[Enter `^Ec?' for help] U-Boot 2021.10+dfsg-1+apertis10bv2023dev2b2 (Apr 18 2022 - 16:34:49 +0000) CPU: Freescale i.MX6Q rev1.2 at 792 MHz Reset cause: POR Model: Freescale i.MX6 Quad SABRE Lite Board Board: SABRE Lite I2C: ready DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from SPIFlash... SF: Detected gd25q16 with page size 256 Bytes, erase size 4 KiB, total 2 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: using phy at 7 FEC [PRIME], usb_ether Error: usb_ether address not set. starting USB... Bus usb@2184000: usb dr_mode not found Bus usb@2184200: USB EHCI 1.00 scanning bus usb@2184000 for devices... 1 USB Device(s) found scanning bus usb@2184200 for devices... 2 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found File System is consistent file found, deleting File System is consistent Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 DHCP client bound to address 192.168.201.34 (6 ms) => setenv serverip 192.168.201.1 setenv serverip 192.168.201.1 => tftp 0x10000000 9729774/tftp-deploy-svy4fyfo/kernel/zImage tftp 0x10000000 9729774/tftp-deploy-svy4fyfo/kernel/zImage Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9729774/tftp-deploy-svy4fyfo/kernel/zImage'. Load address: 0x10000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############ 6.5 MiB/s done Bytes transferred = 9703936 (941200 hex) => tftp 0x14000000 9729774/tftp-deploy-svy4fyfo/ramdisk/ramdisk.cpio.gz.uboot tftp 0x14000000 9729774/tftp-deploy-svy4fyfo/ramdisk/ramdisk.cpio.gz.uboot Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9729774/tftp-deploy-svy4fyfo/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x14000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################ 12 MiB/s done Bytes transferred = 12142782 (b948be hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x13f00000 9729774/tftp-deploy-svy4fyfo/dtb/imx6q-sabrelite.dtb tftp 0x13f00000 9729774/tftp-deploy-svy4fyfo/dtb/imx6q-sabrelite.dtb Using FEC device TFTP from server 192.168.201.1; our IP address is 192.168.201.34 Filename '9729774/tftp-deploy-svy4fyfo/dtb/imx6q-sabrelite.dtb'. Load address: 0x13f00000 Loading: *### 6.7 MiB/s done Bytes transferred = 42449 (a5d1 hex) => setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9729774/extract-nfsrootfs-h_iu0ou8,tcp,hard ip=dhcp' setenv bootargs 'console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9729774/extract-nfsrootfs-h_iu0ou8,tcp,hard ip=dhcp' => bootz 0x10000000 0x14000000 0x13f00000 bootz 0x10000000 0x14000000 0x13f00000 Kernel image @ 0x10000000 [ 0x000000 - 0x941200 ] ## Loading init Ramdisk from Legacy Image at 14000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 12142718 Bytes = 11.6 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 13f00000 Booting using the fdt blob at 0x13f00000 Using Device Tree in place at 13f00000, end 13f0d5d0 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.175-cip29-rt12 (KernelCI@build-j1227176-arm-gcc-10-multi-v7-defconfig-cvvrm) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Wed Mar 22 12:31:55 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 Quad SABRE Lite Board [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] OF: fdt: Reserved memory: unsupported node format, ignoring [ 0.000000] cma: Reserved 64 MiB at 0x4c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000010000000-0x000000003fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem [mem 0x0000000040000000-0x000000004fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000010000000-0x000000004fffffff] [ 0.000000] percpu: Embedded 16 pages/cpu s33612 r8192 d23732 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 260608 [ 0.000000] Kernel command line: console=ttymxc1,115200n8 root=/dev/nfs rw nfsroot=192.168.201.1:/var/lib/lava/dispatcher/tmp/9729774/extract-nfsrootfs-h_iu0ou8,tcp,hard ip=dhcp [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 936480K/1048576K available (14336K kernel code, 2330K rwdata, 5348K rodata, 2048K init, 415K bss, 46560K reserved, 65536K cma-reserved, 196608K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 errata 752271 769419 enabled [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 16 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 1024 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c7, AUX_CTRL 0x76470001 [ 0.000000] Switching to timer-based delay loop, resolution 333ns [ 0.000001] sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 715827882841ns [ 0.000017] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 637086815595 ns [ 0.003803] Console: colour dummy device 80x30 [ 0.003855] Calibrating delay loop (skipped), value calculated using timer frequency.. 