Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3016 device /dev/ttyfsl-ls1088a-rdb-1 [115200 N81] (Debian GNU/Linux) NOTICE: UDIMM 18ASF1G72AZ-2G3B1 NOTICE: 8 GB DDR4, 64-bit, CL=15, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.09 NOTICE: BL2: Built : 21:15:09, Oct 17 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.09 NOTICE: BL31: Built : 21:15:17, Oct 17 2019 NOTICE: Welcome to LS1088 BL31 Phase U-Boot 2019.04-gce862bb2d2 (Oct 17 2019 - 17:03:51 +0800) SoC: LS1048AE Rev1.0 (0x87032010) Clock Configuration: CPU0(A53):1600 MHz CPU1(A53):1600 MHz CPU2(A53):1600 MHz CPU3(A53):1600 MHz Bus: 700 MHz DDR: 2100 MT/s Reset Configuration Word (RCW): 00000000: 4000541c 00000040 00000000 00000000 00000010: 00000000 000a0000 00300000 00000000 00000020: 034011a0 00002580 00000000 00000040 00000030: 0000005b 00000000 00002403 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00000011 000009e7 00000070: 44110000 00107777 VID: Core voltage after adjustment is at 1025 mV DRAM: 7.9 GiB DDR 7.9 GiB (DDR4, 64-bit, CL=15, ECC on) DDR Chip-Select Interleaving Mode: CS0+CS1 Using SERDES1 Protocol: 29 (0x1d) Using SERDES2 Protocol: 19 (0x13) NAND: 512 MiB MMC: FSL_SDHC: 0 Loading Environment from SPI Flash... SF: Detected s25fl512s with page size 256 Bytes, erase size 256 KiB, total 64 MiB OK EEPROM: NXID v1 In: serial Out: serial Err: serial Model: NXP Layerscape 1088a RDB Board Board: LS1088A-RDB, Board Arch: V1, Board version: B, boot from QSPI:1 CPLD: v1.8 SERDES1 Reference : Clock1 = 100MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz Net: PHY reset timed out PCIe0: pcie@3400000 Root Complex: no link PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 e1000: 00:1b:21:39:54:35 DPMAC2@xgmii, DPMAC3@qsgmii, DPMAC4@qsgmii, DPMAC5@qsgmii, DPMAC6@qsgmii, DPMAC7@qsgmii, DPMAC8@qsgmii, DPMAC9@qsgmii, DPMAC10@qsgmii, e1000#0 [PRIME] Warning: e1000#0 MAC addresses don't match: Address in SROM is 00:1b:21:39:54:35 Address in environment is 00:04:9f:04:78:27 SF: Detected s25fl512s with page size 256 Bytes, erase size 256 KiB, total 64 MiB device 0 offset 0xa00000, size 0x100000 SF: 1048576 bytes @ 0xa00000 Read: OK device 0 offset 0xe00000, size 0x100000 SF: 1048576 bytes @ 0xe00000 Read: OK crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.18.0, boot status: 0x1) Hit any key to stop autoboot: 2  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => setenv ipaddr 172.16.1.41; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.41; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x82000000 1181543/tftp-deploy-hvxmu7t9/kernel/Image tftp 0x82000000 1181543/tftp-deploy-hvxmu7t9/kernel/Image Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.41 Filename '1181543/tftp-deploy-hvxmu7t9/kernel/Image'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################# 2.7 MiB/s done Bytes transferred = 19565056 (12a8a00 hex) => tftp 0x8f000000 1181543/tftp-deploy-hvxmu7t9/ramdisk/ramdisk.cpio.gz.uboot tftp 0x8f000000 1181543/tftp-deploy-hvxmu7t9/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.41 Filename '1181543/tftp-deploy-hvxmu7t9/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x8f000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################################### 2.2 MiB/s done Bytes transferred = 15235325 (e878fd hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 1181543/tftp-deploy-hvxmu7t9/dtb/fsl-ls1088a-rdb.dtb tftp 0x88000000 1181543/tftp-deploy-hvxmu7t9/dtb/fsl-ls1088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.41 Filename '1181543/tftp-deploy-hvxmu7t9/dtb/fsl-ls1088a-rdb.dtb'. Load address: 0x88000000 Loading: *# 2 KiB/s done Bytes transferred = 12014 (2eee hex) => setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 arm-smmu.disable_bypass=0console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyS0,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 arm-smmu.disable_bypass=0console_msg_format=syslog earlycon ip=dhcp' => booti 0x82000000 0x8f000000 0x88000000 booti 0x82000000 0x8f000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 8f000000 ... Image Name: Created: 2023-03-22 9:38:58 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 15235261 Bytes = 14.5 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Ramdisk to faca9000, end fbb308bd ... OK Loading Device Tree to 00000000faca3000, end 00000000faca8eed ... OK WARNING: fdt_fixup_stdout: could not read serial0 alias: FDT_ERR_NOTFOUND WARNING failed to get smmu node: FDT_ERR_NOTFOUND fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 