Trying 192.168.1.205... Connected to ts5. Escape character is '^]'. ser2net port telnet,2002 device serialdev,/dev/ttyUSB-lf-bbb-02,115200n81,local [] (Debian GNU/Linux) U-Boot SPL 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) Trying to boot from MMC2 U-Boot 2021.10-nethacked-for-LAVA_hws@denx.de-dirty (Oct 19 2021 - 19:02:35 +0200) CPU : AM335X-GP rev 2.1 Model: TI AM335x BeagleBone Black DRAM: 512 MiB WDT: Started with servicing (60s timeout) NAND: 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... not set. Validating first E-fuse MAC Net: eth2: ethernet@4a100000, eth3: usb_ether Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 172.16.3.193 (60 ms) => setenv serverip 172.16.3.3 setenv serverip 172.16.3.3 => tftp 0x82000000 1217116/tftp-deploy-jjoj3ti0/kernel/zImage tftp 0x82000000 1217116/tftp-deploy-jjoj3ti0/kernel/zImage link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.193 Filename '1217116/tftp-deploy-jjoj3ti0/kernel/zImage'. Load address: 0x82000000 Loading: *################################################## 4.4 MiB 3.8 MiB/s done Bytes transferred = 4648272 (46ed50 hex) => tftp 0x83000000 1217116/tftp-deploy-jjoj3ti0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 1217116/tftp-deploy-jjoj3ti0/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.193 Filename '1217116/tftp-deploy-jjoj3ti0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################## 13.5 MiB 4.4 MiB/s done Bytes transferred = 14152154 (d7f1da hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1217116/tftp-deploy-jjoj3ti0/dtb/am335x-boneblack.dtb tftp 0x88000000 1217116/tftp-deploy-jjoj3ti0/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using ethernet@4a100000 device TFTP from server 172.16.3.3; our IP address is 172.16.3.193 Filename '1217116/tftp-deploy-jjoj3ti0/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *################################################## 61.4 KiB 3.2 MiB/s done Bytes transferred = 62861 (f58d hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 Kernel image @ 0x82000000 [ 0x000000 - 0x46ed50 ] ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2024-11-05 15:06:02 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 14152090 Bytes = 13.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801258c Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.228-cip53 (KernelCI@build-j363334-arm-gcc-12-omap2plus-defconfig-z8sdn) (arm-linux-gnueabihf-gcc (Debian 12.2.0-14) 12.2.0, GNU ld (GNU Binutils for Debian) 2.40) #1 SMP Tue Nov 5 14:40:46 UTC 2024 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] cma: Reserved 16 MiB at 0x9e800000 [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49740 r8192 d23988 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129412 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon deferred_probe_timeout=60 ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off <6>[ 0.000000] Memory: 471016K/522240K available (10240K kernel code, 1029K rwdata, 2176K rodata, 1024K init, 281K bss, 34840K reserved, 16384K cma-reserved, 0K highmem) <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000011] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008343] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.018563] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.030220] Console: colour dummy device 80x30 <3>[ 0.035091] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.042149] This ensures that you still see kernel messages. Please <3>[ 0.048874] update your kernel commandline. <6>[ 0.053478] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.095541] CPU: Testing write buffer coherency: ok <6>[ 0.100923] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.106388] pid_max: default: 32768 minimum: 301 <6>[ 0.111552] LSM: Security Framework initializing <6>[ 0.116653] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.124471] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.134146] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.140651] Setting up static identity map for 0x80100000 - 0x80100078 <6>[ 0.147839] rcu: Hierarchical SRCU implementation. <6>[ 0.153633] smp: Bringing up secondary CPUs ... <6>[ 0.158570] smp: Brought up 1 node, 1 CPU <6>[ 0.162996] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.169724] CPU: All CPU(s) started in SVC mode. <6>[ 0.175452] devtmpfs: initialized <6>[ 0.191254] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.199791] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.210232] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.218712] pinctrl core: initialized pinctrl subsystem <6>[ 0.226376] NET: Registered protocol family 16 <6>[ 0.233963] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.260442] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.266515] audit: initializing netlink subsys (disabled) <6>[ 0.273577] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.273593] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.280207] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.286923] cpuidle: using governor menu <5>[ 1.648259] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1 <6>[ 1.835870] No ATAGs? <6>[ 1.838498] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.868410] Kprobes globally optimized <6>[ 1.881636] iommu: Default domain type: Translated <6>[ 1.888658] vgaarb: loaded <5>[ 1.892365] SCSI subsystem initialized <6>[ 1.897661] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.903145] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.912869] PTP