6.00 BogoMIPS (lpj=30000) [ 0.003868] pid_max: default: 32768 minimum: 301 [ 0.004029] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004052] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.004682] CPU: Testing write buffer coherency: ok [ 0.004714] CPU0: Spectre v2: using BPIALL workaround [ 0.004964] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.005687] Setting up static identity map for 0x10300000 - 0x103000ac [ 0.007283] rcu: Hierarchical SRCU implementation. [ 0.010871] EFI services will not be available. [ 0.011179] smp: Bringing up secondary CPUs ... [ 0.011993] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.012006] CPU1: Spectre v2: using BPIALL workaround [ 0.012925] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.012939] CPU2: Spectre v2: using BPIALL workaround [ 0.013826] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.013840] CPU3: Spectre v2: using BPIALL workaround [ 0.013954] smp: Brought up 1 node, 4 CPUs [ 0.013966] SMP: Total of 4 processors activated (24.00 BogoMIPS). [ 0.013975] CPU: All CPU(s) started in SVC mode. [ 0.014532] devtmpfs: initialized [ 0.021836] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.022074] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022098] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.025228] pinctrl core: initialized pinctrl subsystem [ 0.027065] DMI not present or invalid. [ 0.027903] NET: Registered protocol family 16 [ 0.031490] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.033809] thermal_sys: Registered thermal governor 'step_wise' [ 0.033989] cpuidle: using governor menu [ 0.034167] CPU identified as i.MX6Q, silicon rev 1.2 [ 0.213169] vdd1p1: supplied by regulator-dummy [ 0.220530] vdd3p0: supplied by regulator-dummy [ 0.227825] vdd2p5: supplied by regulator-dummy [ 0.235178] vddarm: supplied by regulator-dummy [ 0.242659] vddpu: supplied by regulator-dummy [ 0.249843] vddsoc: supplied by regulator-dummy [ 0.586574] No ATAGs? [ 0.586716] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.586727] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.590922] imx6q-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver [ 0.597050] Serial: AMBA PL011 UART driver [ 0.599266] printk: console [ramoops-1] enabled [ 0.599471] pstore: Registered ramoops as persistent store backend [ 0.599478] ramoops: using 0x10000@0x30000000, ecc: 0 [ 0.631746] iommu: Default domain type: Translated [ 0.632176] vgaarb: loaded [ 0.633081] SCSI subsystem initialized [ 0.633644] usbcore: registered new interface driver usbfs [ 0.633698] usbcore: registered new interface driver hub [ 0.633739] usbcore: registered new device driver usb [ 0.635271] i2c i2c-0: IMX I2C adapter registered [ 0.636620] i2c i2c-1: IMX I2C adapter registered [ 0.637442] i2c i2c-2: IMX I2C adapter registered [ 0.638764] pps_core: LinuxPPS API ver. 1 registered [ 0.638770] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.638795] PTP clock support registered [ 0.642648] clocksource: Switched to clocksource mxc_timer1 [ 1.793362] NET: Registered protocol family 2 [ 1.793786] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 1.794937] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.794980] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 1.795068] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.795214] TCP: Hash tables configured (established 8192 bind 8192) [ 1.795425] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.795473] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 1.795654] NET: Registered protocol family 1 [ 1.796266] RPC: Registered named UNIX socket transport module. [ 1.796275] RPC: Registered udp transport module. [ 1.796279] RPC: Registered tcp transport module. [ 1.796282] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.796292] PCI: CLS 0 bytes, default 64 [ 1.796784] Trying to unpack rootfs image as initramfs... [ 2.758272] Freeing initrd memory: 11860K [ 2.758827] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 2.759228] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 2.761060] Initialise system trusted keyrings [ 2.761362] workingset: timestamp_bits=30 max_order=18 bucket_order=0 [ 2.767157] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.767895] NFS: Registering the id_resolver key type [ 2.767939] Key type id_resolver registered [ 2.767945] Key type id_legacy registered [ 2.768047] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 2.768055] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 2.768091] ntfs: driver 2.1.32 [Flags: R/O]. [ 2.768564] Key type asymmetric registered [ 2.768573] Asymmetric key parser 'x509' registered [ 2.768629] bounce: pool size: 64 pages [ 2.768667] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246) [ 2.768675] io scheduler mq-deadline registered [ 2.768681] io scheduler kyber registered [ 2.808439] mxs-dma 110000.dma-apbh: initialized [ 2.813274] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 [ 2.813292] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 2.874084] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled [ 2.878584] SuperH (H)SCI(F) driver initialized [ 2.879553] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 34, base_baud = 5000000) is a IMX [ 2.880599] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 81, base_baud = 5000000) is a IMX [ 2.880640] printk: console [ttymxc1] enabled [ 2.882133] msm_serial: driver initialized [ 2.882392] STMicroelectronics ASC driver initialized [ 2.884397] STM32 USART driver initialized [ 2.895271] panel-simple panel-lcd: supply power not found, using dummy regulator [ 2.895431] panel-simple panel-lcd: Specify missing connector_type [ 2.895808] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 2.904492] brd: module loaded [ 2.914379] loop: module loaded [ 2.918312] ahci-imx 2200000.sata: fsl,transmit-level-mV not specified, using 00000024 [ 2.918327] ahci-imx 2200000.sata: fsl,transmit-boost-mdB not specified, using 00000480 [ 2.918337] ahci-imx 2200000.sata: fsl,transmit-atten-16ths not specified, using 00002000 [ 2.918345] ahci-imx 2200000.sata: fsl,receive-eq-mdB not specified, using 05000000 [ 2.918424] ahci-imx 2200000.sata: supply ahci not found, using dummy regulator [ 2.918576] ahci-imx 2200000.sata: supply phy not found, using dummy regulator [ 2.918645] ahci-imx 2200000.sata: supply target not found, using dummy regulator [ 2.921507] ahci-imx 2200000.sata: SSS flag set, parallel bus scan disabled [ 2.921536] ahci-imx 2200000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 2.921553] ahci-imx 2200000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 2.923086] scsi host0: ahci-imx [ 2.923463] ata1: SATA max UDMA/133 mmio [mem 0x02200000-0x02203fff] port 0x100 irq 84 [ 2.935889] CAN device driver interface [ 2.937206] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.940744] pps pps0: new PPS source ptp0 [ 2.959534] fec 2188000.ethernet eth0: registered PHC device 0 [ 2.961025] e1000e: Intel(R) PRO/1000 Network Driver [ 2.961032] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 2.961089] igb: Intel(R) Gigabit Ethernet Network Driver [ 2.961095] igb: Copyright (c) 2007-2014 Intel Corporation. [ 2.967277] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver [ 2.967322] usbcore: registered new interface driver pegasus [ 2.967361] usbcore: registered new interface driver asix [ 2.967394] usbcore: registered new interface driver ax88179_178a [ 2.967426] usbcore: registered new interface driver cdc_ether [ 2.967466] usbcore: registered new interface driver smsc75xx [ 2.967515] usbcore: registered new interface driver smsc95xx [ 2.967549] usbcore: registered new interface driver net1080 [ 2.967583] usbcore: registered new interface driver cdc_subset [ 2.967612] usbcore: registered new interface driver zaurus [ 2.967682] usbcore: registered new interface driver cdc_ncm [ 2.971235] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.971243] ehci-pci: EHCI PCI platform driver [ 2.971279] ehci-platform: EHCI generic platform driver [ 2.971560] ehci-orion: EHCI orion driver [ 2.971778] SPEAr-ehci: EHCI SPEAr driver [ 2.971959] ehci-st: EHCI STMicroelectronics driver [ 2.972143] ehci-exynos: EHCI Exynos driver [ 2.972322] ehci-atmel: EHCI Atmel driver [ 2.972503] tegra-ehci: Tegra EHCI driver [ 2.972771] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.972791] ohci-pci: OHCI PCI platform driver [ 2.972843] ohci-platform: OHCI generic platform driver [ 2.973113] SPEAr-ohci: OHCI SPEAr driver [ 2.973302] ohci-st: OHCI STMicroelectronics driver [ 2.973491] ohci-atmel: OHCI Atmel driver [ 2.974533] usbcore: registered new interface driver usb-storage [ 2.982832] i2c /dev entries driver [ 3.002610] sdhci: Secure Digital Host Controller Interface driver [ 3.002617] sdhci: Copyright(c) Pierre Ossman [ 3.005354] Synopsys Designware Multimedia Card Interface Driver [ 3.007311] sdhci-pltfm: SDHCI platform and OF driver helper [ 3.008575] sdhci-esdhc-imx 2198000.mmc: Got CD GPIO [ 3.008626] sdhci-esdhc-imx 2198000.mmc: Got WP GPIO [ 3.008779] sdhci-esdhc-imx 219c000.mmc: Got CD GPIO [ 3.012419] ledtrig-cpu: registered to indicate