ 1.810230] NET: Registered protocol family 2 <6>[ 1.815535] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.825364] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.834882] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.843762] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.852097] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.859464] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.867077] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.875285] NET: Registered protocol family 1 <6>[ 1.880958] RPC: Registered named UNIX socket transport module. <6>[ 1.887788] RPC: Registered udp transport module. <6>[ 1.893236] RPC: Registered tcp transport module. <6>[ 1.898717] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 1.906083] PCI: CLS 0 bytes, default 64 <6>[ 1.911129] Trying to unpack rootfs image as initramfs... <6>[ 3.462501] Freeing initrd memory: 15732K <6>[ 3.467932] hw perfevents: enabled with armv7_cortex_a12 PMU driver, 7 counters available <5>[ 3.478772] Initialise system trusted keyrings <6>[ 3.484161] workingset: timestamp_bits=30 max_order=19 bucket_order=0 <6>[ 3.498461] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.505909] NFS: Registering the id_resolver key type <5>[ 3.511826] Key type id_resolver registered <5>[ 3.516737] Key type id_legacy registered <6>[ 3.521540] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.529204] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.537656] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.543215] Key type asymmetric registered <5>[ 3.548029] Asymmetric key parser 'x509' registered <6>[ 3.553721] bounce: pool size: 64 pages <6>[ 3.558265] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.566691] io scheduler mq-deadline registered <6>[ 3.571948] io scheduler kyber registered <6>[ 3.616226] dma-pl330 ff250000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 3.624864] dma-pl330 ff250000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 <6>[ 3.636090] dma-pl330 ffb20000.dma-controller: Loaded driver for PL330 DMAC-241330 <6>[ 3.644721] dma-pl330 ffb20000.dma-controller: DBUFF-64x8bytes Num_Chans-5 Num_Peri-6 Num_Events-10 <6>[ 3.727858] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.738214] printk: console [ttyS2] disabled <6>[ 3.743263] ff690000.serial: ttyS2 at MMIO 0xff690000 (irq = 43, base_baud = 1500000) is a 16550A <6>[ 3.753476] printk: console [ttyS2] enabled <6>[ 3.753476] printk: console [ttyS2] enabled <6>[ 3.763444] printk: bootconsole [uart0] disabled <6>[ 3.763444] printk: bootconsole [uart0] disabled <6>[ 3.777174] SuperH (H)SCI(F) driver initialized <6>[ 3.783972] msm_serial: driver initialized <6>[ 3.789122] STMicroelectronics ASC driver initialized <6>[ 3.796959] STM32 USART driver initialized <6>[ 3.820867] brd: module loaded <6>[ 3.831388] loop: module loaded <6>[ 3.850875] CAN device driver interface <6>[ 3.856803] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.865025] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.870894] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.877887] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.884215] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.894323] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 3.901655] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 3.912083] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.920737] usbcore: registered new interface driver pegasus <6>[ 3.927448] usbcore: registered new interface driver asix <6>[ 3.933820] usbcore: registered new interface driver ax88179_178a <6>[ 3.940993] usbcore: registered new interface driver cdc_ether <6>[ 3.947873] usbcore: registered new interface driver smsc75xx <6>[ 3.954637] usbcore: registered new interface driver smsc95xx <6>[ 3.961415] usbcore: registered new interface driver net1080 <6>[ 3.968085] usbcore: registered new interface driver cdc_subset <6>[ 3.975040] usbcore: registered new interface driver zaurus <6>[ 3.981675] usbcore: registered new interface driver cdc_ncm <4>[ 3.991300] dwc2 ff540000.usb: supply vusb_d not found, using dummy regulator <4>[ 3.999746] dwc2 ff540000.usb: supply vusb_a not found, using dummy regulator <6>[ 4.076592] dwc2 ff540000.usb: DWC OTG Controller <6>[ 4.082171] dwc2 ff540000.usb: new USB bus registered, assigned bus number 1 <6>[ 4.090408] dwc2 ff540000.usb: irq 48, io mem 0xff540000 <6>[ 4.097442] hub 1-0:1.0: USB hub found <6>[ 4.101972] hub 1-0:1.0: 1 port detected <4>[ 4.107485] dwc2 ff580000.usb: supply