Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3009 device /dev/ttyimx7d-sdb-2 [115200 N81] (Debian GNU/Linux) U-Boot 2016.03-imx_v2016.03_4.1.15_2.0.0_ga+g0ec2a01 (Nov 11 2016 - 03:13:54 -0600) CPU: Freescale i.MX7D rev1.3 996 MHz (running at 792 MHz) CPU: Commercial temperature grade (0C to 95C) at 26C Reset cause: POR Board: i.MX7D SABRESD RevA I2C: ready DRAM: 1 GiB PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x11 MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc0 is current device Net: FEC0 Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.166 (1329 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1140311/tftp-deploy-n176s8zj/kernel/zImage tftp 0x80800000 1140311/tftp-deploy-n176s8zj/kernel/zImage Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1140311/tftp-deploy-n176s8zj/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 10.3 MiB/s done Bytes transferred = 8729088 (853200 hex) => tftp 0x86800000 1140311/tftp-deploy-n176s8zj/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1140311/tftp-deploy-n176s8zj/ramdisk/ramdisk.cpio.gz.uboot Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1140311/tftp-deploy-n176s8zj/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################ 10.4 MiB/s done Bytes transferred = 13335906 (cb7d62 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1140311/tftp-deploy-n176s8zj/dtb/imx7d-sdb.dtb tftp 0x83000000 1140311/tftp-deploy-n176s8zj/dtb/imx7d-sdb.dtb Using FEC0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.166; sending through gateway 172.16.1.4 Filename '1140311/tftp-deploy-n176s8zj/dtb/imx7d-sdb.dtb'. Load address: 0x83000000 Loading: *### 4.6 MiB/s done Bytes transferred = 33576 (8328 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x853200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13335842 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300b327 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.269-cip45-rt119 (KernelCI@build-j877779-arm-gcc-10-multi-v7-defconfig-87w6g) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Jan 18 22:54:23 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX7 SabreSD Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x30860000 (options '') [ 0.000000] bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xbc000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939300K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 43740K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=2. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (virt). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000007] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008313] Switching to timer-based delay loop, resolution 125ns <6>[ 0.015746] Switching to timer-based delay loop, resolution 41ns <6>[ 0.021005] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.029140] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.042376] Console: colour dummy device 80x30 <6>[ 0.044279] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.054928] pid_max: default: 32768 minimum: 301 <6>[ 0.059957] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.066746] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.074689] CPU: Testing write buffer coherency: ok <6>[ 0.079616] CPU0: update cpu_capacity 1024 <6>[ 0.083614] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.090278] Setting up static identity map for 0x80300000 - 0x803000a0 <6>[ 0.097728] rcu: Hierarchical SRCU implementation. <6>[ 0.104591] EFI services will not be available. <6>[ 0.106753] smp: Bringing up secondary CPUs ... <6>[ 0.112144] smp: Brought up 1 node, 1 CPU <6>[ 0.115642] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.122147] CPU: All CPU(s) started in SVC mode. <6>[ 0.127917] devtmpfs: initialized <6>[ 0.137498] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.142999] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.152806] futex hash table entries: 512 (order: 3, 32768 bytes) <6>[ 0.161661] pinctrl core: initialized pinctrl subsystem <6>[ 0.166362] DMI not present or invalid. <6>[ 0.169898] NET: Registered protocol family 16 <6>[ 0.175578] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.183114] cpuidle: using governor menu <6>[ 0.185506] No ATAGs? <6>[ 0.185612] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.195753] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.204391] Serial: AMBA PL011 UART driver <6>[ 0.213899] imx7d-pinctrl 302c0000.iomuxc-lpsr: initialized IMX pinctrl driver <4>[ 0.219447] imx7d-pinctrl 30330000.iomuxc: Failed to create dummy-iomuxc-gpr@30340000 debugfs directory <6>[ 0.228544] imx7d-pinctrl 30330000.iomuxc: initialized IMX pinctrl driver <6>[ 0.237098] vdd1p0d: Bringing 0uV into 800000-800000uV <6>[ 0.240961] vdd1p0d: supplied by regulator-dummy <6>[ 0.246222] vdd1p2: supplied by regulator-dummy <6>[ 0.291844] mxs-dma 33000000.dma-apbh: initialized <6>[ 0.300279] vgaarb: loaded <5>[ 0.301289] SCSI subsystem initialized <6>[ 0.304955] usbcore: registered new interface driver usbfs <6>[ 0.310292] usbcore: registered new interface driver