[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.33 (3 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 7902672/tftp-deploy-kw09wyv8/kernel/zImage tftp 0x10000000 7902672/tftp-deploy-kw09wyv8/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '7902672/tftp-deploy-kw09wyv8/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######### 11 MiB/s done Bytes transferred = 9667072 (938200 hex) => tftp 0x14000000 7902672/tftp-deploy-kw09wyv8/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 7902672/tftp-deploy-kw09wyv8/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '7902672/tftp-deploy-kw09wyv8/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################### 11.5 MiB/s done Bytes transferred = 12135574 (b92c96 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 7902672/tftp-deploy-kw09wyv8/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 7902672/tftp-deploy-kw09wyv8/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.33 Filename '7902672/tftp-deploy-kw09wyv8/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 5.8 MiB/s done Bytes transferred = 42393 (a599 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7902672/extract-nfsrootfs-r0qgd4lu,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7902672/extract-nfsrootfs-r0qgd4lu,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x938200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12135510 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d598 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.147-cip18 (KernelCI@build-j473716-arm-gcc-10-multi-v7-defconfig-mqg2x) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Nov 8 19:33:57 UTC 2022 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] earlycon: ec_imx21 at MMIO 0x021e8000 (options '') [ 0.000000] printk: bootconsole [ec_imx21] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/7902672/extract-nfsrootfs-r0qgd4lu,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 937540K/1048576K available (13312K kernel code, 2230K rwdata, 5344K rodata, 2048K init, 424K bss, 45500K reserved, 65536K cma-reserved, 196608K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] L2C-310 errata 752271 769419 enabled <6>[ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 <6>[ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 <6>[ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines <6>[ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled <6>[ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB <6>[ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 <6>[ 0.000000] Switching to timer-based delay loop, resolution 333ns <6>[ 0.000007] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns <6>[ 0.008444] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns <6>[ 0.022231] Console: colour dummy device 80x30 <6>[ 0.024123] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) <6>[ 0.034534] pid_max: default: 32768 minimum: 301 <6>[ 0.039571] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.046988] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) <6>[ 0.055603] CPU: Testing write buffer coherency: ok <6>[ 0.060102] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.065661] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.071999] Setting up static identity map for 0x10300000 - 0x103000ac <6>[ 0.079707] rcu: Hierarchical SRCU implementation. <6>[ 0.086696] EFI services will not be available. <6>[ 0.088925] smp: Bringing up secondary CPUs ... <6>[ 0.094206] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>[ 0.094215] CPU1: Spectre v2: using BPIALL workaround <6>[ 0.105548] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 <6>[ 0.105557] CPU2: Spectre v2: using BPIALL workaround <6>[ 0.116751] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 <6>[ 0.116758] CPU3: Spectre v2: using BPIALL workaround <6>[ 0.127210] smp: Brought up 1 node, 4 CPUs <6>[ 0.131438] SMP: Total of 4 processors activated (24.00 BogoMIPS). <6>[ 0.137897] CPU: All CPU(s) started in SVC mode. <6>[ 0.143322] devtmpfs: initialized <6>[ 0.153657] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 <6>[ 0.158996] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.168869] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) <6>[ 0.179068] pinctrl core: initialized pinctrl subsystem <6>[ 0.183478] DMI not present or invalid. <6>[ 0.186672] NET: Registered protocol family 16 <6>[ 0.193939] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.200509] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.200694] cpuidle: using governor menu <6>[ 0.208862] CPU identified as i.MX6Q, silicon rev 1.2 <6>[ 0.382423] vdd1p1: supplied by regulator-dummy <6>[ 0.391331] vdd3p0: supplied by regulator-dummy <6>[ 0.400149] vdd2p5: supplied by regulator-dummy <6>[ 0.408988] vddarm: supplied by regulator-dummy <6>[ 0.417987] vddpu: supplied by regulator-dummy <6>[ 0.426587] vddsoc: supplied by regulator-dummy <6>[ 0.745977] No ATAGs? <6>[ 0.746162] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. <6>[ 