connecting to NetworkSerialPort(target=Target(name='meson-g12a-u200', env=None), name='USBSerialPort', state=, avail=True, host='nuc-2', port=56227, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t nuc-2:56227 connected to 192.168.0.2 (port 56227) Escape character: Ctrl-\ Type the escape character to get to the prompt. G12A:BL:583440:b596c7;FEAT:E0F83180:2000;POC:F;RCY:0;EMMC:0;READ:0;0.0; bl2_stage_init1 L0:00000000 L1:80000703 L2:00008067 L3:04000000 B2:00002000 B1:e0f83180 TE: 143637 BL2 Built : 21:12:49, Apr 28 2018. g12a g3a251ca - jenkins@walle02-sh Board ID = 1 Set cpu clk to 24M Set clk81 to 24M CPU clk: 1200 MHz Set clk81 to 166.6M Handler is not supported boot_device: 1 -s board id: 1 Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x004000, part: 0 fw parse done Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x004000, part: 0 Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x004000, part: 0 PIEI prepare done Cfg max: 4, cur: 1. Board id: 255. Force loop cfg DDR4 probe Set ddr clk to 912MHz Load ddrfw from eMMC, src: 0x00014200, des: 0xfffd0000, size: 0x00c000, part: 0 dfi pinmux init ac pinmux init Check phy result INFO : End of initialization INFO : End of read enable training INFO : End of fine write leveling INFO : End of read dq deskew training INFO : End of MPR read delay center optimization INFO : End of Write leveling coarse delay INFO : End of write delay center optimization INFO : End of read delay center optimization INFO : End of max read latency training INFO : Training has run successfully! 1D training succeed Load ddrfw from eMMC, src: 0x00020200, des: 0xfffd0000, size: 0x00c000, part: 0 Check phy result INFO : End of initialization INFO : End of 2D read delay Voltage center optimization INFO : End of 2D write delay Voltage center optimization INFO : Training has run successfully! R0_RxClkDly_Margin==205 R0_TxDqDly_Margi==222 R1_RxClkDly_Margin==0 R1_TxDqDly_Margi==0 PIEI init PIEI init cnt: 180 dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0001 2D training succeed DDR size: 2048MB DataBus test pass! AddrBus test pass! result report Enable ddr reg access 00000000 emmc switch 3 ok Authentication key not yet programmed emmc_rpmb_key_is_programmed: error 0x00000007 00000000 emmc switch 0 ok Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x004000, part: 0 Load BL3X from eMMC, src: 0x00064200, des: 0x01754000, size: 0x0b4000, part: 0 0.0;M3 CHK:0;cm4_sp_mode 0 [Image: g12a_v1.1.3310-81c9e20 2018-05-02 10:15:01 jenkins@walle02-sh] OPS=0x10 28 0a 10 00 6c 5f 6c 59 2d 41 32 31 47 4c 4d 41 This is ES chip bl30:This chip has not trimmed thermal!!! bl30: thermal cali data update error [0.020913 Inits done] secure task start! high task start! low task start! run into bl31 NOTICE: BL31: v1.3(release):debc425 NOTICE: BL31: Built : 14:06:49, May 3 2018 NOTICE: BL31: G12A normal boot! NOTICE: BL31: BL33 decompress pass ERROR: Error initializing runtime service opteed_fast U-Boot 2015.01-g784ee4d (May 04 2018 - 20:08:53) DRAM: 2 GiB Relocation Offset is: 76e83000 spi_post_bind(spifc): req_seq = 0 register usb cfg[0][1] = 0000000077f48578 NAND: get_sys_clk_rate_mtd() 266, clock setting 200! NAND device id: 0 7 ff ff ff ff No NAND device found!!! nand init failed: -6 get_sys_clk_rate_mtd() 266, clock setting 200! NAND device id: 0 7 ff ff ff ff No NAND device found!!! nand init failed: -6 MMC: aml_priv->desc_buf = 0x0000000073e73710 aml_priv->desc_buf = 0x0000000073e75a30 SDIO Port B: 0, SDIO Port C: 1 co-phase 0x2, tx-dly 0 co-phase 0x2, tx-dly 0 co-phase 0x2, tx-dly 0 emmc/sd response timeout, cmd8, status=0x1ff2800 emmc/sd response timeout, cmd55, status=0x1ff2800 co-phase 0x2, tx-dly 0 co-phase 0x2, tx-dly 0 init_part() 297: PART_TYPE_AML [mmc_init] mmc init success start dts,buffer=0000000073e78280,dt_addr=0000000073e78280 get_partition_from_dts() 105: ret 0 parts: 14 00: logo 0000000000800000 1 01: recovery 0000000001800000 1 02: misc 0000000000800000 1 03: dto 0000000000800000 1 04: cri_data 0000000000800000 2 05: param 0000000001000000 2 06: boot 0000000001000000 1 07: rsv 0000000001000000 1 08: tee 0000000002000000 1 09: vendor 0000000010000000 1 10: odm 0000000010000000 1 11: system 0000000074000000 1 12: cache 0000000046000000 2 13: data ffffffffffffffff 4 init_part() 297: PART_TYPE_AML eMMC/TSD partition table have been checked OK! check pattern success mmc env offset: 0x4d400000 In: serial Out: serial Err: serial reboot_mode=cold_boot [store]To run cmd[emmc dtb_read 0x1000000 0x40000] _verify_dtb_checksum()-2755: calc c2806ee9, store c2806ee9 _verify_dtb_checksum()-2755: calc c2806ee9, store c2806ee9 dtb_read()-2972: total valid 2 update_old_dtb()-2953: do nothing amlkey_init() enter! [EFUSE_MSG]keynum is 4 vpu: clk_level in dts: 7 vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100) vpu: vpu_clk_gate_init_off finish vpp: vpp_init vpp: g12a osd1 matrix rgb2yuv .............. vpp: g12a osd2 matrix rgb2yuv.............. vpp: g12a osd3 matrix rgb2yuv.............. aml_config_dtb 572 aml_config_dtb 574 co_phase = <0x00000002> libfdt fdt_getprop(): FDT_ERR_NOTFOUND f_max = <0x02625a00> status = \"okay\" status = \"okay\" drive-strength = <0x00000001> drive-strength = <0x00000001> drive-strength = <0x00000001> drive-strength = <0x00000001> drive-strength = <0x00000002> drive-strength = <0x00000001> Net: dwmac.ff3f0000amlkey_init() enter! amlkey_init() 71: already init! [EFUSE_MSG]keynum is 4 MACADDR:02:2d:59:6c:5f:6c(from chipid) Start read misc partition datas! info->attemp_times = 0 info->active_slot = 0 info->slot_info[0].bootable = 1 info->slot_info[0].online = 1 info->slot_info[1].bootable = 0 info->slot_info[1].online = 0 info->attemp_times = 0 attemp_times = 0 active slot = 0 wipe_data=successful wipe_cache=successful upgrade_step=0 [OSD]load fb addr from dts:/meson-fb [OSD]set initrd_high: 0x7f800000 [OSD]fb_addr for logo: 0x7f800000 [OSD]load fb addr from dts:/meson-fb [OSD]fb_addr for logo: 0x7f800000 [OSD]VPP_OFIFO_SIZE:0xfff01fff [CANVAS]canvas init [CANVAS]addr=0x7f800000 width=3840, height=2160 [OSD]osd_hw.free_dst_data: 0,1919,0,1079 [OSD]osd1_update_disp_freescale_enable [1080p60hz] is invalid for cvbs. set hdmitx VIC = 16 config HPLL = 4455000 HPLL: 0x3b0004b9 HPLL: 0x1b0004b9 HPLL: 0xdb0004b9 config HPLL done j = 6 vid_clk_div = 1 hdmitx phy setting done hdmitx: set enc for VIC: 16 enc_vpu_bridge_reset[1195] rx version is 1.4 or below div=10 amlkey_init() enter! amlkey_init() 71: already init! [EFUSE_MSG]keynum is 4 [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet [KM]Error:f[key_manage_query_size]L507:key[mac] not programed yet [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet Hit Enter or space or Ctrl+C key to stop autoboot -- : 1  0 g12a_u200_v1#setenv autoload no setenv autoload no g12a_u200_v1#setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff g12a_u200_v1#setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff g12a_u200_v1#dhcp dhcp dwmac.ff3f0000 Waiting for PHY auto negotiation to complete.. done Speed: 100, full duplex BOOTP broadcast 1 BOOTP broadcast 2 DHCP client bound to address 192.168.0.194 (262 ms) g12a_u200_v1#setenv serverip 192.168.0.2 setenv serverip 192.168.0.2 g12a_u200_v1#tftp 0x8080000 2462039/tftp-deploy-zg49h1r6/kernel/uImage tftp 0x8080000 2462039/tftp-deploy-zg49h1r6/kernel/uImage Speed: 100, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.194 Filename '2462039/tftp-deploy-zg49h1r6/kernel/uImage'. Load address: 0x8080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 1.9 MiB/s done Bytes transferred = 31836736 (1e5ca40 hex) g12a_u200_v1#tftp 0x13000000 2462039/tftp-deploy-zg49h1r6/ramdisk/ramdisk.cpio.gz.uboot