hub <6>[ 0.315833] usbcore: registered new device driver usb <6>[ 0.322441] i2c i2c-0: IMX I2C adapter registered <6>[ 0.326126] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.332345] i2c i2c-1: IMX I2C adapter registered <6>[ 0.336710] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.342737] i2c i2c-2: IMX I2C adapter registered <6>[ 0.347297] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.353477] i2c i2c-3: IMX I2C adapter registered <6>[ 0.357885] i2c i2c-3: can't use DMA, using PIO instead. <6>[ 0.364958] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.368730] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.378224] PTP clock support registered <6>[ 0.382577] EDAC MC: Ver: 3.0.0 <6>[ 0.388740] clocksource: Switched to clocksource arch_sys_counter <6>[ 0.452689] NET: Registered protocol family 2 <6>[ 0.454754] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.462551] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.469495] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.476860] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.483672] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.490285] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.496427] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.503221] NET: Registered protocol family 1 <6>[ 0.508308] RPC: Registered named UNIX socket transport module. <6>[ 0.513920] RPC: Registered udp transport module. <6>[ 0.518889] RPC: Registered tcp transport module. <6>[ 0.523854] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.531146] Trying to unpack rootfs image as initramfs... <6>[ 1.625536] Freeing initrd memory: 13024K <6>[ 1.627670] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 1.637243] Initialise system trusted keyrings <6>[ 1.640512] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.654254] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.658506] NFS: Registering the id_resolver key type <5>[ 1.663133] Key type id_resolver registered <5>[ 1.667317] Key type id_legacy registered <6>[ 1.671666] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.678444] Key type asymmetric registered <5>[ 1.680667] Asymmetric key parser 'x509' registered <6>[ 1.685838] bounce: pool size: 64 pages <6>[ 1.689956] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 1.697595] io scheduler noop registered <6>[ 1.701811] io scheduler deadline registered <6>[ 1.706602] io scheduler cfq registered (default) <6>[ 1.711351] io scheduler mq-deadline registered <6>[ 1.716142] io scheduler kyber registered <4>[ 1.739053] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 1.745010] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 1.752092] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 1.770897] imx7-pgc imx7-pgc-domain.1: DMA mask not set <6>[ 1.773733] imx7-pgc imx7-pgc-domain.1: Linked as a consumer to regulator.1 <4>[ 1.785616] reset_imx7 30390000.src: Failed to create dummy-src@30390000 debugfs directory <4>[ 1.793530] imx-sdma 30bd0000.sdma: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <6>[ 1.801255] imx-sdma 30bd0000.sdma: external firmware not found, using ROM firmware <6>[ 1.860524] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.867864] SuperH (H)SCI(F�0 0<6>[ 1.871936] console [ttymxc0] enabled <6>[ 1.871936] console [ttymxc0] enabled <6>[ 1.876914] bootconsole [ec_imx6q0] disabled <6>[ 1.876914] bootconsole [ec_imx6q0] disabled <6>[ 1.886934] 30a80000.serial: ttymxc5 at MMIO 0x30a80000 (irq = 57, base_baud = 15000000) is a IMX <6>[ 1.899252] msm_serial: driver initialized <6>[ 1.903823] STMicroelectronics ASC driver initialized <6>[ 1.910280] STM32 USART driver initialized <6>[ 1.933078] brd: module loaded <6>[ 1.943948] loop: module loaded <6>[ 1.959765] CAN device driver interface <6>[ 1.964990] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 1.973411] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 1.982570] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 1.989561] fec 30be0000.ethernet: Dropping the link to regulator.0 <4>[ 1.998100] fec 30bf0000.ethernet: 30bf0000.ethernet supply phy not found, using dummy regulator <6>[ 2.007263] fec 30bf0000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.014522] pps pps0: new PPS source ptp0 <3>[ 2.019653] fec 30bf0000.ethernet: Invalid MAC address: 00:00:00:00:00:00 <6>[ 2.026761] fec 30bf0000.ethernet: Using random MAC address: 7e:10:2a:83:60:32 <6>[ 2.828420] fec 30bf0000.ethernet eth0: registered PHC device 0 <6>[ 2.835840] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.841989] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.848238] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.855483] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.866250] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.874005] usbcore: registered new interface driver pegasus <6>[ 2.880003] usbcore: registered new interface driver asix <6>[ 2.885701] usbcore: registered new interface driver ax88179_178a <6>[ 2.892112] usbcore: registered new interface driver cdc_ether <6>[ 2.898254] usbcore: registered