0.753921] hw-breakpoint: maximum watchpoint size is 4 bytes. <6>[ 0.764063] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.774185] Serial: AMBA PL011 UART driver <6>[ 0.778336] printk: console [ramoops-1] enabled <6>[ 0.780692] pstore: Registered ramoops as persistent store backend <6>[ 0.786941] ramoops: using 0x10000@0x30000000, ecc: 0 <6>[ 0.818337] mxs-dma 110000.dma-apbh: initialized <6>[ 0.827853] iommu: Default domain type: Translated <6>[ 0.830585] vgaarb: loaded <5>[ 0.833970] SCSI subsystem initialized <6>[ 0.837713] usbcore: registered new interface driver usbfs <6>[ 0.842890] usbcore: registered new interface driver hub <6>[ 0.848472] usbcore: registered new device driver usb <6>[ 0.855258] i2c i2c-0: IMX I2C adapter registered <6>[ 0.860052] i2c i2c-1: IMX I2C adapter registered <6>[ 0.864448] i2c i2c-2: IMX I2C adapter registered <6>[ 0.869937] pps_core: LinuxPPS API ver. 1 registered <6>[ 0.873816] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 0.883248] PTP clock support registered <6>[ 0.890915] clocksource: Switched to clocksource mxc_timer1 <6>[ 1.944942] NET: Registered protocol family 2 <6>[ 1.947135] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) <6>[ 1.955544] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 1.963036] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) <6>[ 1.971082] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 1.978524] TCP: Hash tables configured (established 8192 bind 8192) <6>[ 1.985234] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.991945] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) <6>[ 1.999346] NET: Registered protocol family 1 <6>[ 2.004415] RPC: Registered named UNIX socket transport module. <6>[ 2.009963] RPC: Registered udp transport module. <6>[ 2.014954] RPC: Registered tcp transport module. <6>[ 2.019879] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.026607] PCI: CLS 0 bytes, default 64 <6>[ 2.031293] Trying to unpack rootfs image as initramfs... <6>[ 2.987657] Freeing initrd memory: 11852K <4>[ 2.989684] hw perfevents: no interrupt-affinity property for /pmu, guessing. <6>[ 2.996924] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available <5>[ 3.006662] Initialise system trusted keyrings <6>[ 3.009917] workingset: timestamp_bits=30 max_order=18 bucket_order=0 <6>[ 3.022078] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.026039] NFS: Registering the id_resolver key type <5>[ 3.030676] Key type id_resolver registered <5>[ 3.035097] Key type id_legacy registered <6>[ 3.039428] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.046309] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.053998] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.059039] Key type asymmetric registered <5>[ 3.062936] Asymmetric key parser 'x509' registered <6>[ 3.068089] bounce: pool size: 64 pages <6>[ 3.072179] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) <6>[ 3.079787] io scheduler mq-deadline registered <6>[ 3.084587] io scheduler kyber registered <4>[ 3.131096] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 3.138008] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 3.193991] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 3.202168] SuperH (H)SCI(F) driver initialized <6>[ 3.205095] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX <6>[ 3.214013] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX <6>[ 3.221923] printk: console [ttymxc1] enabled <6>[ 3.221923] printk: console [ttymxc1] enabled <6>[ 3.231087] printk: bootconsole [ec_imx21] disabled <6>[ 3.231087] printk: bootconsole [ec_imx21] disabled <6>[ 3.242770] msm_serial: driver initialized <6>[ 3.248777] STMicroelectronics ASC driver initialized <6>[ 3.256082] STM32 USART driver initialized <4>[ 3.271388] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.279289] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.286131] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 3.302863] brd: module loaded <6>[ 3.316157] loop: module loaded <6>[ 3.323497] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 <6>[ 3.331710] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 <6>[ 3.339986] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 <6>[ 3.348448] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 <4>[ 3.356464] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator <4>[ 3.364236] ahci-imx 2200000.sata: supply phy not found, using dummy regulator <4>[ 3.371805] ahci-imx 2200000.sata: supply target not found, using dummy regulator <6>[ 3.382385] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled <6>[ 3.389641] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>[ 3.398739] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst <6>[ 3.409548] scsi host0: ahci-imx <6>[ 3.413434] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 <6>[ 3.433792] CAN device driver interface <6>[ 3.439207] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 3.448733] pps pps0: new PPS source ptp0 <6>[ 3.471141] fec 2188000.ethernet