tftp 0x13000000 2462039/tftp-deploy-zg49h1r6/ramdisk/ramdisk.cpio.gz.uboot Speed: 100, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.194 Filename '2462039/tftp-deploy-zg49h1r6/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x13000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 2 MiB/s done Bytes transferred = 18931904 (120e0c0 hex) g12a_u200_v1#setenv initrd_size ${filesize} setenv initrd_size ${filesize} g12a_u200_v1#tftp 0x8008000 2462039/tftp-deploy-zg49h1r6/dtb/meson-g12a-u200.dtb tftp 0x8008000 2462039/tftp-deploy-zg49h1r6/dtb/meson-g12a-u200.dtb Speed: 100, full duplex Using dwmac.ff3f0000 device TFTP from server 192.168.0.2; our IP address is 192.168.0.194 Filename '2462039/tftp-deploy-zg49h1r6/dtb/meson-g12a-u200.dtb'. Load address: 0x8008000 Loading: *#### 1.6 MiB/s done Bytes transferred = 46278 (b4c6 hex) g12a_u200_v1#setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' g12a_u200_v1#bootm 0x8080000 0x13000000 0x8008000 bootm 0x8080000 0x13000000 0x8008000 ee_gate_off ... ## Booting kernel from Legacy Image at 08080000 ... Image Name: Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 31836672 Bytes = 30.4 MiB Load Address: 08080000 Entry Point: 08080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 13000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18931840 Bytes = 18.1 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK load dtb from 0x1000000 ...... ## Flattened Device Tree blob at 08008000 Booting using the fdt blob at 0x8008000 Loading Kernel Image(COMP_NONE) ... OK kernel loaded at 0x08080000, end = 0x09edca00 libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND [rsvmem] fdt get prop fail. Loading Ramdisk to 72c63000, end 73e71080 ... OK Loading Device Tree to 0000000072c54000, end 0000000072c624c5 ... OK Starting kernel ... uboot time: 30530316 us [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.138-cip15 (KernelCI@build-j116758-arm64-gcc-10-defconfig-nckh2) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue Sep 6 00:16:51 UTC 2022 [ 0.000000] Machine model: Amlogic Meson G12A U200 Development Board [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000062c00000, size 256 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] earlycon: meson0 at MMIO 0x00000000ff803000 (options '115200n8') [ 0.000000] printk: bootconsole [meson0] enabled [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000000000000-0x0000000077ffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x77c05b00-0x77c07fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000077ffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000004ffffff] [ 0.000000] node 0: [mem 0x0000000005000000-0x00000000072fffff] [ 0.000000] node 0: [mem 0x0000000007300000-0x0000000077ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000077ffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] percpu: Embedded 23 pages/cpu s56600 r8192 d29416 u94208 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 483840 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: console=ttyAML0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 1577588K/1966080K available (14592K kernel code, 2802K rwdata, 7600K rodata, 5952K init, 512K bss, 126348K reserved, 262144K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GIC: Using split EOI/Deactivate mode <6>[ 0.000000] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized <6>[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns <6>[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns <6>[ 0.008615] Console: colour dummy device 80x25 <6>[ 0.013128] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) <6>[ 0.023632] pid_max: default: 32768 minimum: 301 <6>[ 0.028602] LSM: Security Framework initializing <6>[ 0.033488] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.041139] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 