Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. U-Boot SPL 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500) Trying to boot from MMC2 Loading Environment from EXT4... Card did not respond to voltage select! U-Boot 2019.04-00002-gf15b99f0b6 (Oct 01 2019 - 09:28:05 -0500), Build: jenkins-github_Bootloader-Builder-131 CPU : AM335X-GP rev 2.1 I2C: ready DRAM: 512 MiB No match for driver 'omap_hsmmc' No match for driver 'omap_hsmmc' Some drivers were not found Reset Source: Power-on reset has occurred. RTC 32KCLK Source: External. MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from EXT4... Card did not respond to voltage select! Board: BeagleBone Black not set. Validating first E-fuse MAC BeagleBone Black: BeagleBone: cape eeprom: i2c_probe: 0x54: BeagleBone: cape eeprom: i2c_probe: 0x55: BeagleBone: cape eeprom: i2c_probe: 0x56: BeagleBone: cape eeprom: i2c_probe: 0x57: Net: eth0: MII MODE cpsw, usb_ether Press SPACE to abort autoboot in 2 seconds => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp link up on port 0, speed 100, full duplex BOOTP broadcast 1 DHCP client bound to address 192.168.11.2 (4 ms) => setenv serverip 192.168.11.5 setenv serverip 192.168.11.5 => tftp 0x82000000 855828/tftp-deploy-x5yuksj8/kernel/zImage tftp 0x82000000 855828/tftp-deploy-x5yuksj8/kernel/zImage link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '855828/tftp-deploy-x5yuksj8/kernel/zImage'. Load address: 0x82000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## 5.2 MiB/s done Bytes transferred = 9687552 (93d200 hex) => tftp 0x83000000 855828/tftp-deploy-x5yuksj8/ramdisk/ramdisk.cpio.gz.uboot tftp 0x83000000 855828/tftp-deploy-x5yuksj8/ramdisk/ramdisk.cpio.gz.uboot link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '855828/tftp-deploy-x5yuksj8/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 5.1 MiB/s done Bytes transferred = 12142825 (b948e9 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x88000000 855828/tftp-deploy-x5yuksj8/dtb/am335x-boneblack.dtb tftp 0x88000000 855828/tftp-deploy-x5yuksj8/dtb/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 192.168.11.5; our IP address is 192.168.11.2 Filename '855828/tftp-deploy-x5yuksj8/dtb/am335x-boneblack.dtb'. Load address: 0x88000000 Loading: *##### 4.6 MiB/s done Bytes transferred = 62828 (f56c hex) => setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/855828/extract-nfsrootfs-mdtah2m5,tcp,hard console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/855828/extract-nfsrootfs-mdtah2m5,tcp,hard console_msg_format=syslog earlycon ip=dhcp' => bootz 0x82000000 0x83000000 0x88000000 bootz 0x82000000 0x83000000 0x88000000 ## Loading init Ramdisk from Legacy Image at 83000000 ... Image Name: Created: 2023-02-21 17:43:35 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12142761 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Using Device Tree in place at 88000000, end 8801256b Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.167-cip26 (KernelCI@build-j1077747-arm-gcc-10-multi-v7-defconfig-rms94) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Feb 21 12:53:12 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: TI AM335x BeagleBone Black [ 0.000000] earlycon: omap8250 at MMIO 0x44e09000 (options '') [ 0.000000] printk: bootconsole [omap8250] enabled [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9b800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fdfffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] AM335X ES2.1 (sgx neon) [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129540 [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/nfs rw nfsroot=192.168.11.5:/var/lib/lava/dispatcher/tmp/855828/extract-nfsrootfs-mdtah2m5,tcp,hard console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 415716K/522240K available (13312K kernel code, 2233K rwdata, 5348K rodata, 2048K init, 426K bss, 40988K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] IRQ: Found an INTC at 0x(ptrval) (revision 5.0) with 128 interrupts <6>[ 0.000000] TI gptimer clocksource: always-on /ocp/interconnect@44c00000/segment@200000/target-module@31000 <6>[ 0.000010] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008337] clocksource: dmtimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.019062] TI gptimer clockevent: 24000000 Hz at /ocp/interconnect@48000000/segment@0/target-module@40000 <6>[ 0.033090] Console: colour dummy device 80x30 <3>[ 0.037955] WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0' <3>[ 0.045002] This ensures that you still see kernel messages. Please <3>[ 0.051723] update your kernel commandline. <6>[ 0.056326] Calibrating delay loop... 996.14 BogoMIPS (lpj=4980736) <6>[ 0.096026] pid_max: default: 32768 minimum: 301 <6>[ 0.101231] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.109022] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.118013] CPU: Testing write buffer coherency: ok <6>[ 0.123407] CPU0: Spectre v2: using BPIALL workaround <6>[ 0.129191] CPU0: thread -1, cpu 0, socket -1, mpidr 0 <6>[ 0.135487] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.144642] rcu: Hierarchical SRCU implementation. <6>[ 0.154468] EFI services will not be available. <6>[ 0.159633] smp: Bringing up secondary CPUs ... <6>[ 0.164562] smp: Brought up 1 node, 1 CPU <6>[ 0.168948] SMP: Total of 1 processors activated (996.14 BogoMIPS). <6>[ 0.175681] CPU: All CPU(s) started in SVC mode. <6>[ 0.181282] devtmpfs: initialized <6>[ 0.195533] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 <6>[ 0.204058] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.214487] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.225618] pinctrl core: initialized pinctrl subsystem <6>[ 0.233862] DMI not present or invalid. <6>[ 0.238845] NET: Registered protocol family 16 <6>[ 0.246242] DMA: preallocated 256 KiB pool for atomic coherent allocations <3>[ 0.272797] l3-aon-clkctrl:0000:0: failed to disable <6>[ 0.280928] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.281131] cpuidle: using governor menu <6>[ 1.361827] No ATAGs? <6>[ 1.364452] hw-breakpoint: debug architecture 0x4 unsupported. <6>[ 1.378802] Serial: AMBA PL011 UART driver <6>[ 1.417019] iommu: Default domain type: Translated <6>[ 1.422873] vgaarb: loaded <5>[ 1.426860] SCSI subsystem initialized <6>[ 1.431958] usbcore: registered new interface driver usbfs <6>[ 1.437915] usbcore: registered new interface driver hub <6>[ 1.443768] usbcore: registered new device driver usb <6>[ 1.451041] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.456421] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.466143] PTP clock support registered <6>[ 1.474171] clocksource: Switched to clocksource dmtimer <6>[ 2.434661] NET: Registered protocol family 2 <6>[ 2.439704] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 2.448200] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 2.457128] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 2.465409] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 2.473064] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 2.479996] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.487017] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 2.494610] NET: Registered protocol family 1 <6>[ 2.500186] RPC: Registered named UNIX socket transport module. <6>[ 2.506629] RPC: Registered udp transport module. <6>[ 2.511732] RPC: Registered tcp transport module. <6>[ 2.516851] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 2.523748] PCI: CLS 0 bytes, default 64 <6>[ 2.528757] Trying to unpack rootfs image as initramfs... <6>[ 3.297200] Freeing initrd memory: 11860K <6>[ 3.302574] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available <5>[ 3.312908] Initialise system trusted keyrings <6>[ 3.318286] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 3.331293] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 3.338636] NFS: Registering the id_resolver key type <5>[ 3.344227] Key type id_resolver registered <5>[ 3.348797] Key type id_legacy registered <6>[ 