Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 16 GB DDR4, 64-bit, CL=13, ECC on, 256B, CS0+CS1 NOTICE: UDIMM 18ASF1G72AZ-2G1A1 NOTICE: 4 GB DDR4, 32-bit, CL=11, ECC on, CS0+CS1 NOTICE: BL2: v1.5(release):LSDK-19.06 NOTICE: BL2: Built : 20:57:22, Jun 27 2019 NOTICE: BL2: Booting BL31NOTICE: BL31: v1.5(release):LSDK-19.06 NOTICE: BL31: Built : 20:57:30, Jun 27 2019 NOTICE: Welcome to LS2088 BL31 Phase U-Boot 2019.04-gc873063750 (Jun 27 2019 - 18:08:01 +0800) SoC: LS2088AE Rev1.0 (0x87090010) Clock Configuration: CPU0(A72):1800 MHz CPU1(A72):1800 MHz CPU2(A72):1800 MHz CPU3(A72):1800 MHz CPU4(A72):1800 MHz CPU5(A72):1800 MHz CPU6(A72):1800 MHz CPU7(A72):1800 MHz Bus: 700 MHz DDR: 1866.667 MT/s DP-DDR: 1600 MT/s Reset Configuration Word (RCW): 00000000: 483038b8 48480048 00000000 00000000 00000010: 00000000 00000000 00a00000 00000000 00000020: 01e01180 00002581 00000000 00000000 00000030: 00400c0b 00000000 00000000 00000000 00000040: 00000000 00000000 00000000 00000000 00000050: 00000000 00000000 00000000 00000000 00000060: 00000000 00000000 00027000 00000000 00000070: 412a0000 00040000 Model: Freescale Layerscape 2080a RDB Board Board: LS2088AE Rev1.0-RDB, Board Arch: V1, Board version: D, boot from vBank: 0 FPGA: v1.18 SERDES1 Reference : Clock1 = 156.25MHz Clock2 = 156.25MHz SERDES2 Reference : Clock1 = 100MHz Clock2 = 100MHz I2C: ready DRAM: 15.9 GiB DDR 15.9 GiB (DDR4, 64-bit, CL=13, ECC on) DDR Controller Interleaving Mode: 256B DDR Chip-Select Interleaving Mode: CS0+CS1 SEC0: RNG instantiated SEC0: RNG instantiated Using SERDES1 Protocol: 42 (0x2a) Using SERDES2 Protocol: 65 (0x41) Flash: 128 MiB NAND: 2048 MiB MMC: FSL_SDHC: 0 Loading Environment from Flash... OK EEPROM: Invalid ID (ff ff ff ff) In: serial Out: serial Err: serial VID: Core voltage after adjustment is at 1000 mV Net: DPMAC5@xgmii running firmware version 2.3.5 DPMAC5@xgmii: system interface XFI DPMAC5@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC6@xgmii running firmware version 2.3.5 DPMAC6@xgmii: system interface XFI DPMAC6@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC7@xgmii running firmware version 2.3.5 DPMAC7@xgmii: system interface XFI DPMAC7@xgmii: Aquantia AQR405 Firmware Version 2.3.5 DPMAC8@xgmii running firmware version 2.3.5 DPMAC8@xgmii: system interface XFI DPMAC8@xgmii: Aquantia AQR405 Firmware Version 2.3.5 PCIe0: pcie@3400000 disabled PCIe1: pcie@3500000 disabled PCIe2: pcie@3600000 Root Complex: x1 gen1 PCIe3: pcie@3700000 Root Complex: no link e1000: 68:05:ca:3f:90:5c DPMAC1@xgmii Warning: DPMAC1@xgmii (eth0) using random MAC address - d6:15:34:f0:d1:b2 , DPMAC2@xgmii Warning: DPMAC2@xgmii (eth1) using random MAC address - de:1d:1d:8a:5d:be , DPMAC3@xgmii Warning: DPMAC3@xgmii (eth2) using random MAC address - 86:e0:48:96:e6:2f , DPMAC4@xgmii Warning: DPMAC4@xgmii (eth3) using random MAC address - 8e:e8:61:ec:6a:23 , DPMAC5@xgmii Warning: DPMAC5@xgmii (eth4) using random MAC address - b6:b3:9c:4c:83:2b , DPMAC6@xgmii Warning: DPMAC6@xgmii (eth5) using random MAC address - be:bb:b5:36:0f:27 , DPMAC7@xgmii Warning: DPMAC7@xgmii (eth6) using random MAC address - 22:0a:b8:e3:52:72 , DPMAC8@xgmii Warning: DPMAC8@xgmii (eth7) using random MAC address - 4a:01:d6:d0:15:8d , e1000#0 [PRIME] crc32+ fsl-mc: Booting Management Complex ... SUCCESS fsl-mc: Management Complex booted (version: 10.16.2, boot status: 0x1) Hit any key to stop autoboot: 10  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffffffffffff setenv initrd_high 0xffffffffffffffff => setenv fdt_high 0xffffffffffffffff setenv fdt_high 0xffffffffffffffff => setenv ipaddr 172.16.1.14; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 setenv ipaddr 172.16.1.14; setenv serverip 172.16.1.4; setenv ethact e1000#0; setenv ethprime e1000#0 => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80080000 1147066/tftp-deploy-yutzk7f4/kernel/uImage tftp 0x80080000 1147066/tftp-deploy-yutzk7f4/kernel/uImage Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1147066/tftp-deploy-yutzk7f4/kernel/uImage'. Load