Trying 127.0.0.1... Connected to 127.0.0.1. Escape character is '^]'. ser2net port 3023 device /dev/ttyimx6ul-14x14-evk-1 [115200 N81] (Debian GNU/Linux) U-Boot 2019.04-lf-5.4.y_v2019.04+g228843cdf5 (Feb 24 2020 - 11:58:52 +0000) CPU: Freescale i.MX6UL rev1.2 696 MHz (running at 396 MHz) CPU: Automotive temperature grade (-40C to 125C) at 30C Reset cause: POR Model: Freescale i.MX6 UltraLite 14x14 EVK Board Board: MX6UL 14x14 EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... *** Warning - bad CRC, using default environment Display: TFT43AB (480x272) Video: 480x272x24 In: serial Out: serial Err: serial switch to partitions #0, OK mmc1 is current device flash target is MMC:1 Net: Warning: ethernet@020b4000 using MAC address from ROM eth1: ethernet@020b4000 [PRIME] Warning: ethernet@02188000 using MAC address from ROM , eth0: ethernet@02188000 Fastboot: Normal Normal Boot Hit any key to stop autoboot: 3  0 => setenv autoload no setenv autoload no => setenv initrd_high 0xffffffff setenv initrd_high 0xffffffff => setenv fdt_high 0xffffffff setenv fdt_high 0xffffffff => dhcp dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 DHCP client bound to address 172.16.1.160 (1325 ms) => setenv serverip 59.144.98.45 setenv serverip 59.144.98.45 => tftp 0x80800000 1205512/tftp-deploy-4ll4bllp/kernel/zImage tftp 0x80800000 1205512/tftp-deploy-4ll4bllp/kernel/zImage Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1205512/tftp-deploy-4ll4bllp/kernel/zImage'. Load address: 0x80800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########### 4.9 MiB/s done Bytes transferred = 9691648 (93e200 hex) => tftp 0x86800000 1205512/tftp-deploy-4ll4bllp/ramdisk/ramdisk.cpio.gz.uboot tftp 0x86800000 1205512/tftp-deploy-4ll4bllp/ramdisk/ramdisk.cpio.gz.uboot Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1205512/tftp-deploy-4ll4bllp/ramdisk/ramdisk.cpio.gz.uboot'. Load address: 0x86800000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ######################################################## 5.1 MiB/s done Bytes transferred = 16077105 (f55131 hex) => setenv initrd_size ${filesize} setenv initrd_size ${filesize} => tftp 0x83000000 1205512/tftp-deploy-4ll4bllp/dtb/imx6ul-14x14-evk.dtb tftp 0x83000000 1205512/tftp-deploy-4ll4bllp/dtb/imx6ul-14x14-evk.dtb Using ethernet@020b4000 device TFTP from server 59.144.98.45; our IP address is 172.16.1.160; sending through gateway 172.16.1.4 Filename '1205512/tftp-deploy-4ll4bllp/dtb/imx6ul-14x14-evk.dtb'. Load address: 0x83000000 Loading: *### 4.2 MiB/s done Bytes transferred = 30855 (7887 hex) => setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' setenv bootargs 'console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp' => bootz 0x80800000 0x86800000 0x83000000 bootz 0x80800000 0x86800000 0x83000000 Kernel image @ 0x80800000 [ 0x000000 - 0x93e200 ] ## Loading init Ramdisk from Legacy Image at 86800000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 16077041 Bytes = 15.3 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 83000000 Booting using the fdt blob at 0x83000000 Using Device Tree in place at 83000000, end 8300a886 ft_system_setup for mx6 Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.177-cip31 (KernelCI@build-j1384315-arm-gcc-10-multi-v7-defconfig-n7ltb) (arm-linux-gnueabihf-gcc (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Fri Apr 21 12:00:15 UTC 2023 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Freescale i.MX6 UltraLite 14x14 EVK Board [ 0.000000] earlycon: ec_imx6q0 at MMIO 0x02020000 (options '') [ 0.000000] printk: bootconsole [ec_imx6q0] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: UEFI not found. [ 0.000000] cma: Reserved 64 MiB at 0x9c000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Normal empty [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff] [ 0.000000] percpu: Embedded 20 pages/cpu s49868 r8192 d23860 u81920 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttymxc0,115200n8 root=/dev/ram0 console_msg_format=syslog earlycon ip=dhcp <6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) <6>[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off <6>[ 0.000000] Memory: 414044K/524288K