[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9727640/tftp-deploy-re4vf0wo/kernel/zImage tftp 0x10000000 9727640/tftp-deploy-re4vf0wo/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9727640/tftp-deploy-re4vf0wo/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 11.5 MiB/s done Bytes transferred = 8733184 (854200 hex) => tftp 0x14000000 9727640/tftp-deploy-re4vf0wo/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9727640/tftp-deploy-re4vf0wo/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9727640/tftp-deploy-re4vf0wo/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 5.3 MiB/s done Bytes transferred = 13352319 (cbbd7f hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9727640/tftp-deploy-re4vf0wo/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9727640/tftp-deploy-re4vf0wo/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '9727640/tftp-deploy-re4vf0wo/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 4 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x854200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13352255 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.277-cip94-rt29 (KernelCI@build-j1226218-arm-gcc-10-multi-v7-defconfig-9ttxr) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Mar 22 09:06:14 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939108K/1048576K available (12288K kernel code, 1597K rwdata, 4684K rodata, 2048K init, 394K bss, 43932K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1598 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000006] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021460] Console: colour dummy device 80x30 <6>[ 0.023343] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033761] pid_max: default: 32768 minimum: 301 <6>[ 0.038757] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045506] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053346] CPU: Testing write buffer coherency: ok <6>[ 0.057950] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063609] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069867] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077589] rcu: Hierarchical SRCU implementation. <6>[ 0.084353] EFI services will not be available. <6>[ 0.086604] smp: Bringing up secondary CPUs ... <6>[ 0.091984] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091990] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.103327] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.103334] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114522] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114528] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124861] smp: Brought up 1 node, 4 CPUs <6>[ 0.129115] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135531] CPU: All CPU(s) started in SVC mode. <6>[ 0.141499] devtmpfs: initialized <6>[ 0.151531] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156985] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166736] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.176307] pinctrl core: initialized pinctrl subsystem <6>[ 0.180558] DMI not present or invalid. <6>[ 0.183874] NET: Registered protocol family 16 <6>[ 0.191252] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197923] cpuidle: using governor menu <6>[ 0.199894] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214879] vdd1p1: supplied by regulator-dummy <6>[ 0.217353] vdd3p0: supplied by regulator-dummy <6>[ 0.222072] vdd2p5: supplied by regulator-dummy <6>[ 0.226909] vddarm: supplied by regulator-dummy <6>[ 0.231815] vddpu: supplied by regulator-dummy <6>[ 0.236260] vddsoc: supplied by regulator-dummy <6>[ 0.255081] No ATAGs? <6>[ 0.255217] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.263172] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.272811] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.279683] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.291803] Serial: AMBA PL011 UART driver <6>[ 0.295721] console [pstore-1] enabled <6>[ 0.297476] pstore: Registered ramoops as persistent store backend <6>[ 0.303763] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.332465] mxs-dma 110000.dma-apbh: initialized <6>[ 0.342239] vgaarb: loaded <5>[ 0.343200] SCSI subsystem initialized <6>[ 0.346764] usbcore: registered new interface driver usbfs <6>[ 0.352163] usbcore: registered new interface driver hub <6>[ 0.357698] usbcore: registered new device driver usb <6>[ 0.364271] i2c i2c-0: IMX I2C adapter registered <6>[ 0.367938] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.374072] i2c i2c-1: IMX I2C adapter registered <6>[ 0.378467] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.384461] i2c i2c-2: IMX I2C adapter registered <6>[ 0.388989] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.396186] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.399771] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.409196] PTP clock support registered <6>[ 0.413594] EDAC MC: Ver: 3.0.0 <6>[ 0.419542] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.482853] NET: Registered protocol family 2 <6>[ 0.485058] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.492625] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.499562] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.506891] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.513673] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.520341] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.526333] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.533098] NET: Registered protocol family 1 <6>[ 0.538116] RPC: Registered named UNIX socket transport module. <6>[ 0.543727] RPC: Registered udp transport module. <6>[ 0.548657] RPC: Registered tcp transport module. <6>[ 0.553628] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.560813] Trying to unpack rootfs image as initramfs... <6>[ 1.687558] Freeing initrd memory: 13040K <4>[ 1.689394] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.696703] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.706737] Initialise system trusted keyrings <6>[ 1.709763] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.722161] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.726126] NFS: Registering the id_resolver key type <5>[ 1.730764] Key type id_resolver registered <5>[ 1.735149] Key type id_legacy registered <6>[ 1.739452] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.746150] Key type asymmetric registered <5>[ 1.748377] Asymmetric key parser 'x509' registered <6>[ 1.753579] bounce: pool size: 64 pages <6>[ 1.757632] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.765275] io scheduler noop registered <6>[ 1.769429] io scheduler deadline registered <6>[ 1.774187] io scheduler cfq registered (default) <6>[ 1.778914] io scheduler mq-deadline registered <6>[ 1.783716] io scheduler kyber registered <6>[ 1.811103] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.815666] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.822794] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.830080] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.850845] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.854235] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.862084] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.868258] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.876194] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.879563] PU : no governor for states <6>[ 1.885777] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.889873] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.962970] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.970425] SuperH (H)SCI(F) driver initialized <6>[ 1.973291] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.982060] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.993001] console [ttymxc1] enabled <6>[ 1.993001] console [ttymxc1] enabled <6>[ 1.997983] bootconsole [ec_imx21] disabled <6>[ 1.997983] bootconsole [ec_imx21] disabled <6>[ 2.008122] msm_serial: driver initialized <6>[ 2.014370] STMicroelectronics ASC driver initialized <6>[ 2.021621] STM32 USART driver initialized <4>[ 2.037309] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.046005] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.053020] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.059805] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.068838] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.076001] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.090795] brd: module loaded <6>[ 2.103577] loop: module loaded <6>[ 2.110343] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.118537] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.126843] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.135306] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.146090] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.153375] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.162452] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.173276] scsi host0: ahci-imx <6>[ 2.177354] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.196853] CAN device driver interface <6>[ 2.202287] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.209377] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.218341] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.227434] pps pps0: new PPS source ptp0 <6>[ 2.258377] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.265859] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.271979] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.278228] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.285473] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.297429] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.305157] usbcore: registered new interface driver pegasus <6>[ 2.311150] usbcore: registered new interface driver asix <6>[ 2.316851] usbcore: registered new interface driver ax88179_178a <6>[ 2.323261] usbcore: registered new interface driver cdc_ether <6>[ 2.329403] usbcore: registered new interface driver smsc75xx <6>[ 2.335483] usbcore: registered new interface driver smsc95xx <6>[ 2.341544] usbcore: registered new interface driver net1080 <6>[ 2.347513] usbcore: registered new interface driver cdc_subset <6>[ 2.353749] usbcore: registered new interface driver zaurus <6>[ 2.359674] usbcore: registered new interface driver cdc_ncm <6>[ 2.368631] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.375459] ehci-pci: EHCI PCI platform driver <6>[ 2.380232] ehci-platform: EHCI generic platform driver <6>[ 2.386030] ehci-orion: EHCI orion driver <6>[ 2.390561] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.395035] ehci-st: EHCI STMicroelectronics driver <6>[ 2.400394] ehci-exynos: EHCI EXYNOS driver <6>[ 2.405036] ehci-atmel: EHCI Atmel driver <6>[ 2.409500] tegra-ehci: Tegra EHCI driver <6>[ 2.414035] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.420514] ohci-pci: OHCI PCI platform driver <6>[ 2.425269] ohci-platform: OHCI generic platform driver <6>[ 2.431065] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.435543] ohci-st: OHCI STMicroelectronics driver <6>[ 2.440906] ohci-atmel: OHCI Atmel driver <6>[ 2.446197] usbcore: registered new interface driver usb-storage <6>[ 2.454834] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.466965] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.477161] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.482358] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.519581] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.520989] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.530977] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.537514] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.545272] hub 1-0:1.0: USB hub found <6>[ 2.549332] hub 1-0:1.0: 1 port detected <6>[ 2.560128] i2c /dev entries driver <6>[ 2.578930] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.590542] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.596989] sdhci: Copyright(c) Pierre Ossman <6>[ 2.604017] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.612385] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.619178] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.624636] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.630170] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.670033] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.678044] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.683590] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.723419] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.735071] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.742171] usbcore: registered new interface driver usbhid <6>[ 2.748012] usbhid: USB HID core driver <6>[ 2.758267] NET: Registered protocol family 10 <6>[ 2.764075] Segment Routing with IPv6 <6>[ 2.768091] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.774855] NET: Registered protocol family 17 <6>[ 2.779607] can: controller area network core (rev 20170425 abi 9) <6>[ 2.786119] NET: Registered protocol family 29 <6>[ 2.790857] can: raw protocol (rev 20170425) <6>[ 2.795397] can: broadcast manager protocol (rev 20170425 t) <6>[ 2.801345] can: netlink gateway (rev 20170425) max_hops=1 <5>[ 2.807483] Key type dns_resolver registered <6>[ 2.813099] cpu cpu0: Linked as a consumer to regulator.4 <6>[ 2.818818] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.824586] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.831063] ThumbEE CPU extension supported. <5>[ 2.835611] Registering SWP/SWPB emulation handler <5>[ 2.841583] Loading compiled-in X.509 certificates <6>[ 2.848119] pstore: Using compression: deflate <6>[ 2.854076] mmc0: new high speed SDHC card at address e624 <6>[ 2.862205] mmcblk0: mmc0:e624 SL16G 14.8 GiB <6>[ 2.866085] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.874366] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.883229] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.889578] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.890721] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.899742] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 2.906218] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <4>[ 2.912164] GPT:7812499 != 31116287 <6>[ 2.920831] panel-simple panel-lcd: Linked as a consumer to regulator.0 <4>[ 2.924542] GPT:Alternate GPT header not at the end of the disk. <6>[ 2.931505] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.937696] GPT:7812499 != 31116287 <4>[ 2.945607] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <4>[ 2.948071] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.957093] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.962493] mmcblk0: p1 p2 p3 <6>[ 2.969577] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.981579] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.992077] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.999437] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.007846] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.015343] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.023990] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.032663] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.039636] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.047515] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.056539] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.063682] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.071473] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.078824] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.087048] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.094540] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 3.101923] hub 1-1:1.0: USB hub found <4>[ 3.103257] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.106077] hub 1-1:1.0: 3 ports detected <6>[ 3.114623] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.125825] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.133791] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.142827] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.149980] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.157736] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.165136] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.173347] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.180833] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.189393] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.198072] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.205046] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 3.213343] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.220242] hctosys: unable to open rtc device (rtc0) <4>[ 3.227050] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.236141] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.243314] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.251301] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.258677] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.267059] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.274548] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.283172] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.291855] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.298810] panel-simple panel-lcd: Dropping the link to regulator.0 <6>[ 3.350549] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.365520] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.480207] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.489627] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.519709] Sending DHCP requests ., OK <6>[ 6.563794] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 6.572098] IP-Config: Complete: <6>[ 6.575598] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.586317] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 6.594432] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.594436] nameserver0=192.168.201.1 <6>[ 6.612127] Freeing unused kernel memory: 2048K <6>[ 6.629841] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.759171] udevd[112]: starting version 3.2.9 <5>[ 6.765485] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.772559] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.779384] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.793751] udevd[112]: specified user 'tss' unknown <27>[ 6.799188] udevd[112]: specified group 'tss' unknown <30>[ 6.806756] udevd[113]: starting eudev-3.2.9 <4>[ 7.113109] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.122244] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.135880] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.135954] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.150031] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.158169] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.158378] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.173625] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.185454] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.192710] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.199586] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.207826] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.215524] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.224951] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.233699] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.240840] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.249450] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.258555] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.265769] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.274173] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.281702] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.289051] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.296144] sgtl5000 0-000a: Linked as a consumer to regulator.8 <6>[ 7.302685] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.308390] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.310235] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.325410] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.334193] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.341469] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.350633] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.356467] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.359706] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.362011] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.381107] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.396427] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.402830] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.410141] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.411026] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.424863] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.434248] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.442809] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.452652] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.461376] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.468436] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.477287] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.486372] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.493649] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.502397] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.509967] pwm-backlight backlight-lcd: Dropping the link to regulator.8 done Saving random seed: <5>[ 8.012363] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 8.099482] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-9727640/environment . /lava-9727640/environment / # /lava-9727640/bin/lava-test-runner /lava-9727640/0 /lava-9727640/bin/lava-test-runner /lava-9727640/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-9727640/0/tests/0_dmesg + cat uuid <8>[ 8.700601] + UUID=9727640_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.745231] <8>[ 8.786209] <8>[ 8.827223] + set +x <8>[ 8.837161] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-9727640/environment / # . /lava-9727640/environment/lava-9727640/bin/lava-test-runner /lava-9727640/1 / # /lava-9727640/bin/lava-test-runner /lava-9727640/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-9727640/1/tests/1_bootrr + cat uuid + UUID=9727640_<8>[ 9.340004] 1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-9727640/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto backlight-lvds panel-lcd panel-lvds0 backlight-lcd /lava-9727640/1/../bin/lava-test-case <8>[ 10.410614] /lava-9727640/1/../bin/lava-test-case <8>[ 10.450066] /lava-9727640/1/../bin/lava-test-case <8>[ 10.474892] + set +x <8>[ 10.493692] / #