0.050739] rcu: Hierarchical SRCU implementation. <6>[ 0.058131] EFI services will not be available. <6>[ 0.059447] smp: Bringing up secondary CPUs ... <6>[ 0.064502] Detected VIPT I-cache on CPU1 <6>[ 0.064576] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.065118] Detected VIPT I-cache on CPU2 <6>[ 0.065148] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] <6>[ 0.065649] Detected VIPT I-cache on CPU3 <6>[ 0.065676] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] <6>[ 0.065734] smp: Brought up 1 node, 4 CPUs <6>[ 0.101692] SMP: Total of 4 processors activated. <6>[ 0.106671] CPU features: detected: 32-bit EL0 Support <6>[ 0.112112] CPU features: detected: CRC32 instructions <6>[ 0.117523] CPU features: detected: 32-bit EL1 Support <6>[ 0.130136] CPU: All CPU(s) started at EL2 <6>[ 0.130211] alternatives: patching kernel code <6>[ 0.134701] devtmpfs: initialized <4>[ 0.145254] KASLR disabled due to lack of seed <6>[ 0.145448] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.154403] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.168832] pinctrl core: initialized pinctrl subsystem <6>[ 0.170512] DMI not present or invalid. <6>[ 0.173453] NET: Registered protocol family 16 <6>[ 0.179128] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.184995] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.193083] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.201233] audit: initializing netlink subsys (disabled) <5>[ 0.206989] audit: type=2000 audit(0.148:1): state=initialized audit_enabled=0 res=1 <6>[ 0.208639] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.214898] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.221515] cpuidle: using governor menu <6>[ 0.232394] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.239397] ASID allocator initialised with 32768 entries <6>[ 0.246841] Serial: AMBA PL011 UART driver <6>[ 0.287153] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.288489] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.295502] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.302506] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.310494] cryptd: max_cpu_qlen set to 1000 <6>[ 0.316161] ACPI: Interpreter disabled. <3>[ 0.319486] reg-fixed-voltage regulator-flash_1v8: Failed to register regulator: -517 <3>[ 0.326606] reg-fixed-voltage regulator-vcc_1v8: Failed to register regulator: -517 <3>[ 0.334319] reg-fixed-voltage regulator-vcc_3v3: Failed to register regulator: -517 <3>[ 0.342334] reg-fixed-voltage regulator-vddao_1v8: Failed to register regulator: -517 <6>[ 0.350418] VDDAO_3V3: supplied by 12V <6>[ 0.355159] iommu: Default domain type: Translated <6>[ 0.359789] vgaarb: loaded <5>[ 0.362819] SCSI subsystem initialized <6>[ 0.366885] usbcore: registered new interface driver usbfs <6>[ 0.372362] usbcore: registered new interface driver hub <6>[ 0.377948] usbcore: registered new device driver usb <6>[ 0.383946] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.388505] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.397964] PTP clock support registered <6>[ 0.402265] EDAC MC: Ver: 3.0.0 <6>[ 0.407128] FPGA manager framework <6>[ 0.409320] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.416416] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.422232] VFS: Disk quotas dquot_6.6.0 <6>[ 0.426265] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.433577] pnp: PnP ACPI: disabled <6>[ 0.442556] NET: Registered protocol family 2 <6>[ 0.442758] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear) <6>[ 0.450396] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear) <6>[ 0.458375] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.466665] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear) <6>[ 0.474390] TCP: Hash tables configured (established 16384 bind 16384) <6>[ 0.481108] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 0.488042] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) <6>[ 0.495595] NET: Registered protocol family 1 <6>[ 0.500464] RPC: Registered named UNIX socket transport module. <6>[ 0.506308] RPC: Registered udp transport module. <6>[ 0.511269] RPC: Registered tcp transport module. <6>[ 0.516254] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.523002] PCI: CLS 0 bytes, default 64 <6>[ 0.527357] Unpacking initramfs... <6>[ 1.373126] Freeing initrd memory: 18488K <6>[ 1.373905] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.377551] kvm [1]: vgic interrupt IRQ9 <6>[ 1.380623] kvm [1]: Hyp mode initialized successfully <5>[ 1.389370] Initialise system trusted keyrings <6>[ 1.390809] workingset: timestamp_bits=42 max_order=19 bucket_order=0 <6>[ 1.403182] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.404261] NFS: Registering the id_resolver key type <5>[ 1.409022] Key type id_resolver registered <5>[ 1.413446] Key type id_legacy registered <6>[ 1.417812] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.424735] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.432594] 9p: Installing v9fs 9p2000 file system support <5>[ 1.473808] Key type asymmetric registered <5>[ 1.473832] Asymmetric key parser 'x509' registered <6>[ 1.477717] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.485382] io scheduler mq-deadline registered <6>[ 1.490196] io scheduler kyber registered <4>[ 1.506770] EINJ: ACPI disabled. <6>[ 1.518218] soc soc0: Amlogic Meson G12A (S905D2) Revision 28:a (10:2) Detected <6>[ 1.527482] Serial: 8250/16550 driver, 4 ports, IRQ sharing enable$6>[ 1.533832] ff803000.serial: ttyAML0 at MMIO 0xff803000 (irq = 19, base_baud = 1500000) is a meson_uart <6>[ 1.543555] printk: console [ttyAML0] enabled <6>[ 1.543555] printk: console [ttyAML0] enabled <6>[ 1.547113] printk: bootconsole [meson0] disabled <6>[ 1.547113] printk: bootconsole [meson0] disabled <6>[ 1.557607] msm_serial: driver initialized <6>[ 1.569559] loop: module loaded <6>[ 1.570526] megasas: 07.714.04.00-rc1 <6>[ 1.576818] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.577669] thunder_xcv, ver 1.0 <6>[ 1.579973] thunder_bgx, ver 1.0 <6>[ 1.583436] nicpf, ver 1.0 <6>[ 1.587477] hclge is initializing <6>[ 1.589893] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.597293] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.602851] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.607895] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.613877] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.619021] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.625176] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.630751] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.636557] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.642998] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.649447] sky2: driver version 1.30 <6>[ 1.654088] VFIO - User Level meta-driver version: 0.3 <6>[ 1.660331] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.665092] ehci-pci: EHCI PCI platform driver <6>[ 1.669768] ehci-platform: EHCI generic platform driver <6>[ 1.675294] ehci-orion: EHCI orion driver <6>[ 1.679487] ehci-exynos: EHCI Exynos driver <6>[ 1.683877] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.690204] ohci-pci: OHCI PCI platform driver <6>[ 1.694869] ohci-platform: OHCI generic platform driver <6>[ 1.700375] ohci-exynos: OHCI Exynos driver <6>[ 1.705172] usbcore: registered new interface driver usb-storage <6>[ 1.713342] i2c /dev entries driver <3>[ 1.720574] amlogic_thermal ff634800.temperature-sensor: tsensor thermal calibration not supported: 0x0! <4>[ 1.724743] amlogic_thermal: probe of ff634800.temperature-sensor failed with