3.353303] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 3.360494] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 3.368417] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 3.373732] Key type asymmetric registered <5>[ 3.378269] Asymmetric key parser 'x509' registered <6>[ 3.383602] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 3.391493] io scheduler mq-deadline registered <6>[ 3.396433] io scheduler kyber registered <3>[ 3.552676] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.561384] omap_gpio 44e07000.gpio: Could not register gpio chip -517 <4>[ 3.682856] ti-sysc: probe of 44e31000.target-module failed with error -16 <4>[ 3.728752] ti-sysc: probe of 48040000.target-module failed with error -16 <3>[ 3.808101] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.816797] omap_gpio 4804c000.gpio: Could not register gpio chip -517 <3>[ 3.882922] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.891626] omap_gpio 481ac000.gpio: Could not register gpio chip -517 <3>[ 3.910376] gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517 <3>[ 3.919062] omap_gpio 481ae000.gpio: Could not register gpio chip -517 <3>[ 3.988676] debugfs: Directory '49000000.dma' with parent 'dmaengine' already present! <6>[ 3.997231] edma 49000000.dma: TI EDMA DMA engine driver <6>[ 4.038967] pinctrl-single 44e10800.pinmux: 142 pins, size 568 <6>[ 4.140418] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 4.152726] 44e09000.serial: ttyS0 at MMIO 0x44e09000 (irq = 20, base_baud = 3000000) is a 8250 <6>[ 4.162156] printk: console [ttyS0] enabled <6>[ 4.162156] printk: console [ttyS0] enabled <6>[ 4.171208] printk: bootconsole [omap8250] disabled <6>[ 4.171208] printk: bootconsole [omap8250] disabled <6>[ 4.185131] SuperH (H)SCI(F) driver initialized <6>[ 4.191934] msm_serial: driver initialized <6>[ 4.196843] STMicroelectronics ASC driver initialized <6>[ 4.205054] STM32 USART driver initialized <6>[ 4.212316] omap_rng 48310000.rng: Random Number Generator ver. 20 <5>[ 4.232512] random: crng init done <6>[ 4.245892] brd: module loaded <6>[ 4.257035] loop: module loaded <6>[ 4.281728] CAN device driver interface <6>[ 4.287900] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 4.296144] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 4.301402] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 4.307781] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 4.313468] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 4.384256] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6, bus freq 1000000 <6>[ 4.408164] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 <6>[ 4.418079] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 <6>[ 4.424784] cpsw 4a100000.ethernet: ALE Table size 1024 <6>[ 4.430558] cpsw 4a100000.ethernet: Detected MACID = 64:cf:d9:3f:a0:d5 <6>[ 4.439696] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 4.447607] usbcore: registered new interface driver pegasus <6>[ 4.453603] usbcore: registered new interface driver asix <6>[ 4.459360] usbcore: registered new interface driver ax88179_178a <6>[ 4.465797] usbcore: registered new interface driver cdc_ether <6>[ 4.471972] usbcore: registered new interface driver smsc75xx <6>[ 4.478068] usbcore: registered new interface driver smsc95xx <6>[ 4.484151] usbcore: registered new interface driver net1080 <6>[ 4.490123] usbcore: registered new interface driver cdc_subset <6>[ 4.496375] usbcore: registered new interface driver zaurus <6>[ 4.502282] usbcore: registered new interface driver cdc_ncm <6>[ 4.513513] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 4.520445] ehci-pci: EHCI PCI platform driver <6>[ 4.525249] ehci-platform: EHCI generic platform driver <6>[ 4.531241] ehci-orion: EHCI orion driver <6>[ 4.535945] SPEAr-ehci: EHCI SPEAr driver <6>[ 4.540533] ehci-st: EHCI STMicroelectronics driver <6>[ 4.546077] ehci-exynos: EHCI Exynos driver <6>[ 4.550847] ehci-atmel: EHCI Atmel driver <6>[ 4.555493] tegra-ehci: Tegra EHCI driver <6>[ 4.560117] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 