vusb_d not found, using dummy regulator <4>[ 4.115909] dwc2 ff580000.usb: supply vusb_a not found, using dummy regulator <6>[ 4.266327] dwc2 ff580000.usb: EPs: 10, dedicated fifos, 972 entries in SPRAM <6>[ 4.274867] dwc2 ff580000.usb: DWC OTG Controller <6>[ 4.280470] dwc2 ff580000.usb: new USB bus registered, assigned bus number 2 <6>[ 4.288694] dwc2 ff580000.usb: irq 49, io mem 0xff580000 <6>[ 4.295682] hub 2-0:1.0: USB hub found <6>[ 4.300243] hub 2-0:1.0: 1 port detected <6>[ 4.306539] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.314135] ehci-pci: EHCI PCI platform driver <6>[ 4.319469] ehci-platform: EHCI generic platform driver <6>[ 4.325940] ehci-platform ff500000.usb: EHCI Host Controller <6>[ 4.332606] ehci-platform ff500000.usb: new USB bus registered, assigned bus number 3 <6>[ 4.341938] ehci-platform ff500000.usb: irq 47, io mem 0xff500000 <6>[ 4.376286] ehci-platform ff500000.usb: USB 2.0 started, EHCI 1.00 <6>[ 4.384258] hub 3-0:1.0: USB hub found <6>[ 4.388816] hub 3-0:1.0: 1 port detected <6>[ 4.394191] ehci-orion: EHCI orion driver <6>[ 4.399233] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.404202] ehci-st: EHCI STMicroelectronics driver <6>[ 4.410171] ehci-exynos: EHCI Exynos driver <6>[ 4.415326] ehci-atmel: EHCI Atmel driver <6>[ 4.420316] tegra-ehci: Tegra EHCI driver <6>[ 4.425311] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.432560] ohci-pci: OHCI PCI platform driver <6>[ 4.437895] ohci-platform: OHCI generic platform driver <6>[ 4.444300] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.449295] ohci-st: OHCI STMicroelectronics driver <6>[ 4.455229] ohci-atmel: OHCI Atmel driver <6>[ 4.461355] usbcore: registered new interface driver usb-storage <6>[ 4.475900] i2c /dev entries driver <6>[ 4.486346] VCC_DDR: supplied by vcc_sys <6>[ 4.493345] VCC_IO: supplied by vcc_sys <6>[ 4.500245] VDD_LOG: Bringing 1100000uV into 1000000-1000000uV <6>[ 4.509472] VDD_LOG: supplied by vcc_sys <6>[ 4.516424] VCC_20: supplied by vcc_sys <6>[ 4.523305] VCCIO_SD: supplied by VCC_IO <6>[ 4.530809] VDD10_LCD: supplied by VCC_IO <6>[ 4.538772] VCCA_CODEC: supplied by VCC_IO <6>[ 4.546842] VCCA_TP: supplied by vcc_sys <6>[ 4.554211] VCCIO_PMU: supplied by vcc_sys <6>[ 4.561415] VDD_10: supplied by VCC_20 <6>[ 4.568706] VCC_18: supplied by VCC_20 <6>[ 4.576010] VCC18_LCD: supplied by VCC_20 <6>[ 4.585109] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! <6>[ 4.594515] vdd_cpu: supplied by vcc_sys <6>[ 4.601853] vcc_flash: supplied by VCC_IO <6>[ 4.607220] vcc_sd: supplied by VCC_IO <6>[ 4.614029] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! <6>[ 4.623442] vdd_gpu: supplied by vcc_sys <4>[ 4.646396] dw_wdt ff800000.watchdog: No valid TOPs array specified <6>[ 4.662976] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 500000 KHz, changing to: 600000 KHz <6>[ 4.677456] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.684654] sdhci: Copyright(c) Pierre Ossman <6>[ 4.690637] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.698304] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.698306] dwmmc_rockchip ff0c0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.698334] dwmmc_rockchip ff0c0000.mmc: Using internal DMA controller. <6>[ 4.698430] dwmmc_rockchip ff0f0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.698448] dwmmc_rockchip ff0f0000.mmc: Using internal DMA controller. <6>[ 4.698454] dwmmc_rockchip ff0f0000.mmc: Version ID is 270a <6>[ 4.698475] dwmmc_rockchip ff0f0000.mmc: DW MMC controller at irq 40,32 bit host data width,256 deep fifo <6>[ 4.699120] dwmmc_rockchip ff0f0000.mmc: allocated mmc-pwrseq <6>[ 4.699123] mmc_host mmc0: card is non-removable. <6>[ 4.712197] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 4.713096] dwmmc_rockchip ff0c0000.mmc: Version ID is 270a <6>[ 4.720784] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 4.728952] dwmmc_rockchip ff0c0000.mmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo <6>[ 4.736635] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 4.743241] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.743244] usb 3-1: new high-speed USB device number 2 using ehci-platform <6>[ 4.754115] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 4.754136] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 4.757297] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 4.761166] usbcore: registered new interface driver usbhid <6>[ 4.816930] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0) <6>[ 4.817304] usbhid: USB HID core driver <6>[ 4.826204] mmc0: new high speed MMC card at address 0001 <6>[ 4.833784] NET: Registered protocol family 10 <6>[ 4.843134] mmcblk0: mmc0:0001 032GE4 29.1 GiB <6>[ 4.853820] Segment Routing with IPv6 <6>[ 4.860150] mmcblk0boot0: mmc0:0001 032GE4 partition 1 4.00 MiB <6>[ 4.871202] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.875936] mmcblk0boot1: mmc0:0001 032GE4 partition 2 4.00 MiB <6>[ 4.882306] NET: Registered protocol family 17 <6>[ 4.897105] mmcblk0rpmb: mmc0:0001 032GE4 partition 3 4.00 MiB, chardev (235:0) <6>[ 4.903950] can: controller area network core <6>[ 4.913906] mmcblk0: p1 p2 <6>[ 4.917792] NET: Registered protocol family 29 <6>[ 4.938158] hub 3-1:1.0: USB hub found <6>[ 4.940023] can: raw protocol <6>[ 4.945602] hub 3-1:1.0: 4 ports detected <6>[ 4.949755] can: broadcast manager protocol <6>[ 4.963082] can: netlink gateway - max_hops=1 <5>[ 4.968451] Key type dns_resolver registered <6>[ 4.973551] ThumbEE CPU extension supported. <5>[ 4.978621] Registering SWP/SWPB emulation handler <5>[ 4.984362] Loading compiled-in X.509 certificates <6>[ 5.011372] rk_gmac-dwmac ff290000.ethernet: IRQ eth_lpi not found <6>[ 5.018653] rk_gmac-dwmac ff290000.ethernet: PTP uses main clock <6>[ 5.026248] rk_gmac-dwmac ff290000.ethernet: clock input or output? (input). <6>[ 5.034419] rk_gmac-dwmac ff290000.ethernet: TX delay(0x30). <6>[ 5.041053] rk_gmac-dwmac ff290000.ethernet: RX delay(0x10). <6>[ 5.047676] rk_gmac-dwmac ff290000.ethernet: integrated PHY? (no). <3>[ 5.054897] rk_gmac-dwmac ff290000.ethernet: cannot get clock clk_mac_speed <6>[ 5.062972] rk_gmac-dwmac ff290000.ethernet: clock input from PHY <6>[ 5.075083] rk_gmac-dwmac ff290000.ethernet: init for RGMII <6>[ 5.081740] rk_gmac-dwmac ff290000.ethernet: User ID: 0x10, Synopsys ID: 0x35 <6>[ 5.090021] rk_gmac-dwmac ff290000.ethernet: DWMAC1000 <6>[ 5.096149] rk_gmac-dwmac ff290000.ethernet: DMA HW capability register supported <6>[ 5.104808] rk_gmac-dwmac ff290000.ethernet: RX Checksum Offload Engine supported <6>[ 5.113458] rk_gmac-dwmac ff290000.ethernet: COE Type 2 <6>[ 5.119589] rk_gmac-dwmac ff290000.ethernet: TX Checksum insertion supported <6>[ 5.127765] rk_gmac-dwmac ff290000.ethernet: Wake-Up On Lan supported <6>[ 5.135292] rk_gmac-dwmac ff290000.ethernet: Normal descriptors <6>[ 5.142204] rk_gmac-dwmac ff290000.ethernet: Ring mode enabled <6>[ 5.149018] rk_gmac-dwmac ff290000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 5.271608] RTL8211E Gigabit Ethernet stmmac-0:00: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:00, irq=POLL) <6>[ 5.285912] RTL8211E Gigabit Ethernet stmmac-0:01: attached PHY driver [RTL8211E Gigabit Ethernet] (mii_bus:phy_addr=stmmac-0:01, irq=POLL) <3>[ 5.303933] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <6>[ 5.303986] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <3>[ 5.312995] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <3>[ 5.330197] debugfs: Directory 'power-domain' with parent 'pm_genpd' already present! <6>[ 5.339437] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 5.339776] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 5.347130] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 5.347143] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 5.375561] rk_gmac-dwmac ff290000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211E Gigabit Ethernet] (irq=POLL) <6>[ 5.388762] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 5.396248] rk_gmac-dwmac ff290000.ethernet eth0: No Safety Features support found <6>[ 5.396995] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <4>[ 5.405678] rk_gmac-dwmac ff290000.ethernet eth0: PTP not supported by HW <6>[ 5.413361] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 5.427765] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 5.438853] rk_gmac-dwmac ff290000.ethernet eth0: configuring for phy/rgmii link mode <6>[ 9.577643] rk_gmac-dwmac ff290000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 9.596792] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 9.626288] Sending DHCP requests ., OK <6>[ 9.691480] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.22 <6>[ 9.700741] IP-Config: Complete: <6>[ 9.704651] device=eth0, hwaddr=4a:01:9c:e5:04:ff, ipaddr=192.168.201.22, mask=255.255.255.0, gw=192.168.201.1 <6>[ 9.716657] host=rk3288-rock2-square-cbg-0, domain=lava-rack, nis-domain=(none) <6>[ 9.725612] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 9.725620] nameserver0=192.168.201.1 <6>[ 