available (13312K kernel code, 2237K rwdata, 5348K rodata, 2048K init, 426K bss, 44708K reserved, 65536K cma-reserved, 0K highmem) <6>[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 <6>[ 0.000000] rcu: Hierarchical RCU implementation. <6>[ 0.000000] rcu: RCU event tracing is enabled. <6>[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=16 to nr_cpu_ids=1. <6>[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. <6>[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 <6>[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 <6>[ 0.000000] Switching to timer-based delay loop, resolution 41ns <6>[ 0.000018] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns <6>[ 0.008104] clocksource: mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns <6>[ 0.025120] Console: colour dummy device 80x30 <6>[ 0.027081] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) <6>[ 0.037697] pid_max: default: 32768 minimum: 301 <6>[ 0.042835] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.050118] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) <6>[ 0.059554] CPU: Testing write buffer coherency: ok <6>[ 0.063854] CPU0: update cpu_capacity 1024 <6>[ 0.067543] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>[ 0.075289] Setting up static identity map for 0x80300000 - 0x803000ac <6>[ 0.082693] rcu: Hierarchical SRCU implementation. <6>[ 0.091082] EFI services will not be available. <6>[ 0.093475] smp: Bringing up secondary CPUs ... <6>[ 0.097924] smp: Brought up 1 node, 1 CPU <6>[ 0.102101] SMP: Total of 1 processors activated (48.00 BogoMIPS). <6>[ 0.108573] CPU: All CPU(s) started in SVC mode. <6>[ 0.114479] devtmpfs: initialized <6>[ 0.130925] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 <6>[ 0.136546] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns <6>[ 0.146291] futex hash table entries: 256 (order: 2, 16384 bytes, linear) <6>[ 0.157975] pinctrl core: initialized pinctrl subsystem <6>[ 0.164373] DMI not present or invalid. <6>[ 0.167836] NET: Registered protocol family 16 <6>[ 0.174914] DMA: preallocated 256 KiB pool for atomic coherent allocations <6>[ 0.184818] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.185013] cpuidle: using governor menu <6>[ 0.429613] vdd3p0: supplied by regulator-dummy <6>[ 0.444130] cpu: supplied by regulator-dummy <6>[ 0.458958] vddsoc: supplied by regulator-dummy <6>[ 0.877794] No ATAGs? <6>[ 0.878907] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>[ 0.885862] hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ 0.900603] imx6ul-pinctrl 20e0000.pinctrl: initialized IMX pinctrl driver <6>[ 0.915008] Serial: AMBA PL011 UART driver <6>[ 0.987806] iommu: Default domain type: Translated <6>[ 0.990982] vgaarb: loaded <5>[ 0.995222] SCSI subsystem initialized <6>[ 0.998529] usbcore: registered new interface driver usbfs <6>[ 1.002951] usbcore: registered new interface driver hub <6>[ 1.008596] usbcore: registered new device driver usb <6>[ 1.017126] i2c i2c-0: IMX I2C adapter registered <6>[ 1.021389] i2c i2c-1: IMX I2C adapter registered <6>[ 1.027051] pps_core: LinuxPPS API ver. 1 registered <6>[ 1.029561] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 1.038898] PTP clock support registered <6>[ 1.051448] clocksource: Switched to clocksource mxc_timer1 <6>[ 3.304637] NET: Registered protocol family 2 <6>[ 3.306943] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) <6>[ 3.315930] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) <6>[ 3.322676] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) <6>[ 3.330619] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) <6>[ 3.338124] TCP: Hash tables configured (established 4096 bind 4096) <6>[ 3.344799] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 3.351444] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) <6>[ 3.358956] NET: Registered protocol family 1 <6>[ 3.365058] RPC: Registered named UNIX socket transport module. <6>[ 3.369332] RPC: Registered udp transport module. <6>[ 3.374432] RPC: Registered tcp transport module. <6>[ 3.379246] RPC: Registered tcp NFSv4.1 backchannel transport module. <6>[ 3.386011] PCI: CLS 0 bytes, default 64 <6>[ 3.391203] Trying to unpack rootfs image as initramfs... <6>[ 6.400514] Freeing initrd memory: 15704K <6>[ 6.403409] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available <5>[ 6.414086] Initialise system trusted keyrings <6>[ 6.416888] workingset: timestamp_bits=30 max_order=17 bucket_order=0 <6>[ 6.438672] squashfs: version 4.0 (2009/01/31) Phillip Lougher <5>[ 6.444032] NFS: Registering the id_resolver key type <5>[ 6.447356] Key type id_resolver registered <5>[ 6.451800] Key type id_legacy registered <6>[ 6.456232] nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>[ 6.462982] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... <6>[ 6.470652] ntfs: driver 2.1.32 [Flags: R/O]. <5>[ 6.476489] Key type asymmetric registered <5>[ 6.479535] Asymmetric key parser 'x509' registered <6>[ 6.484863] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) <6>[ 6.492376] io scheduler mq-deadline registered <6>[ 6.497106] io scheduler kyber registered <4>[ 6.553726] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 6.587682] mxs-dma 1804000.dma-apbh: initialized <4>[ 6.618741] imx-sdma 20ec000.sdma: Direct firmware load for imx/sdma/sdma-imx6q.bin failed with error -2 <6>[ 6.625864] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware <6>[ 6.761254] Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled <6>[ 6.775513] SuperH (H)SCI(F) driver 鹥ѥ���镑5 <6>[ 6.779619] printk: console [ttymxc0] enabled <6>[ 6.779619] printk: console [ttymxc0] enabled <6>[ 6.787047] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.787047] printk: bootconsole [ec_imx6q0] disabled <6>[ 6.800099] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 73, base_baud = 5000000) is a IMX <6>[ 6.812664] msm_serial: driver initialized <6>[ 6.817724] STMicroelectronics ASC driver initialized <6>[ 6.827113] STM32 USART driver initialized <4>[ 6.854183] panel-simple panel: supply power not found, using dummy regulator <4>[ 6.862115] panel-simple panel: Specify missing connector_type <6>[ 6.893682] brd: module loaded <6>[ 6.914992] loop: module loaded <6>[ 6.953870] CAN device driver interface <6>[ 6.960744] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded <6>[ 6.970195] pps pps0: new PPS source ptp0 <6>[ 7.119568] fec 20b4000.ethernet eth0: registered PHC device 0 <6>[ 7.129198] pps pps1: new PPS source ptp1 <6>[ 9.357099] fec 2188000.ethernet eth1: registered PHC device 1 <6>[ 9.366322] e1000e: Intel(R) PRO/1000 Network Driver <6>[ 9.371724] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. <6>[ 9.378113] igb: Intel(R) Gigabit Ethernet Network Driver <6>[ 9.383865] igb: Copyright (c) 2007-2014 Intel Corporation. <6>[ 9.403136] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver <6>[ 9.410973] usbcore: registered new interface driver pegasus <6>[ 9.417195] usbcore: registered new interface driver asix <6>[ 9.423063] usbcore: registered new interface driver ax88179_178a <6>[ 9.429525] usbcore: registered new interface driver cdc_ether <6>[ 9.435818] usbcore: registered new interface driver smsc75xx <6>[ 9.442014] usbcore: registered new interface driver smsc95xx <6>[ 9.448147] usbcore: registered new interface driver net1080 <6>[ 9.454237] usbcore: registered new interface driver cdc_subset <6>[ 9.460526] usbcore: registered new interface driver zaurus <6>[ 9.466650] usbcore: registered new interface driver cdc_ncm <6>[ 9.480381] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>[ 9.487368] ehci-pci: EHCI PCI platform driver <6>[ 9.492279] ehci-platform: EHCI generic platform driver <6>[ 9.498506] ehci-orion: EHCI orion driver <6>[ 9.503414] SPEAr-ehci: EHCI SPEAr driver <6>[ 9.508129] ehci-st: EHCI STMicroelectronics driver <6>[ 9.513829] ehci-exynos: EHCI Exynos driver <6>[ 9.518717] ehci-atmel: EHCI Atmel driver <6>[ 9.523526] tegra-ehci: Tegra EHCI driver <6>[ 9.528301] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver <6>[ 9.534910] ohci-pci: OHCI PCI platform driver <6>[ 9.539805] ohci-platform: OHCI generic platform driver <6>[ 9.546059] SPEAr-ohci: OHCI SPEAr driver <6>[ 9.550800] ohci-st: OHCI STMicroelectronics driver <6>[ 9.556549] ohci-atmel: OHCI Atmel driver <6>[ 9.563450] usbcore: registered new interface driver usb-storage <6>[ 9.588377] i2c /dev entries driver <6>[ 9.639767] sdhci: Secure Digital Host Controller Interface driver <6>[ 9.646406] sdhci: Copyright(c) Pierre Ossman <6>[ 9.657354] Synopsys Designware Multimedia Card Interface Driver <6>[ 9.668319] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 9.687377] sdhci-esdhc-imx 2190000.mmc: Got CD GPIO <6>[ 9.698800] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 9.707799] usbcore: registered new interface driver usbhid <6>[ 9.713786] usbhid: USB HID core driver <6>[ 9.734021] NET: Registered protocol family 10 <6>[ 9.741770] Segment Routing with IPv6 <6>[ 9.745928] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver <6>[ 9.753717] NET: Registered protocol family 17 <6>[ 9.758487] can: controller area network core <6>[ 9.763434] NET: Registered protocol family 29 <6>[ 9.768168] can: raw protocol <6>[ 9.771502] can: broadcast manager protocol <6>[ 9.775992] can: netlink gateway - max_hops=1 <5>[ 9.781874] Key type dns_resolver registered <6>[ 9.790582] ThumbEE CPU extension supported. <5>[ 9.795327] Registering SWP/SWPB emulation handler <5>[ 9.802663] Loading compiled-in X.509 certificates <6>[ 9.833563] mmc1: SDHCI controller on 2194000.mmc [2194000.mmc] using ADMA <4>[ 9.845250] pwm-backlight backlight-display: supply power not found, using dummy regulator <6>[ 9.854755] mmc0: SDHCI controller on 2190000.mmc [2190000.mmc] using ADMA <4>[ 9.866152] panel-simple panel: supply power not found, using dummy regulator <4>[ 9.874029] panel-simple panel: Specify missing connector_type <4>[ 9.884343] imx_usb 2184000.usb: No over current polarity defined <6>[ 9.911833] ci_hdrc ci_hdrc.1: EHCI Host Controller <6>[ 9.917072] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 1 <6>[ 9.954319] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 <6>[ 9.964290] hub 1-0:1.0: USB hub found <6>[ 9.968547] hub 1-0:1.0: 1 port detected <6>[ 9.980031] imx_thermal 20c8000.anatop:tempmon: Automotive CPU temperature grade - max:125C critical:120C passive:115C <4>[ 10.001207] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 10.014671] panel-simple panel: supply power not found, using dummy regulator <4>[ 10.022516] panel-simple panel: Specify missing connector_type <4>[ 10.034377] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 10.047256] panel-simple panel: supply power not found, using dummy regulator <4>[ 10.055176] panel-simple panel: Specify missing connector_type <4>[ 10.061589] mmc1: host does not support reading read-only switch, assuming write-enable <6>[ 10.076592] mmc1: new high speed SDHC card at address aaaa <6>[ 10.083621] mmcblk1: mmc1:aaaa SS16G 14.8 GiB <6>[ 10.097280] mmcblk1: p1 p2 <4>[ 10.107326] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 10.120876] panel-simple panel: supply power not found, using dummy regulator <4>[ 10.128865] panel-simple panel: Specify missing connector_type <6>[ 10.169754] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:01: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:01, irq=POLL) <6>[ 10.279667] Micrel KSZ8081 or KSZ8091 20b4000.ethernet-1:02: attached PHY driver [Micrel KSZ8081 or KSZ8091] (mii_bus:phy_addr=20b4000.ethernet-1:02, irq=POLL) <6>[ 13.284762] fec 20b4000.ethernet eth0: Link is Up - 100Mbps/Full - flow control off <6>[ 13.293495] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready <5>[ 13.323961] Sending DHCP requests ..., OK <6>[ 21.268568] IP-Config: Got DHCP answer from 172.16.1.4, my address is 172.16.1.160 <6>[ 21.276611] IP-Config: Complete: <6>[ 21.280170] device=eth0, hwaddr=00:04:9f:05:20:41, ipaddr=172.16.1.160, mask=255.255.255.0, gw=172.16.1.4 <6>[ 21.290555] host=172.16.1.160, domain=example.org, nis-domain=(none) <6>[ 21.297722] bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath= <6>[ 21.297749] nameserver0=172.16.1.4 <6>[ 21.329030] Freeing unused kernel memory: 2048K <6>[ 21.344721] Run /init as init process Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: <30>[ 21.597442] udevd[126]: starting version 3.2.9 <5>[ 21.604500] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 21.612480] random: udevd: uninitialized urandom read (16 bytes read) <5>[ 21.619441] random: udevd: uninitialized urandom read (16 bytes read) <27>[ 21.640988] udevd[126]: specified user 'tss' unknown <27>[ 21.647026] udevd[126]: specified group 'tss' unknown <30>[ 21.663681] udevd[127]: starting eudev-3.2.9 <4>[ 24.813584] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 24.965293] panel-simple panel: supply power not found, using dummy regulator <4>[ 24.973189] panel-simple panel: Specify missing connector_type <6>[ 25.574143] caam 2140000.crypto: RNG4 SH0 was previously instantiated without prediction resistance. Tearing it down <6>[ 25.585170] caam 2140000.crypto: Deinstantiated RNG4 SH0 <6>[ 25.590779] caam 2140000.crypto: Instantiated RNG4 SH0 <6>[ 25.596254] caam 2140000.crypto: RNG4 SH1 was previously instantiated without prediction resistance. Tearing it down <6>[ 25.607094] caam 2140000.crypto: Deinstantiated RNG4 SH1 <6>[ 25.612723] caam 2140000.crypto: Instantiated RNG4 SH1 <6>[ 25.618143] caam 2140000.crypto: device ID = 0x0a16030000000000 (Era 8) <6>[ 25.625055] caam 2140000.crypto: job rings = 3, qi = 0 <4>[ 25.645049] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 25.793067] panel-simple panel: supply power not found, using dummy regulator <4>[ 25.800811] panel-simple panel: Specify missing connector_type <6>[ 26.425140] spi-nor spi4.0: n25q256a (32768 Kbytes) <4>[ 26.496884] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 26.561631] panel-simple panel: supply power not found, using dummy regulator <4>[ 26.569423] panel-simple panel: Specify missing connector_type <6>[ 26.668390] gpio@0 enforce active low on chipselect handle <4>[ 26.749728] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 26.812916] panel-simple panel: supply power not found, using dummy regulator <4>[ 26.820666] panel-simple panel: Specify missing connector_type <6>[ 28.402816] caam algorithms registered in /proc/crypto <6>[ 28.411970] caam 2140000.crypto: caam pkc algorithms registered in /proc/crypto <6>[ 28.419582] caam 2140000.crypto: registering rng-caam <4>[ 28.431690] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 28.450552] panel-simple panel: supply power not found, using dummy regulator <4>[ 28.458486] panel-simple panel: Specify missing connector_type <5>[ 28.467919] random: crng init done <4>[ 28.493820] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 28.512141] panel-simple panel: supply power not found, using dummy regulator <4>[ 28.519916] panel-simple panel: Specify missing connector_type <4>[ 28.573978] pwm-backlight backlight-display: supply power not found, using dummy regulator <4>[ 28.592344] panel-simple panel: supply power not found, using dummy regulator <4>[ 28.600093] panel-simple panel: Specify missing connector_type done Saving random seed: OK Starting network: ip: RTNETLINK answers: File exists FAIL Starting dropbear sshd: OK /bin/sh: can't access tty; job control turned off / # / # # # / # export SHELL=/bin/sh export SHELL=/bin/sh / # . /lava-1205512/environment . /lava-1205512/environment / # /lava-1205512/bin/lava-test-runner /lava-1205512/0 /lava-1205512/bin/lava-test-runner /lava-1205512/0 + export 'TESTRUN_ID=0_dmesg' + cd /lava-1205512/0/tests/0_dmesg + cat uuid + UUID=1205512_1.5.2.4.1<8>[ 34.648425] + set +x + KERNELCI_LAVA=y /bin/sh /opt/kernelci/dmesg.sh <8>[ 34.715696] <8>[ 34.776914] <8>[ 34.838374] + set +x <8>[ 34.849653] # / # #export SHELL=/bin/sh / # export SHELL=/bin/sh . /lava-1205512/environment / # . /lava-1205512/environment /lava-1205512/bin/lava-test-runner /lava-1205512/1 / # /lava-1205512/bin/lava-test-runner /lava-1205512/1 + export 'TESTRUN_ID=1_bootrr' + cd /lava-1205512/1/tests/1_bootrr + cat uuid + UUID=1205512_1.5.2.4.5<8>[ 40.615737] + set +x + export 'PATH=/opt/bootrr/libexec/bootrr/helpers:/lava-1205512/1/../bin:/sbin:/usr/sbin:/bin:/usr/bin' + cd /opt/bootrr/libexec/bootrr + sh helpers/bootrr-auto regulator-can-3v3 backlight-display sound panel 2090000.flexcan 2094000.flexcan 21c8000.lcdif /lava-1205512/1/../bin/lava-test-case <8>[ 41.721304] /lava-1205512/1/../bin/lava-test-case <8>[ 41.778010] /lava-1205512/1/../bin/lava-test-case <8>[ 41.812611] + set +x <8>[ 41.838279] / #