4.566683] ohci-pci: OHCI PCI platform driver <6>[ 4.571489] ohci-platform: OHCI generic platform driver <6>[ 4.577480] SPEAr-ohci: OHCI SPEAr driver <6>[ 4.582080] ohci-st: OHCI STMicroelectronics driver <6>[ 4.587612] ohci-atmel: OHCI Atmel driver <6>[ 4.593512] usbcore: registered new interface driver usb-storage <6>[ 4.610313] i2c /dev entries driver <5>[ 4.641654] cpuidle: enable-method property 'ti,am3352' found operations <6>[ 4.650025] sdhci: Secure Digital Host Controller Interface driver <6>[ 4.656603] sdhci: Copyright(c) Pierre Ossman <6>[ 4.665560] Synopsys Designware Multimedia Card Interface Driver <6>[ 4.674890] sdhci-pltfm: SDHCI platform and OF driver helper <4>[ 4.689520] sdhci-omap 481d8000.mmc: supply vqmmc not found, using dummy regulator <6>[ 4.749443] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 4.758914] usbcore: registered new interface driver usbhid <6>[ 4.764919] usbhid: USB HID core driver <6>[ 4.778363] NET: Registered protocol family 10 <6>[ 4.784631] Segment Routing with IPv6 <6>[ 4.788659] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 4.795632] NET: Registered protocol family 17 <6>[ 4.800379] can: controller area network core <6>[ 4.805173] NET: Registered protocol family 29 <6>[ 4.809901] can: raw protocol <6>[ 4.813145] can: broadcast manager protocol <6>[ 4.817642] can: netlink gateway - max_hops=1 <5>[ 4.823048] Key type dns_resolver registered <6>[ 4.827826] ThumbEE CPU extension supported. <5>[ 4.832392] Registering SWP/SWPB emulation handler <3>[ 4.837906] omap_voltage_late_init: Voltage driver support not added <6>[ 4.846115] mmc1: SDHCI controller on 481d8000.mmc [481d8000.mmc] using External DMA <5>[ 4.854986] Loading compiled-in X.509 certificates <6>[ 4.876577] OMAP GPIO hardware version 0.1 <4>[ 4.914766] tps65217-pmic: Failed to locate of_node [id: -1] <4>[ 4.928070] tps65217-bl: Failed to locate of_node [id: -1] <6>[ 4.943269] tps65217 0-0024: TPS65217 ID 0xe version 1.2 <4>[ 4.949649] at24 0-0050: supply vcc not found, using dummy regulator <6>[ 4.957033] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write <6>[ 4.965006] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz <4>[ 4.974979] at24 2-0054: supply vcc not found, using dummy regulator <6>[ 4.984579] mmc1: new high speed MMC card at address 0001 <6>[ 4.991115] mmcblk1: mmc1:0001 M62704 3.56 GiB <6>[ 4.996364] mmcblk1boot0: mmc1:0001 M62704 partition 1 2.00 MiB <6>[ 5.002884] mmcblk1boot1: mmc1:0001 M62704 partition 2 2.00 MiB <6>[ 5.009512] mmcblk1rpmb: mmc1:0001 M62704 partition 3 512 KiB, chardev (235:0) <6>[ 5.018997] mmcblk1: p1 <4>[ 5.023137] at24 2-0055: supply vcc not found, using dummy regulator <4>[ 5.057837] at24 2-0056: supply vcc not found, using dummy regulator <4>[ 5.097247] at24 2-0057: supply vcc not found, using dummy regulator <6>[ 5.137690] omap_i2c 4819c000.i2c: bus 2 rev0.11 at 100 kHz <6>[ 5.161301] omap_gpio 44e07000.gpio: Could not set line 6 debounce to 200000 microseconds (-22) <6>[ 5.170487] sdhci-omap 48060000.mmc: Got CD GPIO <4>[ 5.175618] sdhci-omap 48060000.mmc: supply vqmmc not found, using dummy regulator <6>[ 5.263565] mmc0: SDHCI controller on 48060000.mmc [48060000.mmc] using External DMA <6>[ 5.275520] cpsw 4a100000.ethernet: initializing cpsw version 1.12 (0) <6>[ 5.366030] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=POLL) <6>[ 8.515108] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 8.534318] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 8.564325] Sending DHCP requests ., OK <6>[ 8.608428] IP-Config: Got DHCP answer from 192.168.11.1, my address is 192.168.11.2 <6>[ 8.616590] IP-Config: Complete: <6>[ 8.620132] device=eth0, hwaddr=64:cf:d9:3f:a0:d5, ipaddr=192.168.11.2, mask=255.255.255.0, gw=192.168.11.1 <6>[ 8.630721] host=192.168.11.2, domain=usen.ad.jp, nis-domain=(none) <6>[ 8.637802] bootserver=0.0.0.0, rootserver=192.168.11.5, rootpath= <6>[ 8.637821] nameserver0=192.168.11.1 <6>[ 8.662160] Freeing unused kernel memory: 2048K <6>[ 8.685080] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 <4>[ 11.655553] am335x-phy-driver 47401300.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.664620] am335x-phy-driver 47401300.usb-phy: dummy supplies not allowed for exclusive requests <4>[ 11.745569] am335x-phy-driver 47401b00.usb-phy: supply vcc not found, using dummy regulator <4>[ 11.754659] am335x-phy-driver 47401b00.usb-phy: dummy supplies not allowed for exclusive requests <6>[ 11.990011] musb-hdrc musb-hdrc.1: MUSB HDRC host driver <6>[ 11.995780] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 12.131348] hub 1-0:1.0: USB hub found <6>[ 12.178266] hub 1-0:1.0: 1 port detected Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/nfs-top ... done. Begin: Running /scripts/nfs-premount ... Waiting up to 60 secs for any ethernet to become available Device /sys/class/net/eth0 found done. IP-Config: eth0 hardware address 64:cf:d9:3f:a0:d5 mtu 1500 DHCP IP-Config: eth0 guessed broadcast address 192.168.11.255 IP-Config: eth0 complete (dhcp from 192.168.11.1): address: 192.168.11.2 broadcast: 192.168.11.255 netmask: 255.255.255.0 gateway: 192.168.11.1 dns0 : 192.168.11.1 dns1 : 0.0.0.0 domain : usen.ad.jp rootserver: 192.168.11.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. <30>[ 15.263191] systemd[1]: System time before build time, advancing clock. <30>[ 15.362307] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) <30>[ 15.387077] systemd[1]: Detected architecture arm. Welcome to [1mDebian GNU/Linux 11 (bullseye)[0m! <30>[ 15.437419] systemd[1]: Set hostname to . <30>[ 17.094503] systemd[1]: Queued start job for default target Graphical Interface. <28>[ 17.106745] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. <28>[ 17.119740] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) <30>[ 17.130092] systemd[1]: Created slice system-getty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-getty.slice[0m. <30>[ 17.165920] systemd[1]: Created slice system-modprobe.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-modprobe.slice[0m. <30>[ 17.207212] systemd[1]: Created slice system-serial\x2dgetty.slice. [[0;32m OK [0m] Created slice [0;1;39msystem-serial\x2dgetty.slice[0m. <30>[ 17.246607] systemd[1]: Created slice User and Session Slice. [[0;32m OK [0m] Created slice [0;1;39mUser and Session Slice[0m. <30>[ 17.285396] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [[0;32m OK [0m] Started [0;1;39mDispatch Password …ts to Console Directory Watch[0m. <30>[ 17.325931] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [[0;32m OK [0m] Started [0;1;39mForward Password R…uests to Wall Directory Watch[0m. <30>[ 17.365748] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. <30>[ 17.379083] systemd[1]: Reached target Local Encrypted Volumes. [[0;32m OK [0m] Reached target [0;1;39mLocal Encrypted Volumes[0m. <30>[ 17.415131] systemd[1]: Reached target Paths. [[0;32m OK [0m] Reached target [0;1;39mPaths[0m. <30>[ 17.455151] systemd[1]: Reached target Remote File Systems. [[0;32m OK [0m] Reached target [0;1;39mRemote File Systems[0m. <30>[ 17.495028] systemd[1]: Reached target Slices. [[0;32m OK [0m] Reached target [0;1;39mSlices[0m. <30>[ 17.534816] systemd[1]: Reached target Swap. [[0;32m OK [0m] Reached target [0;1;39mSwap[0m. <30>[ 17.577074] systemd[1]: Listening on initctl Compatibility Named Pipe. [[0;32m OK [0m] Listening on [0;1;39minitctl Compatibility Named Pipe[0m. <30>[ 17.666839] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. <30>[ 17.678223] systemd[1]: Listening on Journal Socket (/dev/log). [[0;32m OK [0m] Listening on [0;1;39mJournal Socket (/dev/log)[0m. <30>[ 17.715916] systemd[1]: Listening on Journal Socket. [[0;32m OK [0m] Listening on [0;1;39mJournal Socket[0m. <30>[ 17.759478] systemd[1]: Listening on Network Service Netlink Socket. [[0;32m OK [0m] Listening on [0;1;39mNetwork Service Netlink Socket[0m. <30>[ 17.813359] systemd[1]: Listening on udev Control Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Control