[Enter `^Ec?' for help]  U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.36 (8 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10664526/tftp-deploy-a5h3x95t/kernel/zImage tftp 0x10000000 10664526/tftp-deploy-a5h3x95t/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '10664526/tftp-deploy-a5h3x95t/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 11.1 MiB/s done Bytes transferred = 8737280 (855200 hex) => tftp 0x14000000 10664526/tftp-deploy-a5h3x95t/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10664526/tftp-deploy-a5h3x95t/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '10664526/tftp-deploy-a5h3x95t/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# 12.1 MiB/s done Bytes transferred = 13350123 (cbb4eb hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10664526/tftp-deploy-a5h3x95t/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10664526/tftp-deploy-a5h3x95t/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.36 Filename '10664526/tftp-deploy-a5h3x95t/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.6 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x855200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 13350059 Bytes = 12.7 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.284-cip99-rt31 (KernelCI@build-j16658-arm-gcc-10-multi-v7-defconfig-kgx9q) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Jun 9 17:09:07 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>[ 0.000000] Memory: 939108K/1048576K available (12288K kernel code, 1598K rwdata, 4684K rodata, 2048K init, 394K bss, 43932K reserved, 65536K cma-reserved, 196608K highmem) <5>[ 0.000000] Virtual kernel memory layout: <5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) <5>[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) <5>[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) <5>[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) <5>[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) <5>[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) <5>[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) <5>[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) <5>[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1599 kB) <5>[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008443] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.021413] Console: colour dummy device 80x30 <6>[ 0.023296] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.033714] pid_max: default: 32768 minimum: 301 <6>[ 0.038714] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.045458] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) <6>[ 0.053292] CPU: Testing write buffer coherency: ok <6>[ 0.057903] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.063561] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.069812] Setting up static identity map for 0x10300000 - 0x103000a0 <6>[ 0.077535] rcu: Hierarchical SRCU implementation. <6>[ 0.084277] EFI services will not be available. <6>[ 0.086527] smp: Bringing up secondary CPUs ... <6>[ 0.091909] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.091916] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.103241] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.103248] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.114443] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.114449] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.124784] smp: Brought up 1 node, 4 CPUs <6>[ 0.129039] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.135455] CPU: All CPU(s) started in SVC mode. <6>[ 0.141415] devtmpfs: initialized <6>[ 0.151137] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.156602] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.166342] futex hash table entries: 1024 (order: 4, 65536 bytes) <6>[ 0.175906] pinctrl core: initialized pinctrl subsystem <6>[ 0.180181] DMI not present or invalid. <6>[ 0.183473] NET: Registered protocol family 16 <6>[ 0.190797] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.197514] cpuidle: using governor menu <6>[ 0.199440] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.214360] vdd1p1: supplied by regulator-dummy <6>[ 0.216827] vdd3p0: supplied by regulator-dummy <6>[ 0.221558] vdd2p5: supplied by regulator-dummy <6>[ 0.226384] vddarm: supplied by regulator-dummy <6>[ 0.231295] vddpu: supplied by regulator-dummy <6>[ 0.235717] vddsoc: supplied by regulator-dummy <6>[ 0.254435] No ATAGs? <6>[ 0.254568] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.262522] hw-breakpoint: maximum watchpoint size is 4 bytes. <4>[ 0.271982] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory <6>[ 0.278855] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver <6>[ 0.290660] Serial: AMBA PL011 UART driver <6>[ 0.294503] console [pstore-1] enabled <6>[ 0.296333] pstore: Registered ramoops as persistent store backend <6>[ 0.302621] ramoops: attached 0x10000@0x30000000, ecc: 0/0 <6>[ 0.331316] mxs-dma 110000.dma-apbh: initialized <6>[ 0.340734] vgaarb: loaded <5>[ 0.341669] SCSI subsystem initialized <6>[ 0.345302] usbcore: registered new interface driver usbfs <6>[ 0.350632] usbcore: registered new interface driver hub <6>[ 0.356221] usbcore: registered new device driver usb <6>[ 0.362719] i2c i2c-0: IMX I2C adapter registered <6>[ 0.366434] i2c i2c-0: can't use DMA, using PIO instead. <6>[ 0.372576] i2c i2c-1: IMX I2C adapter registered <6>[ 0.376958] i2c i2c-1: can't use DMA, using PIO instead. <6>[ 0.382957] i2c i2c-2: IMX I2C adapter registered <6>[ 0.387490] i2c i2c-2: can't use DMA, using PIO instead. <6>[ 0.394572] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.398267] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.407692] PTP clock support registered <6>[ 0.412078] EDAC MC: Ver: 3.0.0 <6>[ 0.417943] clocksource: Switched to clocksource mxc_timer1 <6>[ 0.481326] NET: Registered protocol family 2 <6>[ 0.483525] IP idents hash