connecting to NetworkSerialPort(target=Target(name='imx53-qsrb-0', env=None), name='NetworkSerialPort', state=, avail=True, host='moxa.cuskci.stw.pengutronix.de', port=4010, speed=115200, protocol='rfc2217') calling microcom -s 115200 -t moxa.cuskci.stw.pengutronix.de:4010 connected to 10.8.254.5 (port 4010) Escape character: Ctrl-\ Type the escape character to get to the prompt. barebox 2023.01.0 #1 Fri Jan 27 16:21:21 CET 2023 Board: Freescale i.MX53 Quick Start-R Board detected i.MX53 revision 2.1 mc13xxx-i2c mc347080: Found MC34708 ID: 0x014 mdio_bus: miibus0: probed eth0: got preset MAC address: 00:04:9f:02:71:b3 imx-usb 53f80200.usb@53f80200.of: USB EHCI 1.00 imx-esdhc 50004000.mmc@50004000.of: registered as mmc0 imx-esdhc 50020000.mmc@50020000.of: registered as mmc2 imx-ipuv3 18000000.ipu@18000000.of: IPUv3M probed netconsole: registered as netconsole-1 malloc space: 0xbfe7d3c0 -> 0xcfcfa77f (size 254.5 MiB) mmc0: detected SD card version 2.0 mmc0: registered mmc0 MCIMX53-START-R board 1.0 rev B envfs: no envfs (magic mismatch) - envfs never written? [?25h Hit m for menu or any to stop autoboot: 3 [1;32mbarebox@[1;36mFreescale i.MX53 Quick Start-R Board:/[0m bootm -v -r /mnt/tftp/910206/tftp-deploy-qes8fiy1/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/910206/tftp-deploy-qes8fiy1/dtb/imx53-qsrb.dtb /mnt/tftp/910206/tftp-deploy-qes8fiy1/kernel/zImage [1;32mbarebox@[1;36mFreescale i.MX53 Quick Start-R Board:/[0m bootm -v -r /mnt/tftp/910206/tftp-deploy-qes8fiy1/ramdisk/ramdisk.cpio.gz -o /mnt/tftp/910206/tftp-deploy-qes8fiy1/dtb/imx53-qsrb.dtb /mnt/tftp/910206/tftp-deploy-qes8fiy1/kernel/zImage eth0: 100Mbps full duplex link detected T eth0: DHCP client bound to address 10.8.254.89 Loading ARM Linux zImage '/mnt/tftp/910206/tftp-deploy-qes8fiy1/kernel/zImage' OS image not yet relocated Passing control to ARM zImage handler no OS load address, defaulting to 0x72e32000 no initrd load address, defaulting to 0x78000000 Loaded initrd GZIP compressed '/mnt/tftp/910206/tftp-deploy-qes8fiy1/ramdisk/ramdisk.cpio.gz' initrd is at 0x78000000-0x78f52e50 Loading devicetree from '/mnt/tftp/910206/tftp-deploy-qes8fiy1/dtb/imx53-qsrb.dtb' commandline: console=ttymxc0,115200n8 Starting kernel at 0x72e32000, initrd at 0x78000000, oftree at 0x78f53000... Starting kernel in secure mode [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.167-cip26 (KernelCI@build-j1077747-arm-gcc-10-multi-v7-defconfig-rms94) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Tue Feb 21 12:53:12 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX53 Quick Start-R Board [ 0.000000] Memory policy: Data cache writeback [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0xcb800000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000070000000-0x000000008fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000090000000-0x00000000cfffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000070000000-0x000000008fffffff] [ 0.000000] node 0: [mem 0x00000000b0000000-0x00000000cfffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000070000000-0x00000000cfffffff] [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 261120 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 933264K/1048576K available (13312K kernel code, 2233K rwdata, 5348K rodata, 2048K init, 426K bss, 49776K reserved, 65536K cma-reserved, 457624K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] TrustZone Interrupt Controller (TZIC) initialized [ 0.000000] CPU identified as i.MX53, silicon rev 2.1 [ 0.000000] Switching to timer-based delay loop, resolution 25ns [ 0.000009] sched_clock: 32 bits at 40MHz, resolution 25ns, wraps every 53687091187ns [ 0.000030] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 47781511156 ns [ 0.002336] Console: colour dummy device 80x30 [ 0.002407] Calibrating delay loop (skipped), value calculated using timer frequency.. 