new interface driver smsc75xx <6>[ 2.904330] usbcore: registered new interface driver smsc95xx <6>[ 2.910398] usbcore: registered new interface driver net1080 <6>[ 2.916355] usbcore: registered new interface driver cdc_subset <6>[ 2.922591] usbcore: registered new interface driver zaurus <6>[ 2.928521] usbcore: registered new interface driver cdc_ncm <6>[ 2.936949] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.943781] ehci-pci: EHCI PCI platform driver <6>[ 2.948532] ehci-platform: EHCI generic platform driver <6>[ 2.954280] ehci-orion: EHCI orion driver <6>[ 2.958751] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.963167] ehci-st: EHCI STMicroelectronics driver <6>[ 2.968448] ehci-exynos: EHCI EXYNOS driver <6>[ 2.973057] ehci-atmel: EHCI Atmel driver <6>[ 2.977465] tegra-ehci: Tegra EHCI driver <6>[ 2.981928] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.988389] ohci-pci: OHCI PCI platform driver <6>[ 2.993170] ohci-platform: OHCI generic platform driver <6>[ 2.998898] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.003317] ohci-st: OHCI STMicroelectronics driver <6>[ 3.008600] ohci-atmel: OHCI Atmel driver <6>[ 3.013744] usbcore: registered new interface driver usb-storage <6>[ 3.026688] i2c /dev entries driver <6>[ 3.043259] imx2-wdt 30280000.wdog: timeout 60 sec (nowayout=0) <6>[ 3.054682] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.061195] sdhci: Copyright(c) Pierre Ossman <6>[ 3.067708] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.075612] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.082434] sdhci-esdhc-imx 30b40000.usdhc: Got CD GPIO <6>[ 3.087953] sdhci-esdhc-imx 30b40000.usdhc: Got WP GPIO <6>[ 3.126134] mmc0: SDHCI controller on 30b40000.usdhc [30b40000.usdhc] using ADMA <6>[ 3.134768] sdhci-esdhc-imx 30b50000.usdhc: Linked as a consumer to regulator.6 <6>[ 3.187257] mmc0: new high speed SDHC card at address aaaa <6>[ 3.194051] mmcblk0: mmc0:aaaa SA16G 14.8 GiB <6>[ 3.201528] mmcblk0: p1 p2 <6>[ 3.390331] mmc1: SDHCI controller on 30b50000.usdhc [30b50000.usdhc] using ADMA <6>[ 3.431877] mmc2: SDHCI controller on 30b60000.usdhc [30b60000.usdhc] using ADMA <6>[ 3.443080] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.450204] usbcore: registered new interface driver usbhid <6>[ 3.456041] usbhid: USB HID core driver <6>[ 3.465522] NET: Registered protocol family 10 <6>[ 3.471677] Segment Routing with IPv6 <6>[ 3.475677] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.482538] NET: Registered protocol family 17 <6>[ 3.487258] can: controller area network core (rev 20170425 abi 9) <6>[ 3.493806] NET: Registered protocol family 29 <6>[ 3.498516] can: raw protocol (rev 20170425) <6>[ 3.503071] can: broadcast manager protocol (rev 20170425 t) <6>[ 3.509018] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 3.515268] Key type dns_resolver registered <6>[ 3.519946] ThumbEE CPU extension supported. <5>[ 3.524490] Registering SWP/SWPB emulation handler <5>[ 3.531439] Loading compiled-in X.509 certificates <4>[ 3.561285] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) <4>[ 3.571271] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 3.580136] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 3.587304] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 3.599571] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 3.608815] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.615834] fec 30be0000.ethernet: Dropping the link to regulator.0 <4>[ 3.632258] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 3.641116] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 3.648282] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 3.660458] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 3.669646] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <4>[ 3.676641] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) <6>[ 3.682494] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 3.698765] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <6>[ 3.706195] hctosys: unable to open rtc device (rtc0) <4>[ 3.715073] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 3.723918] pwm-backlight backlight: Linked as a consumer to regulator.0 <3>[ 3.734653] fec 30bf0000.ethernet eth0: Unable to connect to phy <3>[ 3.744515] IP-Config: Failed to open eth0 <3>[ 3.748931] IP-Config: No network devices available <6>[ 3.755872] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 3.768181] mmc1: queuing unknown CIS tuple 0x80 (6 bytes) <4>[ 3.791640] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 3.800828] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 3.811189] Freeing unused kernel memory: 2048K <6>[ 3.816105] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 3.839127] Run /init as init process Starting syslogd: OK Starting klogd: <6>[ 3.978936] mmc1: new ultra high speed SDR104 SDIO card at address 0001 OK Running sysctl: OK Populating /dev using udev: <30>[ 4.059335] udevd[122]: starting version 3.2.9 <5>[ 4.065122] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 4.072617] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 