[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Couldn't find partition mmc 0:1 Error selecting device File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (5 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 10664528/tftp-deploy-qur4zy6u/kernel/zImage tftp 0x10000000 10664528/tftp-deploy-qur4zy6u/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10664528/tftp-deploy-qur4zy6u/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 10.3 MiB/s done Bytes transferred = 8737280 (855200 hex) => tftp 0x14000000 10664528/tftp-deploy-qur4zy6u/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 10664528/tftp-deploy-qur4zy6u/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10664528/tftp-deploy-qur4zy6u/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################### 11.4 MiB/s done Bytes transferred = 9418674 (8fb7b2 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 10664528/tftp-deploy-qur4zy6u/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 10664528/tftp-deploy-qur4zy6u/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '10664528/tftp-deploy-qur4zy6u/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 2.5 MiB/s done Bytes transferred = 41606 (a286 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10664528/extract-nfsrootfs-4skb18ko,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10664528/extract-nfsrootfs-4skb18ko,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x855200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 9418610 Bytes = 9 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d285 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.284-cip99-rt31 (KernelCI@build-j16658-arm-gcc-10-multi-v7-defconfig-kgx9q) (gcc version 10.2.1 20210110 (Debian 10.2.1-6)) #1 SMP Fri Jun 9 17:09:07 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] percpu: Embedded 17 pages/cpu s37004 r8192 d24436 u69632 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/10664528/extract-nfsrootfs-4skb18ko,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 942948K/1048576K available (12288K kernel code, 1598K rwdata, 4684K rodata, 2048K init, 394K bss, 40092K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (13280 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) (1599 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 395 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000024] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003085] Console: colour dummy device 80x30 [ 0.003130] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003147] pid_max: default: 32768 minimum: 301 [ 0.003286] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003310] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.003845] CPU: Testing write buffer coherency: ok [ 0.003874] CPU0: Spectre v2: using BPIALL workaround [ 0.004242] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.004945] Setting up static identity map for 0x10300000 - 0x103000a0 [ 0.006559] rcu: Hierarchical SRCU implementation. [ 0.009944] EFI services will not be available. [ 0.010251] smp: Bringing up secondary CPUs ... [ 0.011170] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.011176] CPU1: Spectre v2: using BPIALL workaround [ 0.012190] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.012196] CPU2: Spectre v2: using BPIALL workaround [ 0.013190] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.013197] CPU3: Spectre v2: using BPIALL workaround [ 0.013305] smp: Brought up 1 node, 4 CPUs [ 0.013317] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.013325] CPU: All CPU(s) started in SVC mode. [ 0.014374] devtmpfs: initialized [ 0.021663] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022034] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022056] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.025188] pinctrl core: initialized pinctrl subsystem [ 0.026845] DMI not present or invalid. [ 0.027732] NET: Registered protocol family 16 [ 0.031371] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033716] cpuidle: using governor menu [ 0.033905] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.043751] vdd1p1: supplied by regulator-dummy [ 0.044268] vdd3p0: supplied by regulator-dummy [ 0.044749] vdd2p5: supplied by regulator-dummy [ 0.045256] vddarm: supplied by regulator-dummy [ 0.045909] vddpu: supplied by regulator-dummy [ 0.046292] vddsoc: supplied by regulator-dummy [ 0.060605] No ATAGs? [ 0.060755] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.060769] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.064178] imx6q-pinctrl 20e0000.iomuxc: Failed to create dummy-iomuxc-gpr@20e0000 debugfs directory [ 0.064417] imx6q-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver [ 0.069590] Serial: AMBA PL011 UART driver [ 0.071874] console [pstore-1] enabled [ 0.072054] pstore: Registered ramoops as persistent store backend [ 0.072067] ramoops: attached 0x10000@0x30000000, ecc: 0/0 [ 0.094956] mxs-dma 110000.dma-apbh: initialized [ 0.102399] vgaarb: loaded [ 0.103229] SCSI subsystem initialized [ 0.103661] usbcore: registered new interface driver usbfs [ 0.103717] usbcore: registered new interface driver hub [ 0.103770] usbcore: registered new device driver usb [ 0.105031] i2c i2c-0: IMX I2C adapter registered [ 0.105053] i2c i2c-0: can't use DMA, using PIO instead. [ 0.105612] i2c i2c-1: IMX I2C adapter registered [ 0.105632] i2c i2c-1: can't use DMA, using PIO instead. [ 0.106041] i2c i2c-2: IMX I2C adapter registered [ 0.106065] i2c i2c-2: can't use DMA, using PIO instead. [ 0.107581] pps_core: LinuxPPS API ver. 1 registered [ 0.107593] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.107616] PTP