address: 0x80080000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################### 3.9 MiB/s done Bytes transferred = 31844928 (1e5ea40 hex) => tftp 0x91000000 1147066/tftp-deploy-yutzk7f4/ramdisk/ramdisk.cpio.gz.uboot tftp 0x91000000 1147066/tftp-deploy-yutzk7f4/ramdisk/ramdisk.cpio.gz.uboot Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1147066/tftp-deploy-yutzk7f4/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x91000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ###################################################### 2.7 MiB/s done Bytes transferred = 18909329 (1208891 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x90000000 1147066/tftp-deploy-yutzk7f4/dtb/fsl-ls2088a-rdb.dtb tftp 0x90000000 1147066/tftp-deploy-yutzk7f4/dtb/fsl-ls2088a-rdb.dtb Using e1000#0 device TFTP from server 59.144.98.45; our IP address is 172.16.1.14 Filename '1147066/tftp-deploy-yutzk7f4/dtb/fsl-ls2088a-rdb.dtb'. Load address: 0x90000000 Loading: *## 2.9 KiB/s done Bytes transferred = 19637 (4cb5 hex) => setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' setenv bootargs 'console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp' => bootm 0x80080000 0x91000000 0x90000000 bootm 0x80080000 0x91000000 0x90000000 ## Booting kernel from Legacy Image at 80080000 ... Image Name: Created: 2023-07-12 8:50:58 UTC Image Type: AArch64 Linux Kernel Image (uncompressed) Data Size: 31844864 Bytes = 30.4 MiB Load Address: 80080000 Entry Point: 80080000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 91000000 ... Image Name: Created: 2023-07-12 8:51:02 UTC Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 18909265 Bytes = 18 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 90000000 Booting using the fdt blob at 0x90000000 Loading Kernel Image ... OK Using Device Tree in place at 0000000090000000, end 0000000090007cb4 fsl-mc: DPL not deployed, DPAA2 ethernet not work Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd082] [ 0.000000] Linux version 5.10.162-cip24-rt10 (KernelCI@build-j926912-arm64-gcc-10-defconfig-7x7qh) (aarch64-linux-gnu-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP PREEMPT Thu Jan 26 23:56:09 UTC 2023 [ 0.000000] Machine model: Freescale Layerscape 2088A RDB Board [ 0.000000] earlycon: uart8250 at MMIO 0x00000000021c0600 (options '') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader! [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x837e3f7b00-0x837e3f9fff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x000000837fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x00000000fbdfffff] [ 0.000000] node 0: [mem 0x0000008080000000-0x000000837fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000837fffffff] [ 0.000000] On node 0 totalpages: 3653120 [ 0.000000] DMA zone: 8192 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 507392 pages, LIFO batch:63 [ 0.000000] Normal zone: 49152 pages used for memmap [ 0.000000] Normal zone: 3145728 pages, LIFO batch:63 [ 0.000000] cma: Reserved 32 MiB at 0x00000000f9c00000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 19 pages/cpu s40344 r8192 d29288 u77824 [ 0.000000] pcpu-alloc: s40344 r8192 d29288 u77824 alloc=19*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: detected: EL2 vector hardening [ 0.000000] CPU features: kernel page table isolation forced ON by KASLR [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] CPU features: detected: Spectre-v2 [ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: detected: ARM erratum 1742098 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 3595776 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: console=ttyS1,115200n8 root=/dev/ram0 earlycon=uart8250,mmio,0x21c0600 nousb default_hugepagesz=2m hugepagesz=2m hugepages=256 arm-smmu-mod.disable_bypass=n arm-smmu.disable_bypass=n ip=dhcp [ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000f5c00000-0x00000000f9c00000] (64MB) [ 0.000000] Memory: 14180336K/14612480K available (14528K kernel code, 2874K rwdata, 7608K rodata, 5952K init, 502K bss, 399376K reserved, 32768K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 256 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: 16 PPIs implemented [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000006100000 [ 0.000000] ITS [mem 0x06020000-0x0603ffff] [ 0.000000] ITS@0x0000000006020000: allocated 8192 Devices @8080050000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GICv3: using LPI property table @0x0000008080060000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000008080070000 [ 0.000000] arch_timer: Enabling global workaround for Freescale erratum a005858 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 25.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5c409fb33, max_idle_ns: 440795203156 ns [ 0.000000] sched_clock: 56 bits at 25MHz, resolution 39ns, wraps every 4398046511103ns [ 0.008277] Console: colour dummy device 80x25 [ 0.012783] Calibrating delay loop (skipped), value calculated using timer frequency.. 50.00 BogoMIPS (lpj=100000) [ 0.023198] pid_max: default: 32768 minimum: 301 [ 0.027871] LSM: Security Framework initializing [ 0.032581] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.040240] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.048966] rcu: Hierarchical SRCU implementation. [ 0.053886] Platform MSI: gic-its@6020000 domain created [ 0.059273] PCI/MSI: /interrupt-controller@6000000/gic-its@6020000 domain created [ 0.066837] fsl-mc MSI: gic-its@6020000 domain created [ 0.072454] EFI services will not be available. [ 0.077189] smp: Bringing up secondary CPUs ... [ 0.081966] Detected PIPT I-cache on CPU1 [ 0.086009] GICv3: CPU1: found redistributor 1 region 0:0x0000000006120000 [ 0.092931] GICv3: CPU1: using allocated LPI pending table @0x0000008080080000 [ 0.100208] arch_timer: CPU1: Trapping CNTVCT access [ 0.105205] CPU1: Booted secondary processor 0x0000000001 [0x410fd082] [ 0.112029] Detected PIPT I-cache on CPU2 [ 0.116071] GICv3: CPU2: found redistributor 100 region 0:0x0000000006140000 [ 0.123164] GICv3: CPU2: using allocated LPI pending table @0x0000008080090000 [ 0.130435] arch_timer: CPU2: Trapping CNTVCT access [ 0.135427] CPU2: Booted secondary processor 0x0000000100 [0x410fd082] [ 0.142249] Detected PIPT I-cache on CPU3 [ 0.146282] GICv3: CPU3: found redistributor 101 region 0:0x0000000006160000 [ 0.153372] GICv3: CPU3: using allocated LPI pending table @0x00000080800a0000 [ 0.160639] arch_timer: CPU3: Trapping CNTVCT access [ 0.165630] CPU3: Booted secondary processor 0x0000000101 [0x410fd082] [ 0.172441] Detected PIPT I-cache on CPU4 [ 0.176481] GICv3: CPU4: found redistributor 200 region 0:0x0000000006180000 [ 0.183571] GICv3: CPU4: using allocated LPI pending table @0x00000080800b0000 [ 0.190842] arch_timer: CPU4: Trapping CNTVCT access [ 0.195834] CPU4: Booted secondary processor 0x0000000200 [0x410fd082] [ 0.202659] Detected PIPT I-cache on CPU5 [ 0.206692] GICv3: CPU5: found redistributor 201 region 0:0x00000000061a0000 [ 0.213781] GICv3: CPU5: using allocated LPI pending table @0x00000080800c0000 [ 0.221048] arch_timer: CPU5: Trapping CNTVCT access [ 0.226039] CPU5: Booted secondary processor 0x0000000201 [0x410fd082] [ 0.232854] Detected PIPT I-cache on CPU6 [ 0.236898] GICv3: CPU6: found redistributor 300 region 0:0x00000000061c0000 [ 0.243995] GICv3: CPU6: using allocated LPI pending table @0x00000080800d0000 [ 0.251268] arch_timer: CPU6: Trapping CNTVCT access [ 0.256262] CPU6: Booted secondary processor 0x0000000300 [0x410fd082] [ 0.263083] Detected PIPT I-cache on CPU7 [ 0.267118] GICv3: CPU7: found redistributor 301 region 0:0x00000000061e0000 [ 0.274213] GICv3: CPU7: using allocated LPI pending table @0x00000080800e0000 [ 0.281484] arch_timer: CPU7: Trapping CNTVCT access [ 0.286480] CPU7: Booted secondary processor 0x0000000301 [0x410fd082] [ 0.293088] smp: Brought up 1 node, 8 CPUs [ 