activity on CPUs [ 3.013417] usbcore: registered new interface driver usbhid [ 3.013424] usbhid: USB HID core driver [ 3.019990] NET: Registered protocol family 10 [ 3.021041] Segment Routing with IPv6 [ 3.021130] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.021676] NET: Registered protocol family 17 [ 3.021692] can: controller area network core [ 3.021764] NET: Registered protocol family 29 [ 3.021773] can: raw protocol [ 3.021781] can: broadcast manager protocol [ 3.021791] can: netlink gateway - max_hops=1 [ 3.022176] Key type dns_resolver registered [ 3.024304] ThumbEE CPU extension supported. [ 3.024319] Registering SWP/SWPB emulation handler [ 3.024847] printk: console [ttymxc1]: printing thread started [ 3.025079] printk: console [ramoops-1]: printing thread started [ 3.025131] Loading compiled-in X.509 certificates [ 3.030320] pstore: Using crash dump compression: deflate [ 3.042748] mmc2: SDHCI controller on 2198000.mmc [2198000.mmc] using ADMA [ 3.051369] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.051520] panel-simple panel-lcd: Specify missing connector_type [ 3.053138] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.061622] imx_usb 2184200.usb: No over current polarity defined [ 3.065131] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 3.065155] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 [ 3.066635] mmc3: SDHCI controller on 219c000.mmc [219c000.mmc] using ADMA [ 3.102577] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 3.103184] hub 1-0:1.0: USB hub found [ 3.103218] hub 1-0:1.0: 1 port detected [ 3.105259] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C [ 3.109520] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.109655] panel-simple panel-lcd: Specify missing connector_type [ 3.111047] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.115300] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.115423] panel-simple panel-lcd: Specify missing connector_type [ 3.116832] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.118822] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 3.123973] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.124098] panel-simple panel-lcd: Specify missing connector_type [ 3.125509] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.235533] mmc2: new high speed SDHC card at address 59b4 [ 3.236292] mmcblk2: mmc2:59b4 SD 14.7 GiB [ 3.269357] ata1: SATA link down (SStatus 0 SControl 300) [ 3.269414] ahci-imx 2200000.sata: no device found, disabling link. [ 3.269421] ahci-imx 2200000.sata: pass ahci_imx..hotplug=1 to enable hotplug [ 3.281647] Micrel KSZ9021 Gigabit PHY 2188000.ethernet-1:07: attached PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=2188000.ethernet-1:07, irq=POLL) [ 3.366460] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 3.366467] GPT:7812499 != 30863359 [ 3.366472] GPT:Alternate GPT header not at the end of the disk. [ 3.366474] GPT:7812499 != 30863359 [ 3.366478] GPT: Use GNU Parted to correct GPT errors. [ 3.366515] mmcblk2: p1 p2 p3 [ 3.371706] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.371855] panel-simple panel-lcd: Specify missing connector_type [ 3.373382] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 3.402545] usb 1-1: new high-speed USB device number 2 using ci_hdrc [ 3.627344] hub 1-1:1.0: USB hub found [ 3.634722] hub 1-1:1.0: 3 ports detected [ 3.682152] panel-simple panel-lcd: supply power not found, using dummy regulator [ 3.682281] panel-simple panel-lcd: Specify missing connector_type [ 3.683757] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 6.393053] fec 2188000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 6.412619] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 6.442596] Sending DHCP requests ., OK [ 6.482649] IP-Config: Got DHCP answer from 192.168.201.1, my address is 192.168.201.34 [ 6.482674] IP-Config: Complete: [ 6.482680] device=eth0, hwaddr=00:19:b8:08:f1:10, ipaddr=192.168.201.34, mask=255.255.255.0, gw=192.168.201.1 [ 6.482705] host=imx6q-sabrelite-lava-cbg-4, domain=lava-rack, nis-domain=(none) [ 6.482718] bootserver=192.168.201.1, rootserver=192.168.201.1, rootpath= [ 6.482732] nameserver0=192.168.201.1 [ 6.490878] Freeing unused kernel memory: 2048K [ 6.542959] Run /init as init process Loading, please wait... Starting version 247.3-7+deb11u1 [ 7.374220] imx-ipuv3 2400000.ipu: IPUv3H probed [ 7.376402] imx-ipuv3 2800000.ipu: IPUv3H probed [ 7.382092] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.382286] panel-simple panel-lcd: Specify missing connector_type [ 