clock support registered [ 0.107861] EDAC MC: Ver: 3.0.0 [ 0.110692] clocksource: Switched to clocksource mxc_timer1 [ 0.170757] NET: Registered protocol family 2 [ 0.171216] IP idents hash table entries: 16384 (order: 5, 131072 bytes) [ 0.172219] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.172263] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.172356] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.172512] TCP: Hash tables configured (established 8192 bind 8192) [ 0.172725] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.172778] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.172949] NET: Registered protocol family 1 [ 0.173536] RPC: Registered named UNIX socket transport module. [ 0.173550] RPC: Registered udp transport module. [ 0.173560] RPC: Registered tcp transport module. [ 0.173570] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.174031] Trying to unpack rootfs image as initramfs... [ 0.894123] Freeing initrd memory: 9200K [ 0.894610] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.894952] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.896938] Initialise system trusted keyrings [ 0.897211] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 0.903423] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.904157] NFS: Registering the id_resolver key type [ 0.904199] Key type id_resolver registered [ 0.904210] Key type id_legacy registered [ 0.904259] ntfs: driver 2.1.32 [Flags: R/O]. [ 0.906377] Key type asymmetric registered [ 0.906392] Asymmetric key parser 'x509' registered [ 0.906445] bounce: pool size: 64 pages [ 0.906495] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.906510] io scheduler noop registered [ 0.906522] io scheduler deadline registered [ 0.906758] io scheduler cfq registered (default) [ 0.906774] io scheduler mq-deadline registered [ 0.906787] io scheduler kyber registered [ 0.928466] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 0.928581] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 0.928748] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 0.928803] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 0.941919] imx-pgc-pd imx-pgc-power-domain.0: DMA mask not set [ 0.941991] imx-pgc-pd imx-pgc-power-domain.0: Linked as a consumer to 20dc000.gpc [ 0.942048] imx-pgc-pd imx-pgc-power-domain.1: DMA mask not set [ 0.942135] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to regulator.5 [ 0.942281] PU : no governor for states [ 0.942308] imx-pgc-pd imx-pgc-power-domain.1: Linked as a consumer to 20dc000.gpc [ 0.942372] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 0.942392] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 0.996745] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.000304] SuperH (H)SCI(F) driver initialized [ 1.001257] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 27, base_baud = 5000000) is a IMX [ 1.002030] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 74, base_baud = 5000000) is a IMX [ 1.909466] console [ttymxc1] enabled [ 1.914364] msm_serial: driver initialized [ 1.918718] STMicroelectronics ASC driver initialized [ 1.925624] STM32 USART driver initialized [ 1.940295] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 1.948738] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 1.955453] panel-simple panel-lcd: Dropping the link to regulator.0 [ 1.961969] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 1.970738] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 1.977616] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 1.992307] brd: module loaded [ 2.004763] loop: module loaded [ 2.011143] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.019075] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.027108] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.035310] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.045838] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.052864] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.061679] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.072235] scsi host0: ahci-imx [ 2.076048] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 77 [ 2.094808] CAN device driver interface [ 2.099885] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.106731] fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator [ 2.115466] fec 2188000.ethernet: Linked as a consumer to regulator.0 [ 2.124298] pps pps0: new PPS source ptp0 [ 2.146472] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.153600] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k [ 2.159440] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.165443] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k [ 2.172428] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.183902] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.191363] usbcore: registered new interface driver pegasus [ 2.197075] usbcore: registered new interface driver asix [ 2.202552] usbcore: registered new interface driver ax88179_178a [ 2.208685] usbcore: registered new interface driver cdc_ether [ 2.214584] usbcore: registered new interface driver smsc75xx [ 2.220377] usbcore: registered new interface driver smsc95xx [ 2.226177] usbcore: registered new interface driver net1080 [ 2.231899] usbcore: registered new interface driver cdc_subset [ 2.237855] usbcore: registered new interface driver zaurus [ 2.243515] usbcore: registered new interface driver cdc_ncm [ 2.252102] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.258638] ehci-pci: EHCI PCI platform driver [ 2.263163] ehci-platform: EHCI generic platform driver [ 2.268673] ehci-orion: EHCI