eth0: registered PHC device 0 <6>[ 3.478725] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 3.483984] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 3.490230] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 3.495913] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 3.507759] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 3.515490] usbcore: registered new interface driver pegasus <6>[ 3.521473] usbcore: registered new interface driver asix <6>[ 3.527172] usbcore: registered new interface driver ax88179_178a <6>[ 3.533582] usbcore: registered new interface driver cdc_ether <6>[ 3.539738] usbcore: registered new interface driver smsc75xx <6>[ 3.545818] usbcore: registered new interface driver smsc95xx <6>[ 3.551879] usbcore: registered new interface driver net1080 <6>[ 3.557834] usbcore: registered new interface driver cdc_subset <6>[ 3.564068] usbcore: registered new interface driver zaurus <6>[ 3.569974] usbcore: registered new interface driver cdc_ncm <6>[ 3.579411] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 3.586230] ehci-pci: EHCI PCI platform driver <6>[ 3.590993] ehci-platform: EHCI generic platform driver <6>[ 3.596772] ehci-orion: EHCI orion driver <6>[ 3.601288] SPEAr-ehci: EHCI SPEAr driver <6>[ 3.605748] ehci-st: EHCI STMicroelectronics driver <6>[ 3.611093] ehci-exynos: EHCI Exynos driver <6>[ 3.615719] ehci-atmel: EHCI Atmel driver <6>[ 3.620173] tegra-ehci: Tegra EHCI driver <6>[ 3.624704] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 3.631187] ohci-pci: OHCI PCI platform driver <6>[ 3.635938] ohci-platform: OHCI generic platform driver <6>[ 3.641705] SPEAr-ohci: OHCI SPEAr driver <6>[ 3.646171] ohci-st: OHCI STMicroelectronics driver <6>[ 3.651530] ohci-atmel: OHCI Atmel driver <6>[ 3.656879] usbcore: registered new interface driver usb-storage <6>[ 3.671238] i2c /dev entries driver <6>[ 3.694154] sdhci: Secure Digital Host Controller Interface driver <6>[ 3.700607] sdhci: Copyright(c) Pierre Ossman <6>[ 3.707920] Synopsys Designware Multimedia Card Interface Driver <6>[ 3.716113] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 3.723347] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO <6>[ 3.727450] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO <6>[ 3.728636] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO <6>[ 3.739408] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 3.746751] usbcore: registered new interface driver usbhid <6>[ 3.752615] usbhid: USB HID core driver <6>[ 3.760974] ata1: SATA link down (SStatus 0 SControl 300) <6>[ 3.763203] NET: Registered protocol family 10 <6>[ 3.766688] ahci-imx 2200000.sata: no device found, disabling link. <6>[ 3.770716] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA <6>[ 3.772240] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA <6>[ 3.772406] Segment Routing with IPv6 <6>[ 3.772482] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 3.773054] NET: Registered protocol family 17 <6>[ 3.773066] can: controller area network core <6>[ 3.773137] NET: Registered protocol family 29 <6>[ 3.773142] can: raw protocol <6>[ 3.773149] can: broadcast manager protocol <6>[ 3.773159] can: netlink gateway - max_hops=1 <5>[ 3.773560] Key type dns_resolver registered <6>[ 3.777925] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug <6>[ 3.779834] ThumbEE CPU extension supported. <6>[ 3.820581] mmc2: new high speed SDHC card at address aaaa <5>[ 3.824196] Registering SWP/SWPB emulation handler <6>[ 3.829599] mmcblk2: mmc2:aaaa SL16G 14.8 GiB <5>[ 3.833685] Loading compiled-in X.509 certificates <4>[ 3.848615] GPT:Primary header thinks Alt. header is not at the end of the disk. <6>[ 3.856176] pstore: Using crash dump compression: deflate <4>[ 3.856188] GPT:29296874 != 31116287 <4>[ 3.856202] GPT:Alternate GPT header not at the end of the disk. <4>[ 3.882763] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 3.883231] GPT:29296874 != 31116287 <4>[ 3.889610] panel-simple panel-lcd: Specify missing connector_type <4>[ 3.897237] GPT: Use GNU Parted to correct GPT errors. <6>[ 3.897284] mmcblk2: p1 p2 p3 <4>[ 3.902586] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 3.932528] imx_usb 2184200.usb: No over current polarity defined <6>[ 3.942385] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 3.947557] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 3.981050] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 3.988082] hub 1-0:1.0: USB hub found <6>[ 3.992178] hub 1-0:1.0: 1 port detected <6>[ 3.998803] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 4.014904] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.023026] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.030984] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 4.043159] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.051075] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.058899] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.068940] input: gpio-keys as /devices/platform/gpio-keys/input/input0 <4>[ 4.081142] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.089014] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.096942] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 4.111250] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) <6>[ 4.320976] usb 1-1: new high-speed USB device number 2 using ci_hdrc <6>[ 4.522614] hub 1-1:1.0: USB hub found <6>[ 4.526842] hub 1-1:1.0: 3 ports detected <4>[ 4.537419] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 4.545403] panel-simple panel-lcd: Specify missing connector_type <4>[ 4.553663] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 7.281390] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off <6>[ 7.301008] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 7.330966] Sending DHCP requests ., OK <6>[ 7.375167] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.33 <6>[ 7.383497] IP-Config: Complete: <6>[ 7.387019] device=eth0, hwaddr=00:19:b8:08:f1:13, ipaddr=192.168.201.33, mask=255.255.255.0, gw=192.168.201.1 <6>[ 7.397784] host=imx6q-sabrelite-lava-cbg-3, domain=lava-rack, nis-domain=(none) <6>[ 7.405935] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= <6>[ 7.405947] nameserver0=192.168.201.1 <6>[ 7.426720] Freeing unused kernel memory: 2048K <6>[ 7.461353] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <6>[ 8.295336] imx-ipuv3 2400000.ipu: IPUv3H probed <4>[ 8.305901] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.313870] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.340268] imx-ipuv3 2800000.ipu: IPUv3H probed <4>[ 8.359771] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.378602] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.387411] panel-simple panel-lcd: Specify missing connector_type <6>[ 8.387650] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.402531] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.411158] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.419759] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.425379] panel-simple panel-lvds0: supply power not found, using dummy regulator <4>[ 8.448578] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.456641] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.470790] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.498127] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.509975] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.521646] caam 2100000.crypto: Entropy delay = 3200 <6>[ 8.521787] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) <6>[ 8.533860] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 <6>[ 8.583701] sgtl5000 0-000a: sgtl5000 revision 0x11 <6>[ 8.587768] caam 2100000.crypto: Instantiated RNG4 SH0 <6>[ 8.606411] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum <4>[ 8.616852] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator <4>[ 8.625103] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests <4>[ 8.633838] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator <4>[ 8.642031] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests <6>[ 8.648526] caam 2100000.crypto: Instantiated RNG4 SH1 <6>[ 8.655912] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) <6>[ 8.662819] caam 2100000.crypto: job rings = 2, qi = 0 <6>[ 8.668882] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 <6>[ 8.675410] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 <6>[ 8.681842] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 <6>[ 8.689200] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 <6>[ 8.698594] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.707191] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.715794] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.724388] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <4>[ 8.735079] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 8.743221] panel-simple panel-lcd: Specify missing connector_type <4>[ 8.751933] panel-simple panel-lvds0: supply power not found, using dummy regulator <6>[ 8.772236] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) <6>[ 8.780762] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) <6>[ 8.789349] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) <6>[ 8.797886] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) <6>[ 9.166000] caam algorithms registered in /proc/crypto <6>[ 9.172884] caam 2100000.crypto: registering rng-caam <4>[ 9.179852] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.187809] panel-simple panel-lcd: Specify missing connector_type <4>[ 9.196147] panel-simple panel-lvds0: supply power not found, using dummy regulator Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting<6>[ 9.211797] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) root file system ... Begin: Runn<6>[ 9.221981] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) ing /scripts/nfs-top ... done. B<6>[ 9.233287] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) egin: Running /scripts/nfs-premou<6>[ 9.244590] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) nt ... done. <4>[ 