error -22 <3>[ 1.732971] amlogic_thermal ff634c00.temperature-sensor: tsensor thermal calibration not supported: 0x0! <4>[ 1.742545] amlogic_thermal: probe of ff634c00.temperature-sensor failed with error -22 <6>[ 1.753461] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.757104] sdhci: Copyright(c) Pierre Ossman <6>[ 1.762191] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.768913] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.769298] meson-gx-mmc ffe05000.sd: Got CD GPIO <6>[ 1.778727] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.785977] meson-sm: secure-monitor enabled <6>[ 1.790349] usbcore: registered new interface driver usbhid <6>[ 1.795128] usbhid: USB HID core driver <6>[ 1.804440] NET: Registered protocol family 17 <6>[ 1.804631] 9pnet: Installing 9P2000 support <5>[ 1.808376] Key type dns_resolver registered <6>[ 1.813143] registered taskstats version 1 <5>[ 1.817123] Loading compiled-in X.509 certificates <3>[ 1.836070] reg-fixed-voltage regulator-flash_1v8: Failed to register regulator: -517 <3>[ 1.841107] reg-fixed-voltage regulator-vcc_1v8: Failed to register regulator: -517 <6>[ 1.848169] VCC_3V3: supplied by VDDAO_3V3 <6>[ 1.851332] VCC_5V: supplied by 12V <6>[ 1.854700] VDDAO_1V8: supplied by VDDAO_3V3 <6>[ 1.858977] USB_PWR_EN: supplied by VCC_5V <6>[ 1.869032] dwc3-meson-g12a ffe09000.usb: USB2 ports: 2 <6>[ 1.869070] dwc3-meson-g12a ffe09000.usb: USB3 ports: 1 <4>[ 1.878717] dwc2 ff400000.usb: supply vusb_d not found, using dummy regulator <4>[ 1.881803] dwc2 ff400000.usb: supply vusb_a not found, using dummy regulator <6>[ 1.889254] dwc2 ff400000.usb: EPs: 7, dedicated fifos, 712 entries in SPRAM <6>[ 1.899075] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.901989] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 <6>[ 1.909925] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x0000000000010010 <6>[ 1.919408] xhci-hcd xhci-hcd.0.auto: irq 34, io mem 0xff500000 <6>[ 1.926257] hub 1-0:1.0: USB hub found <6>[ 1.929463] hub 1-0:1.0: 2 ports detected <6>[ 1.933944] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller <6>[ 1.939368] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 <6>[ 1.947214] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed <6>[ 1.953972] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. <6>[ 1.962664] hub 2-0:1.0: USB hub found <6>[ 1.966197] hub 2-0:1.0: 1 port detected <6>[ 1.970789] dwc3-meson-g12a ffe09000.usb: switching to Device Mode <6>[ 1.980237] FLASH_1V8: supplied by VCC_3V3 <6>[ 1.981771] VCC_1V8: supplied by VCC_3V3 <6>[ 1.982157] meson-gx-mmc ffe07000.mmc: allocated mmc-pwrseq <6>[ 2.159280] mmc1: new HS200 MMC card at address 0001 <6>[ 2.160058] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB <6>[ 2.163922] mmcblk1boot0: mmc1:0001 AJTD4R partition 1 4.00 MiB <6>[ 2.170028] mmcblk1boot1: mmc1:0001 AJTD4R partition 2 4.00 MiB <6>[ 2.176038] mmcblk1rpmb: mmc1:0001 AJTD4R partition 3 4.00 MiB, chardev (234:0) <6>[ 14.300653] ALSA device list: <6>[ 14.300691] No soundcards found. <6>[ 14.310010] Freeing unused kernel memory: 5952K <6>[ 14.310131] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 14.376374] udevd[171]: starting version 3.2.9 <5>[ 14.377206] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.382363] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 14.388871] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 14.399973] udevd[171]: specified user 'tss' unknown <27>[ 14.400858] udevd[171]: specified group 'tss' unknown <30>[ 14.407488] udevd[172]: starting eudev-3.2.9 <6>[ 14.721800] panfrost ffe40000.gpu: clock rate = 24000000 <3>[ 14.721917] panfrost ffe40000.gpu: dev_pm_opp_set_regulators: no regulator (mali) found: -19 <6>[ 14.732840] meson8b-dwmac ff3f0000.ethernet: IRQ eth_wake_irq not found <6>[ 14.756275] meson8b-dwmac