orion driver [ 2.272930] SPEAr-ehci: EHCI SPEAr driver [ 2.277129] ehci-st: EHCI STMicroelectronics driver [ 2.282216] ehci-exynos: EHCI EXYNOS driver [ 2.286579] ehci-atmel: EHCI Atmel driver [ 2.290794] tegra-ehci: Tegra EHCI driver [ 2.295023] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.301240] ohci-pci: OHCI PCI platform driver [ 2.305734] ohci-platform: OHCI generic platform driver [ 2.311242] SPEAr-ohci: OHCI SPEAr driver [ 2.315451] ohci-st: OHCI STMicroelectronics driver [ 2.320522] ohci-atmel: OHCI Atmel driver [ 2.325530] usbcore: registered new interface driver usb-storage [ 2.333810] imx_usb 2184000.usb: Linked as a consumer to regulator.9 [ 2.345625] imx_usb 2184200.usb: Linked as a consumer to regulator.14 [ 2.355538] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 2.360446] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 2.390727] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 2.396825] hub 1-0:1.0: USB hub found [ 2.400619] hub 1-0:1.0: 1 port detected [ 2.410847] i2c /dev entries driver [ 2.412163] ata1: SATA link down (SStatus 0 SControl 300) [ 2.419781] ahci-imx 2200000.sata: no device found, disabling link. [ 2.426084] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 2.428775] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0) [ 2.444424] sdhci: Secure Digital Host Controller Interface driver [ 2.450612] sdhci: Copyright(c) Pierre Ossman [ 2.457232] Synopsys Designware Multimedia Card Interface Driver [ 2.465211] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.471756] sdhci-esdhc-imx 2198000.usdhc: Got CD GPIO [ 2.476929] sdhci-esdhc-imx 2198000.usdhc: Got WP GPIO [ 2.482187] sdhci-esdhc-imx 2198000.usdhc: Linked as a consumer to regulator.8 [ 2.521777] mmc0: SDHCI controller on 2198000.usdhc [2198000.usdhc] using ADMA [ 2.529534] sdhci-esdhc-imx 219c000.usdhc: Got CD GPIO [ 2.534815] sdhci-esdhc-imx 219c000.usdhc: Linked as a consumer to regulator.8 [ 2.574411] mmc1: SDHCI controller on 219c000.usdhc [219c000.usdhc] using ADMA [ 2.585724] ledtrig-cpu: registered to indicate activity on CPUs [ 2.592537] usbcore: registered new interface driver usbhid [ 2.598114] usbhid: USB HID core driver [ 2.607951] NET: Registered protocol family 10 [ 2.613606] Segment Routing with IPv6 [ 2.617374] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.623882] NET: Registered protocol family 17 [ 2.628342] can: controller area network core (rev 20170425 abi 9) [ 2.634619] NET: Registered protocol family 29 [ 2.639073] can: raw protocol (rev 20170425) [ 2.643372] can: broadcast manager protocol (rev 20170425 t) [ 2.649072] can: netlink gateway (rev 20170425) max_hops=1 [ 2.655047] Key type dns_resolver registered [ 2.660342] cpu cpu0: Linked as a consumer to regulator.4 [ 2.665834] cpu cpu0: Linked as a consumer to regulator.5 [ 2.671340] cpu cpu0: Linked as a consumer to regulator.6 [ 2.677534] ThumbEE CPU extension supported. [ 2.681890] Registering SWP/SWPB emulation handler [ 2.687199] Loading compiled-in X.509 certificates [ 2.693431] pstore: Using compression: deflate [ 2.694647] mmc0: new high speed SDHC card at address 59b4 [ 2.705727] mmcblk0: mmc0:59b4 SD 14.7 GiB [ 2.711446] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.716918] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 2.718570] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.725940] GPT:7812499 != 30863359 [ 2.734226] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.736230] GPT:Alternate GPT header not at the end of the disk. [ 2.740748] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 2.743444] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.749411] GPT:7812499 != 30863359 [ 2.757393] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.762779] GPT: Use GNU Parted to correct GPT errors. [ 2.762823] mmcblk0: p1 p2 p3 [ 2.766323] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.789549] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.797280] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.806070] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.812964] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.821368] imx_thermal tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 2.831550] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.838649] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.846690] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.853912] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.862226] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.870621] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.877342] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.884882] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.893643] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.900506] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.907997] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.915123] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.923026] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 2.930233] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 2.938469] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 2.946889] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 2.953603] panel-simple panel-lcd: Dropping the link to regulator.0 [ 2.960231] hub 1-1:1.0: USB hub found [ 2.961232] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 2.964137] hub 1-1:1.0: 3 ports detected [ 2.972751] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 2.983599] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 2.991430] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 2.998529] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 2.998532] input: gpio-keys as /devices/soc0/gpio-keys/input/input0 [ 3.011939] hctosys: unable to open rtc device (rtc0) [ 3.013012] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 3.024263] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 3.032786] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 3.041227] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 3.047928] panel-simple panel-lcd: Dropping the link to regulator.0 [ 3.055553] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 3.064321] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 3.071194] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 3.078641] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 3.085772] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 3.121726] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.136414] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 6.231385] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.260812] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.290843] Sending DHCP requests ., OK [ 6.334677] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 [ 6.342718] IP-Config: Complete: [ 6.345956] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 [ 6.356412] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) [ 6.364292] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.364301] nameserver0=192.168.201.1 [ 6.381072] Freeing unused kernel memory: 2048K [ 6.400984] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u2 [ 7.216378] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.224256] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.233155] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.241667] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.248532] flexcan 2090000.flexcan: Linked as a consumer to regulator.10 [ 7.255957] flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=35) [ 7.256197] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.271701] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.280491] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.281190] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.287453] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.301720] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.308955] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.309133] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.317415] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.329475] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.329775] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.338304] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.342962] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.351464] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.364237] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.372362] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.381181] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.388165] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.416819] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.444604] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.451916] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.459247] sgtl5000 0-000a: Linked as a consumer to regulator.7 [ 7.465450] sgtl5000 0-000a: Linked as a consumer to regulator.8 [ 7.472530] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.474970] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.480651] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.485859] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.495038] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.500831] [drm] Initialized etnaviv 1.2.0 20151214 for etnaviv on minor 0 [ 7.507507] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.521948] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.529588] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.530425] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.543315] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.551424] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.560163] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.567877] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.576797] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.584338] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.594011] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.602467] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.602548] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.616961] panel-simple panel-lcd: Dropping the link to regulator.0 [ 7.661697] panel-simple panel-lvds0: panel-lvds0 supply power not found, using dummy regulator [ 7.670562] panel-simple panel-lvds0: Linked as a consumer to regulator.0 [ 7.680627] panel-simple panel-lvds0: Dropping the link to regulator.0 [ 7.688495] pwm-backlight backlight-lcd: Linked as a consumer to regulator.8 [ 7.696406] pwm-backlight backlight-lcd: Dropping the link to regulator.8 [ 7.705331] pwm-backlight backlight-lvds: Linked as a consumer to regulator.8 [ 7.712700] pwm-backlight backlight-lvds: Dropping the link to regulator.8 [ 7.721669] panel-simple panel-lcd: panel-lcd supply power not found, using dummy regulator [ 7.730084] panel-simple panel-lcd: Linked as a consumer to regulator.0 [ 7.736881] panel-simple panel-lcd: Dropping the link to regulator.0 Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 8.812478] systemd[1]: System time before build time, advancing clock. [ 8.849381] cgroup: cgroup2: unknown option "memory_recursiveprot" [ 8.864336] systemd[1]: systemd 247.3-7+deb11u2 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 8.888540] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 8.923581] systemd[1]: Set hostname to . [ 9.702852] systemd[1]: Queued start job for default target Graphical Interface. [ 9.712158] random: systemd: uninitialized urandom read (16 bytes read) [ 9.718966] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 9.731375] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 9.740521] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. [ 9.781142] random: systemd: uninitialized urandom read (16 bytes read) [ 9.788923] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. [ 9.831168] random: systemd: uninitialized urandom read (16 bytes read) [ 9.839017] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 9.882080] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 9.921856] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. [ 9.961523] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.001512] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.013441] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. [ 10.051268] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. [ 10.081329] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. [ 10.120914] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. [ 10.151313] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 10.182060] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.252496] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 10.262792] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 10.302487] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 10.353559] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. [ 10.394844] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. [ 10.432294] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 10.471897] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 10.481128] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 10.493576] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 10.536808] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... [ 10.605372] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... [ 10.654447] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... [ 10.693877] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... [ 10.731334] random: systemd: uninitialized urandom read (16 bytes read) [ 10.741296] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... [ 10.796111] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 10.806032] random: systemd: uninitialized urandom read (16 bytes read) [ 10.816002] systemd[1]: Starting Journal Service... Starting Journal Service... [ 10.855738] random: systemd: uninitialized urandom read (16 bytes read) [ 10.866521] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... [ 10.904277] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... [ 10.944030] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... [ 10.995642] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. [ 11.041627] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. [ 11.082117] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. [ 11.141676] systemd[1]: modprobe@configfs.service: Succeeded. [ 11.148137] systemd[1]: Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module configfs. [ 11.181631] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... [ 11.470186] systemd-journald[169]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. [ 11.881679] random: systemd: uninitialized urandom read (16 bytes read) Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ 11.963465] random: systemd-journal: uninitialized urandom read (16 bytes read) [ 11.975877] random: systemd-journal: uninitialized urandom read (16 bytes read) [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Finished Coldplug All udev Devices. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ 12.390883] random: crng init done [ 12.394312] random: 48 urandom warning(s) missed due to ratelimiting [ OK ] Finished Load/Save Random Seed. [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Service. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... Starting Network Name Resolution... [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Started Network Name Resolution. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 4.19.284-cip99-rt31 #1 SMP Fri Jun 9 17:09:07 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10664528/extract-nfsrootfs-4skb18ko' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/10664528/extract-nfsrootfs-4skb18ko' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-10664528/environment . /lava-10664528/environment / # /lava-10664528/bin/lava-test-runner /lava-10664528/0 /lava-10664528/bin/lava-test-runner /lava-10664528/0 + export TESTRUN_ID=0_dmesg + cd /lava-10664528/0/tests/0_dmesg + cat uuid + UUID=10664528_1.6.2.4.1 + set +[ 26.408323] x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 26.506662] [ 26.568356] [ 26.637822] + set +x [ 26.647110] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-10664528/environment / # . /lava-10664528/environment/lava-10664528/bin/lava-test-runner /lava-10664528/1 / # /lava-10664528/bin/lava-test-runner /lava-10664528/1 + export TESTRUN_ID=1_bootrr + cd /lava-10664528/1/tests/1_bootrr + cat uuid + UUID=10664528_1.6.2.4.5 + set +[ 27.206038] x + export PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-10664528/1/../bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto panel-lvds0 backlight-lcd backlight-lvds panel-lcd /lava-10664528/1/../bin/lava-test-case [ 28.339314] /lava-10664528/1/../bin/lava-test-case [ 28.403017] /lava-10664528/1/../bin/lava-test-case [ 28.436859] + set +x [ 28.462864] / #