0.297216] SMP: Total of 8 processors activated. [ 0.301948] CPU features: detected: 32-bit EL0 Support [ 0.307124] CPU features: detected: CRC32 instructions [ 0.312294] CPU features: detected: 32-bit EL1 Support [ 0.328910] CPU: All CPU(s) started at EL2 [ 0.333057] alternatives: patching kernel code [ 0.338216] devtmpfs: initialized [ 0.342887] KASLR enabled [ 0.345587] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.355400] futex hash table entries: 2048 (order: 5, 131072 bytes, linear) [ 0.362780] pinctrl core: initialized pinctrl subsystem [ 0.368479] DMI not present or invalid. [ 0.372620] NET: Registered protocol family 16 [ 0.377780] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.385266] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.393605] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.401674] audit: initializing netlink subsys (disabled) [ 0.407190] audit: type=2000 audit(0.336:1): state=initialized audit_enabled=0 res=1 [ 0.407518] thermal_sys: Registered thermal governor 'step_wise' [ 0.407521] thermal_sys: Registered thermal governor 'power_allocator' [ 0.414984] cpuidle: using governor menu [ 0.431598] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.438507] ASID allocator initialised with 32768 entries [ 0.444389] Serial: AMBA PL011 UART driver [ 0.455576] Machine: Freescale Layerscape 2088A RDB Board [ 0.461011] SoC family: QorIQ LS2088A [ 0.464687] SoC ID: svr:0x87090010, Revision: 1.0 [ 0.477224] HugeTLB registered 2.00 MiB page size, pre-allocated 256 pages [ 0.484169] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.490914] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.497671] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.505057] cryptd: max_cpu_qlen set to 1000 [ 0.510453] ACPI: Interpreter disabled. [ 0.514956] iommu: Default domain type: Translated [ 0.519925] vgaarb: loaded [ 0.522752] SCSI subsystem initialized [ 0.526585] libata version 3.00 loaded. [ 0.530516] usbcore: registered new interface driver usbfs [ 0.536048] usbcore: registered new interface driver hub [ 0.541406] usbcore: registered new device driver usb [ 0.546685] imx-i2c 2000000.i2c: can't get pinctrl, bus recovery not supported [ 0.554074] i2c i2c-0: IMX I2C adapter registered [ 0.558954] pps_core: LinuxPPS API ver. 1 registered [ 0.563949] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.573155] PTP clock support registered [ 0.577139] EDAC MC: Ver: 3.0.0 [ 0.580779] fsl-ifc 2240000.ifc: Freescale Integrated Flash Controller [ 0.587362] fsl-ifc 2240000.ifc: IFC version 2.0, 8 banks [ 0.592867] FPGA manager framework [ 0.596309] Advanced Linux Sound Architecture Driver Initialized. [ 0.602751] clocksource: Switched to clocksource arch_sys_counter [ 0.608967] VFS: Disk quotas dquot_6.6.0 [ 0.612935] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.619926] pnp: PnP ACPI: disabled [ 0.625879] NET: Registered protocol family 2 [ 0.630679] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.641744] tcp_listen_portaddr_hash hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.650536] TCP established hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.659132] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear) [ 0.667032] TCP: Hash tables configured (established 131072 bind 65536) [ 0.673776] UDP hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.680781] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes, linear) [ 0.688296] NET: Registered protocol family 1 [ 0.692867] RPC: Registered named UNIX socket transport module. [ 0.698827] RPC: Registered udp transport module. [ 0.703557] RPC: Registered tcp transport module. [ 0.708286] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.714768] PCI: CLS 0 bytes, default 64 [ 0.718781] Unpacking initramfs... [ 1.174835] Freeing initrd memory: 18460K [ 1.179304] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.187264] kvm [1]: IPA Size Limit: 44 bits [ 1.192023] kvm [1]: vgic-v2@c0e0000 [ 1.195649] kvm [1]: GIC system register CPU interface enabled [ 1.201615] kvm [1]: vgic interrupt IRQ9 [ 1.205665] kvm [1]: Hyp mode initialized successfully [ 1.212680] Initialise system trusted keyrings [ 1.217218] workingset: timestamp_bits=42 max_order=22 bucket_order=0 [ 1.225990] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.232113] NFS: Registering the id_resolver key type [ 1.237211] Key type id_resolver registered [ 1.241418] Key type id_legacy registered [ 1.245477] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 1.252226] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 1.259728] 9p: Installing v9fs 9p2000 file system support [ 1.286912] Key type asymmetric registered [ 1.291032] Asymmetric key parser 'x509' registered [ 1.295947] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 1.303391] io scheduler mq-deadline registered [ 1.307943] io scheduler kyber registered [ 1.315618] layerscape-pcie 3600000.pcie: host bridge /soc/pcie@3600000 ranges: [ 1.323000] layerscape-pcie 3600000.pcie: IO 0x3000010000..0x300001ffff -> 0x0000000000 [ 1.331591] layerscape-pcie 3600000.pcie: MEM 0x3040000000..0x307fffffff -> 0x0040000000 [ 1.340249] layerscape-pcie 3600000.pcie: PCI host bridge to bus 0000:00 [ 1.346993] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.352511] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.358730] pci_bus 0000:00: root bus resource [mem 0x3040000000-0x307fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.369336] pci 0000:00:00.0: [1957:8240] type 01 class 0x060400 [ 1.375389] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00ffffff] [ 1.381698] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x03ffffff] [ 1.388007] pci 0000:00:00.0: reg 0x38: [mem 0x3048000000-0x3048ffffff pref] [ 1.395133] pci 0000:00:00.0: supports D1 D2 [ 1.399425] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot [ 1.406107] pci 0000:01:00.0: [8086:10d3] type 00 class 0x020000 [ 1.412219] pci 0000:01:00.0: reg 0x10: [mem 0x3049000000-0x304901ffff] [ 1.418913] pci 0000:01:00.0: reg 0x14: [mem 0x3049080000-0x30490fffff] [ 1.425602] pci 0000:01:00.0: reg 0x18: [io 0x1000-0x101f] [ 1.431245] pci 0000:01:00.0: reg 0x1c: [mem 0x3049100000-0x3049103fff] [ 1.438008] pci 0000:01:00.0: reg 0x30: [mem 0x3049140000-0x304917ffff pref] [ 1.445357] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 1.463233] pci 0000:00:00.0: BAR 1: assigned [mem 0x3040000000-0x3043ffffff] [ 1.470417] pci 0000:00:00.0: BAR 0: assigned [mem 0x3044000000-0x3044ffffff] [ 1.477602] pci 0000:00:00.0: BAR 6: assigned [mem 0x3045000000-0x3045ffffff pref] [ 1.485221] pci 0000:00:00.0: BAR 14: assigned [mem 0x3046000000-0x30460fffff] [ 1.492491] pci 0000:00:00.0: BAR 13: assigned [io 0x1000-0x1fff] [ 1.498712] pci 0000:01:00.0: BAR 1: assigned [mem 0x3046000000-0x304607ffff] [ 1.505906] pci 0000:01:00.0: BAR 6: assigned [mem 0x3046080000-0x30460bffff pref] [ 1.513525] pci 0000:01:00.0: BAR 0: assigned [mem 0x30460c0000-0x30460dffff] [ 1.520719] pci 0000:01:00.0: BAR 3: assigned [mem 0x30460e0000-0x30460e3fff] [ 1.527907] pci 0000:01:00.0: BAR 2: assigned [io 0x1000-0x101f] [ 1.534050] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.539305] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] [ 1.545439] pci 0000:00:00.0: bridge window [mem 0x3046000000-0x30460fffff] [ 1.552775] layerscape-pcie 3700000.pcie: host bridge /soc/pcie@3700000 ranges: [ 1.560146] layerscape-pcie 3700000.pcie: IO 0x3800010000..0x380001ffff -> 0x0000000000 [ 1.568737] layerscape-pcie 3700000.pcie: MEM 0x3840000000..0x387fffffff -> 0x0040000000 [ 1.577381] layerscape-pcie 3700000.pcie: PCI host bridge to bus 0001:00 [ 1.584129] pci_bus 0001:00: root bus resource [bus 00-ff] [ 1.589650] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x0000-0xffff]) [ 1.598667] pci_bus 0001:00: root bus resource [mem 0x3840000000-0x387fffffff] (bus address [0x40000000-0x7fffffff]) [ 1.609274] pci 0001:00:00.0: [1957:8240] type 01 class 0x060400 [ 1.615329] pci 0001:00:00.0: reg 0x38: [mem 0x3840000000-0x38400007ff pref] [ 1.622450] pci 0001:00:00.0: supports D1 D2 [ 1.626742] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot [ 1.633750] pci 0001:00:00.0: BAR 6: assigned [mem 0x3840000000-0x38400007ff pref] [ 1.641369] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 1.647129] EINJ: ACPI disabled. [ 1.655734] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.662949] 21c0500.serial: ttyS0 at MMIO 0x21c0500 (irq = 16, base_baud = 21875000) is a 16550A [ 1.672019] 21c0600.serial: ttyS1 at MMIO 0x21c0600 (irq = 16, base_baud = 21875000) is a 16550A [ 1.680918] printk: console [ttyS1] enabled [ 1.680918] printk: console [ttyS1] enabled [ 1.689302] printk: bootconsole [uart8250] disabled [ 1.689302] printk: bootconsole [uart8250] disabled [ 1.699292] 21d0500.serial: ttyS2 at MMIO 0x21d0500 (irq = 17, base_baud = 21875000) is a 16550A [ 1.708285] 21d0600.serial: ttyS3 at MMIO 0x21d0600 (irq = 17, base_baud = 21875000) is a 16550A [ 1.717276] SuperH (H)SCI(F) driver initialized [ 1.722003] msm_serial: driver initialized [ 1.726872] arm-smmu 5000000.iommu: probing hardware configuration... [ 1.733314] arm-smmu 5000000.iommu: SMMUv2 with: [ 1.737930] arm-smmu 5000000.iommu: stage 1 translation [ 1.743238] arm-smmu 5000000.iommu: stage 2 translation [ 1.748544] arm-smmu 5000000.iommu: nested translation [ 1.753765] arm-smmu 5000000.iommu: coherent table walk [ 1.759071] arm-smmu 5000000.iommu: stream matching with 128 register groups [ 1.766205] arm-smmu 5000000.iommu: 64 context banks (0 stage-2 only) [ 1.772733] arm-smmu 5000000.iommu: Supported page sizes: 0x61311000 [ 1.779172] arm-smmu 5000000.iommu: Stage-1: 48-bit VA -> 48-bit IPA [ 1.785608] arm-smmu 5000000.iommu: Stage-2: 48-bit IPA -> 48-bit PA [ 1.796090] loop: module loaded [ 1.799594] megasas: 07.714.04.00-rc1 [ 1.803714] ahci-qoriq 3200000.sata: supply ahci not found, using dummy regulator [ 1.811252] ahci-qoriq 3200000.sata: supply phy not found, using dummy regulator [ 1.818666] ahci-qoriq 3200000.sata: supply target not found, using dummy regulator [ 1.826371] ahci-qoriq 3200000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.835335] ahci-qoriq 3200000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.845519] scsi host0: ahci-qoriq [ 1.849028] ata1: SATA max UDMA/133 mmio [mem 0x03200000-0x0320ffff] port 0x100 irq 104 [ 1.857089] ahci-qoriq 3210000.sata: supply ahci not found, using dummy regulator [ 1.864614] ahci-qoriq 3210000.sata: supply phy not found, using dummy regulator [ 1.872025] ahci-qoriq 3210000.sata: supply target not found, using dummy regulator [ 1.879729] ahci-qoriq 3210000.sata: AHCI 0001.0301 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 1.888689] ahci-qoriq 3210000.sata: flags: 64bit ncq sntf pm clo only pmp fbs pio slum part ccc sds apst [ 1.898609] scsi host1: ahci-qoriq [ 1.902075] ata2: SATA max UDMA/133 mmio [mem 0x03210000-0x0321ffff] port 0x100 irq 105 [ 1.910361] physmap-flash 580000000.nor: physmap platform flash device: [mem 0x580000000-0x587ffffff] [ 1.919633] 580000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002801 [ 1.929722] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.934866] Amd/Fujitsu Extended Query version 1.5. [ 1.939915] number of CFI chips: 1 [ 1.959721] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x48 [ 1.966080] nand: Micron MT29F16G08ABABAWP [ 1.970183] nand: 2048 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224 [ 1.978960] Bad block table found at page 524160, version 0x01 [ 1.986708] Bad block table found at page 524032, version 0x01 [ 2.007163] fsl,ifc-nand 530000000.nand: IFC NAND device at 0x530000000, bank 2 [ 2.015151] spi-nor spi0.0: unrecognized JEDEC id bytes: 1e 3c 38 70 f1 e3 [ 2.022350] spi-nor spi1.