Socket[0m. <30>[ 17.855872] systemd[1]: Listening on udev Kernel Socket. [[0;32m OK [0m] Listening on [0;1;39mudev Kernel Socket[0m. <30>[ 17.896993] systemd[1]: Condition check resulted in Huge Pages File System being skipped. <30>[ 17.909510] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. <30>[ 17.923838] systemd[1]: Mounting Kernel Debug File System... Mounting [0;1;39mKernel Debug File System[0m... <30>[ 17.969251] systemd[1]: Mounting Kernel Trace File System... Mounting [0;1;39mKernel Trace File System[0m... <30>[ 18.075585] systemd[1]: Starting Create list of static device nodes for the current kernel... Starting [0;1;39mCreate list of st…odes for the current kernel[0m... <30>[ 18.138878] systemd[1]: Starting Load Kernel Module configfs... Starting [0;1;39mLoad Kernel Module configfs[0m... <30>[ 18.188966] systemd[1]: Starting Load Kernel Module drm... Starting [0;1;39mLoad Kernel Module drm[0m... <30>[ 18.226112] systemd[1]: Starting Load Kernel Module fuse... Starting [0;1;39mLoad Kernel Module fuse[0m... <30>[ 18.257289] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. <30>[ 18.291725] systemd[1]: Starting Journal Service... Starting [0;1;39mJournal Service[0m... <30>[ 18.356126] systemd[1]: Starting Load Kernel Modules... Starting [0;1;39mLoad Kernel Modules[0m... <30>[ 18.398579] systemd[1]: Starting Remount Root and Kernel File Systems... Starting [0;1;39mRemount Root and Kernel File Systems[0m... <30>[ 18.468860] systemd[1]: Starting Coldplug All udev Devices... Starting [0;1;39mColdplug All udev Devices[0m... <30>[ 18.550761] systemd[1]: Mounted Kernel Debug File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Debug File System[0m. <30>[ 18.641172] systemd[1]: Mounted Kernel Trace File System. [[0;32m OK [0m] Mounted [0;1;39mKernel Trace File System[0m. <30>[ 18.706660] systemd[1]: Finished Create list of static device nodes for the current kernel. [[0;32m OK [0m] Finished [0;1;39mCreate list of st… nodes for the current kernel[0m. <30>[ 18.851397] systemd[1]: modprobe@configfs.service: Succeeded. <30>[ 18.884778] systemd[1]: Finished Load Kernel Module configfs. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module configfs[0m. <30>[ 18.926585] systemd[1]: modprobe@drm.service: Succeeded. <30>[ 18.954619] systemd[1]: Finished Load Kernel Module drm. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module drm[0m. <30>[ 18.996661] systemd[1]: modprobe@fuse.service: Succeeded. <30>[ 19.014649] systemd[1]: Finished Load Kernel Module fuse. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Module fuse[0m. <30>[ 19.046852] systemd[1]: Finished Load Kernel Modules. [[0;32m OK [0m] Finished [0;1;39mLoad Kernel Modules[0m. <30>[ 19.086810] systemd[1]: Finished Remount Root and Kernel File Systems. [[0;32m OK [0m] Finished [0;1;39mRemount Root and Kernel File Systems[0m. <30>[ 19.145664] systemd[1]: Started Journal Service. [[0;32m OK [0m] Started [0;1;39mJournal Service[0m. Mounting [0;1;39mKernel Configuration File System[0m... Starting [0;1;39mFlush Journal to Persistent Storage[0m... Starting [0;1;39mLoad/Save Random Seed[0m... Starting [0;1;39mApply Kernel Variables[0m... Starting [0;1;39mCreate System Users[0m... [[0;32m OK [0m] Mounted [0;1;39mKernel Configuration File System[0m. <46>[ 19.648522] systemd-journald[146]: Received client request to flush runtime journal. [[0;32m OK [0m] Finished [0;1;39mLoad/Save Random Seed[0m. [[0;32m OK [0m] Finished [0;1;39mApply Kernel Variables[0m. [[0;32m OK [0m] Finished [0;1;39mCreate System Users[0m. Starting [0;1;39mCreate Static Device Nodes in /dev[0m... [[0;32m OK [0m] Finished [0;1;39mFlush Journal to Persistent Storage[0m. [[0;32m OK [0m] Finished [0;1;39mCreate Static Device Nodes in /dev[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems (Pre)[0m. [[0;32m OK [0m] Reached target [0;1;39mLocal File Systems[0m. Starting [0;1;39mCreate Volatile Files and Directories[0m... Starting [0;1;39mRule-based Manage…for Device Events and Files[0m... [[0;32m OK [0m] Started [0;1;39mRule-based Manager for Device Events and Files[0m. Starting [0;1;39mNetwork Service[0m... [[0;32m OK [0m] Finished [0;1;39mCreate Volatile Files and Directories[0m. Starting [0;1;39mNetwork Time Synchronization[0m... Starting [0;1;39mUpdate UTMP about System Boot/Shutdown[0m... [[0;32m OK [0m] Finished [0;1;39mColdplug All udev Devices[0m. [[0;32m OK [0m] Finished [0;1;39mUpdate UTMP about System Boot/Shutdown[0m. [[0;32m OK [0m] Started [0;1;39mNetwork Service[0m. Starting [0;1;39mNetwork Name Resolution[0m... [[0;32m OK [0m] Started [0;1;39mNetwork Time Synchronization[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Initialization[0m. [[0;32m OK [0m] Started [0;1;39mDaily Cleanup of Temporary Directories[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Set[0m. [[0;32m OK [0m] Reached target [0;1;39mSystem Time Synchronized[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt download activities[0m. [[0;32m OK [0m] Started [0;1;39mDaily apt upgrade and clean activities[0m. [[0;32m OK [0m] Started [0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[0m. [[0;32m OK [0m] Started [0;1;39mDiscard unused blocks once a week[0m. [[0;32m OK [0m] Reached target [0;1;39mTimers[0m. [[0;32m OK [0m] Listening on [0;1;39mD-Bus System Message Bus Socket[0m. [[0;32m OK [0m] Reached target [0;1;39mSockets[0m. [[0;32m OK [0m] Reached target [0;1;39mBasic System[0m. [[0;32m OK [0m] Started [0;1;39mD-Bus System Message Bus[0m. Starting [0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[0m... Starting [0;1;39mUser Login Management[0m... [[0m[0;31m* [0m] (1 of 4) A start job is running for…a Check Snapshots (11s / no limit) M[K[[0;1;31m*[0m[0;31m* [0m] (1 of 4) A start job is running for…a Check Snapshots (11s / no limit) M[K[[0;31m*[0;1;31m*[0m[0;31m* [0m] (1 of 4) A start job is running for…a Check Snapshots (12s / no limit) M[K[[0;32m OK [0m] Started [0;1;39mNetwork Name Resolution[0m. [K[[0;32m OK [0m] Reached target [0;1;39mNetwork[0m. [[0;32m OK [0m] Reached target [0;1;39mHost and Network Name Lookups[0m. Starting [0;1;39mPermit User Sessions[0m... [[0;32m OK [0m] Finished [0;1;39mPermit User Sessions[0m. [[0;32m OK [0m] Started [0;1;39mGetty on tty1[0m. [[0;32m OK [0m] Found device [0;1;39m/dev/ttyS0[0m. [ [0;31m*[0;1;31m*[0m[0;31m* [0m] (2 of 2) A start job is running for… Login Management (16s / 1min 38s) M[K[ [0;31m*[0;1;31m*[0m[0;31m* [0m] (2 of 2) A start job is running for… Login Management (17s / 1min 38s) M[K[ [0;31m*[0;1;31m*[0m[0;31m*[0m] (2 of 2) A start job is running for… Login Management (17s / 1min 38s) M[K[ [0;31m*[0;1;31m*[0m] (1 of 2) A start job is running for…a Check Snapshots (18s / no limit) M[K[ [0;31m*[0m] (1 of 2) A start job is running for…a Check Snapshots (18s / no limit) M[K[ [0;31m*[0;1;31m*[0m] (1 of 2) A start job is running for…a Check Snapshots (18s / no limit) M[K[[0;32m OK [0m] Finished [0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[0m. [K[[0;32m OK [0m] Started [0;1;39mUser Login Management[0m. [[0;32m OK [0m] Reached target [0;1;39mHardware activated USB gadget[0m. [[0;32m OK [0m] Listening on [0;1;39mLoad/Save RF …itch Status /dev/rfkill Watch[0m. [[0;32m OK [0m] Started [0;1;39mSerial Getty on ttyS0[0m. [[0;32m OK [0m] Reached target [0;1;39mLogin Prompts[0m. [[0;32m OK [0m] Reached target [0;1;39mMulti-User System[0m. [[0;32m OK [0m] Reached target [0;1;39mGraphical Interface[0m. Starting [0;1;39mUpdate UTMP about System Runlevel Changes[0m... Debian GNU/Linux 11seye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.167-cip26 #1 SMP Tue Feb 21 12:53:12 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/855828/extract-nfsrootfs-mdtah2m5' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/855828/extract-nfsrootfs-mdtah2m5' / # export NFS_SERVER_IP='192.168.11.5' export NFS_SERVER_IP='192.168.11.5' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-855828/environment . /lava-855828/environment / # /lava-855828/bin/lava-test-runner /lava-855828/0 /lava-855828/bin/lava-test-runner /lava-855828/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-855828/0/tests/0_timesync-off ++ cat uuid + UUID=855828_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-capabilities + TESTRUN_ID=1_kselftest-capabilities + cd /lava-855828/0/tests/1_kselftest-capabilities ++ cat uuid + UUID=855828_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c capabilities -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.167-cip26-2-g28bb49f7179b/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S skipfile-lkft.yaml -b beaglebone-black -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-855828/0/tests/1_kselftest-capabilities/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: install_deps skipped --2023-02-21 17:45:12-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.167-cip26-2-g28bb49f7179b/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1407632 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 7%[> ] 105.20K 363KB/s kselftest.tar.xz 30%[=====> ] 414.57K 708KB/s kselftest.tar.xz 96%[==================> ] 1.29M 1.64MB/s kselftest.tar.xz 100%[===================>] 1.34M 1.70MB/s in 0.8s 2023-02-21 17:45:13 (1.70 MB/s) - 'kselftest.tar.xz' saved [1407632/1407632] skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test ftrace:ftracetest net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== capabilities:test_execve ============== Tests to run =============== capabilities:test_execve ===========End Tests to run =============== <12>[ 63.050361] kselftest: Running tests in capabilities TAP version 13 1..1 # selftests: capabilities: test_execve # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # TAP version 13 # 1..12 # # [RUN] +++ Tests with uid == 0 +++ # # [NOTE] Using global UIDs for tests # # [RUN] Root => ep # ok 1 Passed # # Check cap_ambient manipulation rules # ok 2 PR_CAP_AMBIENT_RAISE failed on non-inheritable cap # ok 3 PR_CAP_AMBIENT_RAISE failed on non-permitted cap # ok 4 PR_CAP_AMBIENT_RAISE worked # ok 5 Basic manipulation appears to work # # [RUN] Root +i => eip # ok 6 Passed # # [RUN] UID 0 +ia => eipa # ok 7 Passed # # [RUN] Root +ia, suidroot => eipa # ok 8 Passed # # [RUN] Root +ia, suidnonroot => ip # ok 9 Passed # # [RUN] Root +ia, sgidroot => eipa # ok 10 Passed # ok 11 Passed # # [RUN] Root +ia, sgidnonroot => eip # ok 12 Passed # # Totals: pass:12 fail:0 xfail:0 xpass:0 skip:0 error:0 # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # validate_cap:: Capabilities after execve were correct # # ================================================== # TAP version 13 # 1..9 # # [RUN] +++ Tests with uid != 0 +++ # # [NOTE] Using global UIDs for tests # # [RUN] Non-root => no caps # ok 1 Passed # # Check cap_ambient manipulation rules # ok 2 PR_CAP_AMBIENT_RAISE failed on non-inheritable cap # ok 3 PR_CAP_AMBIENT_RAISE failed on non-permitted cap # ok 4 PR_CAP_AMBIENT_RAISE worked # ok 5 Basic manipulation appears to work # # [RUN] Non-root +i => i # ok 6 Passed # # [RUN] UID 1 +ia => eipa # ok 7 Passed # # [RUN] Non-root +ia, sgidnonroot => i # ok 8 Passed # ok 9 Passed # # Totals: pass:9 fail:0 xfail:0 xpass:0 skip:0 error:0 # # ================================================== ok 1 selftests: capabilities: test_execve capabilities_test_execve_Passed pass capabilities_test_execve_PR_CAP_AMBIENT_RAISE_failed_on_non-inheritable_cap pass capabilities_test_execve_PR_CAP_AMBIENT_RAISE_failed_on_non-permitted_cap pass capabilities_test_execve_PR_CAP_AMBIENT_RAISE_worked pass capabilities_test_execve_Basic_manipulation_appears_to_work pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_PR_CAP_AMBIENT_RAISE_failed_on_non-inheritable_cap pass capabilities_test_execve_PR_CAP_AMBIENT_RAISE_failed_on_non-permitted_cap pass capabilities_test_execve_PR_CAP_AMBIENT_RAISE_worked pass capabilities_test_execve_Basic_manipulation_appears_to_work pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve_Passed pass capabilities_test_execve pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #