Connected to r8a774a1-hihope-rzg2m-ex-01 console [channel connected] (~$quit to exit)
[    0.000161] NOTICE:  BL2: RZ G2M Initial Program Loader(CA57)
[    0.004424] NOTICE:  BL2: Initial Program Loader(Rev.2.0.4)
[    0.009955] NOTICE:  BL2: PRR is RZG G2M Ver.1.3
[    0.014540] NOTICE:  BL2: Board is HiHope RZ/G2M Rev.1.0
[    0.019805] NOTICE:  BL2: Boot device is QSPI Flash(40MHz)
[    0.025247] NOTICE:  BL2: LCM state is unknown
[    0.029658] NOTICE:  BL2: DDR3200(rev.0.37)
[    0.040927] NOTICE:  BL2: [COLD_BOOT]
[    0.046695] NOTICE:  BL2: DRAM Split is 2ch
[    0.049390] NOTICE:  BL2: QoS is default setting(rev.0.19)
[    0.054833] NOTICE:  BL2: DRAM refresh interval 1.95 usec
[    0.060190] NOTICE:  BL2: Periodic Write DQ Training
[    0.065217] NOTICE:  BL2: Lossy Decomp areas
[    0.069348] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
[    0.076433] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
[    0.083345] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
[    0.090260] NOTICE:  BL2: v1.5(release):236f8fb-dirty
[    0.095268] NOTICE:  BL2: Built : 05:03:06, Oct 21 2019
[    0.100453] NOTICE:  BL2: Normal boot
[    0.104096] NOTICE:  BL2: dst=0xe6322100 src=0x8180000 len=512(0x200)
[    0.110585] NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
[    0.118313] NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
[    0.137226] NOTICE:  BL2: dst=0x50000000 src=0x8300000 len=1048576(0x100000)
[    0.357484] NOTICE:  BL2: Booting BL31


U-Boot 2018.09 (Oct 21 2019 - 01:43:31 +0000)

CPU: Renesas Electronics R8A774A1 rev 1.3
Model: Hoperun Technology HiHope RZ/G2M platform (hihope-rzg2m)
DRAM:  3.9 GiB
Bank #0: 0x048000000 - 0x0bfffffff, 1.9 GiB
Bank #1: 0x600000000 - 0x67fffffff, 2 GiB

Error reading output register
Error reading output register
Error reading output register
Error reading output register
MMC:   sd@ee100000: 0, sd@ee160000: 1
Loading Environment from MMC... OK
In:    serial@e6e88000
Out:   serial@e6e88000
Err:   serial@e6e88000
Net:   eth0: ethernet@e6800000
Hit any key to stop autoboot:  2 
 0 
=> setenv autoload no
setenv autoload no
=> setenv initrd_high 0xffffffff
setenv initrd_high 0xffffffff
=> setenv fdt_high 0xffffffff
setenv fdt_high 0xffffffff
=> dhcp
dhcp
ethernet@e6800000 Waiting for PHY auto negotiation to complete... done
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
DHCP client bound to address 192.168.1.71 (1211 ms)
=> setenv serverip 192.168.1.1
setenv serverip 192.168.1.1
=> tftp 0x48080000 834185/tftp-deploy-isuaatyh/kernel/Image
tftp 0x48080000 834185/tftp-deploy-isuaatyh/kernel/Image
Using ethernet@e6800000 device
TFTP from server 192.168.1.1; our IP address is 192.168.1.71
Filename '834185/tftp-deploy-isuaatyh/kernel/Image'.
Load address: 0x48080000
Loading: *#################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 #################################################################
	 ##########################T T T T T T T T T T 
Retry count exceeded; starting again
=>