connecting to NetworkSerialPort(target=Target(name='at91-sama5d4_xplained', env=None), name='USBSerialPort', state=, avail=True, host='nuc-1', port=60273, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-1:60273 connected to 192.168.0.1 (port 60273) Escape character: Ctrl-\ Type the escape character to get to the prompt. RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  0 U-Boot> setenv autoload no setenv autoload no U-Boot> setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff U-Boot> setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff U-Boot> dhcp dhcp gmac0: PHY present at 0 gmac0: Starting autonegotiation... gmac0: Autonegotiation complete gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) BOOTP broadcast 1 DHCP client bound to address 192.168.0.135 U-Boot> setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 U-Boot> tftp 0x22100000 3164133/tftp-deploy-ns9bnri8/kernel/zImage tftp 0x22100000 3164133/tftp-deploy-ns9bnri8/kernel/zImage gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3164133/tftp-deploy-ns9bnri8/kernel/zImage'. Load address: 0x22100000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 3 MiB/s done Bytes transferred = 8729088 (853200 hex) U-Boot> tftp 0x23000000 3164133/tftp-deploy-ns9bnri8/ramdisk/ramdisk.cpio.gz.uboot tftp 0x23000000 3164133/tftp-deploy-ns9bnri8/ramdisk/ramdisk.cpio.gz.uboot gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3164133/tftp-deploy-ns9bnri8/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x23000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 3.2 MiB/s done Bytes transferred = 13342394 (cb96ba hex) U-Boot> setenv initrd_size ${filesize} setenv initrd_size ${filesize} U-Boot> tftp 0x22000000 3164133/tftp-deploy-ns9bnri8/dtb/at91-sama5d4_xplained.dtb tftp 0x22000000 3164133/tftp-deploy-ns9bnri8/dtb/at91-sama5d4_xplained.dtb gmac0: PHY present at 0 gmac0: link up, 100Mbps full-duplex (lpa: 0x45e1) Using gmac0 device TFTP from server 192.168.0.2; our IP address is 192.168.0.135 Filename '3164133/tftp-deploy-ns9bnri8/dtb/at91-sama5d4_xplained.dtb'. Load address: 0x22000000 Loading: *### 2.2 MiB/s done Bytes transferred = 32907 (808b hex) U-Boot> setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' U-Boot> bootz 0x22100000 0x23000000 0x22000000 bootz 0x22100000 0x23000000 0x22000000 Kernel image @ 0x22100000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 23000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13342330 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 22000000 Booting using the fdt blob at 0x22000000 Using Device Tree in place at 22000000, end 2200b08a Starting kernel ... <6>[ 0.000000] Booting Linux on physical CPU 0x0 <5>[ 0.000000] Linux version 4.19.269-cip45-rt119 (KernelCI@build-j877779-arm-gcc-10-multi-v7-defconfig-87w6g) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Jan 18 22:54:23 UTC 2023 <6>[ 0.000000] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d <6>[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache <6>[ 0.000000] OF: fdt: Machine model: Atmel SAMA5D4 Xplained <4>[ 0.000000] Malformed early option 'earlycon' <6>[ 0.000000] Memory policy: Data cache writeback <6>[ 0.000000] efi: Getting EFI parameters from FDT: <6>[ 0.000000] efi: UEFI not found. <6>[ 0.000000] cma: Reserved 64 MiB at 0x3c000000 <6>[ 0.000000] CPU: All CPU(s) started in SVC mode. <6>[ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 <6>[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 <5>[ 0.000000] Kernel command line: console=ttyAT0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) <6>[ 0.000000] Memory: 419412K/524288K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 39340K reserved, 65536K cma-reserved, 0K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xe0800000 - 0xff800000 ( 