9.739051] clk: Disabling unused clocks <4>[ 9.744843] dw-apb-uart ff690000.serial: forbid DMA for kernel console <6>[ 9.756650] Freeing unused kernel memory: 2048K <6>[ 9.776391] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 9.837419] udevd[120]: starting version 3.2.9 <5>[ 9.843188] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.851071] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 9.858648] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 9.870051] udevd[120]: specified user 'tss' unknown <27>[ 9.876040] udevd[120]: specified group 'tss' unknown <30>[ 9.882840] udevd[121]: starting eudev-3.2.9 <6>[ 10.028073] rockchip-vop ff930000.vop: Adding to iommu group 0 <6>[ 10.035135] rockchip-vop ff940000.vop: Adding to iommu group 1 <6>[ 10.046335] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 10.046539] rockchip-drm display-subsystem: bound ff930000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 10.082131] rockchip-drm display-subsystem: bound ff940000.vop (ops vop_component_ops [rockchipdrm]) <6>[ 10.092798] dwhdmi-rockchip ff980000.hdmi: Detected HDMI TX controller v2.00a with HDCP (DWC MHL PHY) <6>[ 10.106304] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 10.113994] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 10.120550] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 10.161242] rockchip-drm display-subsystem: bound ff980000.hdmi (ops dw_hdmi_rockchip_ops [rockchipdrm]) <6>[ 10.172766] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes <6>[ 10.187622] dwmmc_rockchip ff0d0000.mmc: IDMAC supports 32-bit address mode. <6>[ 10.193007] [drm] Initialized rockchip 1.0.0 20140818 for display-subsystem on minor 0 <6>[ 10.207813] rtc-hym8563 0-0051: registered as rtc0 <6>[ 10.213509] dwmmc_rockchip ff0d0000.mmc: Using internal DMA controller. <6>[ 10.221205] rtc-hym8563 0-0051: setting system clock to 2024-06-06T00:36:40 UTC (1717634200) <6>[ 10.221235] dwmmc_rockchip ff0d0000.mmc: Version ID is 270a <6>[ 10.237483] dwmmc_rockchip ff0d0000.mmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo <6>[ 10.281932] dwmmc_rockchip ff0d0000.mmc: allocated mmc-pwrseq <6>[ 10.288669] mmc_host mmc2: card is non-removable. <6>[ 10.316327] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) <6>[ 10.341211] panfrost ffa30000.gpu: clock rate = 400000000 <6>[ 10.350655] rk3288-crypto ff8a0000.crypto: will run requests pump with realtime priority <6>[ 10.353007] panfrost ffa30000.gpu: mali-t760 id 0x750 major 0x0 minor 0x0 status 0x1 <6>[ 10.368976] panfrost ffa30000.gpu: features: 00000000,100277bf, issues: 00000000,24040400 <6>[ 10.378424] panfrost ffa30000.gpu: Features: L2:0x07120206 Shader:0x00000000 Tiler:0x00000809 Mem:0x1 MMU:0x00002830 AS:0xff JS:0x7 <6>[ 10.391944] panfrost ffa30000.gpu: shader_present=0xf l2_present=0x1 <6>[ 10.393246] rk3288-crypto ff8a0000.crypto: Crypto Accelerator successfully registered <6>[ 10.399853] [drm] Initialized panfrost 1.1.0 20180908 for ffa30000.gpu on minor 1 <4>[ 10.426454] mmc2: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 10.434361] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <4>[ 10.442292] mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <4>[ 10.451410] mmc2: queuing unknown CIS tuple 0x80 (7 bytes) done Saving random seed: OK <6>[ 10.511301] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) Starting network: <6>[ 10.526326] mmc2: new high speed SDIO card at address 0001 ip: RTNETLINK answers: File exists FAIL <5>[ 10.552933] cfg80211: Loading compiled-in X.509 certificates for regulatory database Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # <5>[ 10.587902] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <5>[ 10.596447] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600' <4>[ 10.605837] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 10.614223] br cmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <6>[ 10.615800] cfg80211: failed to load regulatory.db <4>[ 10.625908] brcmfmac mmc2:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-14191865/environment . /lava-14191865/environment / # /lava-14191865/bin/lava-test-runner /lava-14191865/0 /lava-14191865/bin/lava-test-runner /lava-14191865/0 + export 'TESTRUN_ID=0_dmesg' + <8>[ 11.169830] cd /lava-14191865/0/tests/0_dmesg + cat uuid + UUID=14191865_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 11.194042] <8>[ 11.214926] <8>[ 11.234964] + <8>[ 11.245169] set +x / # <6>[ 11.256307] rockchip-drm display-subsystem: [drm] Cannot find any crtc or sizes