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00 [ 2.029242] spi-nor: probe of spi1.0 failed with error -2 [ 2.035733] tun: Universal TUN/TAP device driver, 1.6 [ 2.041062] thunder_xcv, ver 1.0 [ 2.044302] thunder_bgx, ver 1.0 [ 2.047540] nicpf, ver 1.0 [ 2.050687] hclge is initializing [ 2.054011] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version [ 2.061232] hns3: Copyright (c) 2017 Huawei Corporation. [ 2.066558] e1000: Intel(R) PRO/1000 Network Driver [ 2.071432] e1000: Copyright (c) 1999-2006 Intel Corporation. [ 2.077188] e1000e: Intel(R) PRO/1000 Network Driver [ 2.082147] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.088140] e1000e 0000:01:00.0: Adding to iommu group 0 [ 2.093814] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.151199] e1000e 0000:01:00.0 0000:01:00.0 (uninitialized): registered PHC clock [ 2.168916] ata1: SATA link down (SStatus 0 SControl 300) [ 2.212687] e1000e 0000:01:00.0 eth0: (PCI Express:2.5GT/s:Width x1) 68:05:ca:3f:90:5c [ 2.220613] e1000e 0000:01:00.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.224914] ata2: SATA link down (SStatus 0 SControl 300) [ 2.227498] e1000e 0000:01:00.0 eth0: MAC: 3, PHY: 8, PBA No: E46981-008 [ 2.239598] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.244993] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.250576] igbvf: Intel(R) Gigabit Virtual Function Network Driver [ 2.256840] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 2.262912] sky2: driver version 1.30 [ 2.266968] VFIO - User Level meta-driver version: 0.3 [ 2.273323] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.279861] ehci-pci: EHCI PCI platform driver [ 2.284316] ehci-platform: EHCI generic platform driver [ 2.289583] ehci-orion: EHCI orion driver [ 2.293626] ehci-exynos: EHCI Exynos driver [ 2.297835] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.304017] ohci-pci: OHCI PCI platform driver [ 2.308468] ohci-platform: OHCI generic platform driver [ 2.313733] ohci-exynos: OHCI Exynos driver [ 2.318076] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.323566] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 2.331296] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.340708] xhci-hcd xhci-hcd.0.auto: irq 106, io mem 0x03100000 [ 2.346994] hub 1-0:1.0: USB hub found [ 2.350750] hub 1-0:1.0: 1 port detected [ 2.354774] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 2.360262] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 2.367919] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 2.374463] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.382720] hub 2-0:1.0: USB hub found [ 2.386474] hub 2-0:1.0: 1 port detected [ 2.390530] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.396018] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 2.403741] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002010010 [ 2.413149] xhci-hcd xhci-hcd.1.auto: irq 107, io mem 0x03110000 [ 2.419391] hub 3-0:1.0: USB hub found [ 2.423146] hub 3-0:1.0: 1 port detected [ 2.427156] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 2.432641] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 2.440298] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 2.446840] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.455096] hub 4-0:1.0: USB hub found [ 2.458856] hub 4-0:1.0: 1 port detected [ 2.462990] usbcore: registered new interface driver usb-storage [ 2.469963] i2c /dev entries driver [ 2.474633] i2c i2c-0: Added multiplexed i2c bus 1 [ 2.480557] rtc-ds3232 2-0068: oscillator discontinuity flagged, time unreliable [ 2.489510] hwmon hwmon0: temp1_input not attached to any thermal zone [ 2.501617] rtc-ds3232 2-0068: registered as rtc0 [ 2.507495] rtc-ds3232 2-0068: setting system clock to 2022-09-26T09:22:35 UTC (1664184155) [ 2.515907] i2c i2c-0: Added multiplexed i2c bus 2 [ 2.520832] i2c i2c-0: Added multiplexed i2c bus 3 [ 2.525750] i2c i2c-0: Added multiplexed i2c bus 4 [ 2.530609] i2c i2c-0: Added multiplexed i2c bus 5 [ 2.535464] i2c i2c-0: Added multiplexed i2c bus 6 [ 2.540319] i2c i2c-0: Added multiplexed i2c bus 7 [ 2.545176] i2c i2c-0: Added multiplexed i2c bus 8 [ 