Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3027 device /dev/ttyimx8mp-evk-1 [115200 N81] (Debian GNU/Linux) U-Boot SPL 2019.04-5.4.3-2.0.0+g47c1922978 (Mar 13 2020 - 23:25:39 +0000) power_pca9450b_init DDRINFO: start DRAM init DDRINFO:ddrphy calibration done DDRINFO: ddrmix config done Normal Boot Trying to boot from ROMAPI image offset 0x8000, pagesize 0x200, ivt offset 0x0 U-Boot 2019.04-5.4.3-2.0.0+g47c1922978 (Mar 13 2020 - 23:25:39 +0000) CPU: Freescale i.MX8MP rev1.0 1800 MHz (running at 1200 MHz) CPU: Commercial temperature grade (0C to 95C) at 23C Reset cause: POR Model: NXP i.MX8MPlus LPDDR4 EVK board DRAM: 6 GiB TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C2 0x50] SNK.Power3.0 on CC2 PDO 0: type 0, 5000 mV, 3000 mA [E] PDO 1: type 0, 9000 mV, 3000 mA [] PDO 2: type 0, 15000 mV, 3000 mA [] PDO 3: type 0, 20000 mV, 2250 mA [] Requesting PDO 3: 20000 mV, 2250 mA Source accept request PD source ready! tcpc_pd_receive_message: Polling ALERT register, TCPC_ALERT_RX_STATUS bit failed, ret = -62 Power supply on USB2 TCPC: Vendor ID [0x1fc9], Product ID [0x5110], Addr [I2C1 0x50] MMC: FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... Run CMD11 1.8V switch OK No panel detected: default to MIPI2HDMI adv7535_init: Can't find device id=0x3d, on bus 1 Display: MIPI2HDMI (1920x1080) Video: 1920x1080x24 In: serial Out: serial Err: serial BuildInfo: - ATF f1a195b - U-Boot 2019.04-5.4.3-2.0.0+g47c1922978 Run CMD11 1.8V switch switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Run CMD11 1.8V switch Net: eth0: ethernet@30be0000 [PRIME], eth1: ethernet@30bf0000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 2  0 u-boot=> setenv autoload no setenv autoload no u-boot=> dhcp dhcp ethernet@30be0000 Waiting for PHY auto negotiation to complete.... done BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.153 (1759 ms) u-boot=> setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 u-boot=> tftp 0x40480000 1053439/tftp-deploy-9z3rhxrv/kernel/Image tftp 0x40480000 1053439/tftp-deploy-9z3rhxrv/kernel/Image Using ethernet@30be0000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.153; sending through gateway 172.16.1.4 Filename '1053439/tftp-deploy-9z3rhxrv/kernel/Image'. Load address: 0x40480000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################## 10.5 MiB/s done Bytes transferred = 31836672 (1e5ca00 hex) u-boot=> tftp 0x44000000 1053439/tftp-deploy-9z3rhxrv/ramdisk/ramdisk.cpio.gz.uboot tftp 0x44000000 1053439/tftp-deploy-9z3rhxrv/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@30be0000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.153; sending through gateway 172.16.1.4 Filename '1053439/tftp-deploy-9z3rhxrv/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x44000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 10.5 MiB/s done Bytes transferred = 18914898 (1209e52 hex) u-boot=> setenv initrd_size ${filesize} setenv initrd_size ${filesize} u-boot=> tftp 0x43000000 1053439/tftp-deploy-9z3rhxrv/dtb/imx8mp-evk.dtb tftp 0x43000000 1053439/tftp-deploy-9z3rhxrv/dtb/imx8mp-evk.dtb Using ethernet@30be0000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.153; sending through gateway 172.16.1.4 Filename '1053439/tftp-deploy-9z3rhxrv/dtb/imx8mp-evk.dtb'. Load address: 0x43000000 Loading: *## 5.8 MiB/s done Bytes transferred = 18268 (475c hex) u-boot=> setenv bootargs 'console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' u-boot=> booti 0x40480000 0x44000000 0x43000000 booti 0x40480000 0x44000000 0x43000000 ## Loading init Ramdisk from Legacy Image at 44000000 ... Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18914834 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Using Device Tree in place at 0000000043000000, end 000000004300775b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.138-cip15 (KernelCI@build-j116758-arm64-gcc-10-defconfig-nckh2) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Tue Sep 6 00:16:51 UTC 2022 [ 0.000000] Machine model: NXP i.MX8MPlus EVK board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x0000000030890000 (options '115200n8') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x0000000030890000 (options '115200n8') [ 0.000000] ------------[ cut here ]------------ [ 0.000000] console 'ec_imx6q0' already registered [ 0.000000] WARNING: CPU: 0 PID: 0 at kernel/printk/printk.c:2770 register_console+0x58/0x2c0 [ 0.000000] Modules linked in: [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.10.138-cip15 #1 [ 0.000000] Hardware name: NXP i.MX8MPlus EVK board (DT) [ 0.000000] pstate: 60000085 (nZCv daIf -PAN -UAO -TCO BTYPE=--) [ 0.000000] pc : register_console+0x58/0x2c0 [ 0.000000] lr : register_console+0x58/0x2c0 [ 0.000000] sp : ffff800011ba3dd0 [ 0.000000] x29: ffff800011ba3dd0 x28: 0000000041bd0018 [ 0.000000] x27: 0000000000000400 x26: 0000000000000000 [ 0.000000] x25: 0000000000002f68 x24: ffff800011df3000 [ 0.000000] x23: 0000000000000000 x22: ffff80001170a5f0 [ 0.000000] x21: ffff800011e6d050 x20: ffff800011df3d50 [ 0.000000] x19: ffff800011df3d50 x18: 0000000000000005 [ 0.000000] x17: 0000000000001800 x16: 0000000000000000 [ 0.000000] x15: 0000000000000030 x14: ffffffffffffffff [ 0.000000] x13: ffff800011bc29a0 x12: 000000000000001b [ 0.000000] x11: 0000000000000009 x10: ffff800011c1a9a0 [ 0.000000] x9 : 00000000fffff000 x8 : ffff800011bc29a0 [ 0.000000] x7 : ffff800011c1a9a0 x6 : 0000000000000000 [ 0.000000] x5 : 0000000000000000 x4 : 0000000000000000 [ 0.000000] x3 : 00000000ffffffff x2 : 0000000000000000 [ 0.000000] x1 : 0000000000000000 x0 : ffff800011bb3400 [ 0.000000] Call trace: [ 0.000000] register_console+0x58/0x2c0 [ 0.000000] of_setup_earlycon+0x248/0x26c [ 0.000000] early_init_dt_scan_chosen_stdout+0x160/0x1a4 [ 0.000000] acpi_boot_table_init+0x158/0x198 [ 0.000000] setup_arch+0x284/0x600 [ 0.000000] start_kernel+0x74/0x4c8 [ 0.000000] ---[ end trace 9b12576c32ad7751 ]--- [ 0.000000] NUMA: No NUMA c# onfiguration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x00000001bfffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x1bf3f4b00-0x1bf3f6fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000001bfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000055ffffff] [ 0.000000] node 0: [mem 0x0000000058000000-0x00000001bfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000001bfffffff] [ 0.000000] cma: Reserved 32 MiB at 0x00000000fe000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 23 pages/cpu s56600 r8192 d29416 u94208 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1540096 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] software IO TLB: mapped [mem 0x00000000fa000000-0x00000000fe000000] (64MB) <6>[ 0.000000] Memory: 5986524K/6258688K available (14592K kernel code, 2802K rwdata, 7600K rodata, 5952K init, 512K bss, 239396K reserved, 32768K cma-reserved) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. <6>[ 0.000000] Trampoline variant of Tasks RCU enabled. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 <6>[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode <6>[ 0.000000] GICv3: 160 SPIs implemented <6>[ 0.000000] GICv3: 0 Extended SPIs implemented <6>[ 0.000000] GICv3: Distributor has no Range Selector support <6>[ 0.000000] GICv3: 16 PPIs implemented <6>[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000038880000 <4>[ 0.000000] ITS: No ITS available, not enabling LPIs <6>[ 0.000000] arch_timer: cp15 timer(s) running at 8.00MHz (phys). <6>[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 440795202120 ns <6>[ 0.000003] sched_clock: 56 bits at 8MHz, resolution 125ns, wraps every 2199023255500ns <6>[ 0.008840] Console: colour dummy device 80x25 <6>[ 0.013107] Calibrating delay loop (skipped), value calculated using timer frequency.. 