4.079537] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 4.096273] udevd[122]: specified user 'tss' unknown <27>[ 4.101807] udevd[122]: specified group 'tss' unknown <30>[ 4.120340] udevd[123]: starting eudev-3.2.9 <6>[ 5.234325] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 5.241274] [drm] No driver support for vblank timestamp query. <3>[ 5.247585] mxsfb 30730000.lcdif: Failed to create outputs <6>[ 5.311707] flexcan 30a10000.can: Linked as a consumer to regulator.7 <6>[ 5.319286] flexcan 30a10000.can: device registered (reg_base=(ptrval), irq=52) <4>[ 5.330526] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 5.339368] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 5.429292] pwm-backlight backlight: Dropping the link to regulator.0 <5>[ 5.558620] cfg80211: Loading compiled-in X.509 certificates for regulatory database <4>[ 5.567071] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 5.576267] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 5.652045] fec 30be0000.ethernet: Dropping the link to regulator.0 <4>[ 5.668551] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 5.677443] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 5.863017] pwm-backlight backlight: Dropping the link to regulator.0 <4>[ 5.875658] usb_phy_generic usbphynop1: usbphynop1 supply vcc not found, using dummy regulator <6>[ 5.884739] usb_phy_generic usbphynop1: Linked as a consumer to regulator.0 <4>[ 5.892220] usb_phy_generic usbphynop3: usbphynop3 supply vcc not found, using dummy regulator <6>[ 5.901173] usb_phy_generic usbphynop3: Linked as a consumer to regulator.0 <4>[ 5.908680] usb_phy_generic usbphynop2: usbphynop2 supply vcc not found, using dummy regulator <6>[ 5.917636] usb_phy_generic usbphynop2: Linked as a consumer to regulator.0 <6>[ 5.953595] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 5.960526] [drm] No driver support for vblank timestamp query. <3>[ 5.966818] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 6.061826] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 6.071013] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 6.120082] fec 30be0000.ethernet: Dropping the link to regulator.0 <6>[ 6.129654] imx_usb 30b10000.usb: Linked as a consumer to regulator.3 <6>[ 6.212901] imx_usb 30b20000.usb: Linked as a consumer to regulator.4 <5>[ 6.224544] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' <4>[ 6.231704] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 <6>[ 6.240620] cfg80211: failed to load regulatory.db <6>[ 6.290498] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 6.295695] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 6.332483] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4339-sdio for chip BCM4339/2 <4>[ 6.365254] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac4339-sdio.bin failed with error -2 <6>[ 6.378912] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 6.396324] hub 1-0:1.0: USB hub found <6>[ 6.414270] hub 1-0:1.0: 1 port detected <4>[ 6.444242] pwm-backlight backlight: backlight supply power not found, using dummy regulator <6>[ 6.453138] pwm-backlight backlight: Linked as a consumer to regulator.0 <6>[ 6.529258] pwm-backlight backlight: Dropping the link to regulator.0 <6>[ 6.572067] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). <6>[ 6.579003] [drm] No driver support for vblank timestamp query. <3>[ 6.585296] mxsfb 30730000.lcdif: Failed to create outputs <4>[ 6.662948] fec 30be0000.ethernet: 30be0000.ethernet supply phy not found, using dummy regulator <6>[ 6.672141] fec 30be0000.ethernet: Linked as a consumer to regulator.0 <6>[ 6.728331] fec 30be0000.ethernet: Dropping the link to regulator.0 done Saving random seed: <5>[ 6.894388] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 6.980891] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh expo<3>[ 7.429116] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000): clkctl 0x50 rt SHELL=/bin/sh / # . /lava-1140311/environment . /lava-1140311/environment / # /lava-1140311/bin/lava-test-runner /lava-1140311/0 /lava-1140311/bin/lava-test-runner /lava-1140311/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1140311/0/tests/0_dmesg + cat uuid <8>[ 12.795710] + UUID=1140311_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 12.841557] <8>[ 12.884129] <8>[ 12.926985] + set +x <8>[ 12.936977] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1140311/environment / # . /lava-1140311/environment/lava-1140311/bin/lava-test-runner /lava-1140311/1 / # /lava-1140311/bin/lava-test-runner /lava-1140311/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1140311/1/tests/1_bootrr + cat uuid + UUID=114031<8>[ 18.657046] 1_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1140311/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto tempmon cpufreq-dt regulator-lcd-3v3 backlight panel 30730000.lcdif 30be0000.ethernet /lava-1140311/1/../bin/lava-test-case <8>[ 19.716204] /lava-1140311/1/../bin/lava-test-case <8>[ 20.759480] /lava-1140311/1/../bin/lava-test-case <8>[ 20.784290] + set +x <8>[ 20.803092] / #