table entries: 16384 (order: 5, 131072 bytes) <6>[ 0.491088] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) <6>[ 0.498039] TCP established hash table entries: 8192 (order: 3, 32768 bytes) <6>[ 0.505355] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) <6>[ 0.512133] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 0.518818] UDP hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.524810] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>[ 0.531579] NET: Registered protocol family 1 <6>[ 0.536579] RPC: Registered named UNIX socket transport module. <6>[ 0.542196] RPC: Registered udp transport module. <6>[ 0.547128] RPC: Registered tcp transport module. <6>[ 0.552100] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.559269] Trying to unpack rootfs image as initramfs... <6>[ 1.677589] Freeing initrd memory: 13040K <4>[ 1.679513] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 1.686722] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 1.696749] Initialise system trusted keyrings <6>[ 1.699757] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 1.712337] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.716311] NFS: Registering the id_resolver key type <5>[ 1.720950] Key type id_resolver registered <5>[ 1.725326] Key type id_legacy registered <6>[ 1.729646] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 1.736464] Key type asymmetric registered <5>[ 1.738580] Asymmetric key parser 'x509' registered <6>[ 1.743732] bounce: pool size: 64 pages <6>[ 1.747826] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.755449] io scheduler noop registered <6>[ 1.759618] io scheduler deadline registered <6>[ 1.764356] io scheduler cfq registered (default) <6>[ 1.769107] io scheduler mq-deadline registered <6>[ 1.773875] io scheduler kyber registered <6>[ 1.799814] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 1.804371] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 1.811497] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 1.818795] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 1.838862] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set <6>[ 1.842253] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc <4>[ 1.850104] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set <6>[ 1.856298] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 <4>[ 1.864216] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <4>[ 1.867977] PU : no governor for states <6>[ 1.873799] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 1.877874] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc <6>[ 1.951014] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.958362] SuperH (H)SCI(F) driver initialized <6>[ 1.961201] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX <6>[ 1.969977] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX <6>[ 1.980941] console [ttymxc1] enabled <6>[ 1.980941] console [ttymxc1] enabled <6>[ 1.985924] bootconsole [ec_imx21] disabled <6>[ 1.985924] bootconsole [ec_imx21] disabled <6>[ 1.996009] msm_serial: driver initialized <6>[ 2.002285] STMicroelectronics ASC driver initialized <6>[ 2.009446] STM32 USART driver initialized <4>[ 2.024448] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.033141] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.040153] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.046911] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.055955] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.063125] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.077883] brd: module loaded <6>[ 2.090747] loop: module loaded <6>[ 2.097354] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 2.105581] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 2.113874] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 2.122341] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <6>[ 2.133142] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 2.140428] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 2.149501] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 2.160310] scsi host0: ahci-imx <6>[ 2.164376] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 <6>[ 2.183478] CAN device driver interface <6>[ 2.188892] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <4>[ 2.195936] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator <6>[ 2.204906] fec 2188000.ethernet: Linked as a consumer to regulator.0 <6>[ 2.214016] pps pps0: new PPS source ptp0 <6>[ 2.244983] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 2.252369] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k <6>[ 2.258490] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 2.264730] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k <6>[ 2.271974] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 2.283640] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 2.291366] usbcore: registered new interface driver pegasus <6>[ 2.297332] usbcore: registered new interface driver asix <6>[ 2.303051] usbcore: registered new interface driver ax88179_178a <6>[ 2.309458] usbcore: registered new interface driver cdc_ether <6>[ 2.315609] usbcore: registered new interface driver smsc75xx <6>[ 2.321689] usbcore: registered new interface driver smsc95xx <6>[ 2.327731] usbcore: registered new interface driver net1080 <6>[ 2.333707] usbcore: registered new interface driver cdc_subset <6>[ 2.339942] usbcore: registered new interface driver zaurus <6>[ 2.345853] usbcore: registered new interface driver cdc_ncm <6>[ 2.354704] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 2.361533] ehci-pci: EHCI PCI platform driver <6>[ 2.366285] ehci-platform: EHCI generic platform driver <6>[ 2.372080] ehci-orion: EHCI orion driver <6>[ 2.376582] SPEAr-ehci: EHCI SPEAr driver <6>[ 2.381068] ehci-st: EHCI STMicroelectronics driver <6>[ 2.386403] ehci-exynos: EHCI EXYNOS driver <6>[ 2.391064] ehci-atmel: EHCI Atmel driver <6>[ 