16.00 BogoMIPS (lpj=32000) <6>[ 0.023631] pid_max: default: 32768 minimum: 301 <6>[ 0.028590] LSM: Security Framework initializing <6>[ 0.033486] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.041325] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 0.050843] rcu: Hierarchical SRCU implementation. <6>[ 0.055860] EFI services will not be available. <6>[ 0.059716] smp: Bringing up secondary CPUs ... <6>[ 0.064712] Detected VIPT I-cache on CPU1 <6>[ 0.064738] GICv3: CPU1: found redistributor 1 region 0:0x00000000388a0000 <6>[ 0.064768] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] <6>[ 0.065208] Detected VIPT I-cache on CPU2 <6>[ 0.065226] GICv3: CPU2: found redistributor 2 region 0:0x00000000388c0000 <6>[ 0.065244] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] <6>[ 0.065656] Detected VIPT I-cache on CPU3 <6>[ 0.065672] GICv3: CPU3: found redistributor 3 region 0:0x00000000388e0000 <6>[ 0.065691] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] <6>[ 0.065747] smp: Brought up 1 node, 4 CPUs <6>[ 0.123563] SMP: Total of 4 processors activated. <6>[ 0.128543] CPU features: detected: 32-bit EL0 Support <6>[ 0.133985] CPU features: detected: CRC32 instructions <6>[ 0.139396] CPU features: detected: 32-bit EL1 Support <6>[ 0.151330] CPU: All CPU(s) started at EL2 <6>[ 0.152876] alternatives: patching kernel code <6>[ 0.159103] devtmpfs: initialized <4>[ 0.163914] KASLR disabled due to lack of seed <6>[ 0.166019] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns <6>[ 0.175951] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.184083] pinctrl core: initialized pinctrl subsystem <6>[ 0.189602] DMI not present or invalid. <6>[ 0.193370] NET: Registered protocol family 16 <6>[ 0.198592] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.205121] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.213432] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.221386] audit: initializing netlink subsys (disabled) <5>[ 0.227163] audit: type=2000 audit(0.152:1): state=initialized audit_enabled=0 res=1 <6>[ 0.227962] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.235097] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.241760] cpuidle: using governor menu <6>[ 0.252589] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. <6>[ 0.259563] ASID allocator initialised with 65536 entries <6>[ 0.266472] Serial: AMBA PL011 UART driver <6>[ 0.283374] imx8mp-pinctrl 30330000.pinctrl: initialized IMX pinctrl driver <6>[ 0.298777] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.302926] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages <6>[ 0.309921] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.316918] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages <6>[ 0.324866] cryptd: max_cpu_qlen set to 1000 <6>[ 0.330748] ACPI: Interpreter disabled. <6>[ 0.333920] iommu: Default domain type: Translated <6>[ 0.337915] vgaarb: loaded <5>[ 0.340954] SCSI subsystem initialized <6>[ 0.345040] usbcore: registered new interface driver usbfs <6>[ 0.350556] usbcore: registered new interface driver hub <6>[ 0.356139] usbcore: registered new device driver usb <6>[ 0.362114] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.366707] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.376162] PTP clock support registered <6>[ 0.380447] EDAC MC: Ver: 3.0.0 <6>[ 0.384787] FPGA manager framework <6>[ 0.387513] Advanced Linux Sound Architecture Driver Initialized. <6>[ 0.394501] clocksource: Switched to clocksource arch_sys_counter <5>[ 0.400370] VFS: Disk quotas dquot_6.6.0 <6>[ 0.404462] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 0.411747] pnp: PnP ACPI: disabled <6>[ 0.420760] NET: Registered protocol family 2 <6>[ 0.422770] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) <6>[ 0.433113] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear) <6>[ 0.439340] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.447883] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) <6>[ 0.456065] TCP: Hash tables configured (established 65536 bind 65536) <6>[ 0.462150] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear) <6>[ 0.469239] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear) <6>[ 0.476866] NET: Registered protocol family 1 <6>[ 0.481613] RPC: Registered named UNIX socket transport module. <6>[ 0.487465] RPC: Registered udp transport module. <6>[ 0.492450] RPC: Registered tcp transport module. <6>[ 0.497436] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 0.504178] PCI: CLS 0 bytes, default 64 <6>[ 0.508503] Unpacking initramfs... <6>[ 1.402666] Freeing initrd memory: 18464K <6>[ 1.404643] kvm [1]: IPA Size Limit: 40 bits <6>[ 1.410267] kvm [1]: GICv3: no GICV resource entry <6>[ 1.413723] kvm [1]: disabling GICv2 emulation <6>[ 1.418460] kvm [1]: GIC system register CPU interface enabled <6>[ 1.424646] kvm [1]: vgic interrupt IRQ9 <6>[ 1.428875] kvm [1]: Hyp mode initialized successfully <5>[ 1.437267] Initialise system trusted keyrings <6>[ 1.439266] workingset: timestamp_bits=42 max_order=21 bucket_order=0 <6>[ 1.451924] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 1.455764] NFS: Registering the id_resolver key type <5>[ 1.460559] Key type id_resolver registered <5>[ 1.464989] Key type id_legacy registered <6>[ 1.469350] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 1.476281] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 1.484105] 9p: Installing v9fs 9p2000 file system support <5>[ 1.525317] Key type asymmetric registered <5>[ 1.526831] Asymmetric key parser 'x509' registered <6>[ 1.532017] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) <6>[ 1.539692] io scheduler mq-deadline registered <6>[ 1.544502] io scheduler kyber registered <4>[ 1.556562] EINJ: ACPI disabled. <3>[ 1.561879] clk: failed to reparent gic to sys_pll2_500m: -16 <6>[ 1.570367] SoC: i.MX8MP revision 1.0 <6>[ 1.577561] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled <6>[ 1.583205] SuperH (H)SCI(F) driver initialized <6>[ 1.586525] 30890000.serial: ttymxc1 at MMIO 0x30890000 (irq = 30, base_baud = 1500000) is a IMX <6>[ 1.595220] printk: console [ttymxc1] enabled <6>[ 1.595220] printk: console [ttymxc1] enabled <6>[ 1.604394] printk: bootconsole [ec_imx6q0] disabled <6>[ 1.604394] printk: bootconsole [ec_imx6q0] disabled <6>[ 1.615478] msm_serial: driver initialized <6>[ 1.628845] loop: module loaded <6>[ 1.632964] megasas: 07.714.04.00-rc1 <6>[ 1.641505] tun: Universal TUN/TAP device driver, 1.6 <6>[ 1.647435] thunder_xcv, ver 1.0 <6>[ 1.650965] thunder_bgx, ver 1.0 <6>[ 1.654481] nicpf, ver 1.0 <6>[ 1.658256] pps pps0: new PPS source ptp0 <6>[ 1.678885] hclge is initializing <6>[ 1.682482] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version <6>[ 1.689981] hns3: Copyright (c) 2017 Huawei Corporation. <6>[ 1.695597] e1000: Intel(R) PRO/1000 Network Driver <6>[ 1.700759] e1000: Copyright (c) 1999-2006 Intel Corporation. <6>[ 1.706817] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 1.712051] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 1.718275] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 1.723940] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 1.729804] igbvf: Intel(R) Gigabit Virtual Function Network Driver <6>[ 1.736337] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. <6>[ 1.742785] sky2: driver version 1.30 <6>[ 1.747574] VFIO - User Level meta-driver version: 0.3 <6>[ 1.754395] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 1.761205] ehci-pci: EHCI PCI platform driver <6>[ 1.765945] ehci-platform: EHCI generic platform driver <6>[ 1.771538] ehci-orion: EHCI orion driver <6>[ 1.775890] ehci-exynos: EHCI Exynos driver <6>[ 1.780405] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 1.786867] ohci-pci: OHCI PCI platform driver <6>[ 1.791607] ohci-platform: OHCI generic platform driver <6>[ 1.797180] ohci-exynos: OHCI Exynos driver <6>[ 1.802016] usbcore: registered new interface driver usb-storage <6>[ 1.810357] i2c /dev entries driver <6>[ 1.819503] sdhci: Secure Digital Host Controller Interface driver <6>[ 1.825964] sdhci: Copyright(c) Pierre Ossman <6>[ 1.830988] Synopsys Designware Multimedia Card Interface Driver <6>[ 1.838029] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 1.845500] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 1.853014] usbcore: registered new interface driver usbhid <6>[ 1.858862] usbhid: USB HID core driver <6>[ 1.865999] optee: probing for conduit method. <6>[ 1.870737] optee: revision 3.7 (b32a9b6b) <6>[ 1.871064] optee: initialized driver <6>[ 1.876030] mmc2: SDHCI controller on 30b60000.mmc [30b60000.mmc] using ADMA <6>[ 1.880558] NET: Registered protocol family 17 <6>[ 1.891544] 9pnet: Installing 9P2000 support <5>[ 1.896127] Key type dns_resolver registered <6>[ 1.900894] registered taskstats version 1 <5>[ 1.905291] Loading compiled-in X.509 certificates <4>[ 1.929813] pca953x 2-0020: supply vcc not found, using dummy regulator <6>[ 1.936818] pca953x 