clock support registered <6>[ 1.918432] clocksource: Switched to clocksource dmtimer <5>[ 2.548627] VFS: Disk quotas dquot_6.6.0 <6>[ 2.553041] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <6>[ 2.569753] NET: Registered protocol family 2 <6>[ 2.574828] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.583541] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.592510] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.600809] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.608491] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.615411] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.622441] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.630066] NET: Registered protocol family 1 <6>[ 2.635829] RPC: Registered named UNIX socket transport module. <6>[ 2.642293] RPC: Registered udp transport module. <6>[ 2.647400] RPC: Registered tcp transport module. <6>[ 2.652527] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.659457] PCI: CLS 0 bytes, default 64 <6>[ 2.664487] Trying to unpack rootfs image as initramfs... <6>[ 3.626983] Freeing initrd memory: 13824K <6>[ 3.632695] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.643073] Initialise system trusted keyrings <6>[ 3.648517] workingset: timestamp_bits=14 max_order=17 bucket_order=3 <5>[ 3.656819] NFS: Registering the id_resolver key type <5>[ 3.662431] Key type id_resolver registered <5>[ 3.667004] Key type id_legacy registered <6>[ 3.671473] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. <5>[ 3.679467] Key type asymmetric registered <5>[ 3.683962] Asymmetric key parser 'x509' registered <6>[ 3.689306] io scheduler mq-deadline registered <6>[ 3.694236] io scheduler kyber registered <3>[ 3.902100] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.910795] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 4.071692] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 4.129637] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 4.232890] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.241588] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 4.326067] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.334763] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 4.357027] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 4.365712] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 4.453198] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 4.461758] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.490245] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.504794] Serial: 8250/16550 driver, 6 ports, IRQ sharing enabled <6>[ 4.515778] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.525222] printk: console [ttyS0] enabled <6>[ 4.525222] printk: console [ttyS0] enabled <6>[ 4.534293] printk: bootconsole [omap8250] disabled <6>[ 4.534293] printk: bootconsole [omap8250] disabled <6>[ 4.557984] brd: module loaded <6>[ 4.568796] loop: module loaded <3>[ 4.574273] mtdoops: mtd device (mtddev=name/number) must be supplied <6>[ 4.638399] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.681149] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.691058] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.697711] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.703524] cpsw 4a100000.ethernet: cpts: overflow check period 500 (jiffies) <6>[ 4.711084] cpsw 4a100000.ethernet: Detected MACID = 04:79:b7:e7:06:e0 <6>[ 4.720113] i2c /dev entries driver <5>[ 4.725602] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.733556] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.740098] sdhci: Copyright(c) Pierre Ossman <6>[ 4.745465] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.753762] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.763529] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.771999] Initializing XFRM netlink socket <6>[ 4.776794] NET: Registered protocol family 10 <6>[ 4.783227] Segment Routing with IPv6 <6>[ 4.787270] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.794348] NET: Registered protocol family 17 <6>[ 4.799200] NET: Registered protocol family 15 <5>[ 4.804043] Key type dns_resolver registered <6>[ 4.809225] oprofile: using arm/armv7 <6>[ 4.813265] ThumbEE CPU extension supported. <5>[ 4.817832] Registering SWP/SWPB emulation handler <3>[ 4.823384] omap_voltage_late_init: Voltage driver support not added <3>[ 4.830103] sr_dev_init: No voltage domain specified for smartreflex0. Cannot initialize <3>[ 4.838517] sr_dev_init: No voltage domain specified for smartreflex1. Cannot initialize <6>[ 4.847186] SmartReflex Class3 initialized <6>[ 4.852114] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.861013] Loading compiled-in X.509 certificates <6>[ 4.885844] OMAP GPIO hardware version 0.1 <4>[ 4.919108] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.932797] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.941676] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <6>[ 4.948054] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <6>[ 4.958103] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 4.969547] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 4.978643] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 4.983809] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.994179] mmc1: new high speed MMC card at address 0001 <6>[ 5.001142] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 5.006394] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.013102] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.020542] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (249:0) <6>[ 