2.395516] tegra-ehci: Tegra EHCI driver <6>[ 2.400023] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 2.406484] ohci-pci: OHCI PCI platform driver <6>[ 2.411253] ohci-platform: OHCI generic platform driver <6>[ 2.417001] SPEAr-ohci: OHCI SPEAr driver <6>[ 2.421479] ohci-st: OHCI STMicroelectronics driver <6>[ 2.426806] ohci-atmel: OHCI Atmel driver <6>[ 2.432090] usbcore: registered new interface driver usb-storage <6>[ 2.440645] imx_usb 2184000.usb: Linked as a consumer to regulator.9 <6>[ 2.452678] imx_usb 2184200.usb: Linked as a consumer to regulator.14 <6>[ 2.462863] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 2.468063] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 2.497980] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 2.499421] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 2.509369] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 2.515906] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 2.523674] hub 1-0:1.0: USB hub found <6>[ 2.527730] hub 1-0:1.0: 1 port detected <6>[ 2.538234] i2c /dev entries driver <6>[ 2.556350] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) <6>[ 2.567812] sdhci: Secure Digital Host Controller Interface driver <6>[ 2.574286] sdhci: Copyright(c) Pierre Ossman <6>[ 2.581168] Synopsys Designware Multimedia Card Interface Driver <6>[ 2.589457] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 2.596245] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO <6>[ 2.601707] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO <6>[ 2.607203] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.647090] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA <6>[ 2.655135] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO <6>[ 2.660669] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 <6>[ 2.698167] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA <6>[ 2.709647] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 2.716721] usbcore: registered new interface driver usbhid <6>[ 2.722585] usbhid: USB HID core driver <6>[ 2.732632] NET: Registered protocol family 10 <6>[ 2.738507] Segment Routing with IPv6 <6>[ 2.742510] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 2.749269] NET: Registered protocol family 17 <6>[ 2.752192] mmc0: new high speed SDHC card at address aaaa <6>[ 2.753990] can: controller area network core (rev 20170425 abi 9) <6>[ 2.761467] mmcblk0: mmc0:aaaa SL16G 14.8 GiB <6>[ 2.766307] NET: Registered protocol family 29 <6>[ 2.775672] can: raw protocol (rev 20170425) <6>[ 2.780235] can: broadcast manager protocol (rev 20170425 t) <4>[ 2.784030] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 2.786171] can: netlink gateway (rev 20170425) max_hops=1 <4>[ 2.793856] GPT:7812499 != 31116287 <5>[ 2.800072] Key type dns_resolver registered <4>[ 2.803356] GPT:Alternate GPT header not at the end of the disk. <4>[ 2.814174] GPT:7812499 != 31116287 <6>[ 2.815096] cpu cpu0: Linked as a consumer to regulator.4 <4>[ 2.817944] GPT: Use GNU Parted to correct GPT errors. <6>[ 2.818004] mmcblk0: p1 p2 p3 <6>[ 2.823683] cpu cpu0: Linked as a consumer to regulator.5 <6>[ 2.838102] cpu cpu0: Linked as a consumer to regulator.6 <6>[ 2.844599] ThumbEE CPU extension supported. <5>[ 2.849221] Registering SWP/SWPB emulation handler <5>[ 2.854810] Loading compiled-in X.509 certificates <6>[ 2.861363] pstore: Using compression: deflate <6>[ 2.881801] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.889262] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.898118] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 2.905603] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 2.914570] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 2.918005] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 2.923265] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 2.936881] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 2.945007] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 2.954043] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 2.961203] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 2.970117] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <6>[ 2.981609] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 2.989173] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 2.997469] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.004954] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.013526] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.022206] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.029161] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.036954] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.046001] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.053141] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.060894] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.068291] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.076429] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.083906] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.092434] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.101113] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.108089] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.115859] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.124881] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.132071] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.139240] hub 1-1:1.0: USB hub found <6>[ 3.140498] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 <6>[ 3.143394] hub 1-1:1.0: 3 ports detected <6>[ 3.150219] hctosys: unable to open rtc device (rtc0) <6>[ 3.160692] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 3.168161] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 3.176854] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 3.184354] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 3.193027] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 