4.19.277-cip94-rt29 (KernelCI@build-j1226306-arm64-gcc-10-defconfig-qsfjm) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Wed Mar 22 09:27:09 UTC 2023 [ 0.000000] Machine model: LS1088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0500 (options '') [ 0.000000] bootconsole [uart8250] enabled [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 32 MiB at 0x00000000f8c00000 [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000817fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x817ffe35c0-0x817ffe4d7f] [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000817fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000817fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000817fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 22 pages/cpu s52248 r8192 d29672 u90112 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1531392 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS0,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0500 arm-smmu.disable_bypass=0console_msg_format=syslog earlycon ip=dhcp [ 0.000000] software IO TLB: mapped [mem 0xf4c00000-0xf8c00000] (64MB) [ 0.000000] Memory: 5991808K/6223872K available (11388K kernel code, 1378K rwdata, 4968K rodata, 1344K init, 377K bss, 199296K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 65536 Devices @8179880000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GIC: using LPI property table @0x0000008179830000 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using LPI pending table @0x0000008179840000 [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000002] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008257] Console: colour dummy device 80x25 [ 0.012764] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023182] pid_max: default: 32768 minimum: 301 [ 0.027861] Security Framework initialized [ 0.033537] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.045635] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.052852] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.059796] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.067840] ASID allocator initialised with 32768 entries [ 0.073319] rcu: Hierarchical SRCU implementation. [ 0.078333] Platform MSI: gic-its@6020000 domain created [ 0.083701] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.091582] EFI services will not be available. [ 0.096249] smp: Bringing up secondary CPUs ... [ 0.101088] Detected VIPT I-cache on CPU1 [ 0.101104] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.101112] GICv3: CPU1: using LPI pending table @0x0000008179850000 [ 0.101131] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.101442] Detected VIPT I-cache on CPU2 [ 0.101453] GICv3: CPU2: found redistributor 2 region 0:0x0000000006140000 [ 0.101460] GICv3: CPU2: using LPI pending table @0x0000008179860000 [ 0.101475] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.101764] Detected VIPT I-cache on CPU3 [ 0.101775] GICv3: CPU3: found redistributor 3 region 0:0x0000000006160000 [ 0.101782] GICv3: CPU3: using LPI pending table @0x0000008179870000 [ 0.101796] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.101830] smp: Brought up 1 node, 4 CPUs [ 0.177664] SMP: Total of 4 processors activated. [ 0.182398] CPU features: detected: GIC system register CPU interface [ 0.188874] CPU features: detected: 32-bit EL0 Support [ 0.194311] CPU: All CPU(s) started at EL2 [ 0.198446] alternatives: patching kernel code [ 0.203786] devtmpfs: initialized [ 0.208399] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.218229] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.225064] pinctrl core: initialized pinctrl subsystem [ 0.230922] DMI not present or invalid. [ 0.235131] NET: Registered protocol family 16 [ 0.239771] audit: initializing netlink subsys (disabled) [ 0.245272] audit: type=2000 audit(0.164:1): state=initialized audit_enabled=0 res=1 [ 0.253089] cpuidle: using governor menu [ 0.257165] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.264571] DMA: preallocated 256 KiB pool for atomic allocations [ 0.271159] Serial: AMBA PL011 UART driver [ 0.275948] Machine: LS1088A RDB Board [ 0.279722] SoC family: QorIQ LS1088A [ 0.283401] SoC ID: svr:0x87032010, Revision: 1.0 [ 0.295775] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.302745] cryptd: max_cpu_qlen set to 1000 [ 0.307394] ACPI: Interpreter disabled. [ 0.311678] vgaarb: loaded [ 0.314558] SCSI subsystem initialized [ 0.318561] usbcore: registered new interface driver usbfs [ 0.324114] usbcore: registered new interface driver hub [ 0.329477] usbcore: registered new device driver usb [ 0.334837] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.342232] i2c i2c-0: IMX I2C adapter registered [ 0.346966] i2c i2c-0: can't use DMA, using PIO instead. [ 0.352502] pps_core: LinuxPPS API ver. 1 registered [ 0.357498] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.366700] PTP clock support registered [ 0.370702] EDAC MC: Ver: 3.0.0 [ 0.374362] Advanced Linux Sound Architecture Driver Initialized. [ 0.380861] clocksource: Switched to clocksource arch_sys_counter [ 0.387080] VFS: Disk quotas dquot_6.6.0 [ 0.391052] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.398051] pnp: PnP ACPI: disabled [ 0.404764] OF: /thermal-zones/cpu-thermal/cooling-maps/map1: could not find phandle [ 0.412575] missing cooling_device property [ 0.416785] failed to build thermal zone cpu-thermal: -22 [ 0.422278] NET: Registered protocol family 2 [ 0.426986] IP idents hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.435690] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes) [ 0.443685] TCP established hash table entries: 65536 (order: 7, 524288 bytes) [ 0.451359] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.458728] TCP: Hash tables configured (established 65536 bind 65536) [ 0.465366] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.471622] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.478342] NET: Registered protocol family 1 [ 0.483007] RPC: Registered named UNIX socket transport module. [ 0.488965] RPC: Registered udp transport module. [ 0.493702] RPC: Registered tcp transport module. [ 0.498429] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.505014] Unpacking initramfs... [ 0.978013] Freeing initrd memory: 14876K [ 0.982369] kvm [1]: 8-bit VMID [ 0.985826] kvm [1]: vgic-v2@c0e0000 [ 0.989432] kvm [1]: GIC system register CPU interface enabled [ 0.995384] kvm [1]: vgic interrupt IRQ1 [ 0.999386] kvm [1]: Hyp mode initialized successfully [ 1.006259] Initialise system trusted keyrings [ 1.010817] workingset: timestamp_bits=44 max_order=21 bucket_order=0 [ 1.021166] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.027382] NFS: Registering the id_resolver key type [ 1.032492] Key type id_resolver registered [ 1.036698] Key type id_legacy registered [ 1.040736] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.047480] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.055008] 9p: Installing v9fs 9p2000 file system support [ 1.062281] Key type asymmetric registered [ 1.066407] Asymmetric key parser 'x509' registered [ 1.071343] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 1.078789] io scheduler noop registered [ 1.082735] io scheduler deadline registered [ 1.087135] io scheduler cfq registered (default) [ 1.091865] io scheduler mq-deadline registered [ 1.096426] io scheduler kyber registered [ 1.103291] layerscape-pcie 3400000.pcie: host bridge /soc/pcie@3400000 ranges: [ 1.110670] layerscape-pcie 3400000.pcie: IO 0x2000010000..0x200001ffff -> 0x00000000 [ 1.118821] layerscape-pcie 3400000.pcie: MEM 0x2040000000..0x207fffffff -> 0x40000000 [ 1.127070] layerscape-pcie 3400000.pcie: PCI host bridge to bus 0000:00 [ 1.133821] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.139343] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.145566] pci_bus 0000:00: root bus resource [mem 0x2040000000-0x207fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.157085] pci 0000:00:00.0: BAR 1: assigned [mem 0x2040000000-0x2043ffffff] [ 1.164274] pci 0000:00:00.0: BAR 0: assigned [mem 0x2044000000-0x2044ffffff] [ 1.171467] pci 0000:00:00.0: BAR 6: assigned [mem 0x2045000000-0x2045ffffff pref] [ 1.179088] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.184413] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 1.191782] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x00000000 [ 1.199930] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x40000000 [ 1.208154] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0001:00 [ 1.214908] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.220432] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 1.229456] pci_bus 0001:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.242062] pci 0001:00:00.0: BAR 14: assigned [mem 0x3040000000-0x30400fffff] [ 1.249339] pci 0001:00:00.0: BAR 13: assigned [io 0x10000-0x10fff] [ 1.255737] pci 0001:00:00.0: BAR 6: assigned [mem 0x3040100000-0x30401007ff pref] [ 1.263362] pci 0001:01:00.0: BAR 1: assigned [mem 0x3040000000-0x304007ffff] [ 1.270558] pci 0001:01:00.0: BAR 6: assigned [mem 0x3040080000-0x30400bffff pref] [ 1.278177] pci 0001:01:00.0: BAR 0: assigned [mem 0x30400c0000-0x30400dffff] [ 1.285377] pci 0001:01:00.0: BAR 3: assigned [mem 0x30400e0000-0x30400e3fff] [ 1.292579] pci 0001:01:00.0: BAR 2: assigned [io 0x10000-0x1001f] [ 1.298906] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 1.304166] pci 0001:00:00.0: bridge window [io 0x10000-0x10fff] [ 1.310479] pci 0001:00:00.0: bridge window [mem 0x3040000000-0x30400fffff] [ 1.318117] EINJ: ACPI disabled. [ 1.325177] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.332598] console [ttyS0] disabled [ 1.336220] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 7, base_baud = 21875000) is a 16550A [ 1.344989] console [ttyS0] enabled [ 1.344989] console [ttyS0] enabled [ 1.351978] bootconsole [uart8250] disabled [ 1.351978] bootconsole [uart8250] disabled [ 1.360640] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 7, base_baud = 21875000) is a 16550A [ 1.369621] SuperH (H)SCI(F) driver initialized [ 1.374305] msm_serial: driver initialized [ 1.378780] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 1.388109] loop: module loaded [ 1.392146] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.401117] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.411552] scsi host0: ahci-qoriq [ 1.415137] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 15 [ 1.424288] tun: Universal TUN/TAP device driver, 1.6 [ 1.429707] thunder_xcv, ver 1.0 [ 1.432964] thunder_bgx, ver 1.0 [ 1.436206] nicpf, ver 1.0 [ 1.439083] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 1.444914] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.451245] e1000e 0001:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.517308] e1000e 0001:01:00.0 0001:01:00.0 (uninitialized): registered PHC clock [ 1.586820] e1000e 0001:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:1b:21:39:54:35 [ 1.594741] e1000e 0001:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 1.601626] e1000e 0001:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E42641-005 [ 1.608366] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 1.615326] igb: Copyright (c) 2007-2014 Intel Corporation. [ 1.620921] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 1.628750] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 1.634823] sky2: driver version 1.30 [ 1.638777] VFIO - User Level meta-driver version: 0.3 [ 1.644164] dwc3 3100000.usb3: Failed to get clk 'ref': -2 [ 1.650082] dwc3 3110000.usb3: Failed to get clk 'ref': -2 [ 1.656268] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.662799] ehci-pci: EHCI PCI platform driver [ 1.667261] ehci-platform: EHCI generic platform driver [ 1.672525] ehci-orion: EHCI orion driver [ 1.676570] ehci-exynos: EHCI EXYNOS driver [ 1.680784] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.686968] ohci-pci: OHCI PCI platform driver [ 1.691430] ohci-platform: OHCI generic platform driver [ 1.696691] ohci-exynos: OHCI EXYNOS driver [ 1.701048] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.706540] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 1.714464] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 1.723890] xhci-hcd xhci-hcd.0.auto: irq 13, io mem 0x03100000 [ 1.730234] hub 1-0:1.0: USB hub found [ 1.734008] hub 1-0:1.0: 1 port detected [ 1.734986] ata1: SATA link down (SStatus 0 SControl 300) [ 1.738095] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 1.748815] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 1.756474] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 1.763039] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.771402] hub 2-0:1.0: USB hub found [ 1.775167] hub 2-0:1.0: 1 port detected [ 1.779297] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.784791] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 1.792703] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 1.802123] xhci-hcd xhci-hcd.1.auto: irq 14, io mem 0x03110000 [ 1.808379] hub 3-0:1.0: USB hub found [ 1.812149] hub 3-0:1.0: 1 port detected [ 1.816219] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 1.821708] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 1.829369] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 1.835934] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.844288] hub 4-0:1.0: USB hub found [ 1.848051] hub 4-0:1.0: 1 port detected [ 1.852301] usbcore: registered new interface driver usb-storage [ 1.859446] i2c /dev entries driver [ 1.864269] i2c i2c-0: Added multiplexed i2c bus 1 [ 1.869158] i2c i2c-0: Added multiplexed i2c bus 2 [ 1.874130] i2c i2c-0: Added multiplexed i2c bus 3 [ 1.879149] i2c i2c-0: Added multiplexed i2c bus 4 [ 1.884045] i2c i2c-0: Added multiplexed i2c bus 5 [ 1.888947] i2c i2c-0: Added multiplexed i2c bus 6 [ 1.893834] i2c i2c-0: Added multiplexed i2c bus 7 [ 1.898724] i2c i2c-0: Added multiplexed i2c bus 8 [ 1.903517] pca954x 0-0077: registered 8 multiplexed busses for I2C mux pca9547 [ 1.911820] sp805-wdt c000000.wdt: registration successful [ 1.917411] sp805-wdt c010000.wdt: registration successful [ 1.922986] sp805-wdt c020000.wdt: registration successful [ 1.928563] sp805-wdt c030000.wdt: registration successful [ 1.934135] sp805-wdt c100000.wdt: registration successful [ 1.939705] sp805-wdt c110000.wdt: registration successful [ 1.945284] sp805-wdt c120000.wdt: registration successful [ 1.950858] sp805-wdt c130000.wdt: registration successful [ 1.957047] sdhci: Secure Digital Host Controller Interface driver [ 1.963225] sdhci: Copyright(c) Pierre Ossman [ 1.967704] Synopsys Designware Multimedia Card Interface Driver [ 1.974045] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.004874] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 2.013119] ledtrig-cpu: registered to indicate activity on CPUs [ 2.019688] usbcore: registered new interface driver usbhid [ 2.025258] usbhid: USB HID core driver [ 2.029860] optee: probing for conduit method from DT. [ 2.034998] optee: api uid mismatch [ 2.039084] NET: Registered protocol family 17 [ 2.043626] 9pnet: Installing 9P2000 support [ 2.047924] Key type dns_resolver registered [ 2.052492] registered taskstats version 1 [ 2.056592] Loading compiled-in X.509 certificates [ 2.062166] hctosys: unable to open rtc device (rtc0) [ 2.306105] mmc0: new high speed SDHC card at address e624 [ 2.312014] mmcblk0: mmc0:e624 ABLCD 29.7 GiB [ 2.320781] mmcblk0: p1 p2 p3 [ 4.681846] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 4.712868] Sending DHCP requests .., OK [ 9.516798] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.164 [ 9.524370] IP-Config: Complete: [ 9.527597] device=eth0, hwaddr=00:1b:21:39:54:35, ipaddr=172.16.1.164, mask=255.255.255.0, gw=172.16.1.4 [ 9.537598] host=172.16.1.164, domain=example.org, nis-domain=(none) [ 9.544382] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 9.544384] nameserver0=172.16.1.4 [ 9.554523] ALSA device list: [ 9.557488] No soundcards found. [ 9.561319] Freeing unused kernel memory: 1344K [ 9.580893] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 9.613663] udevd[1500]: starting version 3.2.9 [ 9.618601] random: udevd: uninitialized urandom read (16 bytes read) [ 9.625136] random: udevd: uninitialized urandom read (16 bytes read) [ 9.631612] random: udevd: uninitialized urandom read (16 bytes read) [ 9.640829] udevd[1500]: specified user 'tss' unknown [ 9.645930] udevd[1500]: specified group 'tss' unknown [ 9.651820] udevd[1501]: starting eudev-3.2.9 [ 9.732660] udevd[1511]: Error changing net interface name eth0 to enP1p1s0: Device or resource busy [ 9.742363] ina2xx 3-0040: power monitor ina220 (Rshunt = 1000 uOhm) [ 9.742621] lm90 4-004c: 4-004c supply vcc not found, using dummy regulator [ 9.749316] udevd[1511]: could not rename interface '2' from 'eth0' to 'enP1p1s0': Device or resource busy [ 9.755746] lm90 4-004c: Linked as a consumer to regulator.0 done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: [ 9.995257] NET: Registered protocol family 10 [ 10.000304] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1181543/environment . /lava-1181543/environment / # /lava-1181543/bin/lava-test-runner /lava-1181543/0 /lava-1181543/bin/lava-test-runner /lava-1181543/0 + export 'TESTRUN_[ 10.505878] ID=0_dmesg' + cd /lava-1181543/0/tests/0_dmesg + cat uuid + UUID=1181543_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/[ 10.521394] kernelci/dmesg.sh [ 10.539688] [ 10.556716] + [ 10.565650] set +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1181543/environment / # . /lava-1181543/environment/lava-1181543/bin/lava-test-runner /lava-1181543/1 / # /lava-1181543/bin/lava-test-runner /lava-1181543/1 + export 'TESTRUN_[ 10.997454] ID=1_bootrr' + cd /lava-1181543/1/tests/1_bootrr + cat uuid + UUID=1181543_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/hel[ 11.014411] pers:/lava-1181543/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + s[ 11.031204] h helpers/bootrr-auto /lava-1181543/1/../bin/lava-test-case /l[ 11.043291] ava-1181543/1/../bin/lava-test-case /lava-11815[ 11.054873] 43/1/../bin/lava-test-case + set +x / #