2.549967] pca954x 0-0075: registered 8 multiplexed busses for I2C mux pca9547 [ 2.558343] sp805-wdt c000000.wdt: registration successful [ 2.563906] sp805-wdt c010000.wdt: registration successful [ 2.569467] sp805-wdt c100000.wdt: registration successful [ 2.575024] sp805-wdt c110000.wdt: registration successful [ 2.580583] sp805-wdt c200000.wdt: registration successful [ 2.586135] sp805-wdt c210000.wdt: registration successful [ 2.591690] sp805-wdt c300000.wdt: registration successful [ 2.597242] sp805-wdt c310000.wdt: registration successful [ 2.604194] qoriq-cpufreq qoriq-cpufreq: Freescale QorIQ CPU frequency scaling driver [ 2.612653] sdhci: Secure Digital Host Controller Interface driver [ 2.618835] sdhci: Copyright(c) Pierre Ossman [ 2.623395] Synopsys Designware Multimedia Card Interface Driver [ 2.629765] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.636133] ledtrig-cpu: registered to indicate activity on CPUs [ 2.642713] usbcore: registered new interface driver usbhid [ 2.648286] usbhid: USB HID core driver [ 2.653297] optee: probing for conduit method. [ 2.657743] optee: api uid mismatch [ 2.658785] mmc0: SDHCI controller on 2140000.esdhc [2140000.esdhc] using ADMA 64-bit [ 2.661232] optee: probe of firmware:optee failed with error -22 [ 2.675678] NET: Registered protocol family 17 [ 2.680203] 9pnet: Installing 9P2000 support [ 2.684500] Key type dns_resolver registered [ 2.688966] printk: console [ttyS1]: printing thread started [ 2.688999] registered taskstats version 1 [ 2.689003] Loading compiled-in X.509 certificates [ 2.690571] pcieport 0000:00:00.0: Adding to iommu group 1 [ 2.690735] pcieport 0000:00:00.0: PME: Signaling with IRQ 112 [ 2.690878] pcieport 0001:00:00.0: Adding to iommu group 2 [ 2.691027] pcieport 0001:00:00.0: PME: Signaling with IRQ 116 [ 5.423756] e1000e 0000:01:00.0 eth0: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None [ 5.446775] Sending DHCP requests ..., OK [ 13.414793] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.190 [ 13.414802] IP-Config: Complete: [ 13.414804] device=eth0, hwaddr=68:05:ca:3f:90:5c, ipaddr=172.16.1.190, mask=255.255.255.0, gw=172.16.1.4 [ 13.414812] host=172.16.1.190, domain=example.org, nis-domain=(none) [ 13.414816] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= [ 13.414821] nameserver0=172.16.1.4 [ 13.415023] ALSA device list: [ 13.415029] No soundcards found. [ 13.417516] Freeing unused kernel memory: 5952K [ 13.486853] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 13.523933] udevd[185]: starting version 3.2.9 [ 13.524235] random: udevd: uninitialized urandom read (16 bytes read) [ 13.524307] random: udevd: uninitialized urandom read (16 bytes read) [ 13.524333] random: udevd: uninitialized urandom read (16 bytes read) [ 13.526336] udevd[185]: specified user 'tss' unknown [ 13.526369] udevd[185]: specified group 'tss' unknown [ 13.527316] udevd[186]: starting eudev-3.2.9 [ 13.635991] lm90 4-004c: supply vcc not found, using dummy regulator [ 13.638325] ina2xx 3-0040: error configuring the device: -6 [ 13.642071] udevd[206]: Error changing net interface name eth0 to enp1s0: Device or resource busy [ 13.642094] udevd[206]: could not rename interface '2' from 'eth0' to 'enp1s0': Device or resource busy [ 13.652916] hwmon hwmon7: temp1_input not attached to any thermal zone [ 13.652930] hwmon hwmon7: temp2_input not attached to any thermal zone done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK [ 13.720443] NET: Registered protocol family 10 [ 13.721254] Segment Routing with IPv6 /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1147066/environment . /lava-1147066/environment / # /lava-1147066/bin/lava-test-runner /lava-1147066/0 /lava-1147066/bin/lava-test-runner /lava-1147066/0 + export 'TESTRUN_ID=0_dmesg' + c[ 14.233969] d /lava-1147066/0/tests/0_dmesg + cat uuid + UUID=1147066_1.5.2.4.1 + set +x[ 14.243303] + KERNELCI_LAVA[ 14.251910] =y /bin/sh /opt/[ 14.260167] kernelci/dmesg.sh + set +x XIT> / #