3.201723] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 3.208695] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 3.216527] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 3.225563] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 3.232718] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 3.278900] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 3.293757] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready <6>[ 6.398618] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 6.417976] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 6.448021] Sending DHCP requests ., OK <6>[ 6.492174] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.36 <6>[ 6.500518] IP-Config: Complete: <6>[ 6.504035] device=eth0, hwaddr=00:19:b8:08:f1:1c, ipaddr=192.168.201.36, mask=255.255.255.0, gw=192.168.201.1 <6>[ 6.514783] host=imx6q-sabrelite-lava-cbg-6, domain=lava-rack, nis-domain=(none) <6>[ 6.522924] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 6.522932] nameserver0=192.168.201.1 <6>[ 6.541821] Freeing unused kernel memory: 2048K <6>[ 6.568306] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 6.699721] udevd[112]: starting version 3.2.9 <5>[ 6.705248] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.712621] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 6.719542] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 6.734182] udevd[112]: specified user 'tss' unknown <27>[ 6.739728] udevd[112]: specified group 'tss' unknown <30>[ 6.747088] udevd[113]: starting eudev-3.2.9 <6>[ 7.081353] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 <6>[ 7.089095] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) <6>[ 7.090074] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.104807] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.113803] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.114303] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.124710] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.136402] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <4>[ 7.137186] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.144831] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 7.151884] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.158657] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 7.165688] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.180182] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.189289] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.196520] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.204791] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.212228] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.237259] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 7.264413] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 7.270863] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 7.288004] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 <6>[ 7.296762] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.314695] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <6>[ 7.322262] sgtl5000 0-000a: Linked as a consumer to regulator.7 <6>[ 7.328927] sgtl5000 0-000a: Linked as a consumer to regulator.8 <4>[ 7.336546] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.342026] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 7.345408] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.357540] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.366279] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.375372] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.382744] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.391155] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.398605] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.402250] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <6>[ 7.407306] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.421194] pwm-backlight backlight-lvds: Dropping the link to regulator.8 <4>[ 7.471773] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator <6>[ 7.480569] panel-simple panel-lcd: Linked as a consumer to regulator.0 <6>[ 7.489383] panel-simple panel-lcd: Dropping the link to regulator.0 <4>[ 7.498525] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator <6>[ 7.509598] panel-simple panel-lvds0: Linked as a consumer to regulator.0 <6>[ 7.522504] panel-simple panel-lvds0: Dropping the link to regulator.0 <6>[ 7.531214] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 <6>[ 7.538942] pwm-backlight backlight-lcd: Dropping the link to regulator.8 <6>[ 7.548467] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 <6>[ 7.556097] pwm-backlight backlight-lvds: Dropping the link to regulator.8 done Saving random seed: <5>[ 7.895655] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 7.991337] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10664526/environment . /lava-10664526/environment / # /lava-10664526/bin/lava-test-runner /lava-10664526/0 /lava-10664526/bin/lava-test-runner /lava-10664526/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-10664526/0/tests/0_dmesg + cat uuid + <8>[ 8.592142] UUID=10664526_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 8.635924] <8>[ 8.676267] <8>[ 8.716752] + set +x <8>[ 8.726620] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10664526/environment / # . /lava-10664526/environment/lava-10664526/bin/lava-test-runner /lava-10664526/1 / # /lava-10664526/bin/lava-test-runner /lava-10664526/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-10664526/1/tests/1_bootrr + cat uuid + UUID=1066452<8>[ 9.230532] 6_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10664526/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lcd panel-lvds0 backlight-lcd backlight-lvds /lava-10664526/1/../bin/lava-test-case <8>[ 10.313941] /lava-10664526/1/../bin/lava-test-case <8>[ 10.353365] /lava-10664526/1/../bin/lava-test-case <8>[ 10.378263] + set +x <8>[ 10.396847] / #