5.030857] mmcblk1: p1 <6>[ 5.054687] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.064373] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.149956] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 8.289098] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 8.318431] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.348529] Sending DHCP requests ., OK <6>[ 8.412540] IP-Config: Got DHCP answer from 172.16.3.3, my address is 172.16.3.193 <6>[ 8.420448] IP-Config: Complete: <6>[ 8.423958] device=eth0, hwaddr=04:79:b7:e7:06:e0, ipaddr=172.16.3.193, mask=255.255.255.0, gw=172.16.3.3 <6>[ 8.434293] host=172.16.3.193, domain=denx.de, nis-domain=(none) <6>[ 8.441043] bootserver=172.16.3.33, rootserver=172.16.3.33, rootpath= <6>[ 8.441050] nameserver0=172.16.3.3 <6>[ 8.452344] ntpserver0=172.16.3.3 <6>[ 8.456868] clk: Disabling unused clocks <6>[ 8.463240] Freeing unused kernel memory: 1024K <6>[ 8.478928] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.712719] udevd[100]: starting version 3.2.9 <5>[ 8.719847] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.727002] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.734524] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.751782] udevd[100]: specified user 'tss' unknown <27>[ 8.757356] udevd[100]: specified group 'tss' unknown <30>[ 8.778827] udevd[101]: starting eudev-3.2.9 <4>[ 9.421175] at24 0-0050: supply vcc not found, using dummy regulator <4>[ 9.468117] tps6521x_pwrbutton tps65217-pwrbutton: DMA mask not set <6>[ 9.565704] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <4>[ 9.573427] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 9.584604] remoteproc remoteproc0: wkup_m3 is available <3>[ 9.616944] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 9.669614] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <6>[ 9.689521] input: tps65217_pwrbutton as /devices/platform/ocp/44c00000.interconnect/44c00000.interconnect:segment@200000/44e0b000.target-module/44e0b000.i2c/i2c-0/0-0024/tps65217-pwrbutton/input/input0 <6>[ 9.719145] omap_rtc 44e3e000.rtc: registered as rtc0 <6>[ 9.724565] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01T00:00:00 UTC (946684800) <4>[ 9.792750] at24 2-0055: supply vcc not found, using dummy regulator <6>[ 9.800213] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec <6>[ 9.826217] usbcore: registered new interface driver usbfs <6>[ 9.832221] usbcore: registered new interface driver hub <6>[ 9.837906] usbcore: registered new device driver usb <6>[ 9.866792] tda998x 0-0070: found TDA19988 <4>[ 9.872091] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 9.933701] at24 2-0057: supply vcc not found, using dummy regulator <3>[ 9.996189] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <4>[ 10.150059] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <3>[ 10.161336] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <3>[ 10.272094] wkup_m3_ipc 44e11324.wkup_m3_ipc: IPC Request for A8->M3 Channel failed! -517 <6>[ 10.289074] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 10.294727] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 10.355954] omap-mailbox 480c8000.mailbox: omap mailbox rev 0x400 <3>[ 10.467769] davinci-mcasp 48038000.mcasp: IRQ common not found <6>[ 10.605593] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 10.615136] random: crng init done <6>[ 10.643997] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 <6>[ 10.652739] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 10.660301] usb usb1: Product: MUSB HDRC host driver <6>[ 10.665552] usb usb1: Manufacturer: Linux 5.10.228-cip53 musb-hcd <6>[ 10.671954] usb usb1: SerialNumber: musb-hdrc.1 <6>[ 10.724224] tilcdc 4830e000.lcdc: bound 0-0070 (ops tda998x_driver_exit [tda998x]) <6>[ 10.760296] [drm] Initialized tilcdc 1.0.0 20121205 for 4830e000.lcdc on minor 0 <6>[ 10.807026] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 10.816846] tilcdc 4830e000.lcdc: [drm] Cannot find any crtc or sizes <6>[ 10.924202] hub 1-0:1.0: USB hub found <6>[ 10.963855] hub 1-0:1.0: 1 port detected <3>[ 11.003999] PM: Cannot get wkup_m3_ipc handle <6>[ 11.019057] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 <6>[ 11.042929] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 <3>[ 11.105426] PM: Cannot get wkup_m3_ipc handle <6>[ 11.110911] remoteproc remoteproc0: powering up wkup_m3 <4>[ 11.116567] remoteproc remoteproc0: Direct firmware load for am335x-pm-firmware.elf failed with error -2 <3>[ 11.126460] remoteproc remoteproc0: request_firmware failed: -2 <3>[ 11.132711] wkup_m3_ipc 44e11324.wkup_m3_ipc: rproc_boot failed <6>[ 11.157000] omap-aes 53500000.aes: will run requests pump with realtime priority <6>[ 11.177597] omap-sham 53100000.sham: will run requests pump with realtime priority <3>[ 11.215987] PM: Cannot get wkup_m3_ipc handle <3>[ 11.270346] PM: Cannot get wkup_m3_ipc handle <3>[ 11.564895] PM: Cannot get wkup_m3_ipc handle <3>[ 11.600228] PM: Cannot get wkup_m3_ipc handle done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1217116/environment . /lava-1217116/environment / # /lava-1217116/bin/lava-test-runner /lava-1217116/0 /lava-1217116/bin/lava-test-runner /lava-1217116/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1217116/0/tests/0_dmesg + cat uuid + UUID=1217116_1.5.2.4.1 <8>[ 12.647441] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.714143] <8>[ 12.774973] <8>[ 12.835673] + set +x <8>[ 12.846921] / #