80.00 BogoMIPS (lpj=400000) [ 0.002431] pid_max: default: 32768 minimum: 301 [ 0.002625] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.002645] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.003452] CPU: Testing write buffer coherency: ok [ 0.003520] CPU0: Spectre v2: using BPIALL workaround [ 0.003877] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.004721] Setting up static identity map for 0x70300000 - 0x703000ac [ 0.005835] rcu: Hierarchical SRCU implementation. [ 0.007966] EFI services will not be available. [ 0.008173] smp: Bringing up secondary CPUs ... [ 0.008188] smp: Brought up 1 node, 1 CPU [ 0.008199] SMP: Total of 1 processors activated (80.00 BogoMIPS). [ 0.008210] CPU: All CPU(s) started in SVC mode. [ 0.008791] devtmpfs: initialized [ 0.016364] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 [ 0.016690] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.016727] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.020684] pinctrl core: initialized pinctrl subsystem [ 0.022738] DMI not present or invalid. [ 0.023596] NET: Registered protocol family 16 [ 0.026352] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.031121] thermal_sys: Registered thermal governor 'step_wise' [ 0.031233] cpuidle: using governor menu [ 0.031717] No ATAGs? [ 0.031737] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.034139] Serial: AMBA PL011 UART driver [ 0.065872] imx53-pinctrl 53fa8000.iomuxc: initialized IMX pinctrl driver [ 0.102181] iommu: Default domain type: Translated [ 0.102869] vgaarb: loaded [ 0.103858] SCSI subsystem initialized [ 0.104565] usbcore: registered new interface driver usbfs [ 0.104651] usbcore: registered new interface driver hub [ 0.104711] usbcore: registered new device driver usb [ 0.106523] i2c i2c-1: IMX I2C adapter registered [ 0.108260] i2c i2c-0: IMX I2C adapter registered [ 0.109440] pps_core: LinuxPPS API ver. 1 registered [ 0.109459] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.109487] PTP clock support registered [ 0.113796] clocksource: Switched to clocksource mxc_timer1 [ 1.081849] NET: Registered protocol family 2 [ 1.082194] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.083024] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.083076] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 1.083125] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.083190] TCP: Hash tables configured (established 4096 bind 4096) [ 1.083361] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.083390] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.083552] NET: Registered protocol family 1 [ 1.084535] RPC: Registered named UNIX socket transport module. [ 1.084556] RPC: Registered udp transport module. [ 1.084565] RPC: Registered tcp transport module. [ 1.084573] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.084592] PCI: CLS 0 bytes, default 64 [ 1.085157] Trying to unpack rootfs image as initramfs... [ 2.239454] Freeing initrd memory: 15692K [ 2.240313] hw perfevents: enabled with armv7_cortex_a8 PMU driver, 5 counters available [ 2.241863] Initialise system trusted keyrings [ 2.242265] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.249207] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.250441] NFS: Registering the id_resolver key type [ 2.250518] Key type id_resolver registered [ 2.250531] Key type id_legacy registered [ 2.250647] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.250662] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.250703] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.251342] Key type asymmetric registered [ 2.251363] Asymmetric key parser 'x509' registered [ 2.251429] bounce: pool size: 64 pages [ 2.251487] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) [ 2.251502] io scheduler mq-deadline registered [ 2.251512] io scheduler kyber registered [ 2.287533] imx-sdma 63fb0000.sdma: Direct firmware load for imx/sdma/sdma-imx53.bin failed with error -2 [ 2.287575] imx-sdma 63fb0000.sdma: external firmware not found, using ROM firmware [ 2.339426] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.344133] SuperH (H)SCI(F) driver initialized [ 2.345124] 53fbc000.serial: ttymxc0 at MMIO 0x53fbc000 (irq = 47, base_baud = 4166666) is a IMX [ 3.024798] printk: console [ttymxc0] enabled [ 3.030821] msm_serial: driver initialized [ 3.035257] STMicroelectronics ASC driver initialized [ 3.041788] STM32 USART driver initialized [ 3.064965] brd: module loaded [ 3.077313] loop: module loaded [ 3.084040] ahci-imx 10000000.sata: supply ahci not found, using dummy regulator [ 3.091705] ahci-imx 10000000.sata: supply phy not found, using dummy regulator [ 3.099161] ahci-imx 10000000.sata: supply target not found, using dummy regulator [ 3.107121] ahci-imx 10000000.sata: hwmon0: sensor 'sata_ahci' [ 3.115149] ahci-imx 10000000.sata: SSS flag set, parallel bus scan disabled [ 3.122237] ahci-imx 10000000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 3.131182] ahci-imx 10000000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc [ 3.141305] scsi host0: ahci-imx [ 3.145087] ata1: SATA max UDMA/133 mmio [mem 0x10000000-0x10000fff] port 0x100 irq 44 [ 3.164173] CAN device driver interface [ 3.168994] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 3.212073] e1000e: Intel(R) PRO/1000 Network Driver [ 3.217206] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 3.223256] igb: Intel(R) Gigabit Ethernet Network Driver [ 3.228703] igb: Copyright (c) 2007-2014 Intel Corporation. [ 3.238724] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 3.246289] usbcore: registered new interface driver pegasus [ 3.252004] usbcore: registered new interface driver asix [ 3.257493] usbcore: registered new interface driver ax88179_178a [ 3.263625] usbcore: registered new interface driver cdc_ether [ 3.269538] usbcore: registered new interface driver smsc75xx [ 3.275381] usbcore: registered new interface driver smsc95xx [ 3.281166] usbcore: registered new interface driver net1080 [ 3.286889] usbcore: registered new interface driver cdc_subset [ 3.292845] usbcore: registered new interface driver zaurus [ 3.298548] usbcore: registered new interface driver cdc_ncm [ 3.307068] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.313613] ehci-pci: EHCI PCI platform driver [ 3.318187] ehci-platform: EHCI generic platform driver [ 3.323678] ehci-orion: EHCI orion driver [ 3.327948] SPEAr-ehci: EHCI SPEAr driver [ 3.332133] ehci-st: EHCI STMicroelectronics driver [ 3.337248] ehci-exynos: EHCI Exynos driver [ 3.341594] ehci-atmel: EHCI Atmel driver [ 3.345809] tegra-ehci: Tegra EHCI driver [ 3.349995] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.356257] ohci-pci: OHCI PCI platform driver [ 3.360774] ohci-platform: OHCI generic platform driver [ 3.366284] SPEAr-ohci: OHCI SPEAr driver [ 3.370465] ohci-st: OHCI STMicroelectronics driver [ 3.375568] ohci-atmel: OHCI Atmel driver [ 3.380449] usbcore: registered new interface driver usb-storage [ 3.393012] i2c /dev entries driver [ 3.414374] sdhci: Secure Digital Host Controller Interface driver [ 3.420582] sdhci: Copyright(c) Pierre Ossman [ 3.427188] Synopsys Designware Multimedia Card Interface Driver [ 3.434810] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.447234] sdhci-esdhc-imx 50020000.mmc: Got CD GPIO [ 3.452402] sdhci-esdhc-imx 50020000.mmc: Got WP GPIO [ 3.459235] ledtrig-cpu: registered to indicate activity on CPUs [ 3.466738] usbcore: registered new interface driver usbhid [ 3.472398] usbhid: USB HID core driver [ 3.481993] NET: Registered protocol family 10 [ 3.488112] Segment Routing with IPv6 [ 3.491874] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.498683] NET: Registered protocol family 17 [ 3.503154] can: controller area network core [ 3.507670] NET: Registered protocol family 29 [ 3.512120] can: raw protocol [ 3.515135] can: broadcast manager protocol [ 3.519331] can: netlink gateway - max_hops=1 [ 3.524477] Key type dns_resolver registered [ 3.529292] ThumbEE CPU extension supported. [ 3.533592] Registering SWP/SWPB emulation handler [ 3.538895] ata1: SATA link down (SStatus 0 SControl 300) [ 3.544453] ahci-imx 10000000.sata: no device found, disabling link. [ 3.550815] ahci-imx 10000000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 3.558131] mmc0: SDHCI controller on 50004000.mmc [50004000.mmc] using ADMA [ 3.566157] mmc2: SDHCI controller on 50020000.mmc [50020000.mmc] using ADMA [ 3.573943] Loading compiled-in X.509 certificates [ 3.606591] imx_usb 53f80000.usb: No over current polarity defined [ 3.616380] imx_usb 53f80200.usb: No over current polarity defined [ 3.626367] imx_usb 53f80000.usb: No over current polarity defined [ 3.636058] imx_usb 53f80200.usb: No over current polarity defined [ 3.644862] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.656543] imx_usb 53f80000.usb: No over current polarity defined [ 3.666277] imx_usb 53f80200.usb: No over current polarity defined [ 3.676996] Freeing unused kernel memory: 2048K [ 3.689506] Run /init as init process [ 3.719597] mmc0: host does not support reading read-only switch, assuming write-enable [ 3.737407] mmc0: new high speed SDHC card at address 0001 [ 3.751123] mmcblk0: mmc0:0001 SD16G 14.6 GiB [ 3.767158] imx_usb 53f80000.usb: No over current polarity defined [ 3.776957] imx_usb 53f80200.usb: No over current polarity defined Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 3.966371] udevd[89]: starting version 3.2.9 [ 3.972165] random: udevd: uninitialized urandom read (16 bytes read) [ 3.979868] random: udevd: uninitialized urandom read (16 bytes read) [ 3.986718] random: udevd: uninitialized urandom read (16 bytes read) [ 4.003186] udevd[89]: specified user 'tss' unknown [ 4.008557] udevd[89]: specified group 'tss' unknown [ 4.019069] udevd[90]: starting eudev-3.2.9 [ 5.411310] imx-ipuv3 18000000.ipu: IPUv3M probed [ 5.419418] imx_usb 53f80000.usb: No over current polarity defined [ 5.429139] imx_usb 53f80200.usb: No over current polarity defined [ 5.666717] imx_usb 53f80000.usb: No over current polarity defined [ 5.676485] imx_usb 53f80200.usb: No over current polarity defined [ 5.851675] usb_phy_generic usbphy-0: supply vcc not found, using dummy regulator [ 5.859653] usb_phy_generic usbphy-0: dummy supplies not allowed for exclusive requests [ 5.867962] usb_phy_generic usbphy-1: supply vcc not found, using dummy regulator [ 5.875685] usb_phy_generic usbphy-1: dummy supplies not allowed for exclusive requests [ 5.886859] imx_usb 53f80000.usb: No over current polarity defined [ 6.018048] imx_usb 53f80200.usb: No over current polarity defined [ 6.124090] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 6.129055] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 6.283929] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 6.315070] hub 1-0:1.0: USB hub found [ 6.335935] hub 1-0:1.0: 1 port detected [ 6.921938] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 6.930472] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.024670] imx-drm display-subsystem: bound 63ff0000.tve (ops imx_tve_ops [imx_tve]) [ 7.115707] [drm] Initialized imx-drm 1.0.0 20120507 for display-subsystem on minor 0 [ 7.280404] sgtl5000 1-000a: sgtl5000 revision 0x11 [ 7.292618] Console: switching to colour frame buffer device 128x48 [ 7.292884] sgtl5000 1-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.392743] imx-drm display-subsystem: [drm] fb0: imx-drmdrmfb frame buffer device done Saving random seed: [ 8.341523] random: dd: uninitialized urandom read (32 bytes read) OK Starting network: OK Starting dropbear sshd: [ 8.477316] random: dropbear: uninitialized urandom read (32 bytes read) OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-910206/environment . /lava-910206/environment / # /lava-910206/bin/lava-test-runner /lava-910206/0 /lava-910206/bin/lava-test-runner /lava-910206/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-910206/0/tests/0_dmesg + cat uuid + UUID=910206_1.5.2.3.1[ 9.105155] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh [ 9.167200] [ 9.223589] [ 9.280312] + set +x [ 9.291173] / # # export SHELL=/bin/sh # / # export SHELL=/bin/sh. /lava-910206/environment / # . /lava-910206/environment/lava-910206/bin/lava-test-runner /lava-910206/1 / # /lava-910206/bin/lava-test-runner /lava-910206/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-910206/1/tests/1_bootrr + cat uuid + UUID=910206_1.5.2.3.5[ 9.815281] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-910206/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto /lava-910206/1/../bin/lava-test-case [ 9.889747] /lava-910206/1/../bin/lava-test-case [ 9.943561] /lava-910206/1/../bin/lava-test-case [ 9.976210] + set +x [ 10.000480] / #