496 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 erratum 769419 enabled <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 8 ways, 128 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x06020000 <6>[ 0.000000] clocksource: pit: mask: 0x7ffffff max_cycles: 0x7ffffff, max_idle_ns: 10859434279 ns <6>[ 0.000000] Console: colour dummy device 80x30 <6>[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns <6>[ 0.050000] Calibrating delay loop... 348.97 BogoMIPS (lpj=1744896) <6>[ 0.050000] pid_max: default: 32768 minimum: 301 <6>[ 0.050000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.050000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) <6>[ 0.050000] CPU: Testing write buffer coherency: ok <6>[ 0.050000] CPU0: thread -1, cpu 0, socket -1, mpidr c0000000 <6>[ 0.050000] Setting up static identity map for 0x20300000 - 0x203000a0 <6>[ 0.050000] rcu: Hierarchical SRCU implementation. <6>[ 0.060000] EFI services will not be available. <6>[ 0.060000] smp: Bringing up secondary CPUs ... <6>[ 0.060000] smp: Brought up 1 node, 1 CPU <6>[ 0.060000] SMP: Total of 1 processors activated (348.97 BogoMIPS). <6>[ 0.060000] CPU: All CPU(s) started in SVC mode. <6>[ 0.060000] devtmpfs: initialized <6>[ 0.070000] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 <6>[ 0.080000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.080000] futex hash table entries: 256 (order: 2, 16384 bytes) <6>[ 0.080000] pinctrl core: initialized pinctrl subsystem <6>[ 0.080000] DMI not present or invalid. <6>[ 0.090000] NET: Registered protocol family 16 <6>[ 0.090000] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.100000] cpuidle: using governor menu <6>[ 0.130000] AT91: PM: standby: standby, suspend: ulp0 <6>[ 0.130000] No ATAGs? <6>[ 0.130000] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.130000] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.130000] gpio-at91 fc06a000.gpio: at address (ptrval) <6>[ 0.130000] gpio-at91 fc06b000.gpio: at address (ptrval) <6>[ 0.130000] gpio-at91 fc06c000.gpio: at address (ptrval) <6>[ 0.130000] gpio-at91 fc068000.gpio: at address (ptrval) <6>[ 0.130000] gpio-at91 fc06d000.gpio: at address (ptrval) <6>[ 0.130000] pinctrl-at91 ahb:apb:pinctrl@fc06a000: initialized AT91 pinctrl driver <6>[ 0.140000] Serial: AMBA PL011 UART driver <6>[ 0.150000] clocksource: tcb_clksrc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 173750949719 ns <6>[ 0.170000] at_xdmac f0004000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.180000] at_xdmac f0014000.dma-controller: 16 channels, mapped at 0x(ptrval) <6>[ 0.180000] AT91: Detected SoC family: sama5d4 <6>[ 0.180000] AT91: Detected SoC: sama5d44, revision 0 <6>[ 0.180000] VDD MCI1: supplied by VCC 3V3 <6>[ 0.190000] vgaarb: loaded <5>[ 0.190000] SCSI subsystem initialized <6>[ 0.190000] usbcore: registered new interface driver usbfs <6>[ 0.190000] usbcore: registered new interface driver hub <6>[ 0.190000] usbcore: registered new device driver usb <6>[ 0.190000] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.190000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.190000] PTP clock support registered <6>[ 0.190000] EDAC MC: Ver: 3.0.0 <6>[ 0.200000] clocksource: Switched to clocksource tcb_clksrc <6>[ 0.310000] NET: Registered protocol family 2 <6>[ 0.310000] IP idents hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.310000] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.310000] TCP established hash table entries: 4096 (order: 2, 16384 bytes) <6>[ 0.310000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) <6>[ 0.310000] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 0.310000] UDP hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.310000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) <6>[ 0.310000] NET: Registered protocol family 1 <6>[ 0.310000] RPC: Registered named UNIX socket transport module. <6>[ 0.310000] RPC: Registered udp transport module. <6>[ 0.310000] RPC: Registered tcp transport module. <6>[ 0.310000] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.310000] Trying to unpack rootfs image as initramfs... <6>[ 2.370000] Freeing initrd memory: 13032K <5>[ 2.370000] Initialise system trusted keyrings <6>[ 2.370000] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 2.390000] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 2.390000] NFS: Registering the id_resolver key type <5>[ 2.390000] Key type id_resolver registered <5>[ 2.390000] Key type id_legacy registered <6>[ 2.390000] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 2.400000] Key type asymmetric registered <5>[ 2.400000] Asymmetric key parser 'x509' registered <6>[ 2.400000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 2.400000] io scheduler noop registered <6>[ 2.400000] io scheduler deadline registered <6>[ 2.400000] io scheduler cfq registered (default) <6>[ 2.400000] io scheduler mq-deadline registered <6>[ 2.400000] io scheduler kyber registered <6>[ 2.570000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 2.580000] SuperH (H)SCI(F) driver initialized <6>[ 2.580000] f8004000.serial: ttyAT5 at MMIO 0xf8004000 (irq = 23, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 2.580000] fc00c000.serial: ttyAT0 at MMIO 0xfc00c000 (irq = 29, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 3.330000] console [ttyAT0] enabled <6>[ 3.340000] fc010000.serial: ttyAT1 at MMIO 0xfc010000 (irq = 30, base_baud = 5500000) is a ATMEL_SERIAL <6>[ 3.350000] msm_serial: driver initialized <6>[ 3.350000] STMicroelectronics ASC driver initialized <6>[ 3.360000] STM32 USART driver initialized <6>[ 3.400000] brd: module loaded <6>[ 3.420000] loop: module loaded <6>[ 3.450000] CAN device driver interface <6>[ 3.610000] Micrel KSZ8081 or KSZ8091 f8020000.ethernet-ffffffff:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=f8020000.ethernet-ffffffff:01, irq=46) <6>[ 3.630000] macb f8020000.ethernet eth0: Cadence GEM rev 0x00020120 at 0xf8020000 irq 27 (52:11:6d:6b:d5:8f) <6>[ 3.640000] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.640000] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 3.650000] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.660000] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 3.660000] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.680000] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.690000] usbcore: registered new interface driver pegasus <6>[ 3.690000] usbcore: registered new interface driver asix <6>[ 3.700000] usbcore: registered new interface driver ax88179_178a <6>[ 3.700000] usbcore: registered new interface driver cdc_ether <6>[ 3.710000] usbcore: registered new interface driver smsc75xx <6>[ 3.720000] usbcore: registered new interface driver smsc95xx <6>[ 3.720000] usbcore: registered new interface driver net1080 <6>[ 3.730000] usbcore: registered new interface driver cdc_subset <6>[ 3.730000] usbcore: registered new interface driver zaurus <6>[ 3.740000] usbcore: registered new interface driver cdc_ncm <6>[ 3.750000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.760000] ehci-pci: EHCI PCI platform driver <6>[ 3.760000] ehci-platform: EHCI generic platform driver <6>[ 3.770000] ehci-orion: EHCI orion driver <6>[ 3.770000] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.780000] ehci-st: EHCI STMicroelectronics driver <6>[ 3.780000] ehci-exynos: EHCI EXYNOS driver <6>[ 3.790000] ehci-atmel: EHCI Atmel driver <6>[ 3.800000] atmel-ehci 600000.ehci: EHCI Host Controller <6>[ 3.800000] atmel-ehci 600000.ehci: new USB bus registered, assigned bus number 1 <6>[ 3.810000] atmel-ehci 600000.ehci: irq 18, io mem 0x00600000 <6>[ 3.850000] atmel-ehci 600000.ehci: USB 2.0 started, EHCI 1.00 <6>[ 3.850000] hub 1-0:1.0: USB hub found <6>[ 3.860000] hub 1-0:1.0: 3 ports detected <6>[ 3.860000] tegra-ehci: Tegra EHCI driver <6>[ 3.870000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.870000] ohci-pci: OHCI PCI platform driver <6>[ 3.880000] ohci-platform: OHCI generic platform driver <6>[ 3.880000] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.890000] ohci-st: OHCI STMicroelectronics driver <6>[ 3.890000] ohci-atmel: OHCI Atmel driver <6>[ 3.900000] at91_ohci 500000.ohci: USB Host Controller <6>[ 3.910000] at91_ohci 500000.ohci: new USB bus registered, assigned bus number 2 <6>[ 3.920000] at91_ohci 500000.ohci: irq 18, io mem 0x00500000 <6>[ 3.990000] hub 2-0:1.0: USB hub found <6>[ 3.990000] hub 2-0:1.0: 3 ports detected <6>[ 4.000000] usbcore: registered new interface driver usb-storage <6>[ 4.020000] i2c /dev entries driver <6>[ 4.030000] at91-reset fc068600.rstc: Starting after wakeup <6>[ 4.050000] sama5d4_wdt fc068640.watchdog: initialized (timeout = 16 sec, nowayout = 0) <6>[ 4.070000] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.070000] sdhci: Copyright(c) Pierre Ossman <6>[ 4.080000] atmel_mci fc000000.mmc: version: 0x600 <6>[ 4.090000] atmel_mci fc000000.mmc: using dma0chan0 for DMA transfers <6>[ 4.090000] atmel_mci fc000000.mmc: Linked as a consumer to regulator.2 <6>[ 4.100000] atmel_mci fc000000.mmc: Linked as a consumer to regulator.1 <6>[ 4.130000] atmel_mci fc000000.mmc: Atmel MCI controller at 0xfc000000 irq 28, 1 slots <6>[ 4.140000] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.150000] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.160000] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.170000] usbcore: registered new interface driver usbhid <6>[ 4.180000] usbhid: USB HID core driver <6>[ 4.190000] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xdc <6>[ 4.200000] nand: Micron MT29F4G08ABAEAWP <6>[ 4.210000] nand: 512 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 <6>[ 4.220000] Bad block table found at page 131008, version 0x01 <6>[ 4.220000] Bad block table found at page 130944, version 0x01 <5>[ 4.230000] 6 fixed-partitions partitions found on MTD device atmel_nand <5>[ 4.240000] Creating 6 MTD partitions on \"atmel_nand\": <5>[ 4.240000] 0x000000000000-0x000000040000 : \"at91bootstrap\" <5>[ 4.250000] 0x000000040000-0x0000000c0000 : \"bootloader\" <5>[ 4.260000] 0x0000000c0000-0x000000180000 : \"bootloader env\" <5>[ 4.260000] 0x000000180000-0x000000200000 : \"device tree\" <5>[ 4.270000] 0x000000200000-0x000000800000 : \"kernel\" <5>[ 4.280000] 0x000000800000-0x000020000000 : \"rootfs\" <6>[ 4.300000] NET: Registered protocol family 10 <6>[ 4.310000] Segment Routing with IPv6 <6>[ 4.310000] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.320000] NET: Registered protocol family 17 <6>[ 4.330000] can: controller area network core (rev 20170425 abi 9) <6>[ 4.330000] NET: Registered protocol family 29 <6>[ 4.340000] can: raw protocol (rev 20170425) <6>[ 4.340000] can: broadcast manager protocol (rev 20170425 t) <6>[ 4.350000] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 4.350000] Key type dns_resolver registered <6>[ 4.360000] ThumbEE CPU extension supported. <5>[ 4.360000] Registering SWP/SWPB emulation handler <5>[ 4.370000] Loading compiled-in X.509 certificates <6>[ 4.390000] input: gpio_keys as /devices/platform/gpio_keys/input/input0 <6>[ 4.400000] hctosys: unable to open rtc device (rtc0) <6>[ 4.410000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 5.250000] macb f8020000.ethernet eth0: link up (100/Full) <6>[ 5.280000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 5.310000] Sending DHCP requests ., OK <6>[ 5.350000] IP-Config: Got DHCP answer from 192.168.0.1, my address is 192.168.0.135 <6>[ 5.360000] IP-Config: Complete: <6>[ 5.360000] device=eth0, hwaddr=52:11:6d:6b:d5:8f, ipaddr=192.168.0.135, mask=255.255.255.0, gw=192.168.0.254 <6>[ 5.370000] host=192.168.0.135, domain=lan, nis-domain=(none) <6>[ 5.380000] bootserver=192.168.0.1, rootserver=192.168.0.1, rootpath= <6>[ 5.380000] nameserver0=192.168.0.1, nameserver1=192.168.1.254 <6>[ 5.390000] atmel_usart fc00c000.serial: using dma0chan2 for rx DMA transfers <6>[ 5.400000] atmel_usart fc00c000.serial: using dma0chan3 for tx DMA transfers <6>[ 5.410000] Freeing unused kernel memory: 2048K <6>[ 5.420000] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 5.820000] udevd[78]: starting version 3.2.9 <5>[ 5.820000] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.830000] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 5.840000] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 5.870000] udevd[78]: specified user 'tss' unknown <27>[ 5.870000] udevd[78]: specified group 'tss' unknown <30>[ 5.890000] udevd[79]: starting eudev-3.2.9 <6>[ 8.340000] atmel_spi f8010000.spi: Using dma0chan4 (tx) and dma0chan5 (rx) for DMA transfers <3>[ 8.440000] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, 00, 00 <6>[ 8.450000] atmel_spi f8010000.spi: Atmel SPI Controller version 0x221 at 0xf8010000 (irq 24) <6>[ 8.460000] atmel_spi fc018000.spi: Using dma0chan6 (tx) and dma0chan7 (rx) for DMA transfers <6>[ 8.520000] at91_i2c f8014000.i2c: using dma0chan8 (tx) and dma0chan9 (rx) for DMA transfers <6>[ 8.630000] at91_i2c f8014000.i2c: AT91 i2c bus driver (hw version: 0x502). <6>[ 8.710000] atmel_spi fc018000.spi: Atmel SPI Controller version 0x221 at 0xfc018000 (irq 31) <6>[ 8.970000] iio iio:device0: Resolution used: 10 bits <6>[ 8.980000] iio iio:device0: ADC Touch screen is disabled. <6>[ 8.990000] atmel_aes fc044000.aes: version: 0x201 <6>[ 9.000000] atmel_sha fc050000.sha: version: 0x420 <6>[ 9.010000] atmel_sha fc050000.sha: using dma1chan2 for DMA transfers <6>[ 9.020000] atmel_tdes fc04c000.tdes: version: 0x702 <6>[ 9.030000] atmel_tdes fc04c000.tdes: using dma1chan3, dma1chan4 for DMA transfers <6>[ 9.170000] atmel_aes fc044000.aes: Atmel AES - Using dma1chan0, dma1chan1 for DMA transfers <6>[ 9.200000] at91_rtc fc0686b0.rtc: registered as rtc0 <6>[ 9.210000] at91_rtc fc0686b0.rtc: AT91 Real Time Clock driver. <6>[ 9.220000] atmel_sha fc050000.sha: Atmel SHA1/SHA256/SHA224/SHA384/SHA512 <6>[ 9.270000] atmel_tdes fc04c000.tdes: Atmel DES/TDES done Saving random seed: <5>[ 11.460000] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 11.680000] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  2  1  0 Rien a faire U-Boot> # # U-Boot> # # U-Boot> # # U-Boot> RomBOOT All interupts redirected to AIC ACT8865: Set REG1/REG2/REG3 power saving mode ACT8865: The REG5 output 3300mV ACT8865: The REG6 output 1800mV ACT8865: Disable ACT8865's I2C interface HDMI SiI9022: Enter D3 Cold mode PHY: GMAC0 KSZ8081RNB: Enter power down mode AT91Bootstrap 3.7.1 (Thu Oct 30 15:25:32 CST 2014) EEPROM: Loading AT24xx information ... EEPROM: BoardName | [Revid] | VendorName HW Info: The total size isn't correct 1-Wire: Using default information 1-Wire: Board sn: 0x1012420, revsion: 0x680820 NAND: ONFI flash detected NAND: Manufacturer ID: 0x2c Chip ID: 0x34 NAND: Disable On-Die ECC NAND: Initialize PMECC params, cap: 0x8, sector: 0x200 NAND: Image: Copy 0x80000 bytes from 0x40000 to 0x26f00000 NAND: Done to load image U-Boot 2014.07 (Oct 29 2014 - 16:59:40) CPU: SAMA5D4 Crystal frequency: 12 MHz CPU clock : 528 MHz Master clock : 176 MHz DRAM: 512 MiB NAND: 512 MiB MMC: mci: 0 In: serial Out: serial Err: serial Net: gmac0 Hit any key to stop autoboot: 3  2  1  0 Rien a faire U-Boot> # # U-Boot>