2-0020: using no AI <6>[ 1.942296] i2c i2c-2: IMX I2C adapter registered <6>[ 1.949060] pps pps0: new PPS source ptp0 <6>[ 1.970313] mmc2: new HS400 MMC card at address 0001 <6>[ 1.976014] mmcblk2: mmc2:0001 IB2932 29.2 GiB <6>[ 1.980972] mmcblk2boot0: mmc2:0001 IB2932 partition 1 4.00 MiB <6>[ 1.987315] mmcblk2boot1: mmc2:0001 IB2932 partition 2 4.00 MiB <6>[ 1.993615] mmcblk2rpmb: mmc2:0001 IB2932 partition 3 4.00 MiB, chardev (234:0) <6>[ 2.163143] fec 30be0000.ethernet eth0: registered PHC device 0 <6>[ 2.172581] sdhci-esdhc-imx 30b50000.mmc: Got CD GPIO <6>[ 2.209137] mmc1: SDHCI controller on 30b50000.mmc [30b50000.mmc] using ADMA <6>[ 2.334530] RTL8211F Gigabit Ethernet 30be0000.ethernet-1:01: attached PHY driver [RTL8211F Gigabit Ethernet] (mii_bus:phy_addr=30be0000.ethernet-1:01, irq=POLL) <4>[ 2.344499] mmc1: host does not support reading read-only switch, assuming write-enable <6>[ 2.361341] mmc1: new ultra high speed DDR50 SDHC card at address aaaa <6>[ 2.368604] mmcblk1: mmc1:aaaa SL16G 14.8 GiB <6>[ 2.380654] mmcblk1: p1 p2 <6>[ 6.479328] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <5>[ 6.510509] Sending DHCP requests .., OK <6>[ 8.786726] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.153 <6>[ 8.794570] IP-Config: Complete: <6>[ 8.798064] device=eth0, hwaddr=00:04:9f:06:96:3c, ipaddr=172.16.1.153, mask=255.255.255.0, gw=172.16.1.4 <6>[ 8.808332] host=172.16.1.153, domain=example.org, nis-domain=(none) <6>[ 8.815389] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 8.815392] nameserver0=172.16.1.4 <6>[ 8.827723] ALSA device list: <6>[ 8.830964] No soundcards found. <6>[ 8.836558] Freeing unused kernel memory: 5952K <6>[ 8.846603] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 8.901203] udevd[160]: starting version 3.2.9 <5>[ 8.906624] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.913514] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 8.920273] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 8.931461] udevd[160]: specified user 'tss' unknown <27>[ 8.936866] udevd[160]: specified group 'tss' unknown <30>[ 8.943411] udevd[161]: starting eudev-3.2.9 <6>[ 9.173740] caam 30900000.crypto: RNG4 SH0 was previously instantiated without prediction resistance. Tearing it down <4>[ 9.204921] imx-sdma 30bd0000.dma-controller: Direct firmware load for imx/sdma/sdma-imx7d.bin failed with error -2 <4>[ 9.216427] imx-sdma 30bd0000.dma-controller: Falling back to sysfs fallback for: imx/sdma/sdma-imx7d.bin <3>[ 9.273468] caam 30900000.crypto: failed to acquire DECO 0 <3>[ 9.279263] caam 30900000.crypto: Failed to deinstantiate RNG4 SH0 <3>[ 9.291317] caam 30900000.crypto: failed to instantiate RNG <6>[ 9.298809] input: 30370000.snvs:snvs-powerkey as /devices/platform/soc@0/30000000.bus/30370000.snvs/30370000.snvs:snvs-powerkey/input/input0 <6>[ 9.313740] snvs_rtc 30370000.snvs:snvs-rtc-lp: registered as rtc0 <6>[ 9.320308] snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01T00:00:00 UTC (0) done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <6>[ 9.460181] NET: Registered protocol family 10 <6>[ 9.465768] Segment Routing with IPv6 OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1053439/environment . /lava-1053439/environment / # /lava-1053439/bin/lava-test-runner /lava-1053439/0 /lava-1053439/bin/lava-test-runner /lava-1053439/0 + export 'TESTRUN_ID=0_dmesg' + cd /la<8>[ 15.237887] va-1053439/0/tests/0_dmesg + cat uuid + UUID=1053439_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 15.261240] <8>[ 15.284535] <8>[ 15.307960] + set<8>[ 15.317451] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-1053439/environment / # . /lava-1053439/environment/lava-1053439/bin/lava-test-runner /lava-1053439/1 / # /lava-1053439/bin/lava-test-runner /lava-1053439/1 + export 'TESTRUN_ID=1_bootrr' + cd /l<8>[ 21.007809] ava-1053439/1/tests/1_bootrr + cat uuid + UUID=1053439_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-1053439/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-1053439/1/../bin/lava-test-case <8>[ 22.030343] /lava-1053439/1/../bin/lava-test-case <8>[ 22.052035] /lava-1053439/1/../bin/lava-test-case <8>[ 22.067166] + set<8>[ 22.079916] +x / #