7.384274] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.389305] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.389451] panel-simple panel-lcd: Specify missing connector_type [ 7.394039] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.418695] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.418852] panel-simple panel-lcd: Specify missing connector_type [ 7.476187] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.476318] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.476446] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.476540] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.496970] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.502353] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.502575] panel-simple panel-lcd: Specify missing connector_type [ 7.520932] etnaviv etnaviv: bound 130000.gpu (ops gpu_ops [etnaviv]) [ 7.521321] etnaviv etnaviv: bound 134000.gpu (ops gpu_ops [etnaviv]) [ 7.521880] etnaviv etnaviv: bound 2204000.gpu (ops gpu_ops [etnaviv]) [ 7.521968] etnaviv-gpu 130000.gpu: model: GC2000, revision: 5108 [ 7.543898] etnaviv-gpu 134000.gpu: model: GC320, revision: 5007 [ 7.543987] etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215 [ 7.544000] etnaviv-gpu 2204000.gpu: Ignoring GPU with VG and FE2.0 [ 7.547484] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 0 [ 7.563715] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.563825] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.563929] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.564008] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.565977] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.570889] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.571046] panel-simple panel-lcd: Specify missing connector_type [ 7.608436] caam 2100000.crypto: Entropy delay = 3200 [ 7.669236] caam 2100000.crypto: Instantiated RNG4 SH0 [ 7.671635] usb_phy_generic usbphynop1: supply vcc not found, using dummy regulator [ 7.671846] usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests [ 7.671981] usb_phy_generic usbphynop2: supply vcc not found, using dummy regulator [ 7.672102] usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests [ 7.686651] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.686716] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.686775] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.686821] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.730000] caam 2100000.crypto: Instantiated RNG4 SH1 [ 7.730028] caam 2100000.crypto: device ID = 0x0a16010000000000 (Era 4) [ 7.730036] caam 2100000.crypto: job rings = 2, qi = 0 [ 7.736850] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.742728] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.742902] panel-simple panel-lcd: Specify missing connector_type [ 7.757597] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.757700] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.757795] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.757866] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.801865] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.806744] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.806887] panel-simple panel-lcd: Specify missing connector_type [ 7.829679] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.829772] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) [ 7.829872] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) [ 7.829943] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) [ 7.843633] sgtl5000 0-000a: sgtl5000 revision 0x11 [ 7.866784] sgtl5000 0-000a: Using internal LDO instead of VDDD: check ER1 erratum [ 7.982808] panel-simple panel-lvds0: supply power not found, using dummy regulator [ 7.989830] panel-simple panel-lcd: supply power not found, using dummy regulator [ 7.990005] panel-simple panel-lcd: Specify missing connector_type [ 7.997851] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) [ 7.997923] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) Begin: Loading essential drivers [ 7.998008] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) ... [ 7.998056] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) done.