ff3f0000.ethernet: IRQ eth_lpi not found <6>[ 14.760649] meson8b-dwmac ff3f0000.ethernet: PTP uses main clock <6>[ 14.763294] meson8b-dwmac ff3f0000.ethernet: no reset control found <6>[ 14.771668] panfrost ffe40000.gpu: [drm:panfrost_devfreq_init [panfrost]] Failed to register cooling device <6>[ 14.795865] meson8b-dwmac ff3f0000.ethernet: User ID: 0x11, Synopsys ID: 0x37 <6>[ 14.797891] panfrost ffe40000.gpu: mali-g31 id 0x7093 major 0x0 minor 0x0 status 0x0 <6>[ 14.803389] meson-vrtc ff8000a8.rtc: registered as rtc0 <6>[ 14.814274] meson8b-dwmac ff3f0000.ethernet: DWMAC1000 <6>[ 14.816746] meson8b-dwmac ff3f0000.ethernet: DMA HW capability register supported <6>[ 14.817567] meson-drm ff900000.vpu: Queued 3 outputs on vpu <6>[ 14.826190] panfrost ffe40000.gpu: features: 00000000,3fde77ff, issues: 00000000,00000400 <6>[ 14.838264] meson-vrtc ff8000a8.rtc: setting system clock to 1970-01-01T00:00:14 UTC (14) <6>[ 14.847265] meson8b-dwmac ff3f0000.ethernet: RX Checksum Offload Engine supported <6>[ 14.850677] VDDCPU: supplied by 12V <6>[ 14.871824] panfrost ffe40000.gpu: Features: L2:0x07100206 Shader:0x00000000 Tiler:0x00000209 Mem:0x1 MMU:0x00002821 AS:0xff JS:0x7 <6>[ 14.879542] panfrost ffe40000.gpu: shader_present=0x1 l2_present=0x1 <6>[ 14.884803] meson8b-dwmac ff3f0000.ethernet: COE Type 2 <6>[ 14.884808] meson8b-dwmac ff3f0000.ethernet: TX Checksum insertion supported <6>[ 14.908355] Registered IR keymap rc-empty <6>[ 14.910973] [drm] Initialized panfrost 1.1.0 20180908 for ffe40000.gpu on minor 0 <6>[ 14.911347] meson8b-dwmac ff3f0000.ethernet: Wake-Up On Lan supported <6>[ 14.921489] meson8b-dwmac ff3f0000.ethernet: Normal descriptors <6>[ 14.922001] rc rc0: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0 <6>[ 14.927547] meson8b-dwmac ff3f0000.ethernet: Ring mode enabled <6>[ 14.936205] input: meson-ir as /devices/platform/soc/ff800000.bus/ff808000.ir/rc/rc0/input0 <6>[ 14.941526] meson8b-dwmac ff3f0000.ethernet: Enable RX Mitigation via HW Watchdog Timer <6>[ 14.958765] meson-ir ff808000.ir: receiver initialized <6>[ 14.963689] meson-dw-hdmi ff600000.hdmi-tx: Detected HDMI TX controller v2.01a with HDCP (meson_dw_hdmi_phy) <6>[ 14.967926] meson-dw-hdmi ff600000.hdmi-tx: registered DesignWare HDMI I2C bus driver <6>[ 14.983204] meson-drm ff900000.vpu: bound ff600000.hdmi-tx (ops meson_dw_hdmi_ops [meson_dw_hdmi]) <6>[ 14.991304] [drm] Initialized meson 1.0.0 20161109 for ff900000.vpu on minor 1 <6>[ 15.020218] Console: switching to colour frame buffer device 90x36 <6>[ 15.044903] meson-drm ff900000.vpu: [drm] fb0: mesondrmfb frame buffer device done Saving random seed: OK Starting network: OK Starting dropbear sshd: <6>[ 15.164076] NET: Registered protocol family 10 <6>[ 15.165298] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-2462039/environment . /lava-2462039/environment / # /lava-2462039/bin/lava-test-runner /lava-2462039/0 /lava-2462039/bin/lava-test-runner /lava-2462039/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-2462039/0/tests/0_dmesg + cat uuid + UUID=2462039_1.5.2.4.<8>[ 15.714679] 1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.738946] <8>[ 15.758005] <8>[ 15.777143] + set +x <8>[ 15.781588] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-2462039/environment / # . /lava-2462039/environment/lava-2462039/bin/lava-test-runner /lava-2462039/1 / # /lava-2462039/bin/lava-test-runner /lava-2462039/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-2462039/1/tests/1_bootrr + cat uuid + UUID=2462039_1.5.2<8>[ 16.249218] .4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-2462039/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-2462039/1/../bin/lava-test-case <8>[ 17.277472] /lava-2462039/1/../bin/lava-test-case <8>[ 17.297283] /lava-2462039/1/../bin/lava-test-case <8>[ 17.308614] + set +x <8>[ 17.319619] / #