[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.37 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7902646/tftp-deploy-87uldst0/kernel/zImage tftp 0x10000000 7902646/tftp-deploy-87uldst0/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '7902646/tftp-deploy-87uldst0/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 5.3 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x14000000 7902646/tftp-deploy-87uldst0/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7902646/tftp-deploy-87uldst0/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '7902646/tftp-deploy-87uldst0/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ####################################################### 5.6 MiB/s done Bytes transferred = 16064560 (f52030 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7902646/tftp-deploy-87uldst0/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7902646/tftp-deploy-87uldst0/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.37 Filename '7902646/tftp-deploy-87uldst0/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 3.4 MiB/s done Bytes transferred = 42393 (a599 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16064496 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d598 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.147-cip18 (KernelCI@build-j473716-arm-gcc-10-multi-v7-defconfig-mqg2x) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Nov 8 19:33:57 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 933700K/1048576K available (13312K kernel code, 2230K rwdata, 5344K rodata, 2048K init, 424K bss, 49340K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022277] Console: colour dummy device 80x30 <6>[ 0.024165] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034579] pid_max: default: 32768 minimum: 301 <6>[ 0.039615] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.047032] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055661] CPU: Testing write buffer coherency: ok <6>[ 0.060146] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065706] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.072049] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079748] rcu: Hierarchical SRCU implementation. <6>[ 0.086735] EFI services will not be available. <6>[ 0.088968] smp: Bringing up secondary CPUs ... <6>[ 0.094241] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094249] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105593] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105602] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116793] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116801] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127251] smp: Brought up 1 node, 4 CPUs <6>[ 0.131479] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137937] CPU: All CPU(s) started in SVC mode. <6>[ 0.143352] devtmpfs: initialized <6>[ 0.153652] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158989] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168865] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179061] pinctrl core: initialized pinctrl subsystem <6>[ 0.183460] DMI not present or invalid. <6>[ 0.186665] NET: Registered protocol family 16 <6>[ 0.193906] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200468] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200653] cpuidle: using governor menu <6>[ 0.208815] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.382453] vdd1p1: supplied by regulator-dummy <6>[ 0.391360] vdd3p0: supplied by regulator-dummy <6>[ 0.400189] vdd2p5: supplied by regulator-dummy <6>[ 0.409035] vddarm: supplied by regulator-dummy <6>[ 0.418075] vddpu: supplied by regulator-dummy <6>[ 0.426684] vddsoc: supplied by regulator-dummy <6>[ 0.745937] No ATAGs? <6>[ 0.746115] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.753879] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.764006] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.774147] Serial: AMBA PL011 UART driver <6>[ 0.778306] printk: console [ramoops-1] enabled <6>[ 0.780649] pstore: Registered ramoops as persistent store backend <6>[ 0.786904] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.818285] mxs-dma 110000.dma-apbh: initialized <6>[ 0.827839] iommu: Default domain type: Translated <6>[ 0.830578] vgaarb: loaded <5>[ 0.833949] SCSI subsystem initialized <6>[ 0.837706] usbcore: registered new interface driver usbfs <6>[ 0.842876] usbcore: registered new interface driver hub <6>[ 0.848456] usbcore: registered new device driver usb <6>[ 0.855241] i2c i2c-0: IMX I2C adapter registered <6>[ 0.860026] i2c i2c-1: IMX I2C adapter registered <6>[ 0.864431] i2c i2c-2: IMX I2C adapter registered <6>[ 0.869933] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.873802] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.883234] PTP clock support registered <6>[ 0.890908] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.944703] NET: Registered protocol family 2 <6>[ 1.946906] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.955316] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.962799] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.970825] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.978305] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.984997] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.991700] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.999104] NET: Registered protocol family 1 <6>[ 2.004169] RPC: Registered named UNIX socket transport module. <6>[ 2.009723] RPC: Registered udp transport module. <6>[ 2.014715] RPC: Registered tcp transport module. <6>[ 2.019640] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.026368] PCI: CLS 0 bytes, default 64 <6>[ 2.031054] Trying to unpack rootfs image as initramfs... <6>[ 3.373766] Freeing initrd memory: 15692K <4>[ 3.375656] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 3.383018] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.392776] Initialise system trusted keyrings <6>[ 3.395975] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.408175] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.412160] NFS: Registering the id_resolver key type <5>[ 3.416757] Key type id_resolver registered <5>[ 3.421192] Key type id_legacy registered <6>[ 3.425522] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.432405] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.440069] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.445157] Key type asymmetric registered <5>[ 3.449006] Asymmetric key parser 'x509' registered <6>[ 3.454205] bounce: pool size: 64 pages <6>[ 3.458259] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.465906] io scheduler mq-deadline registered <6>[ 3.470667] io scheduler kyber registered <4>[ 3.517208] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.524156] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.586917] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.595114] SuperH (H)SCI(F) driver initialized <6>[ 3.598068] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.606965] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.614868] printk: console [ttymxc1] enabled <6>[ 3.614868] printk: console [ttymxc1] enabled <6>[ 3.624035] printk: bootconsole [ec_imx21] disabled <6>[ 3.624035] printk: bootconsole [ec_imx21] disabled <6>[ 3.635739] msm_serial: driver initialized <6>[ 3.641777] STMicroelectronics ASC driver initialized <6>[ 3.649027] STM32 USART driver initialized <4>[ 3.664420] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.672348] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.679152] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.695796] brd: module loaded <6>[ 3.709107] loop: module loaded <6>[ 3.716400] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.724632] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.732936] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.741397] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.749397] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.757136] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.764706] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.775317] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.782603] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.791685] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.802475] scsi host0: ahci-imx <6>[ 3.806343] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.826834] CAN device driver interface <6>[ 3.832301] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.841795] pps pps0: new PPS source ptp0 <6>[ 3.878575] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.886172] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.891430] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.897678] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.903362] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.915281] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.923017] usbcore: registered new interface driver pegasus <6>[ 3.928983] usbcore: registered new interface driver asix <6>[ 3.934699] usbcore: registered new interface driver ax88179_178a <6>[ 3.941106] usbcore: registered new interface driver cdc_ether <6>[ 3.947244] usbcore: registered new interface driver smsc75xx <6>[ 3.953316] usbcore: registered new interface driver smsc95xx <6>[ 3.959367] usbcore: registered new interface driver net1080 <6>[ 3.965344] usbcore: registered new interface driver cdc_subset <6>[ 3.971579] usbcore: registered new interface driver zaurus <6>[ 3.977484] usbcore: registered new interface driver cdc_ncm <6>[ 3.986927] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.993745] ehci-pci: EHCI PCI platform driver <6>[ 3.998495] ehci-platform: EHCI generic platform driver <6>[ 4.004308] ehci-orion: EHCI orion driver <6>[ 4.008805] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.013296] ehci-st: EHCI STMicroelectronics driver <6>[ 4.018625] ehci-exynos: EHCI Exynos driver <6>[ 4.023276] ehci-atmel: EHCI Atmel driver <6>[ 4.027730] tegra-ehci: Tegra EHCI driver <6>[ 4.032236] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.038701] ohci-pci: OHCI PCI platform driver <6>[ 4.043470] ohci-platform: OHCI generic platform driver <6>[ 4.049235] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.053726] ohci-st: OHCI STMicroelectronics driver <6>[ 4.059057] ohci-atmel: OHCI Atmel driver <6>[ 4.064404] usbcore: registered new interface driver usb-storage <6>[ 4.078718] i2c /dev entries driver <6>[ 4.101727] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.108178] sdhci: Copyright(c) Pierre Ossman <6>[ 4.115497] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.123708] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 4.131664] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 4.131818] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 4.136929] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 4.147696] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.155016] usbcore: registered new interface driver usbhid <6>[ 4.160885] usbhid: USB HID core driver <6>[ 4.160933] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 4.170725] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 4.171459] NET: Registered protocol family 10 <6>[ 4.173743] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 4.177288] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 4.183051] Segment Routing with IPv6 <6>[ 4.200554] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.206986] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 4.207380] NET: Registered protocol family 17 <6>[ 4.218883] can: controller area network core <6>[ 4.223613] NET: Registered protocol family 29 <6>[ 4.228326] can: raw protocol <6>[ 4.231586] can: broadcast manager protocol <6>[ 4.236045] can: netlink gateway - max_hops=1 <5>[ 4.241152] Key type dns_resolver registered <6>[ 4.247749] ThumbEE CPU extension supported. <5>[ 4.252330] Registering SWP/SWPB emulation handler <6>[ 4.252754] mmc2: new high speed SDHC card at address e624 <5>[ 4.257650] Loading compiled-in X.509 certificates <6>[ 4.264003] mmcblk2: mmc2:e624 SL16G 14.8 GiB <6>[ 4.273680] pstore: Using crash dump compression: deflate <4>[ 4.281567] GPT:Primary header thinks Alt. header is not at the end of the disk. <4>[ 4.289255] GPT:29296874 != 31116287 <4>[ 4.293141] GPT:Alternate GPT header not at the end of the disk. <4>[ 4.299423] GPT:29296874 != 31116287 <4>[ 4.300726] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.303282] GPT: Use GNU Parted to correct GPT errors. <6>[ 4.303341] mmcblk2: p1 p2 p3 <4>[ 4.311221] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.327883] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.343946] imx_usb 2184200.usb: No over current polarity defined <6>[ 4.353809] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 4.358976] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 4.390946] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 4.397973] hub 1-0:1.0: USB hub found <6>[ 4.402130] hub 1-0:1.0: 1 port detected <6>[ 4.410698] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.425927] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.433854] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.441797] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.453966] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.461876] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.469693] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.479808] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.492029] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.499914] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.507844] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.522156] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.730946] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.932576] hub 1-1:1.0: USB hub found <6>[ 4.936809] hub 1-1:1.0: 3 ports detected <4>[ 4.947383] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.955356] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.963629] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.681394] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.690985] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.720889] Sending DHCP requests ., OK <6>[ 7.765148] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.37 <6>[ 7.773481] IP-Config: Complete: <6>[ 7.777002] device=eth0, hwaddr=00:19:b8:08:f0:fd, ipaddr=192.168.201.37, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.787763] host=imx6q-sabrelite-lava-cbg-7, domain=lava-rack, nis-domain=(none) <6>[ 7.795915] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.795927] nameserver0=192.168.201.1 <6>[ 7.815244] Freeing unused kernel memory: 2048K <6>[ 7.841408] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 7.963878] udevd[137]: starting version 3.2.9 <5>[ 7.969643] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.977276] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 7.984103] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 7.997825] udevd[137]: specified user 'tss' unknown <27>[ 8.003433] udevd[137]: specified group 'tss' unknown <30>[ 8.010968] udevd[138]: starting eudev-3.2.9 <6>[ 8.406376] imx-ipuv3 2400000.ipu: IPUv3H probed <6>[ 8.413304] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.423869] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.431954] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.445962] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.460955] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.468892] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.502242] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.515762] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.523836] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.621169] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.655317] panel-simple panel-lcd: supply power not found, using dummy regulator <6>[ 8.661403] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <4>[ 8.663277] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.674073] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.683896] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.690708] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.706287] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.740586] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.747006] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.790981] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <4>[ 8.799660] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.820134] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.828127] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.839312] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.851741] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.860303] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.868902] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.877507] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 8.905496] caam 2100000.crypto: Instantiated RNG4 SH0 <4>[ 8.934347] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.952911] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.960831] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.966255] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.972729] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.979615] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 9.000180] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.008784] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.017389] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.025928] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.065977] sgtl5000 0-000a: sgtl5000 revision 0x11 <4>[ 9.068180] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <6>[ 9.075558] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 9.079336] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 9.095729] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 9.103924] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <4>[ 9.143426] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.157260] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.165335] panel-simple panel-lcd: Specify missing connector_type <6>[ 9.179494] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 9.188064] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 9.196624] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 9.205151] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.436064] caam algorithms registered in /proc/crypto <6>[ 9.443013] caam 2100000.crypto: registering rng-caam <4>[ 9.449974] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 9.466134] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.474110] panel-simple panel-lcd: Specify missing connector_type done <6>[ 9.486348] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) Saving random seed: <6>[ 9.494976] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <5>[ 9.504339] random: dd: uninitialized urandom read (32 bytes read) <6>[ 9.505132] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) OK <6>[ 9.519965] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) Starting network: <4>[ 9.530829] panel-simple panel-lvds0: supply power not found, using dummy regulator ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: <5>[ 9.597682] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # <5>[ 9.630743] random: crng init done <5>[ 9.634989] random: 1 urandom warning(s) missed due to ratelimiting / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-7902646/environment . /lava-7902646/environment / # /lava-7902646/bin/lava-test-runner /lava-7902646/0 /lava-7902646/bin/lava-test-runner /lava-7902646/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-7902646/0/tests/0_dmesg + c<8>[ 10.220131] at uuid + UUID=7902646_1.5.2.4.1 + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 10.263886] <8>[ 10.304747] <8>[ 10.345757] + set<8>[ 10.355713] +x / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-7902646/environment / # . /lava-7902646/environment/lava-7902646/bin/lava-test-runner /lava-7902646/1 / # /lava-7902646/bin/lava-test-runner /lava-7902646/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-7902646/1/tests/1_bootrr +<8>[ 10.864933] cat uuid + UUID=7902646_1.5.2.4.5 + set +x + export 'PATH=/opt/bootrr/helpers:/lava-7902646/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr + sh helpers/bootrr-auto /lava-7902646/1/../bin/lava-test-case <8>[ 11.918705] /lava-7902646/1/../bin/lava-test-case <8>[ 11.958136] /lava-7902646/1/../bin/lava-test-case <8>[ 11.983169] + set<8>[ 12.002114] +x / #