[ 8.164077] caam algorithms registered in /proc/crypto [ 8.165453] caam 2100000.crypto: registering rng-caam Begin: Running /scripts/init-prem[ 8.167113] panel-simple panel-lvds0: supply power not found, using dummy regulator ount ... done. [ 8.172427] panel-simple panel-lcd: supply power not found, using dummy regulator Begin: Mounting root file system [ 8.172717] panel-simple panel-lcd: Specify missing connector_type ... Begin: Running /scripts/nfs-t[ 8.200369] imx-drm display-subsystem: bound imx-ipuv3-crtc.2 (ops imx_drm_exit [imxdrm]) op ... done. [ 8.200427] imx-drm display-subsystem: bound imx-ipuv3-crtc.3 (ops imx_drm_exit [imxdrm]) Begin: Running /scripts/nfs-premo[ 8.200481] imx-drm display-subsystem: bound imx-ipuv3-crtc.6 (ops imx_drm_exit [imxdrm]) unt ... Waiting up to 60 secs for[ 8.200528] imx-drm display-subsystem: bound imx-ipuv3-crtc.7 (ops imx_drm_exit [imxdrm]) any ethernet to become available[ 8.201901] panel-simple panel-lvds0: supply power not found, using dummy regulator Device /sys/class/net/eth0 foun[ 8.207206] panel-simple panel-lcd: supply power not found, using dummy regulator d done. [ 8.207376] panel-simple panel-lcd: Specify missing connector_type [ 8.350338] random: crng init done IP-Config: eth0 hardware address 00:19:b8:08:f1:10 mtu 1500 DHCP IP-Config: eth0 complete (dhcp from 192.168.201.1): address: 192.168.201.34 broadcast: 192.168.201.255 netmask: 255.255.255.0 gateway: 192.168.201.1 dns0 : 192.168.201.1 dns1 : 0.0.0.0 host : imx6q-sabrelite-lava-cbg-4 domain : lava-rack rootserver: 192.168.201.1 rootpath: filename : done. Begin: Running /scripts/nfs-bottom ... done. Begin: Running /scripts/init-bottom ... done. [ 9.432136] systemd[1]: System time before build time, advancing clock. [ 9.487599] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified) [ 9.488351] systemd[1]: Detected architecture arm. Welcome to Debian GNU/Linux 11 (bullseye)! [ 9.555758] systemd[1]: Set hostname to . [ OK ] Created slice system-getty.slice. [ 10.373340] systemd[1]: Queued start job for default target Graphical Interface. [ 10.375229] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling. [ 10.375253] systemd[1]: (This warning is only shown for the first unit using IP firewalling.) [ 10.375962] systemd[1]: Created slice system-getty.slice. [ OK ] Created slice system-modprobe.slice. [ 10.433979] systemd[1]: Created slice system-modprobe.slice. [ OK ] Created slice system-serial\x2dgetty.slice. [ 10.463938] systemd[1]: Created slice system-serial\x2dgetty.slice. [ OK ] Created slice User and Session Slice. [ 10.493734] systemd[1]: Created slice User and Session Slice. [ OK ] Started [0;1[ 10.533017] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. ;39mDispatch Password …ts to Console Directory Watch. [ OK ] Started Forward Password R…uests to Wall Directory Watch. [ 10.572951] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Local Encrypted Volumes. [ 10.612898] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped. [ 10.613178] systemd[1]: Reached target Local Encrypted Volumes. [ OK ] Reached targe[ 10.643496] systemd[1]: Reached target Paths. t Paths. [ OK ] Reached target Remote File Systems. [ 10.672970] systemd[1]: Reached target Remote File Systems. [ OK ] Reached target Slices. [ 10.702717] systemd[1]: Reached target Slices. [ OK ] Reached target Swap. [ 10.733109] systemd[1]: Reached target Swap. [ OK ] Listening on initctl Compatibility Named Pipe. [ 10.763833] systemd[1]: Listening on initctl Compatibility Named Pipe. [ OK ] Listening on [ 10.828798] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. Journal Socket (/dev/log[ 10.830400] systemd[1]: Listening on Journal Socket (/dev/log). ). [ OK ] Listening on Journal Socket. [ 10.884237] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Network Service Netlink Socket. [ 10.924989] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on udev Control Socket. [ 10.956184] systemd[1]: Listening on udev Control Socket. [ OK ] Listening on udev Kernel Socket. [ 10.994178] systemd[1]: Listening on udev Kernel Socket. Mounting Kernel[ 11.023898] systemd[1]: Condition check resulted in Huge Pages File System being skipped. Debug File System... [ 11.024837] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped. [ 11.030915] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Trace File System... [ 11.096547] systemd[1]: Mounting Kernel Trace File System... Starting Create list of st…odes for the curr[ 11.128156] systemd[1]: Starting Create list of static device nodes for the current kernel... ent kernel... Starting Load K[ 11.179593] systemd[1]: Starting Load Kernel Module configfs... ernel Module configfs... Starting Load Kernel Module drm... [ 11.216535] systemd[1]: Starting Load Kernel Module drm... Starting Load Kernel Module fuse... [ 11.246445] systemd[1]: Starting Load Kernel Module fuse... Starting Journa[ 11.275875] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. l Service... [ 11.279751] systemd[1]: Starting Journal Service... Starting Load Kernel Modules... [ 11.335145] systemd[1]: Starting Load Kernel Modules... Starting Remount Root and Kernel File Systems... [ 11.376405] systemd[1]: Starting Remount Root and Kernel File Systems... Starting Coldplug All udev Devices... [ 11.394341] systemd[1]: Starting Coldplug All udev Devices... [ OK ] Mounted Kernel Debug File System[0[ 11.438244] systemd[1]: Mounted Kernel Debug File System. m. [ OK ] Mounted Kernel Trace File System. [ 11.483263] systemd[1]: Mounted Kernel Trace File System. [ OK ] Finished Create list of st… nodes for the current kernel. [ 11.513709] systemd[1]: Finished Create list of static device nodes for the current kernel. [ OK ] Finished [0;[ 11.560982] systemd[1]: modprobe@configfs.service: Succeeded. [ 11.561630] systemd[1]: Finished Load Kernel Module configfs. 1;39mLoad Kernel Module configfs. [ OK ] Finished Load Kernel Module drm. [ 11.603978] systemd[1]: modprobe@drm.service: Succeeded. [ 11.604675] systemd[1]: Finished Load Kernel Module drm. [ OK ] Finished Load Kernel Module fuse. [ 11.644062] systemd[1]: modprobe@fuse.service: Succeeded. [ 11.644796] systemd[1]: Finished Load Kernel Module fuse. [ OK ] Started Journal Service. [ 11.683294] systemd[1]: Started Journal Service. [ OK ] Finished Load Kernel Modules. [ OK ] Finished Remount Root and Kernel File Systems. Mounting Kernel Configuration File System... Starting Flush Journal to Persistent Storage... Starting Load/Save Random Seed... Starting Apply Kernel Variables... [ 11.898991] systemd-journald[289]: Received client request to flush runtime journal. Starting Create System Users... [ OK ] Mounted Kernel Configuration File System. [ OK ] Finished Load/Save Random Seed. [ OK ] Finished Apply Kernel Variables. [ OK ] Finished Create System Users. Starting Create Static Device Nodes in /dev... [ OK ] Finished Flush Journal to Persistent Storage. [ OK ] Finished Create Static Device Nodes in /dev. [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Local File Systems. Starting Create Volatile Files and Directories... Starting Rule-based Manage…for Device Events and Files... [ OK ] Finished Coldplug All udev Devices. [ OK ] Started Rule-based Manager for Device Events and Files. Starting Network Service... [ OK ] Finished Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Finished Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target System Time Set. [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily apt download activities. [ OK ] Started Daily apt upgrade and clean activities. [ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems. [ OK ] Started Discard unused blocks once a week. [ OK ] Reached target Timers. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started D-Bus System Message Bus. Starting Remove Stale Onli…t4 Metadata Check Snapshots... Starting User Login Management... [ OK ] Found device /dev/ttymxc1. [ OK ] Started Network Name Resolution. [ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots. [ OK ] Started User Login Management. [ OK ] Reached target Network. [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Hardware activated USB gadget. [ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch. Starting Permit User Sessions... [ OK ] Finished Permit User Sessions. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttymxc1. [ OK ] Reached target Login Prompts. [ OK ] Reached target Multi-User System. [ OK ] Reached target Graphical Interface. Starting Update UTMP about System Runlevel Changes... [ OK ] Finished Update UTMP about System Runlevel Changes. Debian GNU/Linux 11 debian-bullseye-armhf ttymxc1 debian-bullseye-armhf login: root (automatic login) Linux debian-bullseye-armhf 5.10.175-cip29-rt12 #1 SMP Wed Mar 22 12:31:55 UTC 2023 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. / # / # export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9729774/extract-nfsrootfs-h_iu0ou8' export NFS_ROOTFS='/var/lib/lava/dispatcher/tmp/9729774/extract-nfsrootfs-h_iu0ou8' / # export NFS_SERVER_IP='192.168.201.1' export NFS_SERVER_IP='192.168.201.1' / # # # / # export SHELL=/bin/bash export SHELL=/bin/bash / # . /lava-9729774/environment . /lava-9729774/environment / # /lava-9729774/bin/lava-test-runner /lava-9729774/0 /lava-9729774/bin/lava-test-runner /lava-9729774/0 + export TESTRUN_ID=0_timesync-off + TESTRUN_ID=0_timesync-off + cd /lava-9729774/0/tests/0_timesync-off ++ cat uuid + UUID=9729774_1.6.2.4.1 + set +x + systemctl stop systemd-timesyncd + set +x + export TESTRUN_ID=1_kselftest-filesystems + TESTRUN_ID=1_kselftest-filesystems + cd /lava-9729774/0/tests/1_kselftest-filesystems ++ cat uuid + UUID=9729774_1.6.2.4.5 + set +x + cd ./automated/linux/kselftest/ + ./kselftest.sh -c filesystems -T '' -t kselftest_armhf.tar.gz -s True -u http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.175-cip29-rt12/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz -L '' -S skipfile-lkft.yaml -b imx6q-sabrelite -g cip-gitlab -e '' -p /opt/kselftests/mainline/ -n 1 -i 1 INFO: Generating a skipfile based on /lava-9729774/0/tests/1_kselftest-filesystems/automated/linux/kselftest/skipfile-lkft.yaml INFO: Using the following generated skipfile contents (until EOF): breakpoints:breakpoint_test breakpoints:step_after_suspend_test net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait INFO: EOF INFO: install_deps skipped --2023-03-22 12:51:10-- http://storage.kernelci.org/cip-gitlab/ci-pavel-linux-test/v5.10.175-cip29-rt12/arm/multi_v7_defconfig/gcc-10/kselftest.tar.xz Resolving storage.kernelci.org (storage.kernelci.org)... 52.250.1.28 Connecting to storage.kernelci.org (storage.kernelci.org)|52.250.1.28|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1410252 (1.3M) [application/octet-stream] Saving to: 'kselftest.tar.xz' kselftest.tar.xz 0%[ ] 0 --.-KB/s kselftest.tar.xz 3%[ ] 44.98K 160KB/s kselftest.tar.xz 6%[> ] 91.16K 161KB/s kselftest.tar.xz 10%[=> ] 139.24K 164KB/s kselftest.tar.xz 15%[==> ] 218.91K 185KB/s kselftest.tar.xz 19%[==> ] 265.09K 187KB/s kselftest.tar.xz 22%[===> ] 305.17K 179KB/s kselftest.tar.xz 24%[===> ] 334.86K 169KB/s kselftest.tar.xz 26%[====> ] 361.25K 156KB/s kselftest.tar.xz 27%[====> ] 380.11K 149KB/s kselftest.tar.xz 29%[====> ] 407.91K 137KB/s kselftest.tar.xz 30%[=====> ] 426.78K 131KB/s eta 7s kselftest.tar.xz 32%[=====> ] 446.57K 128KB/s eta 7s kselftest.tar.xz 33%[=====> ] 464.96K 124KB/s eta 7s kselftest.tar.xz 34%[=====> ] 480.51K 120KB/s eta 7s kselftest.tar.xz 35%[======> ] 494.65K 116KB/s eta 7s kselftest.tar.xz 37%[======> ] 515.86K 114KB/s eta 8s kselftest.tar.xz 39%[======> ] 541.32K 112KB/s eta 8s kselftest.tar.xz 41%[=======> ] 566.77K 105KB/s eta 8s kselftest.tar.xz 41%[=======> ] 576.67K 96.3KB/s eta 8s kselftest.tar.xz 43%[=======> ] 603.53K 85.7KB/s eta 7s kselftest.tar.xz 45%[========> ] 627.57K 79.9KB/s eta 7s kselftest.tar.xz 47%[========> ] 658.20K 76.7KB/s eta 7s kselftest.tar.xz 49%[========> ] 681.31K 73.8KB/s eta 7s kselftest.tar.xz 50%[=========> ] 695.45K 73.6KB/s eta 7s kselftest.tar.xz 52%[=========> ] 726.56K 75.6KB/s eta 7s kselftest.tar.xz 54%[=========> ] 744.94K 73.6KB/s eta 7s kselftest.tar.xz 55%[==========> ] 763.32K 76.0KB/s eta 7s kselftest.tar.xz 57%[==========> ] 787.36K 76.0KB/s eta 6s kselftest.tar.xz 59%[==========> ] 815.64K 78.0KB/s eta 6s kselftest.tar.xz 61%[===========> ] 843.92K 80.9KB/s eta 6s kselftest.tar.xz 63%[===========> ] 873.62K 82.6KB/s eta 6s kselftest.tar.xz 66%[============> ] 909.90K 84.1KB/s eta 5s kselftest.tar.xz 68%[============> ] 941.50K 85.2KB/s eta 5s kselftest.tar.xz 70%[=============> ] 975.43K 85.9KB/s eta 5s kselftest.tar.xz 72%[=============> ] 1001K 90.4KB/s eta 5s kselftest.tar.xz 75%[==============> ] 1.01M 89.1KB/s eta 3s kselftest.tar.xz 77%[==============> ] 1.04M 90.1KB/s eta 3s kselftest.tar.xz 79%[==============> ] 1.07M 91.7KB/s eta 3s kselftest.tar.xz 81%[===============> ] 1.10M 93.1KB/s eta 3s kselftest.tar.xz 83%[===============> ] 1.13M 94.8KB/s eta 2s kselftest.tar.xz 86%[================> ] 1.16M 97.0KB/s eta 2s kselftest.tar.xz 88%[================> ] 1.20M 100KB/s eta 2s kselftest.tar.xz 91%[=================> ] 1.23M 104KB/s eta 2s kselftest.tar.xz 94%[=================> ] 1.27M 108KB/s eta 1s kselftest.tar.xz 95%[==================> ] 1.29M 106KB/s eta 1s kselftest.tar.xz 98%[==================> ] 1.32M 105KB/s eta 1s kselftest.tar.xz 99%[==================> ] 1.34M 106KB/s eta 1s kselftest.tar.xz 100%[===================>] 1.34M 105KB/s in 14s 2023-03-22 12:51:24 (101 KB/s) - 'kselftest.tar.xz' saved [1410252/1410252] skiplist: ======================================== breakpoints:breakpoint_test breakpoints:step_after_suspend_test net:rtnetlink.sh net:tls netfilter:bridge_brouter.sh netfilter:nft_flowtable.sh netfilter:nft_trans_stress.sh pidfd:pidfd_wait ======================================== filesystems:devpts_pts ============== Tests to run =============== filesystems:devpts_pts ===========End Tests to run =============== [ 45.245754] kselftest: Running tests in filesystems TAP version 13 1..1 # selftests: filesystems: devpts_pts # Failed to perform TIOCGPTPEER ioctl ok 1 selftests: filesystems: devpts_pts filesystems_devpts_pts pass + ../../utils/send-to-lava.sh ./output/result.txt + set +x / #