9.258378] panel-simple panel-lcd: supply power not found, using dummy regulator <4>[ 9.266434] panel-simple panel-lcd: Specify missing connector_type <5>[ 9.360606] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:13 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.33 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-3 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 10.414766] systemd[1]: System time before build time, advancing clock. <30>[ 10.492662] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 10.516800] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! <30>[ 10.563965] systemd[1]: Set hostname to . <30>[ 11.646143] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 11.655625] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 11.668429] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 11.678053] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-getty.slice. <30>[ 11.712726] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-modprobe.slice. <30>[ 11.752408] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice system-serial\x2dgetty.slice. <30>[ 11.791946] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. <30>[ 11.831917] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ OK ] Started Dispatch Password …ts to Console Directory Watch. <30>[ 11.871325] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. <30>[ 11.911609] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 11.924371] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached target Local Encrypted Volumes. <30>[ 11.961953] systemd[1]: Reached target Paths. [ OK ] Reached target Paths. <30>[ 11.991157] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Remote File Systems. <30>[ 12.031325] systemd[1]: Reached target Slices. [ OK ] Reached target Slices. <30>[ 12.061514] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. <30>[ 12.092244] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on initctl Compatibility Named Pipe. <30>[ 12.168022] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 12.178344] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). <30>[ 12.212613] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. <30>[ 12.253598] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. <30>[ 12.295126] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Control Socket. <30>[ 12.331714] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. <30>[ 12.372285] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 12.381849] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 12.394831] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... <30>[ 12.434844] systemd[1]: Mounting Kernel Trace File System... Mounting Kernel Trace File System... <30>[ 12.475485] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting Create list of st…odes for the current kernel... <30>[ 12.514601] systemd[1]: Starting Load Kernel Module configfs... Starting Load Kernel Module configfs... <30>[ 12.544338] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module drm... <30>[ 12.587605] systemd[1]: Starting Load Kernel Module fuse... Starting Load Kernel Module fuse... <30>[ 12.635706] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 12.648765] systemd[1]: Starting Journal Service... Starting Journal Service... <30>[ 12.689796] systemd[1]: Starting Load Kernel Modules... Starting Load Kernel Modules... <30>[ 12.734855] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Remount Root and Kernel File Systems... <30>[ 12.774214] systemd[1]: Starting Coldplug All udev Devices... Starting Coldplug All udev Devices... <30>[ 12.827131] systemd[1]: Mounted Kernel Debug File System. [ OK ] Mounted Kernel Debug File System. <30>[ 12.861582] systemd[1]: Mounted Kernel Trace File System. [ OK ] Mounted Kernel Trace File System. <30>[ 12.912201] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished Create list of st… nodes for the current kernel. <30>[ 12.981359] systemd[1]: Started Journal Service. [ OK ] Started Journal Service. [ OK ] Finished Load Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... <46>[ 13.305024] systemd-journald[256]: Received client request to flush runtime journal. Starting Apply Kernel Variables... Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Coldplug All udev Devices. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Started Rule-based Manager for Device Events and Files. [ OK ] Finished Create Volatile Files and Directories. Starting Network Service... Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Started Network Name Resolution. [ OK ] Found device /dev/ttymxc1. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.147-cip18 #1 SMP Tue Nov 8 19:33:57 UTC 2022 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/7902672/extract-nfsrootfs-r0qgd4lu' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/7902672/extract-nfsrootfs-r0qgd4lu' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-7902672/environment . /lava-7902672/environment / # /lava-7902672/bin/lava-test-runner /lava-7902672/0 /lava-7902672/bin/lava-test-runner /lava-7902672/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-7902672/0/tests/0_timesync-off ++ cat uuid + UUID=7902672_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-7902672/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=7902672_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s false -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.147-cip18-15-gef247a3cd0ad/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ INFO: Generating a skipfile based on /lava-7902672/0/tests/1_kselftest-filesystems/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: Installing sed perl wget xz-utils iproute2 Hit:1 http://deb.debian.org/debian bullseye InRelease Reading package lists... Reading package lists... Building dependency tree... Reading state information... iproute2 is already the newest version (5.10.0-4). perl is already the newest version (5.32.1-4+deb11u2). sed is already the newest version (4.7-1). wget is already the newest version (1.21-1+deb11u1). xz-utils is already the newest version (5.2.5-2.1~deb11u1). 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. --2022-11-08 19:57:09-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.147-cip18-15-gef247a3cd0ad/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1408972 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 45.91K 135KB/s kselftest.tar.xz 5%[> ] 74.19K 128KB/s kselftest.tar.xz 11%[=> ] 160.93K 185KB/s kselftest.tar.xz 13%[=> ] 187.32K 162KB/s kselftest.tar.xz 16%[==> ] 228.32K 158KB/s kselftest.tar.xz 18%[==> ] 259.92K 157KB/s kselftest.tar.xz 20%[===> ] 282.54K 150KB/s kselftest.tar.xz 22%[===> ] 303.75K 146KB/s kselftest.tar.xz 23%[===> ] 326.38K 141KB/s kselftest.tar.xz 25%[====> ] 349.00K 138KB/s kselftest.tar.xz 27%[====> ] 379.63K 131KB/s kselftest.tar.xz 29%[====> ] 406.98K 131KB/s eta 7s kselftest.tar.xz 31%[=====> ] 428.19K 128KB/s eta 7s kselftest.tar.xz 32%[=====> ] 443.26K 124KB/s eta 7s kselftest.tar.xz 33%[=====> ] 464.96K 121KB/s eta 7s kselftest.tar.xz 35%[======> ] 486.17K 120KB/s eta 7s kselftest.tar.xz 36%[======> ] 503.14K 118KB/s eta 7s kselftest.tar.xz 38%[======> ] 528.59K 117KB/s eta 7s kselftest.tar.xz 39%[======> ] 546.97K 116KB/s eta 7s kselftest.tar.xz 41%[=======> ] 576.18K 112KB/s eta 7s kselftest.tar.xz 43%[=======> ] 600.71K 98.5KB/s eta 7s kselftest.tar.xz 44%[=======> ] 619.09K 98.5KB/s eta 7s kselftest.tar.xz 46%[========> ] 644.54K 96.4KB/s eta 7s kselftest.tar.xz 48%[========> ] 664.34K 93.4KB/s eta 7s kselftest.tar.xz 50%[=========> ] 694.96K 92.3KB/s eta 6s kselftest.tar.xz 52%[=========> ] 718.07K 92.4KB/s eta 6s kselftest.tar.xz 53%[=========> ] 733.14K 89.8KB/s eta 6s kselftest.tar.xz 55%[==========> ] 757.67K 90.0KB/s eta 6s kselftest.tar.xz 56%[==========> ] 775.57K 85.5KB/s eta 6s kselftest.tar.xz 57%[==========> ] 790.19K 83.7KB/s eta 6s kselftest.tar.xz 58%[==========> ] 804.33K 83.7KB/s eta 6s kselftest.tar.xz 59%[==========> ] 825.54K 82.3KB/s eta 6s kselftest.tar.xz 61%[===========> ] 848.17K 81.2KB/s eta 5s kselftest.tar.xz 63%[===========> ] 870.79K 80.6KB/s eta 5s kselftest.tar.xz 65%[============> ] 896.25K 80.9KB/s eta 5s kselftest.tar.xz 66%[============> ] 911.32K 78.4KB/s eta 5s kselftest.tar.xz 67%[============> ] 934.42K 76.5KB/s eta 5s kselftest.tar.xz 69%[============> ] 954.22K 76.8KB/s eta 5s kselftest.tar.xz 70%[=============> ] 969.29K 73.9KB/s eta 5s kselftest.tar.xz 72%[=============> ] 992.40K 72.9KB/s eta 5s kselftest.tar.xz 73%[=============> ] 1009K 73.1KB/s eta 4s kselftest.tar.xz 74%[=============> ] 1.00M 72.7KB/s eta 4s kselftest.tar.xz 76%[==============> ] 1.03M 72.8KB/s eta 4s kselftest.tar.xz 77%[==============> ] 1.05M 72.2KB/s eta 4s kselftest.tar.xz 79%[==============> ] 1.06M 72.3KB/s eta 3s kselftest.tar.xz 80%[===============> ] 1.08M 72.3KB/s eta 3s kselftest.tar.xz 81%[===============> ] 1.10M 72.2KB/s eta 3s kselftest.tar.xz 83%[===============> ] 1.12M 72.5KB/s eta 3s kselftest.tar.xz 84%[===============> ] 1.14M 72.9KB/s eta 2s kselftest.tar.xz 86%[================> ] 1.16M 70.9KB/s eta 2s kselftest.tar.xz 87%[================> ] 1.17M 70.1KB/s eta 2s kselftest.tar.xz 88%[================> ] 1.19M 70.9KB/s eta 2s kselftest.tar.xz 90%[=================> ] 1.21M 69.9KB/s eta 2s kselftest.tar.xz 91%[=================> ] 1.23M 69.7KB/s eta 2s kselftest.tar.xz 92%[=================> ] 1.25M 69.2KB/s eta 2s kselftest.tar.xz 94%[=================> ] 1.27M 70.5KB/s eta 2s kselftest.tar.xz 95%[==================> ] 1.28M 68.8KB/s eta 1s kselftest.tar.xz 96%[==================> ] 1.30M 69.2KB/s eta 1s kselftest.tar.xz 98%[==================> ] 1.32M 70.1KB/s eta 1s kselftest.tar.xz 99%[==================> ] 1.34M 70.9KB/s eta 1s kselftest.tar.xz 100%[===================>] 1.34M 71.2KB/s in 16s 2022-11-08 19:57:25 (87.2 KB/s) - 'kselftest.tar.xz' saved [1408972/1408972] skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== <12>[ 62.486551] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #